scholarly journals Silver Matrix Composites - Structure and Properties

2016 ◽  
Vol 61 (1) ◽  
pp. 323-328 ◽  
Author(s):  
J. Wieczorek ◽  
B. Oleksiak ◽  
J. Łabaj ◽  
B. Węcki ◽  
M. Mańka
Keyword(s):  
Mechanical Properties ◽  
Tribological Properties ◽  
Volume Fraction ◽  
Physical And Mechanical Properties ◽  
Plastic Work ◽  
Matrix Composites ◽  
Alloy Matrix ◽  
Ceramic Particles ◽  
Mechanical And Tribological Properties ◽  
The Matrix

Phase compositions of composite materials determine their performance as well as physical and mechanical properties. Depending on the type of applied matrix and the kind, amount and morphology of the matrix reinforcement, it is possible to shape the material properties so that they meet specific operational requirements. In the paper, results of investigations on silver alloy matrix composites reinforced with ceramic particles are presented. The investigations enabled evaluation of hardness, tribological and mechanical properties as well as the structure of produced materials. The matrix of composite material was an alloy of silver and aluminium, magnesium and silicon. As the reinforcing phase, 20-60 μm ceramic particles (SiC, SiO2, Al2O3 and Cs) were applied. The volume fraction of the reinforcing phase in the composites was 10%. The composites were produced using the liquid phase (casting) technology, followed by plastic work (the KOBO method). The mechanical and tribological properties were analysed for plastic work-subjected composites. The mechanical properties were assessed based on a static tensile and hardness tests. The tribological properties were investigated under dry sliding conditions. The analysis of results led to determination of effects of the composite production technology on their performance. Moreover, a relationship between the type of reinforcing phase and the mechanical and tribological properties was established.

Effect of the Matrix and Reinforcement Sizes on the Microstructure, the Physical and Mechanical Properties of Al-SiC Composites

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
M. A. Salem ◽  
I. G. El-Batanony ◽  
M. Ghanem ◽  
Mohamed Ibrahim Abd ElAal
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Volume Fraction ◽  
Physical And Mechanical Properties ◽  
Particle Sizes ◽  
Matrix Composites ◽  
Volume Fractions ◽  
The Matrix ◽  
Sic Composites ◽  
Sic Particle

Different Al-SiC metal matrix composites (MMCs) with a different matrix, reinforcement sizes, and volume fractions were fabricated using ball milling (BM) and powder metallurgy (PM) techniques. Al and Al-SiC composites with different volume fractions were milled for 120 h. Then, the Al and Al-SiC composites were pressed under 125 MPa and finally sintered at 450 °C. Moreover, microsize and combination between micro and nano sizes Al-SiC samples were prepared by the same way. The effect of the Al matrix, SiC reinforcement sizes and the SiC volume fraction on the microstructure evolution, physical and mechanical properties of the produced composites was investigated. The BM and powder metallurgy techniques followed by sintering produce fully dense Al-SiC composite samples with different matrix and reinforcement sizes. The SiC particle size was observed to have a higher effect on the thermal conductivity, electrical resistivity, and microhardness of the produced composites than that of the SiC volume fraction. The decreasing of the Al and SiC particle sizes and increasing of the SiC volume fraction deteriorate the physical properties. On the other hand, the microhardness was enhanced with the decreasing of the Al, SiC particle sizes and the increasing of the SiC volume fraction.

