scholarly journals Input switched closed-loop single phase SEPIC controlled rectifier with improved performances

2021 ◽  
Vol 11 (1) ◽  
pp. 1
Author(s):  
Md. Shamsul Arifin ◽  
Mohammad Jahangir Alam
Keyword(s):  
Power Factor ◽  
Closed Loop ◽  
Harmonic Distortion ◽  
Input Voltage ◽  
Input Power ◽  
Open Loop ◽  
Dc Power ◽  
Wide Range ◽  
Input Side ◽  
Flow Through

DC power supply has become the driving source for some essential modern applications. Thereby, DC power conditioning has become a significant issue for engineers. Typically used rectifiers associated with a bridge structure is nonlinear in nature. Thereby, the current at input side of the rectifier contains harmonics, which also flow through the power line. The presence of harmonics causes several interruptions and reduce power quality. In this regard, a new close loop SEPIC controlled rectifier is proposed in this paper. The conventional scheme is arranged with a rectifier connected to a DC-DC converter, which is an open loop system. Consequently, such system cannot regulate voltage at load varying condition. The proposed SEPIC controlled rectifier can regulate voltage under load varying condition for a wide range. Additionally, the performance in terms of total harmonic distortion (THD) of input current and power factor at AC side are also within satisfactory range for the closed loop configuration. The controlled rectifier has four operating phases associated with switching states and input voltage polarity. The close loop configuration also incorporates a current and a voltage loop at the feedback path. The comparative studies have been performed among the proposed closed loop construction, the open-loop structure as well as the conventional construction. The effectiveness of the proposed controlled rectifier is verified in terms of THD and input power factor considering the results obtained from simulation.

scholarly journals Input switched closed-loop single phase ĈUK AC to DC converter with improved power quality

2019 ◽  
Vol 10 (3) ◽  
pp. 1373
Author(s):  
Md. Shamsul Arifin ◽  
Nur Mohammad ◽  
Mohammad Ibrahim Khalil ◽  
Mohammad Jahangir Alam
Keyword(s):  
Power Factor ◽  
Single Phase ◽  
Closed Loop ◽  
Harmonic Distortion ◽  
Open Loop ◽  
Current Control ◽  
Control Loop ◽  
Cuk Converter ◽  
Wide Range ◽  
A Current

<span lang="EN-US">A new closed loop AC to DC ĈUK converter is presented in this paper. The conventional ĈUK AC to DC converter has no feedback circuit. Thereby, the output voltage of the converter changes while changing the load. The proposed closed loop converter can regulate voltage with the variation of load over a wide range. Moreover, the power factor and Total Harmonic Distortion (THD) of the supply side current found quite satisfactory from this closed loop ĈUK converter. The converter operates in four steps with a different combination of voltage polarities and switching states. The feedback path consists of a voltage control loop and a current control loop. The closed loop ĈUK converter in this study is compared with the open loop version. Additionally, the comparison is made with the conventional converter of the same topology. The effectiveness in terms of power factor and THD of the proposed converter is verified using simulation results.</span>

scholarly journals Analog Integrated Current Drivers for Bioimpedance Applications: A Review

Sensors ◽  
2019 ◽  
Vol 19 (4) ◽  
pp. 756 ◽  
Author(s):  
Nazanin Neshatvar ◽  
Peter Langlois ◽  
Richard Bayford ◽  
Andreas Demosthenous
Keyword(s):  
Integrated Circuit ◽  
Closed Loop ◽  
Harmonic Distortion ◽  
Open Loop ◽  
Phase Delay ◽  
Output Impedance ◽  
Wide Range ◽  
High Output Impedance ◽  
High Output

An important component in bioimpedance measurements is the current driver, which can operate over a wide range of impedance and frequency. This paper provides a review of integrated circuit analog current drivers which have been developed in the last 10 years. Important features for current drivers are high output impedance, low phase delay, and low harmonic distortion. In this paper, the analog current drivers are grouped into two categories based on open loop or closed loop designs. The characteristics of each design are identified.

