Adsorption, Kinetic and Regeneration Studies of n-Hexane on MIL-101(Cr)/AC

NANO ◽  
2019 ◽  
Vol 14 (08) ◽  
pp. 1950100
Author(s):  
Wenpu Zhao ◽  
Weiqiu Huang ◽  
Manlin Li ◽  
Zhoulan Huang
Keyword(s):  
Activated Carbon ◽  
Adsorption Process ◽  
Carbon Powder ◽  
Structure Parameter ◽  
Pore Structure Parameter ◽  
Order Model ◽  
First Order ◽  
Adsorption Desorption ◽  
Rate Controlling Step

MIL-101(Cr)/AC was synthesized by in situ incorporation of activated carbon powder via hydrothermal method. The water stability, n-hexane adsorption and regeneration of the MIL-101(Cr)/AC were experimentally measured. The results showed that the MIL-101(Cr)/AC exhibited the larger surface area (3319.3[Formula: see text]m2/g) than that of MIL-101(Cr) and AC, respectively. The addition of activated carbon was beneficial to improve the yield of MIL-101(Cr)/AC. The pore structure parameter and XRD of the MIL-101(Cr)/AC changed little after in water for 24[Formula: see text]h. Furthermore, the adsorption capacity of MIL-101(Cr)/AC for n-hexane was 786[Formula: see text]mg/g, which increased to 23.0% and 27.7% compared with MIL-101(Cr) and AC, respectively. Kinetic fitting of data indicated that the pseudo-first order model can more accurately describe the adsorption process of n-hexane on MIL-101(Cr)/AC and the intraparticle diffusion was not the sole rate-controlling step. Besides, the regeneration efficiency of MIL-101(Cr)/AC was over 92% after 10 consecutive n-hexane adsorption/desorption cycles.

Application of raw and modified Uruguayan clays to phosphate adsorption for water remediation

MRS Advances ◽  
2018 ◽  
Vol 3 (61) ◽  
pp. 3543-3549
Author(s):  
Pablo González ◽  
Andrea C. De Los Santos ◽  
Jorge R. Castiglioni ◽  
María A. De León
Keyword(s):  
Nitrogen Adsorption ◽  
Pillared Clay ◽  
Water Remediation ◽  
Phosphate Adsorption ◽  
X Ray Diffraction ◽  
Order Model ◽  
Freundlich Model ◽  
X Ray ◽  
First Order ◽  
Adsorption Desorption

ABSTRACTA raw clay from Uruguay was modified with aluminium to obtain an aluminium pillared clay (Al-PILC). The solids were characterized by scanning electron microscopy, X-ray diffraction and nitrogen adsorption-desorption isotherms. The Al-PILC retained the typical laminar structure of montmorillonite. The specific surface area and the microporous volume of the Al-PILC, 235 m2 g-1 and 0.096 cm3 g-1, respectively, were much higher than those of the clay. The phosphate adsorption capacity of the Al-PILC was higher than those of the clay. The phosphate adsorption kinetic followed the pseudo-first-order model for both, the clay and the Al-PILC, and the phosphate adsorption isotherm for the Al-PILC fit the Freundlich model.

scholarly journals Recovery of phosphate from aqueous solution by magnetically recycled modified polishing powder composites

2019 ◽  
Vol 80 (7) ◽  
pp. 1357-1366
Author(s):  
Jianming Liu ◽  
Runying Bai ◽  
Junfeng Hao ◽  
Bowen Song ◽  
Yu Zhang ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Ligand Exchange ◽  
Adsorption Process ◽  
High Adsorption ◽  
Order Model ◽  
Powder Composites ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ph Level ◽  
Adsorption Desorption

Abstract This study investigated a magnetically recycled modified polishing powder (CMIO@PP) as an adsorbent of phosphate; the CMIO@PP was synthesized by combining the modified La/Ce-containing waste polishing powder with CaO2-modified Fe3O4 (CMIO). Results indicate that the CMIO@PP nanocomposite presents a crystal structure comprising La (OH)3, Ce (OH)3, and Fe3O4, and that CMIO is uniformly dispersed in the modified polishing powder. The CMIO@PP (1:3) is a suitable choice considering its magnetism and adsorption capacity. The magnetic adsorbent exhibits a high adsorption capacity of 53.72 mg/g, a short equilibrium time of 60 min, and superior selectivity for phosphate. Moreover, the adsorbent strongly depends on the pH during the adsorption process and maintains a large adsorption capacity when the pH level is between 2 and 6. The adsorption of phosphate by the CMIO@PP (1:3) accords with the Langmuir isotherm model, and the adsorption process follows the pseudo-second order model. Meanwhile, adsorption–desorption experiments show that the adsorbent could be recycled a few times and that a high removal efficiency of phosphate from civil wastewater was achieved. Finally, mechanisms show that the adsorption of phosphate by the CMIO@PP (1:3) is mainly caused by electrostatic attraction and ligand exchange.

