scholarly journals An elastocapillary model of wood-fibre collapse

2015 ◽  
Vol 471 (2179) ◽  
pp. 20150184 ◽  
Author(s):  
Amir Akbari ◽  
Reghan J. Hill ◽  
Theo G. M. van de Ven
Keyword(s):  
Contact Angle ◽  
Aspect Ratio ◽  
Elastic Membrane ◽  
Saturation Point ◽  
Capillary Surfaces ◽  
Hole Radius ◽  
Wide Range ◽  
Structural Failures ◽  
Membrane Stretching ◽  
Rigid Walls

An elastocapillary model for drying-induced collapse is proposed. We consider a circular elastic membrane with a hole at the centre that is deformed by the capillary pressure of simply and doubly connected menisci. The membrane overlays a cylindrical cavity with rigid walls, trapping a prescribed volume of water. This geometry may be suitable for studying structural failures and stiction in micro-electromechanical systems during wet etching, where capillary surfaces experience catastrophic transitions. The dry state is determined using the dihedral-angle and volume-turning-point stability criteria. Open and collapsed conformations are predicted from the scaled hole radius, cavity aspect ratio, meniscus contact angle with the membrane and cavity walls, and an elastocapillary number measuring the membrane stretching rigidity relative to the water surface tension. For a given scaled hole radius and cavity aspect ratio, there is a critical elastocapillary number above which the system does not collapse upon drying. The critical elastocapillary number is weakly influenced by the contact angle over a wide range of the scaled hole radius, thus indicating a limitation of surface hydrophobization for controlling the dry-state conformation. The model is applied to the drying of wood fibres above the fibre saturation point, determining the conditions leading to collapse.

Wetting of glass surface using natural surfactants

2020 ◽  
Vol 12 ◽  
Author(s):  
Nihar Ranjan Biswal
Keyword(s):  
Contact Angle ◽  
Glass Surface ◽  
Pure Water ◽  
Amyl Alcohol ◽  
Synthetic Surfactant ◽  
Wide Range ◽  
Different Types ◽  
Natural Surfactants ◽  
Triton X ◽  
Solid Liquid

Background: Surfactant adsorption at the interfaces (solid–liquid, liquid–air, or liquid–liquid) is receiving considerable attention from a long time due to its wide range of practical applications. Objective: Specifically wettability of solid surface by liquids is mainly measured by contact angle and has many practical importances where solid–liquid systems are used. Adsorption of surfactants plays an important role in the wetting process. The wetting behaviours of three plant-based natural surfactants (Reetha, Shikakai, and Acacia) on the glass surface are compared with one widely used nonionic synthetic surfactant (Triton X-100) and reported in this study. Methods: The dynamic contact angle study of three different types of plant surfactants (Reetha, Shikakai and Acacia) and one synthetic surfactant (Triton X 100) on the glass surface has been carried out. The effect of two different types of alcohols such as Methanol and amyl alcohol on wettability of shikakai, as it shows little higher value of contact angle on glass surface has been measured. Results: The contact angle measurements show that there is an increase in contact angle from 47° (pure water) to 67.72°, 65.57°, 68.84°, and 68.79° for Reetha, Acacia, Shikakai, and Triton X-100 respectively with the increase in surfactant concentration and remain constant at CMC. The change in contact angle of Shikakai-Amyl alcohol mixtures are slightly different than that of methanol-Shikakai mixture, mostly there is a gradual increase in contact angle with the increasing in alcohol concentration. Conclusion: There is no linear relationship between cos θ and inverse of surface tension. There was a linear increase in surface free energy results with increase in concentration as more surfactant molecules were adsorbing at the interface enhancing an increase in contact angle.

scholarly journals High-resolution particle separation by inertial focusing in high aspect ratio curved microfluidics

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Javier Cruz ◽  
Klas Hjort
Keyword(s):  
High Resolution ◽  
Aspect Ratio ◽  
High Aspect Ratio ◽  
Biological Fluids ◽  
Essential Feature ◽  
Particle Separation ◽  
Size Difference ◽  
Inertial Focusing ◽  
Complex Samples ◽  
Wide Range

