Effect of Mechanical Alloying on Al6061-Graphene Composite Fabricated by Semi-Solid Powder Processing

2013 ◽  
Author(s):  
Mina Bastwros ◽  
Gap-Yong Kim ◽  
Can Zhu ◽  
Kun Zhang ◽  
Shiren Wang
Keyword(s):  
Mechanical Properties ◽  
Powder Processing ◽  
Milled Powder ◽  
High Strength ◽  
Bending Test ◽  
Maximum Enhancement ◽  
Three Point Bending ◽  
Graphene Composite ◽  
Semi Solid ◽  
Al6061 Powder

Graphene is a promising material as a reinforcing element for high-strength, lightweight metal composites due to its extraordinary mechanical properties and low density. In this study, Al6061–graphene composite was investigated with 1.0 wt.% graphene reinforcement. The graphene was manufactured by the modified Brodie’s method. The Al6061 powder and graphene flakes were ball milled at different milling times (10, 30, 60, and 90 min). The composite was then synthesized by hot compaction in the semi-solid regime of the Al6061. Three point bending test was performed to characterize the mechanical properties of the composites. The ball milled powder and the fracture surfaces of the composites were investigated using the scanning electron microscopy (SEM). The results were compared with a reference Al6061 without any graphene reinforcement. For the Al6061-1.0 wt.% graphene composites, a maximum enhancement of 47% in the flexural strength was observed when compared with the reference Al6061 processed at the same condition.

Fabrication of Graphene Reinforced Aluminum Composite by Semi-Solid Processing

2013 ◽  
Author(s):  
Mina Bastwros ◽  
Gap-Yong Kim ◽  
Kun Zhang ◽  
Shiren Wang
Keyword(s):  
Mechanical Properties ◽  
Microstructural Analysis ◽  
High Strength ◽  
Strength Properties ◽  
Bending Test ◽  
Aluminum Composite ◽  
Reinforced Composite ◽  
Uniform Dispersion ◽  
Semi Solid ◽  
Al6061 Powder

A composite made of graphene and aluminum is a promising material for many engineering applications due to its lightweight and relatively high strength properties. Unfortunately, the uniform dispersion of the graphene is considered one of the big challenges since the graphene clusters tend to deteriorate the mechanical properties of the composite. In this study, a graphene reinforced Al6061 composite has been investigated. The composites are fabricated by ball milling the graphene flakes and the Al6061 powder, followed by hot compaction in the semi-solid regime of the Al6061. In addition, a graphene reinforced composite with localized reinforced zones within the composite was also investigated The mechanical properties of the composites are measured by conducting a bend test, and microstructural analysis of the composite and fracture surfaces are performed. According to the bending test results, an enhancement in the strength is clearly observed.

Influence of Honeycomb Core Compression on the Mechanical Properties of the Sandwich Structure

2013 ◽  
Vol 486 ◽  
pp. 283-288
Author(s):  
Ladislav Fojtl ◽  
Soňa Rusnáková ◽  
Milan Žaludek
Keyword(s):  
Mechanical Properties ◽  
Impact Test ◽  
Charpy Impact ◽  
Charpy Impact Test ◽  
Low Velocity Impact ◽  
Bending Test ◽  
Honeycomb Core ◽  
Low Velocity ◽  
Three Point Bending ◽  
Core Technology

This research paper deals with an investigation of the influence of honeycomb core compression on the mechanical properties of sandwich structures. These structures consist of prepreg facing layers and two different material types of honeycomb and are produced by modified compression molding called Crush-Core technology. Produced structures are mechanically tested in three-point bending test and subjected to low-velocity impact and Charpy impact test.

Crystal Phase Formation and Mechanical Properties of Lithium Disilicate Glass-Ceramics for Dental Restoration

2010 ◽  
Vol 177 ◽  
pp. 447-450 ◽  
Author(s):  
Xin Zhang ◽  
Yi Wen Hu ◽  
Yin Wu ◽  
Wen Jie Si
Keyword(s):  
Mechanical Properties ◽  
Phase Formation ◽  
Glass Ceramics ◽  
High Strength ◽  
Lithium Disilicate ◽  
Sem Analysis ◽  
Dental Restoration ◽  
Bending Test ◽  
Crystal Phase ◽  
High Temperature Xrd

The purpose of this study was to evaluate the crystal phase formation behavior and its influence on the mechanical properties of LiO2-SiO2-P2O5 glass-ceramics system. High temperature XRD was used to analyze the crystal phase formation in situ. The crystalline phases in the material both before and after heat-treatment were also analyzed. The flexural strength was measured by three-point bending test according to ISO 6872:2008(E). The SEM analysis showed that the high strength of the glass-ceramics is attributed to the continuous interlocking microstructure with fine lithium disilicate crystallines.

