High-Performance High Speed IGBT Based Induction Motor Driven By Cycloinverter-Fed with Slit Rotor

2018 ◽  
Author(s):  
Anchal Yadav ◽  
Pratibha Tiwari ◽  
Sarika Kalra
Keyword(s):  
Induction Motor ◽  
High Speed ◽  
High Performance

Novel Discrete Components Based Speed Controller for Induction Motor

2016 ◽  
Vol 7 (4) ◽  
pp. 1075
Author(s):  
Hussain Attia ◽  
Ali Sagafinia
Keyword(s):  
Induction Motor ◽  
Digital Signal Processor ◽  
High Speed ◽  
High Performance ◽  
Low Cost ◽  
Digital Signal ◽  
Speed Control ◽  
Electronic System ◽  
Voltage Controlled Oscillator ◽  
Electronic Design

This paper presents an electronic design based on general purpose discrete components for speed control of a single phase induction motor drive. The MOSFETs inverter switching is controlled using Sampled Sinusoidal Pulse Width Modulation (SPWM) techniques with V/F method based on Voltage Controlled Oscillator (VCO). The load power is also controlled by a novel design to produce a suitable SPWM pulse. The proposed electronic system has ability to control the output frequency with flexible setting of lower limit to less than 1 Hz and to higher frequency limits to 55 Hz. Moreover, the proposed controller able to control the value of load voltage to frequency ratio, which plays a major parameter in the function of IM speed control. Furthermore, the designed system is characterized by easy manufacturing and maintenance, high speed response, low cost, and does not need to program steps as compared to other systems based on Microcontroller and digital signal processor (DSP) units. The complete proposed electronic design is made by the software of NI Multisim version 11.0 and all the internal sub-designs are shown in this paper. Simulation results show the effectiveness of electronic design for a promising of a high performance IM PWM drive.

Vacuum System to Minimize the Specimen Contamination of High-Performance EM

1977 ◽  
Vol 35 ◽  
pp. 68-69
Author(s):  
N. Yoshimura ◽  
K. Shirota ◽  
T. Etoh
Keyword(s):  
Electron Microscope ◽  
High Speed ◽  
High Performance ◽  
High Vacuum ◽  
Vacuum System ◽  
Pump System ◽  
Pumping System ◽  
Diffusion Pump ◽  
Almost All ◽  
Cascade Type

One of the most important requirements for a high-performance EM, especially an analytical EM using a fine beam probe, is to prevent specimen contamination by providing a clean high vacuum in the vicinity of the specimen. However, in almost all commercial EMs, the pressure in the vicinity of the specimen under observation is usually more than ten times higher than the pressure measured at the punping line. The EM column inevitably requires the use of greased Viton O-rings for fine movement, and specimens and films need to be exchanged frequently and several attachments may also be exchanged. For these reasons, a high speed pumping system, as well as a clean vacuum system, is now required. A newly developed electron microscope, the JEM-100CX features clean high vacuum in the vicinity of the specimen, realized by the use of a CASCADE type diffusion pump system which has been essentially improved over its predeces- sorD employed on the JEM-100C.

PHAX-SCAN: Functional integration of a Scanning Electron Microscope and an energy-dispersive x-ray analyser

1989 ◽  
Vol 47 ◽  
pp. 56-57
Author(s):  
Marc H. Peeters ◽  
Max T. Otten
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
High Speed ◽  
High Performance ◽  
Functional Integration ◽  
Energy Dispersive ◽  
X Rays ◽  
X Ray ◽  
High Speed Analysis ◽  
Scanning Electron

Over the past decades, the combination of energy-dispersive analysis of X-rays and scanning electron microscopy has proved to be a powerful tool for fast and reliable elemental characterization of a large variety of specimens. The technique has evolved rapidly from a purely qualitative characterization method to a reliable quantitative way of analysis. In the last 5 years, an increasing need for automation is observed, whereby energy-dispersive analysers control the beam and stage movement of the scanning electron microscope in order to collect digital X-ray images and perform unattended point analysis over multiple locations.The Philips High-speed Analysis of X-rays system (PHAX-Scan) makes use of the high performance dual-processor structure of the EDAX PV9900 analyser and the databus structure of the Philips series 500 scanning electron microscope to provide a highly automated, user-friendly and extremely fast microanalysis system. The software that runs on the hardware described above was specifically designed to provide the ultimate attainable speed on the system.

The bright future of digital imaging in scanning electron microscopy

1993 ◽  
Vol 51 ◽  
pp. 768-769
Author(s):  
M. T. Postek ◽  
A. E. Vladar
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Digital Imaging ◽  
High Speed ◽  
High Performance ◽  
Mass Storage ◽  
Analog To Digital ◽  
Central Processing ◽  
Digital Imaging Technology ◽  
Scanning Electron

One of the major advancements applied to scanning electron microscopy (SEM) during the past 10 years has been the development and application of digital imaging technology. Advancements in technology, notably the availability of less expensive, high-density memory chips and the development of high speed analog-to-digital converters, mass storage and high performance central processing units have fostered this revolution. Today, most modern SEM instruments have digital electronics as a standard feature. These instruments, generally have 8 bit or 256 gray levels with, at least, 512 × 512 pixel density operating at TV rate. In addition, current slow-scan commercial frame-grabber cards, directly applicable to the SEM, can have upwards of 12-14 bit lateral resolution permitting image acquisition at 4096 × 4096 resolution or greater. The two major categories of SEM systems to which digital technology have been applied are:In the analog SEM system the scan generator is normally operated in an analog manner and the image is displayed in an analog or "slow scan" mode.