Physical and Mechanical Properties of Composites with Aluminum Alloy Matrix Designed for Metal Forming

2013 ◽  
Vol 212 ◽  
pp. 59-62 ◽  
Author(s):  
Jerzy Myalski ◽  
Jakub Wieczorek ◽  
Adam Płachta
Keyword(s):  
Mechanical Properties ◽  
Metal Forming ◽  
Matrix Material ◽  
Physical And Mechanical Properties ◽  
Mechanical Mixing ◽  
Alloy Matrix ◽  
Segregation Process ◽  
The Matrix ◽  
Glass Carbon ◽  
Properties Of Composites

The change of matrix and usage of the aluminum alloys designed for the metal forming in making the composite suspension allows to extend the processing possibility of this type of materials. The possibility of the metal forming of the composites obtained by mechanical mixing will extend the range of composite materials usage. Applying of the metal forming e.g. matrix forging, embossing, pressing or rolling, will allow to remove the incoherence of the structure created while casting and removing casting failures. In order to avoid the appearance of the casting failures the homogenization conditions need to be changed. Inserting the particles into the matrix influences on the shortening of the composite solidification. The type of the applied particles influenced the sedimentation process and reinforcement agglomeration in the structure of the composite. Opposite to the composites reinforced with one-phase particles applying the fasess mixture (glassy carbon and silicon carbide) triggered significant limitation in the segregation process while casting solidification. Inserting the particles into the AW-AlCu2SiMn matrix lowers the mechanical properties tension and impact value strength. The most beneficial mechanical properties were gained in case of heterofasess composites reinforced with the particle mixture of SiC and glass carbon. The chemical composition of the matrix material (AW-AlCu2SiMn) allows to increase additionally mechanical characteristics by the precipitation hardening reached through heat casting forming.

scholarly journals Effect of Reactive SPS on the Microstructure and Properties of a Dual-Phase Ni-Al Intermetallic Compound and Ni-Al-TiB2 Composite

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5668
Author(s):  
Paweł Hyjek ◽  
Iwona Sulima ◽  
Piotr Malczewski ◽  
Krzysztof Bryła ◽  
Lucyna Jaworska
Keyword(s):  
Intermetallic Compound ◽  
Tribological Properties ◽  
Matrix Material ◽  
Dual Phase ◽  
Compression Tests ◽  
Two Phase ◽  
Alloy Matrix ◽  
Plastic Properties ◽  
Mechanical And Tribological Properties ◽  
The Matrix

As part of the tests, a two-phase NiAl/Ni3Al alloy and a composite based on this alloy with 4 vol% addition of TiB2 were produced by the reactive FAST/SPS (Field Assisted Sintering Technology/Spark Plasma Sintering) sintering method. The sintering process was carried out at 1273 K for 30 s under an argon atmosphere. The effect of reactive SPS on the density, microstructure, and mechanical and tribological properties of a dual-phase Ni-Al intermetallic compound and Ni-Al-TiB2 composite was investigated. Products obtained were characterized by a high degree of sintering (over 99% of the theoretical density). The microstructure of sinters was characterized by a large diversity, mainly in regard to the structure of the dual-phase alloy (matrix). Compression tests showed satisfactory plastic properties of the manufactured materials, especially at high temperature (1073 K). For both materials at room temperature, the compressive strength was over 3 GPa. The stress–strain curves were observed to assume a different course for the matrix material and composite material, including differences in the maximum plastic flow stress depending on the test temperature. The brittle-to-ductile transition temperature was determined to be above 873 K. The research has revealed differences in the physical, mechanical and tribological properties of the produced sinters. However, the differences favourable for the composite were mostly the result of the addition of TiB2 ceramic particles uniformly distributed on grain boundaries.

THE INFLUENCE OF GLASSY CARBON AND ITS FORMS ON TRIBOLOGICAL PROPERTIES OF ALUMINIUM MATRIX COMPOSITES

Tribologia ◽  
2019 ◽  
Vol 285 (3) ◽  
pp. 79-87 ◽  
Author(s):  
Jerzy MYALSKI ◽  
Andrzej Posmyk ◽  
Bartosz HEKNER ◽  
Marcin GODZIERZ
Keyword(s):  
Coefficient Of Friction ◽  
Tribological Properties ◽  
Glassy Carbon ◽  
Amorphous Structure ◽  
Matrix Composites ◽  
Alloy Matrix ◽  
Entire Volume ◽  
Carbon Particles ◽  
The Matrix ◽  
The Coefficient Of Friction