A Novel Control Scheme for Power Factor Improvement in Modified Bridgeless Boost Converter

2015 ◽  
Vol 787 ◽  
pp. 833-837
Author(s):  
Tamizhselvan Annamalai ◽  
V. Rajini
Keyword(s):  
Power Factor ◽  
High Efficiency ◽  
Harmonic Distortion ◽  
Input Resistance ◽  
Input Voltage ◽  
Input Power ◽  
Boost Converter ◽  
Green Energy ◽  
Power Losses ◽  
Current Path

In Green Energy technologies like wind energy conversion systems and Domestic applications like SMPS and UPS systems, the input voltage amplitude and input frequency are time varying in nature. Fast-Escalating and extremely challenging high efficiency requirements for AC-DC power supplies for notebooks, desktop computers are to minimize the power losses (Conduction losses). In the conventional rectifiers power losses are more and power factor is poor resulting in loss of efficiency. Normally, the bridgeless topologies, also referred to as dual boost power factor correction (PFC) rectifiers, may reduce the conduction losses by reducing the number of semi-conductor components in the line current path. Power supply units have to make the load compatible with the source. The presence of non-linear load results in poor power factor operation and produces harmonic components in the line. So PFC techniques are necessary to meet harmonic regulations and standards such as IEC 61000-3-2 and IEEE 519. A modified bridgeless topology may be used for such applications. A novel switching controller is developed that regulates the input resistance to a desired value. Hence input power factor is unity and also the total harmonic distortion is controlled to a tolerable limit. In the proposed model, the modified bridgeless boost converter is activated in to a pure resistance mode. Finally the performance of the modified bridgeless boost converter is compared with the existing basic bridgeless boost converter.

scholarly journals Design and Implementation of 150 W AC/DC LED Driver with Unity Power Factor, Low THD, and Dimming Capability

Electronics ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 52 ◽  
Author(s):  
Ngo Thanh Tung ◽  
Nguyen Dinh Tuyen ◽  
Nguyen Minh Huy ◽  
Nguyen Hoai Phong ◽  
Ngo Cao Cuong ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Power Factor ◽  
Electromagnetic Interference ◽  
Light Emitting Diode ◽  
Power Converter ◽  
Input Power ◽  
Led Driver ◽  
Load Range ◽  
Dc Power ◽  
Wide Range

This paper presents the implementation of a two-stage light-emitting diode (LED) driver based on commercial integrated circuits (IC). The presented LED driver circuit topology, which is designed to drive a 150 W LED module, consists of two stages: AC-DC power factor correction (PFC) stage and DC/DC power converter stage. The implementation of the PFC stage uses IC NCP1608, which uses the critical conduction mode to guarantee a unity input power factor with a wide range of input voltages. The DC/DC power converter with soft-switching characteristics for the entire load range uses IC FLS2100XS. Furthermore, the design of an electromagnetic interference (EMI) filter for the LED driver and the dimming control circuit are discussed in detail. The hardware prototype, an LED lighting system, with a rated power of 150 W/32 V from a nominal 220 V/50 Hz AC voltage supply was tested to show the effectiveness of the design. The presented LED driver was tested for street lighting, and the experimental results show that the power factor (PF) was higher than 0.97, the total harmonics distortion (THD) was lower than 7%, and the efficiency was 91.7% at full load. The results prove that the performance of the presented LED driver complies with the standards: IEC61000-3-2 and CIRSP 15:2009.

Comparison of Dc-Dc SEPIC, CUK and Flyback Converters Based LED Drivers

2020 ◽  
pp. 99-107
Author(s):  
Erdal Sehirli
Keyword(s):  
Integrated Circuit ◽  
Closed Loop ◽  
Input Voltage ◽  
Open Loop ◽  
Current Sensor ◽  
Switching Frequency ◽  
Led Driver ◽  
Advantages And Disadvantages ◽  
Led Drivers ◽  
Conduction Mode

This paper presents the comparison of LED driver topologies that include SEPIC, CUK and FLYBACK DC-DC converters. Both topologies are designed for 8W power and operated in discontinuous conduction mode (DCM) with 88 kHz switching frequency. Furthermore, inductors of SEPIC and CUK converters are wounded as coupled. Applications are realized by using SG3524 integrated circuit for open loop and PIC16F877 microcontroller for closed loop. Besides, ACS712 current sensor used to limit maximum LED current for closed loop applications. Finally, SEPIC, CUK and FLYBACK DC-DC LED drivers are compared with respect to LED current, LED voltage, input voltage and current. Also, advantages and disadvantages of all topologies are concluded.

A High Step-up DC-DC Converter Based on the Voltage Lift Technique for Renewable Energy Applications

2021 ◽  
Vol 13 (19) ◽  
pp. 11059
Author(s):  
Shahrukh Khan ◽  
Arshad Mahmood ◽  
Mohammad Zaid ◽  
Mohd Tariq ◽  
Chang-Hua Lin ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Common Ground ◽  
Closed Loop ◽  
Low Voltage ◽  
Renewable Energy Sources ◽  
Input Voltage ◽  
High Gain ◽  
Boost Converter ◽  
Open Loop ◽  
Voltage Gain