AbstractThe ability to focus, separate and concentrate specific targets in a fluid is essential for the analysis of complex samples such as biological fluids, where a myriad of different particles may be present. Inertial focusing is a very promising technology for such tasks, and specially a recently presented variant, inertial focusing in High Aspect Ratio Curved systems (HARC systems), where the systems are easily engineered and focus the targets together in a stable position over a wide range of particle sizes and flow rates. However, although convenient for laser interrogation and concentration, by focusing all particles together, HARC systems lose an essential feature of inertial focusing: the possibility of particle separation by size. Within this work, we report that HARC systems not only do have the capacity to separate particles but can do so with extremely high resolution, which we demonstrate for particles with a size difference down to 80 nm. In addition to the concept for particle separation, a model considering the main flow, the secondary flow and a simplified expression for the lift force in HARC microchannels was developed and proven accurate for the prediction of the performance of the systems. The concept was also demonstrated experimentally with three different sub-micron particles (0.79, 0.92 and 1.0 µm in diameter) in silicon-glass microchannels, where the resolution in the separation could be modulated by the radius of the channel. With the capacity to focus sub-micron particles and to separate them with high resolution, we believe that inertial focusing in HARC systems is a technology with the potential to facilitate the analysis of complex fluid samples containing bioparticles like bacteria, viruses or eukaryotic organelles.

Heat transfer characteristics of nanofluids from a sinusoidal corrugated cylinder placed in a square cavity

2021 ◽  
pp. 095440622110272
Author(s):  
Salaika Parvin ◽  
Nepal Chandra Roy ◽  
Litan Kumar Saha ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Average Nusselt Number ◽  
Numerical Study ◽  
Heat Transfer Characteristics ◽  
Number Range ◽  
Transfer Characteristics ◽  
Wide Range

A numerical study is performed to investigate nanofluids' flow field and heat transfer characteristics between the domain bounded by a square and a wavy cylinder. The left and right walls of the cavity are at constant low temperature while its other adjacent walls are insulated. The convective phenomena take place due to the higher temperature of the inner corrugated surface. Super elliptic functions are used to transform the governing equations of the classical rectangular enclosure into a system of equations valid for concentric cylinders. The resulting equations are solved iteratively with the implicit finite difference method. Parametric results are presented in terms of streamlines, isotherms, local and average Nusselt numbers for a wide range of scaled parameters such as nanoparticles concentration, Rayleigh number, and aspect ratio. Several correlations have been deduced at the inner and outer surface of the cylinders for the average Nusselt number, which gives a good agreement when compared against the numerical results. The strength of the streamlines increases significantly due to an increase in the aspect ratio of the inner cylinder and the Rayleigh number. As the concentration of nanoparticles increases, the average Nusselt number at the internal and external cylinders becomes stronger. In addition, the average Nusselt number for the entire Rayleigh number range gets enhanced when plotted against the volume fraction of the nanofluid.

scholarly journals Is contact angle a cause or an effect? – A cautionary tale

2020 ◽  
Vol 146 ◽  
pp. 03004
Author(s):  
Douglas Ruth
Keyword(s):  
Contact Angle ◽  
Solid Surface ◽  
Contact Angles ◽  
Two Dimensions ◽  
Experimental Results ◽  
Flow In Porous Media ◽  
Two Dimensional ◽  
Wide Range ◽  
Fluid Drop ◽  
Surrounding Fluid