Carbon with an amorphous structure was used as a component to modify the tribological properties of engineering plastics. Its construction allows the formation of carbon-based wear products during friction, adhesively bonded to the surface of cooperating machine parts, acting as a solid lubricant. The work compares the tribological properties of two groups of composites with an aluminium alloy matrix in which glassy carbon appeared in the form of particles and an open cell foam fulfilling the role of strengthening the matrix. The use of spatial structures of reinforcement provides, in comparison with the strengthening of particles, homogeneity of carbon distribution in the entire volume of the composite. The tests carried out on a pin-disc tester showed that the use of spatial carbon structures in the composite ensures a greater coefficient of friction stability than when reinforcing with particles, and the coefficient of friction with a small proportion of carbon foams (about 1 wt%) is comparable with the coefficient of friction in the contact with composites containing 5-10% carbon particles in granular form.

Mechanical Properties of Densified Untwisted Carbon Nanotube Yarn / Epoxy Composites

2015 ◽  
Author(s):  
Risa Yoshizaki ◽  
Kim Tae Sung ◽  
Atsushi Hosoi ◽  
Hiroyuki Kawada
Keyword(s):  
Mechanical Properties ◽  
Volume Fraction ◽  
Polymer Matrix Composites ◽  
High Strength ◽  
Matrix Composites ◽  
Specific Strength ◽  
The Matrix ◽  
Cnt Arrays ◽  
Strength And Stiffness ◽  
Long Fibers

Carbon nanotubes (CNTs) have very high specific strength and stiffness. The excellent properties make it possible to enhance the mechanical properties of polymer matrix composites. However, it is difficult to use CNTs as the reinforcement of long fibers because of the limitation of CNT growth. In recent years, a method to spin yarns from CNT forests has developed. We have succeeded in manufacturing the unidirectional composites reinforced with the densified untwisted CNT yarns. The untwisted CNT yarns have been manufactured by drawing CNTs through a die from vertically aligned CNT arrays. In this study, the densified untwisted CNT yarns with a polymer treatment were fabricated. The tensile strength and the elastic modulus of the yarns were improved significantly by the treatment, and they were 1.9 GPa and 140 GPa, respectively. Moreover, the polymer treatment prevented the CNT yarns from swelling due to impregnation of the matrix resin. Finally, the high strength CNT yarn composites which have higher volume fraction than a conventional method were successfully fabricated.

Experimental Investigation of Tensile Properties and Fracture Mechanism of WCP/Cu Composites Reinforced with Different WCP Volume Fraction

2011 ◽  
Vol 415-417 ◽  
pp. 2244-2247 ◽  
Author(s):  
Feng Yan ◽  
Rong Xin Guo ◽  
Hai Ting Xia ◽  
Hai Yu ◽  
Yu Bo Zhang
Keyword(s):  
Mechanical Properties ◽  
Fracture Behavior ◽  
Volume Fraction ◽  
Copper Matrix ◽  
Matrix Composites ◽  
Fracture Surface Morphology ◽  
Test Results ◽  
Tension Tests ◽  
Tensile Performance ◽  
The Matrix

The copper matrix composites reinforced by different WCP volume fraction were fabricated via Vacuum Hot-pressed Sintering technique. The tensile performance and fracture behavior of WCP/Cu composites were studied by uniaxial tension tests and the fracture surfaces were examined by SEM. The test results of mechanical properties show that the WCP/Cu composites exhibit obvious improvement of tensile property comparing with that of the matrix. The fracture surface morphology indicate a trend that the fracture of WCP/Cu composites changes from debonding to cleavage with the increase of the WCP volume fraction.

