Field Measurement of Platform Behavior, Comparison With Design, and Long-Term Monitoring of Responses Stability After Three Years of Service

1984 ◽  
Vol 106 (4) ◽  
pp. 412-418
Author(s):  
P. F. Ansquer ◽  
S. A. Antalovsky ◽  
E. Hjelde ◽  
G. Agnello
Keyword(s):  
Field Data ◽  
Actual Behavior ◽  
Long Term Stability ◽  
Wave Measurements ◽  
A Value ◽  
Design Values ◽  
Term Basis ◽  
The Stability ◽  
Gravity Platform

Field data from structural, geotechnical and wave measurements made on the concrete gravity platform TCP2 of the Norwegian FRIGG field are disclosed in this paper. Data recorded during 3 yr are interpreted and compared to design values. The stability of invariant parameters has been followed and demonstrated in view of monitoring the long-term behavior stability of the platform. The measured behavior differs from the design behavior and exhibits that design assumptions were conservative. Particularly during this 3-yr period the platform experienced very severe storms with waves up to 25.7 m, a value close to the maximum design wave (100-yr wave: 29 m). It is shown from field data how a bridge connection to a neighboring platform may influence the actual behavior compared to the design one and must be taken into account to understand the measured behavior. It is finally shown that supposed invariant parameters like natural frequencies and others are stable on a long-term basis, and how these invariants are intended to be used for the long-term stability monitoring.

The Stability of the WHO Reference Thromboplastin NIBS & C 67/40

1979 ◽  
Vol 42 (04) ◽  
pp. 1135-1140 ◽  
Author(s):  
G I C Ingram
Keyword(s):  
Human Brain ◽  
Collaborative Study ◽  
Calibration Constant ◽  
Long Term Stability ◽  
Freeze Dried ◽  
Show Evidence ◽  
Human Material ◽  
Reference Preparation ◽  
The Stability

SummaryThe International Reference Preparation of human brain thromboplastin coded 67/40 has been thought to show evidence of instability. The evidence is discussed and is not thought to be strong; but it is suggested that it would be wise to replace 67/40 with a new preparation of human brain, both for this reason and because 67/40 is in a form (like Thrombotest) in which few workers seem to use human brain. A �plain� preparation would be more appropriate; and a freeze-dried sample of BCT is recommended as the successor preparation. The opportunity should be taken also to replace the corresponding ox and rabbit preparations. In the collaborative study which would be required it would then be desirable to test in parallel the three old and the three new preparations. The relative sensitivities of the old preparations could be compared with those found in earlier studies to obtain further evidence on the stability of 67/40; if stability were confirmed, the new preparations should be calibrated against it, but if not, the new human material should receive a calibration constant of 1.0 and the new ox and rabbit materials calibrated against that.The types of evidence available for monitoring the long-term stability of a thromboplastin are discussed.

scholarly journals Limitations and Challenges in the Stability of Cysteamine Eye Drop Compounded Formulations

2021 ◽  
Vol 15 (1) ◽  
pp. 2
Author(s):  
Cristina Martín-Sabroso ◽  
Mario Alonso-González ◽  
Ana Fernández-Carballido ◽  
Juan Aparicio-Blanco ◽  
Damián Córdoba-Díaz ◽  
...  
Keyword(s):  
Shelf Life ◽  
Stability Study ◽  
Eye Drops ◽  
Microbiological Analysis ◽  
Nitrogen Gas ◽  
Long Term Stability ◽  
Main Degradation Product ◽  
The Stability ◽  
Unstable Molecule

Accumulation of cystine crystals in the cornea of patients suffering from cystinosis is considered pathognomonic and can lead to severe ocular complications. Cysteamine eye drop compounded formulations, commonly prepared by hospital pharmacy services, are meant to diminish the build-up of corneal cystine crystals. The objective of this work was to analyze whether the shelf life proposed for six formulations prepared following different protocols used in hospital pharmacies is adequate to guarantee the quality and efficacy of cysteamine eye drops. The long-term and in-use stabilities of these preparations were studied using different parameters: content of cysteamine and its main degradation product cystamine; appearance, color and odor; pH and viscosity; and microbiological analysis. The results obtained show that degradation of cysteamine was between 20% and 50% after one month of storage in the long-term stability study and between 35% and 60% in the in-use study. These data confirm that cysteamine is a very unstable molecule in aqueous solution, the presence of oxygen being the main degradation factor. Saturation with nitrogen gas of the solutions offers a means of reducing cysteamine degradation. Overall, all the formulae studied presented high instability at the end of their shelf life, suggesting that their clinical efficacy might be dramatically compromised.

