Discharge Coefficient Correlations for Circular-Arc Venturi Flowmeters at Critical (Sonic) Flow

1974 ◽  
Vol 96 (2) ◽  
pp. 111-123 ◽  
Author(s):  
B. T. Arnberg ◽  
C. L. Britton ◽  
W. F. Seidl
Keyword(s):  
Discharge Coefficient ◽  
Reynolds Numbers ◽  
Critical Flow ◽  
Geometrical Parameters ◽  
Circular Arc ◽  
Property Data ◽  
Operational Variables ◽  
Optimum Approach ◽  
The Mean ◽  
Flow Functions

Data are presented which tend to verify the theoretically predicted discharge coefficients for circular-arc venturi flow meters operating in the critical flow regime (sonic) at throat Reynolds numbers above 1.5 105. Extensive analysis of the data is presented using methods that are presently in process of international standardization. The data tend to verify the theoretically predicted decrease of 0.25 percent in the discharge coefficient during transition from laminar to a turbulent boundary layer. The transition occurred at a throat Reynolds number of 2.2 106, but the transition point probably changes as a function of several influences. The mean line of the measured data fell between the theoretical values for laminar and turbulent boundary layers. The scatter in 55 data points was ±0.212 percent (95 percent confidence level) from the mean line equation for Reynolds numbers from 4.1 104 to 3.4 106, which included the effects of several variables. Data were obtained from 17 venturis with throat sizes from 0.15 to 1.37 in. with Beta ratios ranging from 0.014 to 0.25. Four different test gases and three primary flow measurement facilities were used. Additional data are presented extending down to throat Reynolds numbers of 1.3 104 and throat diameters of 0.05 in. which indicate special problems in these regions. The state of the art for measuring venturi throat diameters presented a major limitation to the correlation effort. Calibration is necessary in many cases depending on various parameters and requirements. Additional study is needed to determine the optimum geometrical parameters at low Reynolds numbers, the optimum approach configuration for Beta ratios above 0.1, the effect of surface roughness on the discharge coefficient, and the effect of various operational variables such as flow pulsation and approach velocity profile. Also, a continuous effort should be made to improve the critical flow functions for real gases as better gas property data become available, and to extend these calculations to broader ranges of pressures and temperatures, and to other gases.

scholarly journals Aerodynamics of smooth and rough square-section prisms at incidence in very high Reynolds-number cross-flows

2021 ◽  
Vol 62 (3) ◽  
Author(s):  
Nils Paul van Hinsberg
Keyword(s):  
Reynolds Number ◽  
Cross Sections ◽  
Reynolds Numbers ◽  
Circular Cylinders ◽  
Surface Boundary ◽  
Experimental Proof ◽  
Surface Boundary Layer ◽  
Pitch Moment ◽  
The Mean ◽  
High Reynolds

Abstract The aerodynamics of smooth and slightly rough prisms with square cross-sections and sharp edges is investigated through wind tunnel experiments. Mean and fluctuating forces, the mean pitch moment, Strouhal numbers, the mean surface pressures and the mean wake profiles in the mid-span cross-section of the prism are recorded simultaneously for Reynolds numbers between 1$$\times$$ × 10$$^{5}$$ 5 $$\le$$ ≤ Re$$_{D}$$ D $$\le$$ ≤ 1$$\times$$ × 10$$^{7}$$ 7 . For the smooth prism with $$k_s$$ k s /D = 4$$\times$$ × 10$$^{-5}$$ - 5 , tests were performed at three angles of incidence, i.e. $$\alpha$$ α = 0$$^{\circ }$$ ∘ , −22.5$$^{\circ }$$ ∘ and −45$$^{\circ }$$ ∘ , whereas only both “symmetric” angles were studied for its slightly rough counterpart with $$k_s$$ k s /D = 1$$\times$$ × 10$$^{-3}$$ - 3 . First-time experimental proof is given that, within the accuracy of the data, no significant variation with Reynolds number occurs for all mean and fluctuating aerodynamic coefficients of smooth square prisms up to Reynolds numbers as high as $$\mathcal {O}$$ O (10$$^{7}$$ 7 ). This Reynolds-number independent behaviour applies to the Strouhal number and the wake profile as well. In contrast to what is known from square prisms with rounded edges and circular cylinders, an increase in surface roughness height by a factor 25 on the current sharp-edged square prism does not lead to any notable effects on the surface boundary layer and thus on the prism’s aerodynamics. For both prisms, distinct changes in the aerostatics between the various angles of incidence are seen to take place though. Graphic abstract

scholarly journals Plunging Airfoil: Reynolds Number and Angle of Attack Effects

Aerospace ◽  
2021 ◽  
Vol 8 (8) ◽  
pp. 216
Author(s):  
Emanuel A. R. Camacho ◽  
Fernando M. S. P. Neves ◽  
André R. R. Silva ◽  
Jorge M. M. Barata
Keyword(s):  
Reynolds Number ◽  
High Performance ◽  
Angle Of Attack ◽  
Systems Design ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Low Reynolds Numbers ◽  
Operational Conditions ◽  
Naca0012 Airfoil ◽  
The Mean