Processing, Microstructure and Mechanical Properties of SiCp/AZ91 Mg Matrix Composites Fabricated by Squeeze Casting

2007 ◽  
Vol 546-549 ◽  
pp. 499-502
Author(s):  
X. Qiu ◽  
Xiao Jun Wang ◽  
Ming Yi Zheng ◽  
Kun Wu
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Squeeze Casting ◽  
Volume Fraction ◽  
Matrix Alloy ◽  
Matrix Composites ◽  
Magnesium Matrix Composites ◽  
The Matrix ◽  
Az91 Magnesium ◽  
Different Diameters

The fabrication processing, mechanical properties and fracture characters of SiCp/AZ91 magnesium matrix composites fabricated by squeeze casting were investigated. The SiC particles with different diameters (5μm, 20μm and 50μm) were employed as the reinforcement in the composites, the volume fraction of them was 50% in all cases. Experimental results showed that when the size of SiC particle decreased, the tensile properties of the composite increased. The tensile properties of SiCp/AZ91 composite with small particles are controlled by the properties of matrix alloy and the strength of the interface between the matrix and reinforcements, but the composites reinforced by large particles are controlled by the fracture of the particles.

Processing Routes, Mechanical, and Tribological Properties of Light Metal Matrix Nanocomposites

2017 ◽  
pp. 991-1037
Author(s):  
S. Jayalakshmi ◽  
R. Arvind Singh
Keyword(s):  
Tribological Properties ◽  
Metal Matrix ◽  
Base Material ◽  
Light Metal ◽  
Advanced Materials ◽  
Matrix Composites ◽  
Metal Matrix Nanocomposites ◽  
Mechanical And Tribological Properties ◽  
The Matrix ◽  
Matrix Nanocomposites

The chapter highlights the various processing/synthesizing routes of Light Metal Matrix Nanocomposites (LMMNCs), their microstructural characteristics, mechanical behaviour, and tribological properties. LMMNCs are advanced materials, in which nano-sized ceramic particles are reinforced into Al/Mg matrices. In conventional Metal Matrix Composites (MMCs), the incorporation of micron sized reinforcements in the matrix usually results in a considerable improvement in hardness and ultimate strength when compared to the unreinforced base material. However, most of these composites do not show plastic deformation (little or no yield) and exhibit drastic reduction in ductility. This poses a major limitation for MMCs to be used in real-time applications. In order to overcome this drawback, Al/Mg composites with nano-scale reinforcements have been developed. Based on numerous research works, it has been established that LMMNCs are better materials that possess superior properties, wherein both strength and ductility improvements along with excellent wear resistance can be achieved.

scholarly journals Mechanical and Tribological Properties of Metal Matrix Composites Reinforced with Short Carbon Fibre

2014 ◽  
Vol 59 (2) ◽  
pp. 707-711 ◽  
Author(s):  
M. Łągiewka
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Carbon Fibre ◽  
Metal Matrix Composites ◽  
Tribological Properties ◽  
Metal Matrix ◽  
Matrix Alloy ◽  
Matrix Composites ◽  
Mechanical And Tribological Properties ◽  
Short Carbon

Abstract The paper constitutes the culmination of the foregoing investigations concerning the influence of short carbon fibre on the enhancement of AlMg10 alloy properties. The presented work brings forward the results of examinations of mechanical and tribological properties of metal matrix composites (MMCs) based on this alloy. Composites were produced by two methods: either by gravity casting or by squeeze casting in semi-solid state of a composite suspension previously obtained through mixing of its components. The volume fraction of the reinforcing phase varied and took the value of 5, or 10, or finally 15 vol. %. Specimens cut out of the experimental castings were examined with respect both to their mechanical properties, i.e. the tensile strength and unit elongation, and to their tribological behaviour. A series of examinations of the mechanical properties proved a slight increase in tensile strength and a minor decrease in unit elongation of the examined composite materials both for gravity cast and squeeze cast specimens, as compared with the properties of pure matrix alloy. The introduction of short carbon fibre into the matrix alloy resulted also in the increased abrasive wear resistance of the examined composites in comparison to the non-reinforced matrix.

Sign in / Sign up

Export Citation Format

Share Document