Performance Testing on Transonic Rotors

2010 ◽  
Vol 132 (08) ◽  
pp. 52-53
Author(s):  
Anthony J. Gannon ◽  
Garth V. Hobson
Keyword(s):  
Mach Number ◽  
Power Consumption ◽  
Flow Rate ◽  
Atmospheric Pressure ◽  
High Speed ◽  
Performance Testing ◽  
Test Machine ◽  
Naval Postgraduate School ◽  
Scale Down ◽  
Limit Power

This article discusses the performance testing of transonic rotors at the Turbopropulsion Laboratory at the Naval Postgraduate School. The Mach number is one of the most important parameters in the case of high-speed compressors. In order to limit power consumption in a test machine, the simplest change is to scale down the machine. A second concept to reduce the power consumption of the machine once it has been scaled down is to throttle the flow before the rotor rather than after it. As a high-speed rotor compresses the incoming air by around 1.4–1.6 times, the air leaving it is appreciably denser than that coming in. If one throttles upstream of the rotor, the exhaust air leaves the machine at atmospheric pressure, which means that the incoming air is below atmospheric pressure. With upstream throttling, care has to be taken to provide long enough ducting ahead of the test compressor to present as uniform as possible flow after the flow rate measuring nozzle.

Experimental Investigation of Spray Dynamics Under Jet Engine Augmentor-Like Conditions

2006 ◽  
Author(s):  
Javier N. Johnson ◽  
Eugene Lubarsky ◽  
Ben T. Zinn
Keyword(s):  
Experimental Investigation ◽  
Mach Number ◽  
Atmospheric Pressure ◽  
High Speed ◽  
Cross Flow ◽  
Short Exposure ◽  
Jet Engine ◽  
Breakup Mechanism ◽  
Jet Breakup ◽  
Fuel Jet

This paper describes an experimental investigation of fuel spray jet breakup mechanisms when it is injected across the high temperature air flow in low and high pressure jet engine augmentor-like conditions. Phase Doppler particle analyzer data and short exposure pulsed shadow graph images were taken of fuel jet injected into an air cross flow with liquid to air momentum ratios ranging from 5 to 180. Measured droplet diameters taken at atmospheric pressure and a flow Mach number of ∼0.15 show a progressive breakup of the droplets, gradually decreasing in size from 250μm to 150μm and finally to 25 μm as the spray moves downstream. The progressive breakup of droplets follows the classical Rayleigh-Helmholtz breakup mechanism. At higher pressure and Mach number tests, the fuel jet undergoes a different breakup process; i.e., the fuel jet breaks up instantaneously into a monodispurse spray of smaller droplets near the injector. High speed images of this process suggest that an aerodynamic breakup mechanism dominates this atomization process near the injector. In summary, the results of this study show the fuel jet breakup mechanism in augmentors varies significantly over the flight envelope.

Cyclone Bomb hits Southern Brazil in 2020

2020 ◽  
Vol 3 (3) ◽  
Author(s):  
Ricardo Gobato ◽  
Alireza Heidari
Keyword(s):  
High Pressure ◽  
Atmospheric Pressure ◽  
High Speed ◽  
Satellite Images ◽  
The State ◽  
Southern Brazil ◽  
Santa Catarina ◽  
High Area ◽  
South Of Brazil ◽  
Rapid Drop

An “explosive extratropical cyclone” is an atmospheric phenomenon that occurs when there is a very rapid drop in central atmospheric pressure. This phenomenon, with its characteristic of rapidly lowering the pressure in its interior, generates very intense winds and for this reason it is called explosive cyclone, bomb cyclone. With gusts recorded of 116 km/h, atmospheric phenomenon – “cyclone bomb” (CB) hit southern Brazil on June 30, the beginning of winter 2020, causing destruction in its influence over. One of the cities most affected was Chapecó, west of the state of Santa Catarina. The satellite images show that the CB generated a low pressure (976 mbar) inside it, generating two atmospheric currents that moved at high speed. In a northwest-southeast direction, Bolivia and Paraguay, crossing the states of Parana and Santa Catarina, and this draft that hit the south of Brazil, which caused the destruction of the affected states.  Another moving to Argentina, southwest-northeast direction, due to high area of high pressure (1022 mbar). Both enhanced the phenomenon.