Comparison of the Cross Sectional Area, the Loss in Volume and the Mechanical Properties of LAE442 and MgCa0.8 as Resorbable Magnesium Alloy Implants after 12 Months Implantation Duration

2010 ◽  
Vol 638-642 ◽  
pp. 675-680 ◽  
Author(s):  
Martina Thomann ◽  
Nina von der Höh ◽  
Dirk Bormann ◽  
Dina Rittershaus ◽  
C. Krause ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Degradation Process ◽  
Cross Sectional Area ◽  
Bending Test ◽  
Sectional Area ◽  
Cross Sectional ◽  
Initial Strength ◽  
Three Point Bending ◽  
The Cross

Current research focuses on magnesium based alloys in the course of searching a resorbable osteosynthetic material which provides sufficient mechanical properties besides a good biocompatibility. Previous studies reported on a favorable biocompatibility of the alloys LAE442 and MgCa0.8. The present study compared the degradation process of cylindrical LAE442 and MgCa0.8 implants after 12 months implantation duration. Therefore, 10 extruded implants (2.5 x 25 mm, cross sectional area 4.9 mm²) of both alloys were implanted into the medullary cavity of both tibiae of rabbits for 12 months. After euthanization, the right bone-implant-compound was scanned in a µ-computed tomograph (µCT80, ScancoMedical) and nine uniformly distributed cross-sections of each implant were used to determine the residual implants´ cross sectional area (Software AxioVisionRelease 4.5, Zeiss). Left implants were taken out of the bone carefully. After weighing, a three-point bending test was carried out. LAE442 implants degraded obviously slower and more homogeneously than MgCa0.8. The mean residual cross sectional area of LAE442 implants was 4.7 ± 0.07 mm². MgCa0.8 showed an area of only 2.18 ± 1.03 mm². In contrast, the loss in volume of LAE442 pins was more obvious. They lost 64 % of their initial weight. The volume of MgCa0.8 reduced clearly to 54.4 % which corresponds to the cross sectional area results. Three point bending tests revealed that LAE442 showed a loss in strength of 71.2 % while MgCa0.8 lost 85.6 % of its initial strength. All results indicated that LAE442 implants degraded slowly, probably due to the formation of a very obvious degradation layer. Degradation of MgCa0.8 implants was far advanced.

Investigation of Mechanical Properties of Nano Sized Clay/LDH Particle as Hybrid Nano Composite Material

2015 ◽  
Vol 766-767 ◽  
pp. 355-361
Author(s):  
S. Sivasaravanan ◽  
V.K. Bupesh Raja ◽  
S. Prabhu ◽  
S. Dineshkumar ◽  
Gokulaprasad
Keyword(s):  
Composite Material ◽  
Testing Machine ◽  
Weight Ratio ◽  
High Strength ◽  
Sem Analysis ◽  
Bending Test ◽  
Flexural Property ◽  
Weight Percentage ◽  
Three Point Bending ◽  
Sonication Technique

Usage of Hybrid nanocomposite materials provides a greater opportunity to replace the conventional materials due to their properties such as light weight and high strength to based on weight ratio. In this synergitic study, nanosized clay particle and layered double hydroxide particles are used. nanoclay and LDH particles were mixed on the bases of weight percentage (1wt% to 5wt%) by ultra sonication technique. The composite material was fabricated by one of the most common method known as hand lay-up technique. The composite materials was prepared in the form of plate with 4mm of thickness.The characterization of tensile and flexural property of the nanoclay, LDH and combination of both was analysis by tensile test using universal testing machine and three point bending test respectively. The tensile and three point bending test specimens were cut to size as per ASTM standard.The morphology of composite was studied using SEM analysis.