scholarly journals Preparation of Nano-Porous Carbon-Silica Composites and Its Adsorption Capacity to Volatile Organic Compounds

Processes ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 372 ◽  
Author(s):  
Lipei Fu ◽  
Jiahui Zhu ◽  
Weiqiu Huang ◽  
Jie Fang ◽  
Xianhang Sun ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Volatile Organic Compounds ◽  
Adsorption Capacity ◽  
Organic Compounds ◽  
Retention Rate ◽  
Reaction System ◽  
Carbon Powder ◽  
Volatile Organic ◽  
Adsorption Desorption ◽  
Better Than

Carbon-silica composites with nanoporous structures were synthesized for the adsorption of volatile organic compounds (VOCs), taking tetraethyl orthosilicate (TEOS) as the silicon source and activated carbon powder as the carbon source. The preparation conditions were as follows: the pH of the reaction system was 5.5, the hydrophobic modification time was 50 h, and the dosage of activated carbon was 2 wt%. Infrared spectrum analysis showed that the activated carbon was dispersed in the pores of aerogel to form the carbon-silica composites material. The static adsorption experiments, dynamic adsorption-desorption experiments, and regeneration experiments show that the prepared carbon-silica composites have microporous and mesoporous structures, the adsorption capacity for n-hexane is better than that of conventional hydrophobic silica gel, and the desorption performance is better than that of activated carbon. It still has a high retention rate of adsorption capacity after multiple adsorption-desorption cycles. The prepared carbon-silica composites material has good industrial application prospects in oil vapor recovery, providing a new alternative for solving organic waste gas pollution.

Ferric ion adsorption and electrodesorption by carbon nanotubes and nanofibres films

2009 ◽  
Vol 59 (8) ◽  
pp. 1657-1663 ◽  
Author(s):  
Haibo Li ◽  
Likun Pan ◽  
Yanping Zhang ◽  
Zhuo Sun
Keyword(s):  
Carbon Nanotubes ◽  
Adsorption Process ◽  
Physical Adsorption ◽  
Chemical Vapor ◽  
Ion Adsorption ◽  
Order Model ◽  
First Order ◽  
Monolayer Adsorption ◽  
Pressure Chemical ◽  
Kinetics And Isotherms

Carbon nanotubes and nanofibres (CNTs-CNFs) films have been grown on Ni sheets by low pressure chemical vapor deposition system and show good physical adsorption capability for ferric (Fe3 + ) ions. The studies of adsorption kinetics and isotherms indicate that Fe3 +  adsorption process was regarded as first-order model and followed a Langmuir isotherm indicating monolayer adsorption. The saturated CNTs-CNFs film is easy to be regenerated by electrodesorption with direct voltage applied. The result shows that the combination of adsorption and electrodesorption by CNTs-CNFs is a promising technology to remove the Fe3 +  contamination in solution, which can be further extended to the process of other heavy metal ions.

scholarly journals Preparation of Synthetic Clays to Remove Phosphates and Ibuprofen in Water

Water ◽  
2021 ◽  
Vol 13 (17) ◽  
pp. 2394
Author(s):  
Rosa Devesa-Rey ◽  
Jesús del Val ◽  
Jorge Feijoo ◽  
José González-Coma ◽  
Gonzalo Castiñeira ◽  
...  
Keyword(s):  
Close Agreement ◽  
Adsorption Process ◽  
Intraparticle Diffusion ◽  
Phosphate Adsorption ◽  
Order Model ◽  
Intraparticle Diffusion Model ◽  
First Order ◽  
Pseudo Second Order ◽  
Double Hydroxide ◽  
Phosphate Desorption