Design and Implementation of an Efficient Parallel LFSR Architecture for Wireless Communication Systems

2019 ◽  
Vol 14 ◽  
Author(s):  
A. Suresh Babu ◽  
B. Anand
Keyword(s):  
Wireless Communication ◽  
Power Consumption ◽  
Low Power ◽  
Communication Systems ◽  
High Speed ◽  
Design Tool ◽  
Shift Register ◽  
Linear Feedback ◽  
Wireless Communication Systems ◽  
Coverage Area

: A Linear Feedback Shift Register (LFSR) considers a linear function typically an XOR operation of the previous state as an input to the current state. This paper describes in detail the recent Wireless Communication Systems (WCS) and techniques related to LFSR. Cryptographic methods and reconfigurable computing are two different applications used in the proposed shift register with improved speed and decreased power consumption. Comparing with the existing individual applications, the proposed shift register obtained >15 to <=45% of decreased power consumption with 30% of reduced coverage area. Hence this proposed low power high speed LFSR design suits for various low power high speed applications, for example wireless communication. The entire design architecture is simulated and verified in VHDL language. To synthesis a standard cell library of 0.7um CMOS is used. A custom design tool has been developed for measuring the power. From the results, it is obtained that the cryptographic efficiency is improved regarding time and complexity comparing with the existing algorithms. Hence, the proposed LFSR architecture can be used for any wireless applications due to parallel processing, multiple access and cryptographic methods.

Low Power and High Speed Sequential Circuits Test Architecture

2019 ◽  
Vol 12 ◽  
Author(s):  
Ahmed K. Jameil ◽  
Yasir Amer Abbas ◽  
Saad Al-Azawi
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Test Generation ◽  
High Speed ◽  
Fir Filter ◽  
Sequential Circuits ◽  
Fir Filters ◽  
Design Verification ◽  
Sequential Circuit ◽  
Generation Algorithm

Background: The designed circuits are tested for faults detection in fabrication to determine which devices are defective. The design verification is performed to ensure that the circuit performs the required functions after manufacturing. Design verification is regarded as a test form in both sequential and combinational circuits. The analysis of sequential circuits test is more difficult than in the combinational circuit test. However, algorithms can be used to test any type of sequential circuit regardless of its composition. An important sequential circuit is the finite impulse response (FIR) filters that are widely used in digital signal processing applications. Objective: This paper presented a new design under test (DUT) algorithm for 4-and 8-tap FIR filters. Also, the FIR filter and the proposed DUT algorithm is implemented using field programmable gate arrays (FPGA). Method: The proposed test generation algorithm is implemented in VHDL using Xilinx ISE V14.5 design suite and verified by simulation. The test generation algorithm used FIR filtering redundant faults to obtain a set of target faults for DUT. The fault simulation is used in DUT to assess the benefit of test pattern in fault coverage. Results: The proposed technique provides average reductions of 20 % and 38.8 % in time delay with 57.39 % and 75 % reductions in power consumption and 28.89 % and 28.89 % slices reductions for 4- and 8-tap FIR filter, respectively compared to similar techniques. Conclusions: The results of implementation proved that a high speed and low power consumption design can be achieved. Further, the speed of the proposed architecture is faster than that of existing techniques.

scholarly journals Ultracompact and low-power-consumption silicon thermo-optic switch for high-speed data

Nanophotonics ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 937-945
Author(s):  
Ruihuan Zhang ◽  
Yu He ◽  
Yong Zhang ◽  
Shaohua An ◽  
Qingming Zhu ◽  
...  
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
High Performance ◽  
Pulse Amplitude ◽  
Telecommunication Networks ◽  
Low Power Consumption ◽  
Power Efficient ◽  
High Speed Data ◽  
On Chip

AbstractUltracompact and low-power-consumption optical switches are desired for high-performance telecommunication networks and data centers. Here, we demonstrate an on-chip power-efficient 2 × 2 thermo-optic switch unit by using a suspended photonic crystal nanobeam structure. A submilliwatt switching power of 0.15 mW is obtained with a tuning efficiency of 7.71 nm/mW in a compact footprint of 60 μm × 16 μm. The bandwidth of the switch is properly designed for a four-level pulse amplitude modulation signal with a 124 Gb/s raw data rate. To the best of our knowledge, the proposed switch is the most power-efficient resonator-based thermo-optic switch unit with the highest tuning efficiency and data ever reported.

scholarly journals CFD Simulation of a Hyperloop Capsule Inside a Low-Pressure Environment Using an Aerodynamic Compressor as Propulsion and Drag Reduction Method

2021 ◽  
Vol 11 (9) ◽  
pp. 3934
Author(s):  
Federico Lluesma-Rodríguez ◽  
Temoatzin González ◽  
Sergio Hoyas
Keyword(s):  
Shock Waves ◽  
Power Consumption ◽  
High Speed ◽  
Cfd Simulation ◽  
Aerodynamic Drag ◽  
Flow Behavior ◽  
Critical Conditions ◽  
Vehicle Speed ◽  
Blockage Ratio ◽  
The Cost

