scholarly journals Investigation of Cure Reaction, Rheology, Volume Shrinkage and Thermomechanical Properties of Nano-TiO2 Filled Epoxy/DDS Composites

2013 ◽  
Vol 2013 ◽  
pp. 1-17 ◽  
Author(s):  
Jyotishkumar Parameswaranpillai ◽  
Abhilash George ◽  
Jürgen Pionteck ◽  
Sabu Thomas
Keyword(s):  
Mechanical Properties ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Thermomechanical Properties ◽  
Diglycidyl Ether ◽  
Volume Shrinkage ◽  
Heat Of Reaction ◽  
Nano Tio2 ◽  
Cure Reaction ◽  
Good Improvement

The cure reaction, rheology, volume shrinkage, and thermomechanical behavior of epoxy-TiO2 nanocomposites based on diglycidyl ether of bisphenol A cured with 4,4′-diaminodiphenylsulfone have been investigated. The FTIR results show that, at the initial curing stage, TiO2 acts as a catalyst and facilitates the curing. The catalytic effect of TiO2 was further confirmed by the decrease in maximum exothermal peak temperature (DSC results); however, it was also found that the addition of TiO2 decreases the overall degree of cure, as evidenced by lower total heat of reaction of the cured composites compared to neat epoxy. The importance of cure rheology in the microstructure formation during curing was explored by using rheometry. From the PVT studies, it was found that TiO2 decreases the volume shrinkage behavior of the epoxy matrix. The mechanical properties of the cured epoxy composites, such as tensile strength, tensile modulus, flexural strength, flexural modulus, impact strength, and fracture toughness of the polymer composites, were examined. The nanocomposites exhibited good improvement in dimensional, thermal, and mechanical properties with respect to neat cross-linked epoxy system. FESEM micrographs of fractured surfaces were examined to understand the toughening mechanism.

scholarly journals Improving the mechanical properties of polypropylene composites with coconut shell particles

2021 ◽  
Vol 30 ◽  
pp. 263498332110074
Author(s):  
Henry C Obasi ◽  
Uchechi C Mark ◽  
Udochukwu Mark
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Flexural Modulus ◽  
Filler Particle ◽  
Tensile Modulus ◽  
Coconut Shell ◽  
Polypropylene Composites ◽  
Increase With Increase ◽  
Pp Composites ◽  
Shell Particles

Conventional inorganic fillers are widely used as fillers for polymer-based composites. Though, their processing difficulties and cost have demanded the quest for credible alternatives of organic origin like coconut shell fillers. Dried shells of coconut were burnt, ground, and sifted to sizes of 63, 150, 300, and 425 µm. The ground coconut shell particles (CSP) were used as a filler to prepare polypropylene (PP) composites at filler contents of 0% to 40% via injection melt blending process to produce PP composite sheets. The effect of the filler particle size on the mechanical properties was investigated. The decrease in the size of filler (CSP) was found to improve the yield strength, tensile strength, tensile modulus, flexural strength, flexural modulus, and hardness of PP by 8.5 MPa, 15.75 MPa, 1.72 GPa, 7.5 MPa, 100 MPa, and 10.5 HR for 63 µm at 40%, respectively. However, the elongation at break and modulus of resilience of the PP composites were seen to increase with increase in the filler size. Scanning electron microscope analysis showed that fillers with 63 µm particle size had the best distribution and interaction with the PP matrix resulting in enhanced properties.

scholarly journals Dynamic Cure Kinetics and Physical-Mechanical Properties of PEG/Nanosilica/Epoxy Composites

2020 ◽  
Vol 2020 ◽  
pp. 1-10 ◽  
Author(s):  
Haleh Nowruzi Varzeghani ◽  
Iraj Amiri Amraei ◽  
Seyed Rasoul Mousavi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cure Kinetics ◽  
Diglycidyl Ether ◽  
Solid Particles ◽  
Scanning Calorimetry ◽  
Cure Reaction ◽  
Cure Kinetic ◽  
Cure Temperature ◽  
Kinetics Of

This study investigated the effect of polyethylene glycol (PEG) and nanosilica (NS) on the physical-mechanical properties and cure kinetics of diglycidyl ether of bisphenol-A-based epoxy (DGEBA-based EP) resin. For this purpose, tensile and viscometry tests, dynamic mechanical thermal analysis (DMTA), and differential scanning calorimetry (DSC) were carried out under dynamic conditions. The results showed that adding NS and PEG enhances the maximum cure temperature as well as the heat of cure reaction (ΔH) in EP-NS, while it decreases in EP-PEG and EP-PEG-NS. The cure kinetic parameters of EP-PEG-NS were calculated by Kissinger, Ozawa, and KSA methods and compared with each other. The Ea calculated from the Kissinger method (96.82 kJ/mol) was found to be lower than that of the Ozawa method (98.69 kJ/mol). Also, according to the KAS method, the apparent Ea was approximately constant within the 10-90% conversion range. Tensile strength and modulus increased by adding NS, while tensile strength diminished slightly by adding PEG to EP-NS. The glass transition temperature (Tg) was calculated using DMTA which was increased and decreased by the addition of NS and PEG, respectively. The results of the viscometry test showed that the viscosity increased with the presence of both PEG and NS and it prevented the deposition of solid particles.