LONG-TERM STABILITY ANALYSIS OF ACOUSTIC ABSORBING BOUNDARY CONDITIONS

2013 ◽  
Vol 23 (11) ◽  
pp. 2129-2154 ◽  
Author(s):  
HÉLÈNE BARUCQ ◽  
JULIEN DIAZ ◽  
VÉRONIQUE DUPRAT
Keyword(s):  
Stability Analysis ◽  
Boundary Conditions ◽  
Absorbing Boundary Conditions ◽  
Computational Domain ◽  
Acoustic Wave Equation ◽  
Absorbing Boundary ◽  
Term Stability ◽  
Long Term Stability ◽  
The Stability

This work deals with the stability analysis of a one-parameter family of Absorbing Boundary Conditions (ABC) that have been derived for the acoustic wave equation. We tackle the problem of long-term stability of the wave field both at the continuous and the numerical levels. We first define a function of energy and show that it is decreasing in time. Its discrete form is also decreasing under a Courant–Friedrichs–Lewy (CFL) condition that does not depend on the ABC. Moreover, the decay rate of the continuous energy can be determined: it is exponential if the computational domain is star-shaped and this property can be illustrated numerically.

A Review of Preparation and Tribological Applications of Pickering Emulsion

2021 ◽  
pp. 1-27
Author(s):  
Yichen Bao ◽  
Kai Liu ◽  
Quan Zheng ◽  
Lulu Yao ◽  
Yufu Xu
Keyword(s):  
Pickering Emulsion ◽  
Solid Particles ◽  
Preparation Methods ◽  
Factors Affecting ◽  
Long Term Stability ◽  
New Strategy ◽  
New Type ◽  
The Stability ◽  
Near Future

Abstract Pickering emulsion is a new type of stable emulsion made by ultra-fine solid particles instead of traditional surfactants as stabilizers, which has received widespread attention in recent years. The preparation methods of stator-rotor homogenization, high-pressure homogenization, and ultrasonic emulsification were compared with others in this work. The main factors affecting the stability of Pickering emulsion are the surface humidity of the solid particles, the polarity of the oil phase, and the oil-water ratio. These factors could affect the nature of the solid particles, the preparation process of Pickering emulsion and the external environment. Consequently, the long-term stability of Pickering emulsion is still a challenge. The tribological investigations of Pickering emulsion were summarized, and the multifunctional Pickering emulsion shows superior prospects for tribological applications. Moreover, the latest development of Pickering emulsion offers a new strategy for smart lubrication in the near future.

Stability of a Piezoresistive Ceramic Pressure Sensor Made With LTCC Technology

2012 ◽  
Vol 2012 (CICMT) ◽  
pp. 000371-000376 ◽  
Author(s):  
Marina Santo Zarnik ◽  
Darko Belavic
Keyword(s):  
Pressure Sensor ◽  
Fatigue Testing ◽  
Low Pressure ◽  
Fatigue Tests ◽  
Point Of View ◽  
Long Term Stability ◽  
Pressure Cycling ◽  
Key Characteristics ◽  
The Stability

This paper discusses the stability of a piezoresistive, LTCC-based, pressure sensor that was designed for measurements in a low-pressure range below 100 mbar. The intrinsic stability of the sensor's offset was evaluated at a constant ambient temperature and different conditions regarding the atmospheric humidity. The sensors were also subjected to functional fatigue tests, which included a full-scale and an overload pressure cycling. The results of the fatigue testing revealed the vulnerability of the sensor's structure from the point of view of the long-term stability and the life-cycle. Nevertheless, the stability of the key characteristics of the prototype sensors was found to be satisfactory for accurate measurements in the low-pressure ranges.