The main objective of this study consists in the synthesis of a layered double hydroxide (LDH) clay doped with magnesium and aluminum in order to test the removal of phosphates and ibuprofen in water. Two different LDH composites are assessed: oven-dried (LDHD) and calcined (LDHC). Single adsorptions of phosphate and ibuprofen showed up to 70% and 58% removal in water, when LDHC was used. A poorer performance was observed for LDHD, which presented adsorption efficiencies of 52% and 35%, respectively. The simultaneous removal of phosphate and ibuprofen in water showed that LDHC allows a greater reduction in the concentration of both compounds than LDHD. Phosphate adsorption showed a close agreement between the experimental and theoretical capacities predicted by the pseudo-second-order model, whereas ibuprofen fitted to a first-order model. In addition, phosphate adsorption showed a good fit to an intraparticle diffusion model and to Bangham model suggesting that diffusion into pores controls the adsorption process. No other mechanisms may be involved in ibuprofen adsorption, apart from intraparticle diffusion. Finally, phosphate desorption could recover up to 59% of the initial concentration, showing the feasibility of the recuperation of this compound in the LDH.

scholarly journals Activated Carbon Impregnated by Zero-Valent Iron Nanoparticles (AC/nZVI) Optimized for Simultaneous Adsorption Furfural: Green Synthesis, Regeneration, Characterization, and Adsorption-Desorption Studies

2021 ◽  
Author(s):  
Yousef Rashtbari ◽  
Shirin Afshin ◽  
Asghar Hamzezadeh ◽  
Soumya Ghosh ◽  
Ayoob Rastegar ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Iron Nanoparticles ◽  
Adsorption Process ◽  
Surface Adsorption ◽  
Optimal Conditions ◽  
Solution Ph ◽  
Structure And Morphology ◽  
Carbon Coated ◽  
Zero Valent Iron Nanoparticles ◽  
Adsorption Desorption

Abstract Furfural is an organic aromatic compound that has attracted considerable interest as a potential chemical for the production of biochemical and biofuels. However, furfural has proved to possess ecotoxic effect on the environment and to humans, therefore measures are required to prevent these effects. One of the most widely used methods for eliminating furfural is the surface adsorption process.The present study focused on the structure and morphology of the composite nanoparticles, investigated using FTIR, XRD, BET and FE-SEM techniques.Furthermore, the variables of time, solution pH, dosage composite and initial furfural were evaluated. Furfural adsorption was performed by spectrophotometer at a wavelength of 227 nm. The removal efficiency under optimal conditions for furfural (Furfural concentration of 250 mg/L, the composite dose of 4 g/L, the reaction time of 60 min and pH = 7) was 81.46%. In addition, the study of isotherm and adsorption kinetics for furfural showed that the adsorption process follows the Langmuir isotherm and quasi-quadratic kinetics. The qmax of the composite was determined by the Langmuir model of222.22 mg/g. Therefore, the present study exclusively showedthat the activated carbon coated with nZVI nanoparticles used as an effective and environmentally friendly adsorbent for furfural removal from aqueous solutions. Furthermore, this study could possibly have applied for the adsorbtion of other chemical cmpounds such as dyes,metronidazole,aniline.

scholarly journals Batch adsorption studies for ketoprofen removal via Dillenia Indica peel activated carbon

2021 ◽  
Vol 920 (1) ◽  
pp. 012010
Author(s):  
F Fadzail ◽  
M Hasan ◽  
Z Mokhtar ◽  
N Ibrahim ◽  
O S An ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Process ◽  
Chemical Activation ◽  
Batch Adsorption ◽  
Order Model ◽  
Batch Mode ◽  
Adsorbent Dosage ◽  
Pseudo Second Order ◽  
Dillenia Indica ◽  
Experimental Findings

Abstract Removal of ketoprofen using Dillenia Indica peel activated carbon was investigated using batch adsorption at a laboratory scale. Chemical activation method with the aid of phosphoric acid was utilised in preparing the activated carbon. The adsorption experiments were evaluated using various factors which, are initial concentration, adsorbent dosage, and pH of ketoprofen. The optimum condition was determined to be at pH 6 and adsorbent dosage of 0.4 g with a most KTP uptake of 8.354 mg/g. The experimental findings showed that adsorption is favorable at lower pH. Isotherm studies were conducted and the data indicated that Langmuir isotherm was well fitted to the adsorption process and the pseudo-second-order model was more preferable in simulating the kinetic process. In essence, Dillenia Indica peel activated carbon was proven as being a favourable adsorbent for the uptake of ketoprofen in batch mode.

scholarly journals Removal of COD from Groundwater in and Around Industrial Areas - Using Activated Carbon Powder Prepared by Groundnut Foliage and Groundnut Husk