One of the most restrictive conditions in ground transportation at high speeds is aerodynamic drag. This is even more problematic when running inside a tunnel, where compressible phenomena such as wave propagation, shock waves, or flow blocking can happen. Considering Evacuated-Tube Trains (ETTs) or hyperloops, these effects appear during the whole route, as they always operate in a closed environment. Then, one of the concerns is the size of the tunnel, as it directly affects the cost of the infrastructure. When the tube size decreases with a constant section of the vehicle, the power consumption increases exponentially, as the Kantrowitz limit is surpassed. This can be mitigated when adding a compressor to the vehicle as a means of propulsion. The turbomachinery increases the pressure of part of the air faced by the vehicle, thus delaying the critical conditions on surrounding flow. With tunnels using a blockage ratio of 0.5 or higher, the reported reduction in the power consumption is 70%. Additionally, the induced pressure in front of the capsule became a negligible effect. The analysis of the flow shows that the compressor can remove the shock waves downstream and thus allows operation above the Kantrowitz limit. Actually, for a vehicle speed of 700 km/h, the case without a compressor reaches critical conditions at a blockage ratio of 0.18, which is a tunnel even smaller than those used for High-Speed Rails (0.23). When aerodynamic propulsion is used, sonic Mach numbers are reached above a blockage ratio of 0.5. A direct effect is that cases with turbomachinery can operate in tunnels with blockage ratios even 2.8 times higher than the non-compressor cases, enabling a considerable reduction in the size of the tunnel without affecting the performance. This work, after conducting bibliographic research, presents the geometry, mesh, and setup. Later, results for the flow without compressor are shown. Finally, it is discussed how the addition of the compressor improves the flow behavior and power consumption of the case.

scholarly journals Towards an Efficient CNN Inference Architecture Enabling In-Sensor Processing

Sensors ◽  
2021 ◽  
Vol 21 (6) ◽  
pp. 1955
Author(s):  
Md Jubaer Hossain Pantho ◽  
Pankaj Bhowmik ◽  
Christophe Bobda
Keyword(s):  
Power Consumption ◽  
High Speed ◽  
Image Sensor ◽  
Machine Learning Algorithms ◽  
Hierarchical Optimization ◽  
Computation Method ◽  
Optimization Approach ◽  
Efficient Computation ◽  
Feature Maps ◽  
Dynamic Power

The astounding development of optical sensing imaging technology, coupled with the impressive improvements in machine learning algorithms, has increased our ability to understand and extract information from scenic events. In most cases, Convolution neural networks (CNNs) are largely adopted to infer knowledge due to their surprising success in automation, surveillance, and many other application domains. However, the convolution operations’ overwhelming computation demand has somewhat limited their use in remote sensing edge devices. In these platforms, real-time processing remains a challenging task due to the tight constraints on resources and power. Here, the transfer and processing of non-relevant image pixels act as a bottleneck on the entire system. It is possible to overcome this bottleneck by exploiting the high bandwidth available at the sensor interface by designing a CNN inference architecture near the sensor. This paper presents an attention-based pixel processing architecture to facilitate the CNN inference near the image sensor. We propose an efficient computation method to reduce the dynamic power by decreasing the overall computation of the convolution operations. The proposed method reduces redundancies by using a hierarchical optimization approach. The approach minimizes power consumption for convolution operations by exploiting the Spatio-temporal redundancies found in the incoming feature maps and performs computations only on selected regions based on their relevance score. The proposed design addresses problems related to the mapping of computations onto an array of processing elements (PEs) and introduces a suitable network structure for communication. The PEs are highly optimized to provide low latency and power for CNN applications. While designing the model, we exploit the concepts of biological vision systems to reduce computation and energy. We prototype the model in a Virtex UltraScale+ FPGA and implement it in Application Specific Integrated Circuit (ASIC) using the TSMC 90nm technology library. The results suggest that the proposed architecture significantly reduces dynamic power consumption and achieves high-speed up surpassing existing embedded processors’ computational capabilities.

scholarly journals Design and thermal characteristic analysis of motorized spindle cooling system

