scholarly journals Mechanical design of the highly porous cuttlebone: A bioceramic hard buoyancy tank for cuttlefish

2020 ◽  
Vol 117 (38) ◽  
pp. 23450-23459
Author(s):  
Ting Yang ◽  
Zian Jia ◽  
Hongshun Chen ◽  
Zhifei Deng ◽  
Wenkun Liu ◽  
...  
Keyword(s):  
Energy Absorption ◽  
Mechanical Performance ◽  
Mechanical Design ◽  
Water Pressure ◽  
Three Dimensional ◽  
High Energy ◽  
Image Correlation ◽  
Design Strategies ◽  
Stress Concentrations ◽  
Damage Tolerant

Cuttlefish, a unique group of marine mollusks, produces an internal biomineralized shell, known as cuttlebone, which is an ultra-lightweight cellular structure (porosity, ∼93 vol%) used as the animal’s hard buoyancy tank. Although cuttlebone is primarily composed of a brittle mineral, aragonite, the structure is highly damage tolerant and can withstand water pressure of about 20 atmospheres (atm) for the speciesSepia officinalis. Currently, our knowledge on the structural origins for cuttlebone’s remarkable mechanical performance is limited. Combining quantitative three-dimensional (3D) structural characterization, four-dimensional (4D) mechanical analysis, digital image correlation, and parametric simulations, here we reveal that the characteristic chambered “wall–septa” microstructure of cuttlebone, drastically distinct from other natural or engineering cellular solids, allows for simultaneous high specific stiffness (8.4 MN⋅m/kg) and energy absorption (4.4 kJ/kg) upon loading. We demonstrate that the vertical walls in the chambered cuttlebone microstructure have evolved an optimal waviness gradient, which leads to compression-dominant deformation and asymmetric wall fracture, accomplishing both high stiffness and high energy absorption. Moreover, the distribution of walls is found to reduce stress concentrations within the horizontal septa, facilitating a larger chamber crushing stress and a more significant densification. The design strategies revealed here can provide important lessons for the development of low-density, stiff, and damage-tolerant cellular ceramics.

scholarly journals Experimental Study on Angular Flexural Performance of Multiaxis Three Dimensional (3D) Polymeric Carbon Fiber/Cementitious Concretes

Polymers ◽  
2021 ◽  
Vol 13 (18) ◽  
pp. 3073
Author(s):  
Huseyin Ozdemir ◽  
Kadir Bilisik
Keyword(s):  
Carbon Fiber ◽  
Flexural Strength ◽  
Energy Absorption ◽  
Carbon Fibers ◽  
Three Dimensional ◽  
Flexural Performance ◽  
Fiber Concrete ◽  
Filament Bundles ◽  
Damage Tolerant ◽  
Polymeric Carbon

Multiaxis three-dimensional (3D) continuous polymeric carbon fiber/cementitious concretes were introduced. Their angular (off-axis) flexural properties were experimentally studied. It was found that the placement of the continuous carbon fibers and their in-plane angular orientations in the pristine concrete noticeably influenced the angular flexural strength and the energy absorption behavior of the multiaxis 3D concrete composite. The off-axis flexural strength of the uniaxial (C-1D-(0°)), biaxial (C-2D-(0°), and C-2D-(90°)), and multiaxial (C-4D-(0°), C-4D-(+45°) and C-4D-(−45°)) concrete composites were outstandingly higher (from 36.84 to 272.43%) than the neat concrete. Their energy absorption capacities were superior compared to the neat concrete. Fractured four directional polymeric carbon fiber/cementitious matrix concretes limited brittle matrix failure and a broom-like fracture phenomenon on the filament bundles, filament-matrix debonding and splitting, and minor filament entanglement. Multiaxis 3D polymeric carbon fiber concrete, especially the C-4D structure, controlled the crack phenomena and was considered a damage-tolerant material compared to the neat concrete.