Fabrication of Boron Compensated Hydrogenated Amorphous Silicon Films with Significantly Improved Stability Using Plasma Enhanced Chemical Vapor Deposition Technique

1995 ◽  
Vol 377 ◽  
Author(s):  
Mohan K. Bhan
Keyword(s):  
Chemical Vapor ◽  
Short Term ◽  
Term Stability ◽  
Long Term Stability ◽  
Vapor Deposition Technique ◽  
Improved Stability ◽  
Donor Acceptor ◽  
B Doping ◽  
The Stability

ABSTRACTWe have systematically investigated the effects of addition of sub-ppm levels of boron on the stability of a-Si:H films and p-i-n devices, deposited by PE-CVD technique. The films thus produced with appropriate amounts of boron, show a significant improvement in stability, when soaked under both AM 1.5 (short-term) as well as 10×sun (long-term) illumination conditions. The opto-electronic properties of the films are quite respectable It is concluded that boron compensates the native impurities by forming donor-acceptor pairs, which reduces the “fast” defects and hence the initial degradation of the films. It is also speculated that boron may also be improving the short-term stability, by reducing the recombination of light generated electrons and holes, by converting D° into D+ states. The long-term stability appears to get affected by hydrogen dilution which seems to reduce the amount of “slow” defects. As a result of B doping of i-layer, the initial conversion efficiency of the devices decreases. It is presumed that our devices may contain an enhanced level of boron impurity, than expected, making them as worse material and to degrade less.

scholarly journals Evaluation of long-term stability of mesiodistal axial inclinations of maxillary molars through panoramic radiographs in subjects treated with Pendulum appliance

2016 ◽  
Vol 21 (1) ◽  
pp. 67-74 ◽  
Author(s):  
Caroline Andrade Rocha ◽  
Renato Rodrigues de Almeida ◽  
José Fernando Castanha Henriques ◽  
Carlos Flores-Mir ◽  
Marcio Rodrigues de Almeida
Keyword(s):  
Panoramic Radiograph ◽  
Post Treatment ◽  
Control Group ◽  
Long Term Stability ◽  
Maxillary Molars ◽  
Group Data ◽  
Maxillary Molar ◽  
Pendulum Appliance ◽  
The Stability

Objective: To evaluate the stability of mesiodistal inclination of maxillary molars produced by a pendulum appliance, five years after completion of orthodontic treatment. Angulation changes were compared to an untreated sample. Methods: The sample consisted of 20 patients (14 females and 6 males) with Class II, Division 1 malocclusion that was treated through molar distalization with a pendulum appliance followed by cervical headgear and full fixed appliances. Maxillary molar inclination was evaluated through panoramic radiograph. The mean age at pretreatment was 14.3 ± 1.6 years, whereas at immediate post-treatment it was 18.6 ± 1.8 years, and at long-term post-treatment it was 23.8 ± 2.0 years. A control group of 16 untreated individuals with untreated normocclusion ranging in age from 12 to 17 years old were used as comparison group. Data were statistically analyzed with independent t-tests and ANOVA test followed by Tukey post-hoc tests. Results: Statistically significant differences were found between T1 (94.50) and T2 (98.80) as well as between T2 and T3 (94.70) for maxillary first molars. Maxillary second molars did not show any statistically significant positional changes during the evaluated time periods T1 (107.50), T2 (109.30) and T3 (106.90). Conclusion: Although maxillary first molars underwent distal crown inclination immediately after treatment, approximately five years thereafter their roots tended to upright close to the pretreatment positions.

scholarly journals Long-Term Stability Comparison between an Original and a Generic Version of Piperacillin/Tazobactam in Dextrose 5 % Infusion Polyolefin Bags at 5 ± 3 °C after Microwave Freeze-Thaw Treatment

2018 ◽  
Vol 3 (3) ◽  
pp. 143-151
Author(s):  
Sophie Huvelle ◽  
Marie Godet ◽  
Laurence Galanti ◽  
Mélanie Closset ◽  
Benoît Bihin ◽  
...  
Keyword(s):  
Generic Version ◽  
Generic Product ◽  
Brand Name ◽  
Term Stability ◽  
Long Term Stability ◽  
Ph Values ◽  
Lower Confidence ◽  
The Stability ◽  
Aseptic Conditions