2021 ◽  
Vol 13 (5) ◽  
pp. 168781402110208
Author(s):  
Yuan Zhang ◽  
Lifeng Wang ◽  
Yaodong Zhang ◽  
Yongde Zhang
Keyword(s):  
Flow Rate ◽  
High Speed ◽  
Thermal Deformation ◽  
Cooling System ◽  
Thermal Characteristic ◽  
Water Flow Rate ◽  
Thermal Characteristics ◽  
Characteristic Analysis ◽  
Motorized Spindle ◽  
Experiment And Simulation

The thermal deformation of high-speed motorized spindle will affect its reliability, so fully considering its thermal characteristics is the premise of optimal design. In order to study the thermal characteristics of high-speed motorized spindles, a coupled model of thermal-flow-structure was established. Through experiment and simulation, the thermal characteristics of spiral cooling motorized spindle are studied, and the U-shaped cooled motorized spindle is designed and optimized. The simulation results show that when the diameter of the cooling channel is 7 mm, the temperature of the spiral cooling system is lower than that of the U-shaped cooling system, but the radial thermal deformation is greater than that of the U-shaped cooling system. As the increase of the channel diameter of U-shaped cooling system, the temperature and radial thermal deformation decrease. When the diameter is 10 mm, the temperature and radial thermal deformation are lower than the spiral cooling system. And as the flow rate increases, the temperature and radial thermal deformation gradually decrease, which provides a basis for a reasonable choice of water flow rate. The maximum error between experiment and simulation is 2°C, and the error is small, which verifies the accuracy and lays the foundation for future research.

scholarly journals A Low-Power 12-Bit 20 MS/s Asynchronously Controlled SAR ADC for WAVE ITS Sensor Based Applications

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2260
Author(s):  
Khuram Shehzad ◽  
Deeksha Verma ◽  
Danial Khan ◽  
Qurat Ul Ain ◽  
Muhammad Basim ◽  
...  
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
High Speed ◽  
Intelligent Transportation System ◽  
Cmos Process ◽  
Process Technology ◽  
Back Issue ◽  
Digital To Analog Converter ◽  
Analog To Digital ◽  
Switching Method

A low power 12-bit, 20 MS/s asynchronously controlled successive approximation register (SAR) analog-to-digital converter (ADC) to be used in wireless access for vehicular environment (WAVE) intelligent transportation system (ITS) sensor based application is presented in this paper. To optimize the architecture with respect to power consumption and performance, several techniques are proposed. A switching method which employs the common mode charge recovery (CMCR) switching process is presented for capacitive digital-to-analog converter (CDAC) part to lower the switching energy. The switching technique proposed in our work consumes 56.3% less energy in comparison with conventional CMCR switching method. For high speed operation with low power consumption and to overcome the kick back issue in the comparator part, a mutated dynamic-latch comparator with cascode is implemented. In addition, to optimize the flexibility relating to the performance of logic part, an asynchronous topology is employed. The structure is fabricated in 65 nm CMOS process technology with an active area of 0.14 mm2. With a sampling frequency of 20 MS/s, the proposed architecture attains signal-to-noise distortion ratio (SNDR) of 65.44 dB at Nyquist frequency while consuming only 472.2 µW with 1 V power supply.

scholarly journals Interactive Effects in Two-Droplets Combustion of RP-3 Kerosene under Sub-Atmospheric Pressure

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1229
Author(s):  
Hongtao Zhang ◽  
Zhihua Wang ◽  
Yong He ◽  
Jie Huang ◽  
Kefa Cen
Keyword(s):  
Burning Rate ◽  
Atmospheric Pressure ◽  
High Speed ◽  
Ambient Pressure ◽  
Interactive Effects ◽  
Propagation Time ◽  
High Speed Camera ◽  
Single Droplet ◽  
Fuel Droplets ◽  
Spacing Distance

To improve our understanding of the interactive effects in combustion of binary multicomponent fuel droplets at sub-atmospheric pressure, combustion experiments were conducted on two fibre-supported RP-3 kerosene droplets at pressures from 0.2 to 1.0 bar. The burning life of the interactive droplets was recorded by a high-speed camera and a mirrorless camera. The results showed that the flame propagation time from burning droplet to unburned droplet was proportional to the normalised spacing distance between droplets and the ambient pressure. Meanwhile, the maximum normalised spacing distance from which the left droplet can be ignited has been investigated under different ambient pressure. The burning rate was evaluated and found to have the same trend as the single droplet combustion, which decreased with the reduction in the pressure. For every experiment, the interactive coefficient was less than one owing to the oxygen competition, except for the experiment at L/D0 = 2.5 and P = 1.0 bar. During the interactive combustion, puffing and microexplosion were found to have a significant impact on secondary atomization, ignition and extinction.

Sign in / Sign up

Export Citation Format

Share Document