Mechanical performance of three-dimensional printed sandwich composite with a high-flexible core

2021 ◽  
pp. 146442072110117
Author(s):  
Waleed Ahmed ◽  
Sidra Ahmed ◽  
Fady Alnajjar ◽  
Essam Zaneldin
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Mechanical Performance ◽  
Flexural Rigidity ◽  
Peak Load ◽  
Three Dimensional ◽  
High Energy ◽  
Element Analysis ◽  
High Stiffness ◽  
Flexible Core

This paper aims to investigate experimentally and using finite element analysis the performance of using three-dimensional printing technology to produce a composite sandwich panel that is made of the high-flexible core as well as with high stiffness upper and lower surfaces made of a glass fiber reinforced composite filament. There are many advantages of using sandwich structures in many applications, especially the aerospace field, where the high stiffness to strength and the lightweight is the most preferred in such applications. The conventional manufacturing methods that are used to produce sandwich panels are limited to particular core geometry, whereas manufacturing a composite core is not possible by these traditional production methods. So by using additive manufacturing technology, it becomes more applicable to design a combination of different geometries and materials to achieve properties that have never been made before, especially combining flexibility and high energy absorption keeping high strength to failure. A central deflection to a length of 0.26 is observed within the elastic zone, a remarkable ratio in beams that reflects the three-dimensional printed sandwich beams’ capability with a highly flexible core to absorb energy that would open doors for many industrial applications that is attributed to the lowest flexural rigidity (167E-3Pa · m4) of the sandwich by using the TriHex infill pattern. In contrast, the Gyroid infill structure could afford the highest central load (0.264 kN). At the peak load applied on the sandwich beam, a maximum error of 5.4% is estimated by finite element analysis lower than the experimental values.

scholarly journals POSSIBILITY OF FORMING A LARGE DCC IN ULTRA-RELATIVISTIC HEAVY-ION COLLISIONS

2000 ◽  
Vol 15 (15) ◽  
pp. 2269-2288
Author(s):  
SANATAN DIGAL ◽  
RAJARSHI RAY ◽  
SUPRATIM SENGUPTA ◽  
AJIT M. SRIVASTAVA
Keyword(s):  
Three Dimensional ◽  
Thermal Fluctuations ◽  
Heavy Ion ◽  
High Energy ◽  
Chiral Condensate ◽  
Relativistic Heavy Ion Collisions ◽  
Maximum Temperature ◽  
Chiral Field ◽  
Heavy Nuclei ◽  
True Vacuum

We demonstrate the possibility of forming a single, large domain of disoriented chiral condensate (DCC) in a heavy-ion collision. In our scenario, rapid initial heating of the parton system provides a driving force for the chiral field, moving it away from the true vacuum and forcing it to go to the opposite point on the vacuum manifold. This converts the entire hot region into a single DCC domain. Subsequent rolling down of the chiral field to its true vacuum will then lead to emission of a large number of (approximately) coherent pions. The requirement of suppression of thermal fluctuations to maintain the (approximate) coherence of such a large DCC domain, favors three-dimensional expansion of the plasma over the longitudinal expansion even at very early stages of evolution. This also constrains the maximum temperature of the system to lie within a window. We roughly estimate this window to be about 200–400 MeV. These results lead us to predict that extremely high energy collisions of very small nuclei (possibly hadrons) are better suited for observing signatures of a large DCC. Another possibility is to focus on peripheral collisions of heavy nuclei.

scholarly journals The Hydromechanical Interplay in the Simplified Three-Dimensional Limit Equilibrium Analyses of Unsaturated Slope Stability

Geosciences ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 73
Author(s):  
Panagiotis Sitarenios ◽  
Francesca Casini
Keyword(s):  
Analytical Solution ◽  
Slope Stability ◽  
Slope Failure ◽  
Failure Modes ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Three Dimensional ◽  
Stability Limit ◽  
Smooth Transition

This paper presents a three-dimensional slope stability limit equilibrium solution for translational planar failure modes. The proposed solution uses Bishop’s average skeleton stress combined with the Mohr–Coulomb failure criterion to describe soil strength evolution under unsaturated conditions while its formulation ensures a natural and smooth transition from the unsaturated to the saturated regime and vice versa. The proposed analytical solution is evaluated by comparing its predictions with the results of the Ruedlingen slope failure experiment. The comparison suggests that, despite its relative simplicity, the analytical solution can capture the experimentally observed behaviour well and highlights the importance of considering lateral resistance together with a realistic interplay between mechanical parameters (cohesion) and hydraulic (pore water pressure) conditions.

scholarly journals Is Micro X-ray Computer Tomography a Suitable Non-Destructive Method for the Characterisation of Dental Materials?