An Experimental Evaluation of Energy Absorption of TRIP Steel by Small Punch Test

2016 ◽  
Vol 725 ◽  
pp. 60-65
Author(s):  
Asuka Hayashi ◽  
Takeshi Iwamoto
Keyword(s):  
Energy Absorption ◽  
Trip Steel ◽  
Dynamic Condition ◽  
High Strength ◽  
High Energy ◽  
Bending Test ◽  
Absorption Characteristic ◽  
Small Punch ◽  
Three Point Bending ◽  
Punch Test

TRIP steel possesses high strength and excellent ductility. In addition, it is possible that TRIP steel indicates high energy absorption so that TRIP steel is expected to apply to automotive members. To design the members made of TRIP steel, it is important to clarify its energy absorption characteristic at various deformation rates. In the previous study, the energy absorption characteristic of TRIP steel is evaluated by J-integral under quasi-static to dynamic condition by using a thick specimen based on ASTM standard. However, by using such thick specimens, it is difficult to conduct the three-point bending test under impact condition because of high ductility in TRIP steel. A small punch (SP) test is the experimental method which can evaluate fracture parameters such as J-integral. By using a conventional use of small specimen in the SP test, it is possible to evaluate J-integral of TRIP steel under impact deformation. In this study, energy absorption characteristic of TRIP steel is investigated by SP test under different deflection rates. Then, the relationship between the values of J-integral obtained by previously conducted three-point bending test and the SP test of TRIP steel is discussed.

J Integral of Steel Fiber Reinforced High Strength Concrete

2012 ◽  
Vol 476-478 ◽  
pp. 1568-1571
Author(s):  
Ting Yi Zhang ◽  
Guang He Zheng ◽  
Ping Wang ◽  
Kai Zhang ◽  
Huai Sen Cai
Keyword(s):  
High Strength Concrete ◽  
Fiber Volume Fraction ◽  
Steel Fiber ◽  
Volume Fraction ◽  
High Strength ◽  
Bending Test ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Three Point Bending ◽  
Strength Concrete

Through the three-point bending test on the specimens of steel fiber reinforced high strength concrete (SFHSC), the effects of influencing factors including water-cement ratio (W/C) and the fiber volume fraction (ρf) upon the critical value(JC) of J integral were studied. The results show that the variation tendencies of JC are different under different factors. JC meets the linear statistical relation with W/C, ρf, respectively.

THE INFLUENCE OF SiC COATING PROCESS ON THE PROPERTIES OF C/C COMPOSITES

2007 ◽  
Vol 14 (04) ◽  
pp. 817-820
Author(s):  
MIN HUANG ◽  
KE-ZHI LI ◽  
HE-JUN LI ◽  
QIAN-GANG FU ◽  
GUO-DONG SUN
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Failure Mode ◽  
Flexural Modulus ◽  
Pack Cementation ◽  
Bending Test ◽  
Carbon Composites ◽  
Coating Process ◽  
Three Point Bending ◽  
Coated Carbon

SiC coating for carbon/carbon composites was prepared by pack cementation method. The effects of coating process on the microstructure and the mechanical properties of C / C composites were analyzed by SEM and three-point bending test, respectively. As the infiltrated Si improved the interfaces bonding during the coating process, the flexural strength and flexural modulus of SiC -coated carbon/carbon composites were both increased by about 10% than the naked C / C composites. In addition, the mechanism of the change of failure mode of SiC coated C / C composites and naked C / C composites was addressed.

The Effect of the Compression on the Mechanical Properties of Wood Material

2007 ◽  
Vol 537-538 ◽  
pp. 41-46 ◽  
Author(s):  
László Kuzsella ◽  
Imre Szabó
Keyword(s):  
Mechanical Properties ◽  
Charpy Impact ◽  
Charpy Impact Test ◽  
Bending Test ◽  
Wood Material ◽  
Ordinary Life ◽  
Three Point Bending ◽  
Wide Range ◽  
New Process ◽  
New Applications

The wood is one of the most favourable structural material. It appears on all fields of the ordinary life. It is difficult to say an application where the wood is not used due to its cheap price, availability and just simply the beauty. Beside of the wide range of process technologies a new process appeared. This process changes the properties of the material and brings many new applications to this traditional material. This process is the compression of the structural wood material. This publication deals with the effect of the compression on the mechanical properties of two hardwoods (beech: fagus sylvatica, oak: quercus) by the help of the three-point bending test and the Charpy impact test.

Sign in / Sign up

Export Citation Format

Share Document