AbstractBackgroundPiperacillin-Tazobactam is frequently infused in hospitals. The use of a generic version was considered after the out of stock of the brand name Tazocin®. The stability of 4 g of Tazocin®in 120 mL of dextrose 5 % (D5) was demonstrated during 35 days at 5 °C ± 3 °C after freezing (−20 °C) and microwave thawing (FMT). The aim of the study was to investigate and compare the long-term stability of Tazocin®and a generic product in the same conditions.MethodsFive polyolefin bags of 4 g of Piperacillin/Tazobactam®Sandoz and 5 bags of 4 g of Tazocin®were prepared under aseptic conditions in 120 mL of D5 and stored 3 months at 20 °C then thawed and stored 58 days at 5 ± 3 °C.Spectrophotometric absorbance at different wavelengths, pH measurement, visual and microscopic observations were also performed.The concentrations were measured by HPLC, at 211 nm for tazobactam and 230 nm for piperacilline.ResultsNo significant change in pH values or optic densities, no crystals were detected. The lower confidence limit at 95 % of the concentration for the solutions remains superior to 90 % of the initial concentration until 58 days of storage at 5 ± 3 °C.ConclusionUnder these conditions, 4 g/120 mL of Piperacillin/Tazobactam®Sandoz or Tazocin®in D5 infusion in polyolefin bags remains stable at least for 58 days at 5 ± 3 °C after FMT

scholarly journals PEMBUATAN PULP DENGAN MEMANFAATKAN LIMBAH KULIT DURIAN (DURIO ZIBETHINUS MURR) DENGAN CAMPURAN (RESINA COLOPHONIUM) GUNA MENCEGAH DEGRADASI LINGKUNGAN

2015 ◽  
Vol 17 (3) ◽  
Author(s):  
Deddy Kurniawan W Kurniawan W ◽  
Fahmi Arifan ◽  
M. Dwi Khoirun Adim
Keyword(s):  
Lignin Content ◽  
Starch Content ◽  
Thick Wall ◽  
Cellulose Content ◽  
Durio Zibethinus ◽  
A Value ◽  
Yield Value ◽  
Term Basis ◽  
High Cellulose

Deddy Kurniawan W, Fahmi Arifan, M. Dwi Khoirun Adim, in this article explain that paper is one of the primary needs for humans today . High paper usage is resulting increased in production of paper . On the other hand, paper which are usually made ​​from cellulose and hemi-cellulose in wood can result environmental degradation , due to the use of wood and tree felling leads to long-term basis that can increase the temperature of the earth surface ( global warming) . Durian is relatively abundant in Indonesia , durian shell contains high cellulose ( 50-60 % ) and lignin content ( 5 %), also  a low starch content ( 5 % ) . Durian shell wastes containing fibre  with dimensions of length and fiber thick wall that be able to bind well when given a synthetic adhesive or an adhesive mineral . Pulp which is produced from durian shell waste in experiments were 1 , 2 , 3 and 4, have a value of α - cellulose content of 35 % , 45 % , 27.7 % , 37.5 % and 57.6 %, respectively. When yield value of  49.2 % , 66.8 % and 48.2 % respectively. Keywords: pulp, durian, gondorukem, digester

Study on Evaluation System of the Agent’s Capability Structure of International Energy Cooperation

2014 ◽  
Vol 1073-1076 ◽  
pp. 2488-2492
Author(s):  
Hong Li Yang ◽  
Ping Li ◽  
Xiao Li Guo
Keyword(s):  
Evaluation System ◽  
Energy Cooperation ◽  
Long Term Stability ◽  
Whole Process ◽  
The Stability ◽  
Building Capability ◽  
Capability Evaluation ◽  
Key Indicators ◽  
The Relationship

With the deepening of economic globalization, cooperation has become a mainstream trend, revealing the discipline of cooperation has become a key scientific issue. As a content of cooperation, international energy cooperation is a system of relations constituted by different energy cooperation agents, it reflects the composition of agents. Ability divergence and their capability system have an effect on the long-term stability and development of cooperation. Based on the theories, this paper put forward the main connotation of cooperation capacity structure, building capability evaluation system, clearing affect the stability of the key indicators of cooperation, exploring the relationship between cooperation agents’ capability structure and cooperative stability in order to study the whole process of international energy cooperation fluctuations trajectory.

Sign in / Sign up

Export Citation Format

Share Document