The most influential parameter on the behavior of two-component flow in porous media is “wettability”. When wettability is being characterized, the most frequently used parameter is the “contact angle”. When a fluid-drop is placed on a solid surface, in the presence of a second, surrounding fluid, the fluid-fluid surface contacts the solid-surface at an angle that is typically measured through the fluid-drop. If this angle is less than 90°, the fluid in the drop is said to “wet” the surface. If this angle is greater than 90°, the surrounding fluid is said to “wet” the surface. This definition is universally accepted and appears to be scientifically justifiable, at least for a static situation where the solid surface is horizontal. Recently, this concept has been extended to characterize wettability in non-static situations using high-resolution, two-dimensional digital images of multi-component systems. Using simple thought experiments and published experimental results, many of them decades old, it will be demonstrated that contact angles are not primary parameters – their values depend on many other parameters. Using these arguments, it will be demonstrated that contact angles are not the cause of wettability behavior but the effect of wettability behavior and other parameters. The result of this is that the contact angle cannot be used as a primary indicator of wettability except in very restricted situations. Furthermore, it will be demonstrated that even for the simple case of a capillary interface in a vertical tube, attempting to use simply a two-dimensional image to determine the contact angle can result in a wide range of measured values. This observation is consistent with some published experimental results. It follows that contact angles measured in two-dimensions cannot be trusted to provide accurate values and these values should not be used to characterize the wettability of the system.

scholarly journals Strength Analysis of Alternative Airframe Layouts of Regional Aircraft on the Basis of Automated Parametrical Models

Aerospace ◽  
2021 ◽  
Vol 8 (3) ◽  
pp. 80
Author(s):  
Dmitry V. Vedernikov ◽  
Alexander N. Shanygin ◽  
Yury S. Mirgorodsky ◽  
Mikhail D. Levchenkov
Keyword(s):  
Aspect Ratio ◽  
High Aspect Ratio ◽  
High Performance ◽  
Strength Analysis ◽  
Labor Input ◽  
Aerodynamic Loading ◽  
Aspect Ratios ◽  
Wide Range ◽  
Parametrical Design

This publication presents the results of complex parametrical strength investigations of typical wings for regional aircrafts obtained by means of the new version of the four-level algorithm (FLA) with the modified module responsible for the analysis of aerodynamic loading. This version of FLA, as well as a base one, is focused on significant decreasing time and labor input of a complex strength analysis of airframes by using simultaneously different principles of decomposition. The base version includes four-level decomposition of airframe and decomposition of strength tasks. The new one realizes additional decomposition of alternative variants of load cases during the process of determination of critical load cases. Such an algorithm is very suitable for strength analysis and designing airframes of regional aircrafts having a wide range of aerodynamic concepts. Results of validation of the new version of FLA for a high-aspect-ratio wing obtained in this work confirmed high performance of the algorithm in decreasing time and labor input of strength analysis of airframes at the preliminary stages of designing. During parametrical design investigation, some interesting results for strut-braced wings having high aspect ratios were obtained.

scholarly journals Self-ordered nanospike porous alumina fabricated under a new regime by an anodizing process in alkaline media

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Mana Iwai ◽  
Tatsuya Kikuchi ◽  
Ryosuke O. Suzuki
Keyword(s):  
Aspect Ratio ◽  
High Aspect Ratio ◽  
Porous Alumina ◽  
Three Dimensional ◽  
Alkaline Media ◽  
Alkaline Electrolyte ◽  
Subsequent Formation ◽  
Interpore Distance ◽  
Wide Range ◽  
Ordered Porous

AbstractHigh-aspect ratio ordered nanomaterial arrays exhibit several unique physicochemical and optical properties. Porous anodic aluminum oxide (AAO) is one of the most typical ordered porous structures and can be easily fabricated by applying an electrochemical anodizing process to Al. However, the dimensional and structural controllability of conventional porous AAOs is limited to a narrow range because there are only a few electrolytes that work in this process. Here, we provide a novel anodizing method using an alkaline electrolyte, sodium tetraborate (Na2B4O7), for the fabrication of a high-aspect ratio, self-ordered nanospike porous AAO structure. This self-ordered porous AAO structure possesses a wide range of the interpore distance under a new anodizing regime, and highly ordered porous AAO structures can be fabricated using pre-nanotexturing of Al. The vertical pore walls of porous AAOs have unique nanospikes measuring several tens of nanometers in periodicity, and we demonstrate that AAO can be used as a template for the fabrication of nanomaterials with a large surface area. We also reveal that stable anodizing without the occurrence of oxide burning and the subsequent formation of uniform self-ordered AAO structures can be achieved on complicated three-dimensional substrates.