High-Performance V/f Control of Induction Motor and Its Stability

2012 ◽  
Vol 132 (9) ◽  
pp. 938-939
Author(s):  
Mineo Tsuji ◽  
Xiaodan Zhao ◽  
Sin-ichi Hamasaki
Keyword(s):  
Induction Motor ◽  
High Performance

A High Performance of Induction Motor Drive System

2020 ◽  
Vol 13 (8) ◽  
pp. 1129-1134
Author(s):  
Cuifeng Shen ◽  
Hanhua Yang
Keyword(s):  
Induction Motor ◽  
High Performance ◽  
Fuzzy Controller ◽  
Drive System ◽  
Motor Drive ◽  
Deterministic System ◽  
Induction Motor Drive ◽  
Paper Making ◽  
Drive Control ◽  
Motor Drive System

Background: A multi-motor synchronous drive control system is widely used in many fields, such as electric vehicle drive, paper making, and printing. Methods: On the basis of the optimized structure of ADRC, a fuzzy first-order active disturbance rejection controller was developed. Double channels compensation of extended state observer was employed to estimate and compensate the total disturbances, and an approximate linearization and deterministic system was obtained. As the parameters of ADRC are adjusted online by a fuzzy controller, the performance of the controller is effectively improved. Results: Based on the SIMATIC S7-300 induction motor control experimental platform, the performances of anti-interference and tracking performance are tested. Conclusion: The actual experimental results indicated that compared with PID control, induction motor drive system controlled by fuzzy ADRC has higher dynamic and static status and following performances and stronger anti-interference abilities.

Performance Analysis of Various Multipliers Using 8T-full Adder with 180nm Technology

2020 ◽  
Vol 13 (6) ◽  
pp. 864-870
Author(s):  
Sai Venkatramana Prasada G.S ◽  
G. Seshikala ◽  
S. Niranjana
Keyword(s):  
Low Power ◽  
Power Dissipation ◽  
High Speed ◽  
High Performance ◽  
Full Adder ◽  
Fundamental Operation ◽  
Wallace Tree ◽  
Power Delay Product ◽  
The Comparative Study ◽  
Wallace Tree Multiplier

Background: This paper presents the comparative study of power dissipation, delay and power delay product (PDP) of different full adders and multiplier designs. Methods: Full adder is the fundamental operation for any processors, DSP architectures and VLSI systems. Here ten different full adder structures were analyzed for their best performance using a Mentor Graphics tool with 180nm technology. Results: From the analysis result high performance full adder is extracted for further higher level designs. 8T full adder exhibits high speed, low power delay and low power delay product and hence it is considered to construct four different multiplier designs, such as Array multiplier, Baugh Wooley multiplier, Braun multiplier and Wallace Tree multiplier. These different structures of multipliers were designed using 8T full adder and simulated using Mentor Graphics tool in a constant W/L aspect ratio. Conclusion: From the analysis, it is concluded that Wallace Tree multiplier is the high speed multiplier but dissipates comparatively high power. Baugh Wooley multiplier dissipates less power but exhibits more time delay and low PDP.

scholarly journals Ultracompact and low-power-consumption silicon thermo-optic switch for high-speed data

Nanophotonics ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 937-945
Author(s):  
Ruihuan Zhang ◽  
Yu He ◽  
Yong Zhang ◽  
Shaohua An ◽  
Qingming Zhu ◽  
...  
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
High Performance ◽  
Pulse Amplitude ◽  
Telecommunication Networks ◽  
Low Power Consumption ◽  
Power Efficient ◽  
High Speed Data ◽  
On Chip

AbstractUltracompact and low-power-consumption optical switches are desired for high-performance telecommunication networks and data centers. Here, we demonstrate an on-chip power-efficient 2 × 2 thermo-optic switch unit by using a suspended photonic crystal nanobeam structure. A submilliwatt switching power of 0.15 mW is obtained with a tuning efficiency of 7.71 nm/mW in a compact footprint of 60 μm × 16 μm. The bandwidth of the switch is properly designed for a four-level pulse amplitude modulation signal with a 124 Gb/s raw data rate. To the best of our knowledge, the proposed switch is the most power-efficient resonator-based thermo-optic switch unit with the highest tuning efficiency and data ever reported.

scholarly journals High-Speed 3D Printing of High-Performance Thermosetting Polymers via Two-Stage Curing

2018 ◽  
Vol 39 (7) ◽  
pp. 1700809 ◽  
Author(s):  
Xiao Kuang ◽  
Zeang Zhao ◽  
Kaijuan Chen ◽  
Daining Fang ◽  
Guozheng Kang ◽  
...  
Keyword(s):  
3D Printing ◽  
High Speed ◽  
High Performance ◽  
Two Stage ◽  
Thermosetting Polymers
Sign in / Sign up

Export Citation Format

Share Document