scholarly journals Effect of MWCNT on Thermal, Mechanical, and Morphological Properties of Polybutylene Terephthalate/Polycarbonate Blends

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
C. P. Rejisha ◽  
S. Soundararajan ◽  
N. Sivapatham ◽  
K. Palanivelu
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Nucleating Agent ◽  
Mechanical Analysis ◽  
Morphological Properties ◽  
Multiwall Carbon Nanotube ◽  
Polybutylene Terephthalate ◽  
The Impact

This paper evaluated the effect of multiwall carbon nanotube (MWCNT) on the properties of PBT/PC blends. The nanocomposites were obtained by melt blending MWCNT in the weight percentages 0.15, 0.3, and 0.45 wt% with PBT/PC blends in a high performance corotating twin screw extruder. Samples were characterized by tensile testing, dynamic mechanical analysis, thermal analysis, scanning electron microscopy, and X-ray diffraction. Concentrations of PBT and PC are optimized as 80 : 20 based on mechanical properties. A small amount of MWCNT shows better increase in the thermal and mechanical properties of the blends of PBT/PC nanocomposite when compared to nanoclays or inorganic fillers. The ultimate tensile strength of the nanocomposites increased from 54 MPa to 85 MPa with addition of MWCNT up to 0.3% and then decreased.The tensile modulus values were increased to about 60% and the flexural modulus was more than about 80%. The impact strength was also improved with 20% PC to about 60% and with 0.15% MWCNT to about 50%. The HDT also improved from 127°C to 205°C. It can be seen from XRD result that the crystallinity of PBT is less affected by incorporating MWCNT. The crystallizing temperature was increased and the MWCNT may act as a strong nucleating agent.

Effects of the Size of Wood Flour on Mechanical Properties of Wood-Plastic Composites

2011 ◽  
Vol 393-395 ◽  
pp. 76-79 ◽  
Author(s):  
Hai Bing Huang ◽  
Hu Hu Du ◽  
Wei Hong Wang ◽  
Hai Gang Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Wood Flour ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Inorganic Filler ◽  
Full Potential ◽  
Wood Plastic Composites ◽  
Plastic Composites

In this article, wood-plastic composites(WPCs) were manufactured with wood flour(80～120mesh、40～80mesh、20～40mesh、10～20mesh) combing with high density polyethylene(HDPE). Effects of the size of wood flour on mechanical properies and density of composites were investigated. Results showed that particle size of wood flour had an important effect on properitiesof WPCs. Change of mesh number had a outstanding effect on flexural modulus, tensile modulus and impact strength, howere, little effect on flexural strength and tensile strength. When mesh number of wood flour changed from 80～120mesh to 10～20mesh,flexural modulus and tensile modulus were respectively enhanced by 42.4% and 28.4%, respectively, and impact strength was decreased by 35.5%.Size of wood flour basically had no effect on density of composite within 10～120mesh. The use of wood flour or fiber as fillers and reinforcements in thermoplastics has been gaining acceptance in commodity plastics applications in the past few years. WPCs are currently experiencing a dramatic increase in use. Most of them are used to produce window/door profiles,decking,railing,ang siding. Wood thermoplastic composites are manufactured by dispering wood fiber or wood flour(WF) into molten plastics to form composite materials by processing techniques such as extrusion,themoforming, and compression or injection molding[1]. WPCs have such advantages[2]：(1)With wood as filler can improve heat resistance and strength of plastic, and wood has a low cost, comparing with inorganic filler, wood has a low density. Wood as strengthen material has a great potential in improving tensile strength and flexural modulus[3]；(2) For composite of same volume, composites with wood as filler have a little abrasion for equipment and can be regenerated；(3)They have a low water absorption and low hygroscopic property, They are not in need of protective waterproof paint, at the same time, composite can be dyed and painted for them own needs；(4)They are superior to wood in resistantnce to crack、leaf mold and termite aspects, composites are the same biodegradation as wood；(5)They can be processed or connected like wood；（6）They can be processed into a lots of complicated shape product by means of extrusion or molding and so on, meanwhile, they have high-efficiency raw material conversion and itself recycle utilization[4]. While there are many sucesses to report in WPCs, there are still some issues that need to be addressed before this technology will reach its full potential. This technology involves two different types of materials: one hygroscopic(biomass) and one hydrophobic(plastic), so there are issues of phase separation and compatibilization[5]. In this paper, Effects of the size of wood powder on mechanical properties of WPCs were studied.