2021 ◽  
Vol 37 (4) ◽  
pp. 922-927
Author(s):  
A. Kistan ◽  
V. Kanchana ◽  
N. K. Geetha ◽  
G. Infant Sujitha
Keyword(s):  
Activated Carbon ◽  
Kinetic Model ◽  
Adsorption Process ◽  
Oxygen Demand ◽  
Carbon Powder ◽  
Order Kinetic ◽  
Industrial Areas ◽  
Sem Image ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The following study explains that the adsorption efficiency of activated carbon used by Groundnut foliage and groundnut husk for the deportation of COD (Chemical Oxygen demand) from groundwater collected from in and around industrial areas of Vellore district was investigated with different activating conditions (Activating agent- KOH, ZnCl2 and H3PO4; Impregnation ratio-1:1,1:2,1:2; and activation temeperture-500-700°C. The activated carbon prepared based on optimized condition has well-developed pore structure and functional groups which is confirmed from SEM image and FTIR analysis respectively. The adsorption equilibrium was reached in 240 min with the isotherm data fitted well in both the model such as Langmuir model and Freundlich’s model indicating chemisorption’s adsorption for the activated carbon. Moreover, the adsorption process was exothermic accompanied by a decrease in irregularity. Furthermore, the adsorption kinetic study indicated that the adsorption process of the prepared sample follows the pseudo-second-order kinetic model compare to the pseudo-first -order kinetic model

scholarly journals Models based on variable fractional digestion rates to describe ruminal in situ digestion

1995 ◽  
Vol 73 (6) ◽  
pp. 793-807 ◽  
Author(s):  
Jaap Van Milgen ◽  
René Baumont
Keyword(s):  
Logistic Model ◽  
Lag Time ◽  
Order Model ◽  
Data Set ◽  
First Order ◽  
Scale Parameters ◽  
Fractional Rate ◽  
Independent Variable ◽  
Efficacy Function

Using a first-order model to describe ruminalin situdigestion implies that the rate of digestion is affected only by the quantity of potentially digestible substrate remaining. Other factors, like the microbial efficacy for digesting substrate, are assumed to be constant. However, microbes are not only the cause but also the result of digestion, being one of the digestion end-products. Two sigmoidal models (a logistic and a Gompertz-like model) were derived from a general digestion function in which the rate of digestion equals the product of the quantity of potentially digestible substrate remaining and a non-constant fractional rate of digestion (microbial efficacy function). The models were compared with a first-order model with a discrete lag time. The logistic model specifically accounted for the conversion of substrate mass to microbial mass, but did not describe microbial migration between the substrate and the ruminal fluid. In contrast, the Gompertz-like model assumed that the change in microbial efficacy was only time-dependent. There was little difference between models in estimates of scale parameters, but the asymptotic microbial efficacy was consistently higher for the logistic model than for the other models. Estimates of discrete lag time in the first-order model were biased towards obtaining values identical to the independent variable. Scale estimators appeared to be more robust than kinetic estimators. Lack-of-fit was present for most model-data set combinations. The similar patterns of residuals between models suggested that a four-parameter model may be insufficient to describe the data. It was concluded that if a four-parameter model is to be used, the model with a discrete lag time would be the least biologically appropriate.

scholarly journals Biocarbon Derived from Opuntia ficus indica for p-Nitrophenol Retention

Processes ◽  
2020 ◽  
Vol 8 (10) ◽  
pp. 1242
Author(s):  
Hanedi Elhleli ◽  
Faten Mannai ◽  
Mongi ben Mosbah ◽  
Ramzi Khiari ◽  
Younes Moussaoui
Keyword(s):  
Activated Carbon ◽  
Fourier Transforms ◽  
Activated Carbons ◽  
Removal Rate ◽  
Order Model ◽  
Opuntia Ficus Indica ◽  
Effects Of Ph ◽  
Pseudo Second Order ◽  
Fourier Transforms Infrared Spectroscopy ◽  
Adsorption Desorption

Activated carbon obtained from Opuntia ficus indica by sodium hydroxide activation was employed for the adsorption of p-nitrophenol from water. The activated carbons obtained were characterized by Fourier transforms infrared spectroscopy, sorption of nitrogen, scanning electron microscopy, and Boehm titration. Effects of pH, contact time, amount of adsorbent, and temperature on the adsorption of p-nitrophenol were studied. Adsorption isotherms were analyzed using Freundlich, Langmuir, Temkin, and Dubinin-Radushkevich models, and the thermodynamic parameters have been determined. The adsorption of p-nitrophenol was spontaneous, exothermic, and propitious at 15 °C and adopted the pseudo-second order model, and the most credible isotherm was Langmuir’s one. The activated carbon used in this work has good p-nitrophenol adsorption characteristics, and the study of the desorption and reuse of this carbon shows that it retains a removal rate greater than 94% after five cycles of adsorption-desorption.

Sign in / Sign up

Export Citation Format

Share Document