High gain DC-DC converters are getting popular due to the increased use of renewable energy sources (RESs). Common ground between the input and output, low voltage stress across power switches and high voltage gain at lower duty ratios are desirable features required in any high gain DC-DC converter. DC-DC converters are widely used in DC microgrids to supply power to meet local demands. In this work, a high step-up DC-DC converter is proposed based on the voltage lift (VL) technique using a single power switch. The proposed converter has a voltage gain greater than a traditional boost converter (TBC) and Traditional quadratic boost converter (TQBC). The effect of inductor parasitic resistances on the voltage gain of the converter is discussed. The losses occurring in various components are calculated using PLECS software. To confirm the performance of the converter, a hardware prototype of 200 W is developed in the laboratory. The simulation and hardware results are presented to determine the performance of the converter in both open-loop and closed-loop conditions. In closed-loop operation, a PI controller is used to maintain a constant output voltage when the load or input voltage is changed.

scholarly journals The Modelling, Simulation and FPGA-Based Implementation for Stepper Motor Wide Range Speed Closed-Loop Drive System Design

Machines ◽  
2018 ◽  
Vol 6 (4) ◽  
pp. 56 ◽  
Author(s):  
Chiu-Keng Lai ◽  
Jhang-Shan Ciou ◽  
Chia-Che Tsai
Keyword(s):  
Embedded System ◽  
High Speed ◽  
Closed Loop ◽  
Open Loop ◽  
Drive System ◽  
Stepper Motor ◽  
Motor Drive ◽  
Digital Controllers ◽  
Loop Control ◽  
Wide Range

Owing to the benefits of programmable and parallel processing of field programmable gate arrays (FPGAs), they have been widely used for the realization of digital controllers and motor drive systems. Furthermore, they can be used to integrate several functions as an embedded system. In this paper, based on Matrix Laboratory (Matlab)/Simulink and the FPGA chip, we design and implement a stepper motor drive. Generally, motion control systems driven by a stepper motor can be in open-loop or closed-loop form, and pulse generators are used to generate a series of pulse commands, according to the desired acceleration/run/deceleration, in order to the drive system to rotate the motor. In this paper, the speed and position are designed in closed-loop control, and a vector control strategy is applied to the obtained rotor angle to regulate the phase current of the stepper motor to achieve the performance of operating it in low, medium, and high speed situations. The results of simulations and practical experiments based on the FPGA implemented control system are given to show the performances for wide range speed control.

scholarly journals PI- Controlled PV Fed Fly Back Converter with Enhanced Dynamic Response

2019 ◽  
Vol 8 (2S11) ◽  
pp. 4031-4034
Keyword(s):  
Steady State ◽  
Dynamic Response ◽  
Rise Time ◽  
Closed Loop ◽  
Input Voltage ◽  
Pi Controller ◽  
Open Loop ◽  
Load Variations ◽  
Simulink Model ◽  
Step Down

Fly back converter is the most popular converter because of its simplicity, low part counts and isolation. It occupies less volume and it saves cost. Fly back converter steps up and step down the voltage with the same polarity. Open loop operation remains insensitive to the input voltage and load variations. Matlab Simulink model for Fly back converter is established using PI controller. Open loop Fly back converter system and closed loop fly back converter systems are simulated and their outcomes are compared. Comparison is done in terms of Rise time ,Settling time and steady state error

Implementation of Single-Phase Two-Switch Midpoint Unidirectional Multilevel Converter System

2018 ◽  
Vol 19 (4) ◽  
Author(s):  
Peethala Rajiv Roy ◽  
P. Parthiban ◽  
B. Chitti Babu
Keyword(s):  
Single Phase ◽  
Pulse Width Modulation ◽  
Low Voltage ◽  
Supply Voltage ◽  
Harmonic Distortion ◽  
Input Voltage ◽  
Open Loop ◽  
Current Control ◽  
Control Technique ◽  
Control Scheme

Abstract This paper deals with implementation of a single-phase three level converter system under low voltage condition. The frequency of the switches is made constant and involves change in ${t_{on}}$ and ${t_{off}}$ duration. For this condition the pulse width modulation control scheme for a single phase three level rectifier is developed to improve the power quality. The hysteresis current control technique is adopted to bring forth three-level PWM on the dc side of the bridge rectifier and to achieve high power factor and low harmonic distortion. Based on the proposed control scheme, the line current is driven to follow the sinusoidal current command which is in phase with the supply voltage. By using three-level voltage pattern the blocking voltage of each power device is clamped to half of the dc link voltage. The simulation and experimental results of 20W converter under low input voltage condition are shown to verify the circuit performance. Open loop simulation and hardware tests are implemented by applying a low voltage of 15 V(rms) on the input side.

Sign in / Sign up

Export Citation Format

Share Document