scholarly journals A Study of Physico-Mechanical Properties of Hollow Glass Bubble, Jute Fibre and Rubber Powder Reinforced Polypropylene Compounds with and without MuCell® Technology for Lightweight Applications

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2664
Author(s):  
Yinping Tao ◽  
Srichand Hinduja ◽  
Robert Heinemann ◽  
Anselmo Gomes ◽  
Paulo Jorge Bártolo
Keyword(s):  
Mechanical Properties ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Tensile Yield Strength ◽  
Small Scale ◽  
Scale Production ◽  
Hollow Glass ◽  
Rubber Powder ◽  
Density Reduction ◽  
Base Polymer

Lightweighting is one of the key solutions to reduce the carbon footprint of vehicles. Nowadays, it is still challenging to achieve this target because there is a conflict between the cost and final material performance, as well as the fact that many lightweight solutions are restricted to laboratory or small-scale production. In this work, a commercially feasible strategy was adopted to fabricate materials for lightweight applications. Hollow glass bubbles, jute fibres, and rubber powder were used as fillers with polypropylene as the base polymer. Various samples were fabricated using conventional and MuCell® injection moulding. Their performance was then characterised by their density and morphological, mechanical, and rheological properties. A comparison among hybrid fillers/polypropylene compounds with and without MuCell® technology was investigated. The filler hybridisation resulted in not only a density reduction of up to approximately 10%, but also improved tensile/flexural modulus and strength. The use of MuCell® led to a further reduction in density of roughly 10%. Meanwhile, although some compounds fabricated by MuCell® exhibited some deterioration in their tensile yield strength, tensile modulus, and impact strength, they maintained acceptable mechanical properties for automotive applications.

Mechanical and Interfacial Properties of Hydrolyzed Kevlar Fiber Reinforced Wood Flour/HDPE Composites

2011 ◽  
Vol 221 ◽  
pp. 27-31 ◽  
Author(s):  
Rong Xian Ou ◽  
Qing Wen Wang ◽  
Fei Pin Yuan ◽  
Bao Yu Liu ◽  
Wei Jun Yang
Keyword(s):  
Mechanical Properties ◽  
Wood Flour ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Screw Extruder ◽  
Kevlar Fiber ◽  
Single Screw ◽  
Single Screw Extruder ◽  
Twin Screw ◽  
Matrix Morphology

Hydrolyzed Kevlar fibers (KFs) were compouded into high-density polyethylene (HDPE) with wood flour (WF) by twin-screw/single-screw extruder to investigate the reinforcement effects of KFs on the mechanical properties of conventional WF/HDPE composites. Maleated HDPE (MAPE) was used as a compatibilizer. The mechanical properties significantly improved as the KFs loading increases in the presence of 4% MAPE, such as tensile strength 14.7%, tensile modulus 12.4%, flexural strength 22.2%, flexural modulus 22.4%, and impact strength 41.7% with 2 wt.% KFs compared to WF/HDPE composite with MAPE. The fiber matrix morphology of the interface region in the composites was examined using scanning electron microscopy (SEM).

Mechanical properties of jute fiber reinforced polypropylene composite: Effect of chemical treatment by benzenediazonium salt in alkaline medium

BioResources ◽  
2010 ◽  
Vol 5 (3) ◽  
pp. 1618-1625
Author(s):  
M. Alamgir Kabir ◽  
M. Monimul Huque ◽  
M. Rabiul Islam ◽  
Andrzej K. Bledzki
Keyword(s):  
Mechanical Properties ◽  
Alkaline Medium ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Charpy Impact ◽  
Alkaline Media ◽  
Jute Fiber ◽  
Composite Effect ◽  
Elongation At Break ◽  
Pp Composites

Raw jute fiber was treated with o-hydroxybenzenediazonium salt (o-HBDS) in alkaline media. Raw and modified jute fiber were used to prepare composites by mixing with polypropylene (PP) plastic in different weight fractions (20, 25, 30, and 35%) of jute fiber. The mechanical properties except elongation at break of o-HBDS-treated (in alkaline medium) jute fiber-PP composite were higher than those of PP alone, raw jute fiber-PP composites, and alkali-treated jute fiber-PP composites. The elongation at break of treated jute-PP composite decreased to a large extent as compared to that of PP. The increase of tensile strength, tensile modulus, flexural strength, flexural modulus, and Charpy impact strength were found to be exceptionally high (in some cases ~200%) as compared to those of literature values.