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1271
Author(s):  
Andreas Koenig ◽  
Leonie Schmohl ◽  
Johannes Scheffler ◽  
Florian Fuchs ◽  
Michaela Schulz-Siegmund ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Computer Tomography ◽  
Mechanical Performance ◽  
Dental Materials ◽  
Three Dimensional ◽  
X Rays ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Multiple Measurements ◽  
High Doses

The aim of the study was to investigate the effect of X-rays used in micro X-ray computer tomography (µXCT) on the mechanical performance and microstructure of a variety of dental materials. Standardised bending beams (2 × 2 × 25 mm3) were forwarded to irradiation with an industrial tomograph. Using three-dimensional datasets, the porosity of the materials was quantified and flexural strength was investigated prior to and after irradiation. The thermal properties of irradiated and unirradiated materials were analysed and compared by means of differential scanning calorimetry (DSC). Single µXCT measurements led to a significant decrease in flexural strength of polycarbonate with acrylnitril-butadien-styrol (PC-ABS). No significant influence in flexural strength was identified for resin-based composites (RBCs), poly(methyl methacrylate) (PMMA), and zinc phosphate cement (HAR) after a single irradiation by measurement. However, DSC results suggest that changes in the microstructure of PMMA are possible with increasing radiation doses (multiple measurements, longer measurements, higher output power from the X-ray tube). In summary, it must be assumed that X-ray radiation during µXCT measurement at high doses can lead to changes in the structure and properties of certain polymers.

scholarly journals Investigations of polyethylene of raised temperature resistance service performance using autoclave test under sour medium conditions

e-Polymers ◽  
2021 ◽  
Vol 21 (1) ◽  
pp. 346-354
Author(s):  
Guoquan Qi ◽  
Hongxia Yan ◽  
Dongtao Qi ◽  
Houbu Li ◽  
Lushi Kong ◽  
...  
Keyword(s):  
Oil And Gas ◽  
Mechanical Performance ◽  
Three Dimensional ◽  
Service Performance ◽  
Degree Of Branching ◽  
Temperature Resistance ◽  
Temperature Conditions ◽  
Dimensional Network ◽  
Gas Medium ◽  
Better Than

Abstract The chapter deals with the performance evaluation of the polyethylene of raised temperature resistance (PE-RT) and polyethylene (PE) using autoclave test under sour oil and gas medium conditions. The analyses of performance changes showed that PE-RT has good media resistance at 60°C. As the temperature increases, its mechanical properties decrease, accompanied by an increase in weight. Comparative analyses showed that no matter what temperature conditions are, PE-RT media resistance is better than PE80. The better media resistance of PE-RT depends on its higher degree of branching. Short branches are distributed between the crystals to form a connection between the crystals, thereby improving its heat resistance and stress under high-temperature conditions. PE-RT forms an excellent three-dimensional network structure through copolymerization, ensuring that it has better media resistance than PE80. However, the mechanical performance will be attenuated due to the high service temperature.

scholarly journals Effect of Crystallographic Orientation and Grain Boundaries on Martensitic Transformation and Superelastic Response of Oligocrystalline Fe–Mn–Al–Ni Shape Memory Alloys

2021 ◽  
Author(s):  
A. Bauer ◽  
M. Vollmer ◽  
T. Niendorf
Keyword(s):  
Martensitic Transformation ◽  
Grain Boundary ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Grain Boundaries ◽  
Tensile Tests ◽  
Image Correlation ◽  
Stress Concentrations ◽  
Grain Orientations ◽  
High Degree

AbstractIn situ tensile tests employing digital image correlation were conducted to study the martensitic transformation of oligocrystalline Fe–Mn–Al–Ni shape memory alloys in depth. The influence of different grain orientations, i.e., near-〈001〉 and near-〈101〉, as well as the influence of different grain boundary misorientations are in focus of the present work. The results reveal that the reversibility of the martensite strongly depends on the type of martensitic evolving, i.e., twinned or detwinned. Furthermore, it is shown that grain boundaries lead to stress concentrations and, thus, to formation of unfavored martensite variants. Moreover, some martensite plates seem to penetrate the grain boundaries resulting in a high degree of irreversibility in this area. However, after a stable microstructural configuration is established in direct vicinity of the grain boundary, the transformation begins inside the neighboring grains eventually leading to a sequential transformation of all grains involved.

scholarly journals Full-Field Operational Modal Analysis of an Aircraft Composite Panel from the Dynamic Response in Multi-Impact Test

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1602
Author(s):  
Ángel Molina-Viedma ◽  
Elías López-Alba ◽  
Luis Felipe-Sesé ◽  
Francisco Díaz
Keyword(s):  
Modal Analysis ◽  
Energy Absorption ◽  
High Speed ◽  
Operational Modal Analysis ◽  
Modal Identification ◽  
Image Correlation ◽  
Composite Panel ◽  
Impact Excitation ◽  
Full Field ◽  
The Impact