Natural flight has consistently been the wellspring of many creative minds, yet recreating the propulsive systems of natural flyers is quite hard and challenging. Regarding propulsive systems design, biomimetics offers a wide variety of solutions that can be applied at low Reynolds numbers, achieving high performance and maneuverability systems. The main goal of the current work is to computationally investigate the thrust-power intricacies while operating at different Reynolds numbers, reduced frequencies, nondimensional amplitudes, and mean angles of attack of the oscillatory motion of a NACA0012 airfoil. Simulations are performed utilizing a RANS (Reynolds Averaged Navier-Stokes) approach for a Reynolds number between 8.5×103 and 3.4×104, reduced frequencies within 1 and 5, and Strouhal numbers from 0.1 to 0.4. The influence of the mean angle-of-attack is also studied in the range of 0∘ to 10∘. The outcomes show ideal operational conditions for the diverse Reynolds numbers, and results regarding thrust-power correlations and the influence of the mean angle-of-attack on the aerodynamic coefficients and the propulsive efficiency are widely explored.

Axisymmetric internal waves generated by a travelling oscillating body

1969 ◽  
Vol 35 (2) ◽  
pp. 219-224 ◽  
Author(s):  
T. N. Stevenson
Keyword(s):  
Internal Waves ◽  
Salt Solution ◽  
Reynolds Numbers ◽  
Mean Velocity ◽  
Dispersive Waves ◽  
The Mean ◽  
Oscillating Sphere

Experiments are presented in which axisymmetric internal waves are generated by an oscillating sphere moving vertically in a stably stratified salt solution. The Reynolds numbers for the sphere based on the diameter and the mean velocity are between 10 and 200. Lighthill's theory for dispersive waves is used to calculate the phase configuration of the internal waves. The agreement between experiment and theory is reasonably good.

scholarly journals Experimental Investigation of Tandem Blade Cascades With Double-Circular ARC Profiles

1985 ◽  
Author(s):  
Wu Guochuan ◽  
Zhuang Biaonan ◽  
Guo Bingheng
Keyword(s):  
Experimental Investigation ◽  
Reynolds Number ◽  
Mach Number ◽  
Total Pressure ◽  
Incidence Angle ◽  
Axial Direction ◽  
Geometrical Parameters ◽  
Optimal Conditions ◽  
Turning Angle ◽  
Circular Arc

24 double circular are tandem blade cascades of three different chord-ratios were investigated under different displacements in peripheral and axial direction. The inlet Mach number was 0.3. The Reynolds number based on blade chord was 2.7×105. The characteristics of the tandem blade cascades, such as the dependence of turning angle and coefficient of total pressure loss on incidence angle were obtained. The ranges of main geometrical parameters under optimal conditions were recommended.

Heat Transfer and Flowfield Measurements in the Leading Edge Region of a Stator Vane Endwall

1999 ◽  
Vol 121 (3) ◽  
pp. 558-568 ◽  
Author(s):  
M. B. Kang ◽  
A. Kohli ◽  
K. A. Thole
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Edge Region ◽  
Leading Edge Vortex ◽  
Stator Vane ◽  
Edge Vortex ◽  
The Mean

The leading edge region of a first-stage stator vane experiences high heat transfer rates, especially near the endwall, making it very important to get a better understanding of the formation of the leading edge vortex. In order to improve numerical predictions of the complex endwall flow, benchmark quality experimental data are required. To this purpose, this study documents the endwall heat transfer and static pressure coefficient distribution of a modern stator vane for two different exit Reynolds numbers (Reex = 6 × 105 and 1.2 × 106). In addition, laser-Doppler velocimeter measurements of all three components of the mean and fluctuating velocities are presented for a plane in the leading edge region. Results indicate that the endwall heat transfer, pressure distribution, and flowfield characteristics change with Reynolds number. The endwall pressure distributions show that lower pressure coefficients occur at higher Reynolds numbers due to secondary flows. The stronger secondary flows cause enhanced heat transfer near the trailing edge of the vane at the higher Reynolds number. On the other hand, the mean velocity, turbulent kinetic energy, and vorticity results indicate that leading edge vortex is stronger and more turbulent at the lower Reynolds number. The Reynolds number also has an effect on the location of the separation point, which moves closer to the stator vane at lower Reynolds numbers.

scholarly journals Numerical Modeling of Flow Over a Rectangular Broad-Crested Weir with a Sloped Upstream Face

Water ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1663 ◽  
Author(s):  
Lei Jiang ◽  
Mingjun Diao ◽  
Haomiao Sun ◽  
Yu Ren
Keyword(s):  
Numerical Simulations ◽  
Discharge Coefficient ◽  
Separation Zone ◽  
Turbulence Models ◽  
Numerical Results ◽  
Upstream Face ◽  
Flow Conditions ◽  
Flow Features ◽  
The Mean ◽  
Absolute Percent Error