Polypropylene structural foams: Measurements of the core, skin, and overall mechanical properties with evaluation of predictive models

2016 ◽  
Vol 53 (1) ◽  
pp. 25-44 ◽  
Author(s):  
Tarik Sadik ◽  
Caroline Pillon ◽  
Christian Carrot ◽  
José A Reglero Ruiz ◽  
Michel Vincent ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Poisson’S Ratio ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Poisson's Ratio ◽  
Injection Molding Process ◽  
Mixing Rule ◽  
Molding Process ◽  
Plane Shear ◽  
The Core

Relationships for the prediction of various linear mechanical properties of polymeric sandwich foams obtained in injection processes were studied in comparison with shear, tensile, and flexural tests. The samples were obtained by a core-back foam injection molding process that enables one to obtain sandwich materials with dense skins and a foamed core as revealed by the morphological analysis. Tensile, shear, and flexural moduli were investigated for the skin, the core, and the overall foamed structure. In addition, the Poisson’s ratio of the skin was also determined. The core properties were specifically analyzed by machining the samples and removing the skins. Tensile and shear properties of the core can be well described by the Moore equation. The tensile modulus can be calculated by a linear mixing rule with the moduli of the skin and of the core in relation to the thickness of the layers. Shear and flexural moduli are described by a linear mixing rule on the rigidity in agreement with the mechanics of beams. Tensile modulus, out-of-plane shear modulus, and flexural modulus can finally be predicted by the knowledge of only very few data, namely the tensile modulus and Poisson’s ratio of the matrix, the void fraction, and thickness of the core. The equations were proved to be physically meaningful and consistent with each other.

scholarly journals Fully Biodegradable Composites: Thermal, Flammability, Moisture Absorption and Mechanical Properties of Natural Fibre-Reinforced Composites with Nano-Hydroxyapatite

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1145 ◽  
Author(s):  
Pooria Khalili ◽  
Xiaoling LIU ◽  
Zirui ZHAO ◽  
Brina Blinzler
Keyword(s):  
Mechanical Properties ◽  
Moisture Absorption ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Natural Fibre ◽  
Poly Lactic Acid ◽  
Degradation Temperature ◽  
Conventional Film ◽  
Natural Fabrics ◽  
Burn Rate

Natural fibre-reinforced poly(lactic acid) (PLA) laminates were prepared by a conventional film stacking method from PLA films and natural fabrics with a cross ply layup of [0/90/0/90/0/90], followed by hot compression. Natural fibre (NF) nano-hydroxyapatite (nHA) filled composites were produced by the same manufacturing technique with matrix films that had varying concentrations of nHA in the PLA. Their flammability, thermal, moisture absorption and mechanical properties were analysed in terms of the amount of nHA. The flame behavior of neat PLA and composites evaluated by the UL-94 test demonstrated that only the composite containing the highest quantity of nHA (i.e., 40 wt% nHA in matrix) was found to achieve an FH-1 rating and exhibited no recorded burn rate, whereas other composites obtained only an FH-3. The thermal degradation temperature and mass residue were also observed, via thermogravimetric analysis, to increase when increasing concentrations of nHA were added to the NF composite. The tensile strength, tensile modulus and flexural modulus of the neat resin were found to increase significantly with the introduction of flax fibre. Conversely, moisture absorption was found to increase and mechanical properties to decrease with both the presence of NF and increasing concentrations of nHA, and subsequent mechanical properties experienced an obvious reduction.

The effects of wettability, shear strength, and Weibull characteristics of fiber-reinforced poly(lactic acid) composites

2016 ◽  
Vol 36 (5) ◽  
pp. 489-497 ◽  
Author(s):  
John O. Akindoyo ◽  
Mohammad Dalour Hossen Beg ◽  
Suriati Ghazali ◽  
Muhammad Remanul Islam
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Lactic Acid ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Fiber Surface ◽  
Poly Lactic Acid ◽  
Dimethyl Siloxane ◽  
Pull Out ◽  
Relationship Of

Abstract The wettability, interfacial shear strength (IFSS), and Weibull characteristics of oil palm empty fruit bunch (EFB) fibers were studied to evaluate the mechanical properties of EFB- and poly(lactic acid) (PLA)-based composites. The fiber surface was modified through ultrasound and poly(dimethyl siloxane) treatment. The effects of treatment on the morphology, wettability, and structure of fibers were examined by scanning electron microscopy, contact angle, and Fourier transform infrared spectroscopy analysis, respectively. In addition, the Weibull characteristic was used to find the variability in strength of the fibers with respect to surface treatment. Furthermore, the IFSS of EFB fiber-PLA sandwich was investigated through single-fiber pull-out test, using a less strenuous technique. The mechanical properties (tensile strength, tensile modulus, flexural strength, and flexural modulus) of the composites were determined through mechanical testing. A comparison was drawn among the properties of PLA, raw EFB fiber-based composites, and treated EFB fiber-based composites. Additionally, the inter- and intra-relationship of fiber treatment, wettability, and IFSS with the mechanical properties of the PLA/EFB composites were also accounted.

Sign in / Sign up

Export Citation Format

Share Document