scholarly journals Influence of Pile Diameter and Aspect Ratio on the Lateral Response of Monopiles in Sand with Different Relative Densties

2021 ◽  
Vol 9 (6) ◽  
pp. 618
Author(s):  
Huan Wang ◽  
Lizhong Wang ◽  
Yi Hong ◽  
Amin Askarinejad ◽  
Ben He ◽  
...  
Keyword(s):  
Aspect Ratio ◽  
Large Diameter ◽  
Pressure Coefficient ◽  
Offshore Wind ◽  
Fe Model ◽  
Soil Pressure ◽  
Pile Diameter ◽  
Centrifuge Tests ◽  
Aspect Ratios ◽  
Wide Range

The large-diameter monopiles are the most preferred foundation used in offshore wind farms. However, the influence of pile diameter and aspect ratio on the lateral bearing behavior of monopiles in sand with different relative densities has not been systematically studied. This study presents a series of well-calibrated finite-element (FE) analyses using an advanced state dependent constitutive model. The FE model was first validated against the centrifuge tests on the large-diameter monopiles. Parametric studies were performed on rigid piles with different diameters (D = 4–10 m) and aspect ratios (L/D = 3–7.5) under a wide range of loading heights (e = 5–100 m) in sands with different relative densities (Dr = 40%, 65%, 80%). The API and PISA p-y models were systematically compared and evaluated against the FE simulation results. The numerical results revealed a rigid rotation failure mechanism of the rigid pile, which is independent of pile diameter and aspect ratio. The computed soil pressure coefficient (K = p/Dσ′v) of different diameter piles at same rotation is a function of z/L (z is depth) rather than z/D. The force–moment diagrams at different deflections were quantified in sands of different relative density. Based on the observed pile–soil interaction mechanism, a simple design model was proposed to calculate the combined capacity of rigid piles.

scholarly journals Facile Fabrication of Multifunctional ZnO Urchins on Surfaces

2018 ◽  
Vol 2 (4) ◽  
pp. 74 ◽  
Author(s):  
Abinash Tripathy ◽  
Patryk Wąsik ◽  
Syama Sreedharan ◽  
Dipankar Nandi ◽  
Oier Bikondoa ◽  
...  
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Surface Density ◽  
Room Temperature ◽  
High Surface ◽  
Secondary Growth ◽  
Water Contact ◽  
Growth Step ◽  
Si Substrates ◽  
Wide Range

Functional ZnO nanostructured surfaces are important in a wide range of applications. Here we report the simple fabrication of ZnO surface structures at near room temperature with morphology resembling that of sea urchins, with densely packed, μm-long, tapered nanoneedles radiating from the urchin center. The ZnO urchin structures were successfully formed on several different substrates with high surface density and coverage, including silicon (Si), glass, polydimethylsiloxane (PDMS), and copper (Cu) sheets, as well as Si seeded with ZnO nanocrystals. Time-resolved SEM revealed growth kinetics of the ZnO nanostructures on Si, capturing the emergence of “infant” urchins at the early growth stage and subsequent progressive increases in the urchin nanoneedle length and density, whilst the spiky nanoneedle morphology was retained throughout the growth. ε-Zn(OH)2 orthorhombic crystals were also observed alongside the urchins. The crystal structures of the nanostructures at different growth times were confirmed by synchrotron X-ray diffraction measurements. On seeded Si substrates, a two-stage growth mechanism was identified, with a primary growth step of vertically aligned ZnO nanoneedle arrays preceding the secondary growth of the urchins atop the nanoneedle array. The antibacterial, anti-reflective, and wetting functionality of the ZnO urchins—with spiky nanoneedles and at high surface density—on Si substrates was demonstrated. First, bacteria colonization was found to be suppressed on the surface after 24 h incubation in gram-negative Escherichia coli (E. coli) culture, in contrast to control substrates (bare Si and Si sputtered with a 20 nm ZnO thin film). Secondly, the ZnO urchin surface, exhibiting superhydrophilic property with a water contact angle ~ 0°, could be rendered superhydrophobic with a simple silanization step, characterized by an apparent water contact angle θ of 159° ± 1.4° and contact angle hysteresis ∆θ < 7°. The dynamic superhydrophobicity of the surface was demonstrated by the bouncing-off of a falling 10 μL water droplet, with a contact time of 15.3 milliseconds (ms), captured using a high-speed camera. Thirdly, it was shown that the presence of dense spiky ZnO nanoneedles and urchins on the seeded Si substrate exhibited a reflectance R < 1% over the wavelength range λ = 200–800 nm. The ZnO urchins with a unique morphology fabricated via a simple route at room temperature, and readily implementable on different substrates, may be further exploited for multifunctional surfaces and product formulations.