The objective of this study was to evaluate the effect of the upstream angle on flow over a trapezoidal broad-crested weir based on numerical simulations using the open-source toolbox OpenFOAM. Eight trapezoidal broad-crested weir configurations with different upstream face angles (θ = 10°, 15°, 22.5°, 30°, 45°, 60°, 75°, 90°) were investigated under free-flow conditions. The volume-of-fluid (VOF) method and two turbulence models (the standard k-ε model and the SST k-w model) were employed in the numerical simulations. The numerical results were compared with the experimental results obtained from published papers. The root mean square error (RMSE) and the mean absolute percent error (MAPE) were used to evaluate the accuracy of the numerical results. The statistical results show that RMSE and MAPE values of the standard k-ε model are 0.35–0.67% and 0.50–1.48%, respectively; the RMSE and MAPE values of the SST k-w model are 0.25–0.66% and 0.55–1.41%, respectively. Additionally, the effects of the upstream face angle on the flow features, including the discharge coefficient and the flow separation zone, were also discussed in the present study.

Loss Characteristics of Orifices and Nozzles

1978 ◽  
Vol 100 (3) ◽  
pp. 299-307 ◽  
Author(s):  
S. H. Alvi ◽  
K. Sridharan ◽  
N. S. Lakshmana Rao
Keyword(s):  
Reynolds Number ◽  
Turbulent Flow ◽  
Flow Regime ◽  
Discharge Coefficient ◽  
Critical Reynolds Number ◽  
Reynolds Numbers ◽  
Center Line ◽  
Laminar Regime ◽  
Variation Of Parameters ◽  
Turbulent Flow Regime

Loss characteristics of sharp-edged orifices, quadrant-edged orifices for varying edge radii, and nozzles are studied for Reynolds numbers less than 10,000 for β ratios from 0.2 to 0.8. The results may be reliably extrapolated to higher Reynolds numbers. Presentation of losses as a percentage of meter pressure differential shows that the flow can be identified into fully laminar regime, critical Reynolds number regime, relaminarization regime, and turbulent flow regime. An integrated picture of variation of parameters such as discharge coefficient, loss coefficient, settling length, pressure recovery length, and center line velocity confirms this classification.

Super-Fine Structure in the Critical Flow-Rate of Critical Flow Venturi Nozzles

2002 ◽  
Author(s):  
Masahiro Ishibashi
Keyword(s):  
Fine Structure ◽  
Steady State ◽  
Discharge Coefficient ◽  
Constant Pressure ◽  
Pressure Ratio ◽  
Critical Flow ◽  
Time Intervals ◽  
Critical Flow Rate ◽  
A Value ◽  
Long Time

It is shown that critical flow Venturi nozzles need time intervals, i.e., more than five hours, to achieve steady state conditions. During these intervals, the discharge coefficient varies gradually to reach a value inherent to the pressure ratio applied. When a nozzle is suddenly put in the critical condition, its discharge coefficient is trapped at a certain value then afterwards approaches gradually to the inherent value. Primary calibrations are considered to have measured the trapped discharge coefficient, whereas nozzles in applications, where a constant pressure ratio is applied for a long time, have a discharge coefficient inherent to the pressure ratio; inherent and trapped coefficients can differ by 0.03–0.04%.

scholarly journals Design and Testing of a LUT Airfoil for Straight-Bladed Vertical Axis Wind Turbines

2018 ◽  
Vol 8 (11) ◽  
pp. 2266 ◽  
Author(s):  
Shoutu Li ◽  
Ye Li ◽  
Congxin Yang ◽  
Xuyao Zhang ◽  
Qing Wang ◽  
...  
Keyword(s):  
Wind Turbines ◽  
Lift Coefficient ◽  
Pressure Coefficient ◽  
Vertical Axis ◽  
Reynolds Numbers ◽  
Optimization Method ◽  
Geometrical Parameters ◽  
Vertical Axis Wind Turbines ◽  
University Of Technology ◽  
Horizontal Axis Wind Turbines

The airfoil plays an important role in improving the performance of wind turbines. However, there is less research dedicated to the airfoils for Vertical Axis Wind Turbines (VAWTs) compared to the research on Horizontal Axis Wind Turbines (HAWTs). With the objective of maximizing the aerodynamic performance of the airfoil by optimizing its geometrical parameters and by considering the law of motion of VAWTs, a new airfoil, designated the LUT airfoil (Lanzhou University of Technology), was designed for lift-driven VAWTs by employing the sequential quadratic programming optimization method. Afterwards, the pressure on the surface of the airfoil and the flow velocity were measured in steady conditions by employing wind tunnel experiments and particle image velocimetry technology. Then, the distribution of the pressure coefficient and aerodynamic loads were analyzed for the LUT airfoil under free transition. The results show that the LUT airfoil has a moderate thickness (20.77%) and moderate camber (1.11%). Moreover, compared to the airfoils commonly used for VAWTs, the LUT airfoil, with a wide drag bucket and gentle stall performance, achieves a higher maximum lift coefficient and lift–drag ratios at the Reynolds numbers 3 × 105 and 5 × 105.

Sign in / Sign up

Export Citation Format

Share Document