Experimental characterization and validation of skin components in aircraft entails multiple evaluations (structural, aerodynamic, acoustic, etc.) and expensive campaigns. They require different rigs and equipment to perform the necessary tests. Two of the main dynamic characterizations include the energy absorption under impact forcing and the identification of modal parameters through the vibration response under any broadband excitation, which also includes impacts. This work exploits the response of a stiffened aircraft composite panel submitted to a multi-impact excitation, which is intended for impact and energy absorption analysis. Based on the high stiffness of composite materials, the study worked under the assumption that the global response to the multi-impact excitation is linear with small strains, neglecting the nonlinear behavior produced by local damage generation. Then, modal identification could be performed. The vibration after the impact was measured by high-speed 3D digital image correlation and employed for full-field operational modal analysis. Multiple modes were characterized in a wide spectrum, exploiting the advantages of the full-field noninvasive techniques. These results described a consistent modal behavior of the panel along with good indicators of mode separation given by the auto modal assurance criterion (Auto-MAC). Hence, it illustrates the possibility of performing these dynamic characterizations in a single test, offering additional information while reducing time and investment during the validation of these structures.

Numerical and experimental investigation for enhancing the energy absorption capacity of the novel three-dimensional printed sandwich structures

2021 ◽  
pp. 146442072199749
Author(s):  
H Geramizadeh ◽  
S Dariushi ◽  
S Jedari Salami
Keyword(s):  
Energy Absorption ◽  
Sandwich Structures ◽  
Three Dimensional ◽  
Absorption Capacity ◽  
The Novel ◽  
Energy Absorption Capacity ◽  
Fused Deposition ◽  
Honeycomb Sandwich ◽  
Out Of Plane ◽  
Vertical Walls

The current study focuses on designing the optimal three-dimensional printed sandwich structures. The main goal is to improve the energy absorption capacity of the out-of-plane honeycomb sandwich beam. The novel Beta VI and Alpha VI were designed in order to achieve this aim. In the Beta VI, the connecting curves (splines) were used instead of the four diagonal walls, while the two vertical walls remained unchanged. The Alpha VI is a step forward on the Beta VI, which was promoted by filleting all angles among the vertical walls, created arcs, and face sheets. The two offered sandwich structures have not hitherto been provided in the literature. All models were designed and simulated by the CATIA and ABAQUS, respectively. The three-dimensional printer fabricated the samples by fused deposition modeling technique. The material properties were determined under tensile, compression, and three-point bending tests. The results are carried out by two methods based on experimental tests and finite element analyses that confirmed each other. The achievements provide novel insights into the determination of the adequate number of unit cells and demonstrate the energy absorption capacity of the Beta VI and Alpha VI are 23.7% and 53.9%, respectively, higher than the out-of-plane honeycomb sandwich structures.

scholarly journals Evaluation of Energy Absorption Capabilities of Polyethylene Foam under Impact Deformation

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3613
Author(s):  
Baohui Yang ◽  
Yangjie Zuo ◽  
Zhengping Chang
Keyword(s):  
Energy Absorption ◽  
Failure Modes ◽  
High Strain ◽  
Early Stage ◽  
High Energy ◽  
Test Method ◽  
Test Theory ◽  
Strain Rates ◽  
Impact Properties ◽  
The Impact

Foams are widely used in protective applications requiring high energy absorption under impact, and evaluating impact properties of foams is vital. Therefore, a novel test method based on a shock tube was developed to investigate the impact properties of closed-cell polyethylene (PE) foams at strain rates over 6000 s−1, and the test theory is presented. Based on the test method, the failure progress and final failure modes of PE foams are discussed. Moreover, energy absorption capabilities of PE foams were assessed under both quasi-static and high strain rate loading conditions. The results showed that the foam exhibited a nonuniform deformation along the specimen length under high strain rates. The energy absorption rate of PE foam increased with the increasing of strain rates. The specimen energy absorption varied linearly in the early stage and then increased rapidly, corresponding to a uniform compression process. However, in the shock wave deformation process, the energy absorption capacity of the foam maintained a good stability and exhibited the best energy absorption state when the speed was higher than 26 m/s. This stable energy absorption state disappeared until the speed was lower than 1.3 m/s. The loading speed exhibited an obvious influence on energy density.

Sign in / Sign up

Export Citation Format

Share Document