Performance Estimation of Axial Flow Turbines

1970 ◽  
Vol 185 (1) ◽  
pp. 407-424 ◽  
Author(s):  
H. R. M. Craig ◽  
H. J. A. Cox
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Gas Turbines ◽  
Three Dimensional ◽  
Axial Flow ◽  
Performance Estimation ◽  
Speed Ratio ◽  
Test Results ◽  
Wide Range ◽  
Relevant Variables

A comprehensive method of estimating the performance of axial flow steam and gas turbines is presented, based on analysis of linear cascade tests on blading, on a number of turbine test results, and on air tests of model casings. The validity of the use of such data is briefly considered. Data are presented to allow performance estimation of actual machines over a wide range of Reynolds number, Mach number, aspect ratio and other relevant variables. The use of the method in connection with three-dimensional methods of flow estimation is considered, and data presented showing encouraging agreement between estimates and available test results. Finally ‘carpets’ are presented showing the trends in efficiencies that are attainable in turbines designed over a wide range of loading, axial velocity/blade speed ratio, Reynolds number and aspect ratio.

Elastohydrodynamic Lubrication of Soft-Layered Solids at Elliptical Contacts: Part 1: Elasticity Analysis

1994 ◽  
Vol 208 (1) ◽  
pp. 31-41 ◽  
Author(s):  
J Q Yao ◽  
D Dowson
Keyword(s):  
Aspect Ratio ◽  
Surface Deformation ◽  
Applied Pressure ◽  
Numerical Procedure ◽  
Elastohydrodynamic Lubrication ◽  
Thin Layers ◽  
Elasticity Analysis ◽  
Synovial Joint ◽  
Wide Range ◽  
Non Linear System

In this two-part paper we consider the elastohydrodynamic lubrication (EHL) of soft-layered solids representing elliptical contacts. The problem has not previously attracted much attention, partly due to the lack of an effective numerical procedure to solve the coupled non-linear system of equations, but it is essential to the proper design of bearings with soft elastomeric liners and the full understanding of synovial joint lubrication. In Part 1, the elasticity analysis for the surface deformation of a low elastic modulus layer on a hard-backing half-space under various forms of normal loadings is considered, by means of both the rigorous Hankel transform method and various simplifications. For layers of compressible materials (v ≤ 0.4), a generalized foundation model described by a second-order differential equation is proposed to represent the relationship between the surface deformation and the applied pressure. The empirical equation developed in this study is valid for a very wide range of the aspect ratio of the contact and provides an alternative way of modelling the elastic deformation without recourse to the often tedious integration in the numerical analysis of the EHL problem. The simplest form (constrained column model) of the equation, where the surface deformation is directly proportional to the local applied pressure, was found to be reasonably accurate for compressible thin layers (the aspect ratio 2b/ht ≥ 5 and Poisson's ratio v ≤ 0.4).

Sign in / Sign up

Export Citation Format

Share Document