Effect of High Pressure Heat Treatment on Microstructures and Micro-mechanical Properties of CuZn Alloy

2014 ◽  
Vol 33 (4) ◽  
pp. 339-344 ◽  
Author(s):  
Yuhui Wang ◽  
Jun Zhao ◽  
Jianhua Liu ◽  
Ruijun Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Pressure ◽  
Elastic Modulus ◽  
Friction Coefficient ◽  
Recovery Rate ◽  
Elastic Recovery ◽  
Modulus Ratio ◽  
Before And After ◽  
Cuzn Alloy

AbstractThe hardness, elastic modulus, and friction coefficient of the CuZn alloy before and after treatment at 700 °C and 3 GPa for 10 mins were measured by nanoindenter. Effects of high pressure heat treatment on its microstructure and micro-mechanical properties were discussed. The results show that high pressure heat treatment can refine the microstructures of the CuZn alloy, and its hardness, elastic modulus, ratio of hardness, and elastic recovery rate after the 3 GPa treatment increased by 15.44 %, 4.89 %, 8.82 % and 35.90 %, respectively. And the friction coefficient is also decreased.

scholarly journals Mechanical properties of ultra-high pressure sintered sphene (CaTiSiO5)

2016 ◽  
Vol 10 (4) ◽  
pp. 295-298
Author(s):  
Eranezhuth Awin ◽  
Branko Matovic ◽  
Jelena Maletaskic ◽  
Vladimir Urbanovich ◽  
Ravi Kumar
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
High Pressure ◽  
Elastic Modulus ◽  
High Pressures ◽  
Elastic Recovery ◽  
Maximum Load ◽  
Indentation Hardness ◽  
Ultra High Pressure ◽  
Indentation Crack

The investigation of nano-mechanical properties of sphene sintered under ultra-high pressures in the order of 4GPa is done using indentation techniques. An indentation hardness of 6.6GPa and reduced elastic modulus of 112.3GPa is reported at maximum load of 7mN. The material exhibits a high elastic recovery (~59.1%) and the nature of deformation mechanism has been comprehended from the plastic work ratio. In addition, the fracture toughness of the material is also evaluated using indentation crack length method.

Effects of Cryogenic Treatment on Micro-Mechanical Properties of a Cu-Al Alloy

2012 ◽  
Vol 562-564 ◽  
pp. 196-199 ◽  
Author(s):  
Lai Lei Wu ◽  
Lin Liu ◽  
Mai Shun Qi ◽  
Jian Hua Liu ◽  
Rui Jun Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Applied Load ◽  
Elastic Recovery ◽  
Cryogenic Treatment ◽  
Optical Microscope ◽  
Indentation Creep ◽  
Testing System ◽  
Al Alloy ◽  
Before And After

After heat treatment at 800°C for 15min, a Cu-Al alloy was cryogenic treated at -196°C for 30min, the micro-mechanical properties of the Cu-Al alloy before and after cryogenic treatment were measured by nanometer mechanical testing system and the microstructure of the Cu-Al alloy were also analyzed by optical microscope, SEM/EDS and XRD. On the basis of that, the effects of cryogenic treatment on micro-mechanical properties of the Cu-Al alloy were investigated. The results show that the cryogenic treatment can refine the grains, and increase the hardness, elastic modulus, elastic recovery rate and ratio of hardness to modulus of the Cu-Al alloy. As a result, cryogenic treatment can improve the ability to resist applied load and anti-indentation creep effectively.

Microstructure and Mechanical Properties of Ti-6Al-4V Manufactured by SLM

2015 ◽  
Vol 651-653 ◽  
pp. 677-682 ◽  
Author(s):  
Anatoliy Popovich ◽  
Vadim Sufiiarov ◽  
Evgenii Borisov ◽  
Igor Polozov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Phase Composition ◽  
Mechanical Behavior ◽  
Ductile Fracture ◽  
Elevated Temperatures ◽  
Initial Material ◽  
Laser Melting ◽  
Microstructure And Mechanical Properties ◽  
Before And After

The article presents results of a study of phase composition and microstructure of initial material and samples obtained by selective laser melting of titanium-based alloy, as well as samples after heat treatment. The effect of heat treatment on microstructure and mechanical properties of specimens was shown. It was studied mechanical behavior of manufactured specimens before and after heat treatment at room and elevated temperatures as well. The heat treatment allows obtaining sufficient mechanical properties of material at room and elevated temperatures such as increase in ductility of material. The fractography of samples showed that they feature ductile fracture with brittle elements.

scholarly journals Effect of growth conditions on the mechanical properties of lanthanum-gallium tantalate crystals

2020 ◽  
Vol 6 (2) ◽  
pp. 65-70
Author(s):  
Mark V. Weintraub ◽  
Nina S. Kozlova ◽  
Evgeniya V. Zabelina ◽  
Mikhail I. Petrzhik
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Elastic Recovery ◽  
Growth Conditions ◽  
Piezoelectric Response ◽  
Instrumented Indentation ◽  
Recovery Coefficient ◽  
Hardness Tester ◽  
Growth Atmosphere ◽  
Oxygen Addition

The effect of growth conditions, anisotropy and polarity of specimens on the mechanical properties of lanthanum-gallium tantalate La3Ta0.5Ga5.5O14 single crystals grown in different atmospheres (argon (Ar), argon with oxygen addition (Ar+(<2%)O2 and Ar+(2%)O2) and air) was studied. The test specimens for the measurements were cut perpendicularly to a 3rd order axis (Z cuts) and in polar directions perpendicular to a 2nd order axis (Y cuts). The polarity of the Y cut specimens was tested by piezoelectric response. The brittleness was evaluated by microindentation at 3, 5, 10 and 25 g loads. The brittleness proved to show itself at a 5 g and the higher loads regardless of growth atmosphere. Therefore microhardness tests were done at loads of within 3 g. The microhardness HV of the specimens was measured with an DM 8B Affri microhardness tester by Vickers methods. The hardness H, elastic modulus E and elastic recovery coefficient R were measured with a Berkovich pyramid on a CSM Nano-Hardness Tester using the instrumented indentation (nanoindentation) method. Growth atmosphere was shown to affect the mechanical properties of lanthanum-gallium tantalate crystals: crystals grown in an oxygen-free argon atmosphere had the lowest microhardness, hardness, elastic modulus and elastic recovery coefficient. The lowest microhardness was detected in Z cut specimens regardless of growth atmosphere. The mechanical properties of polar Y cuts proved to be anisotropic: the microhardness, hardness, elastic modulus and elastic recovery coefficient of these cuts were lower for positive cuts than for negative ones regardless of growth atmosphere. Y and Z cut langatate specimens grown in argon with less than two percent oxygen exhibited strong elastic modulus and elastic recovery coefficient anisotropy.

scholarly journals Effect of Mo, V and Zr on the microstructure and mechanical properties of Ti2AlNb alloys

2020 ◽  
Vol 321 ◽  
pp. 08003
Author(s):  
Yujun Du ◽  
Xianghong Liu ◽  
Jinshan Li ◽  
Wenzhong Luo ◽  
Yongsheng He ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Melting Process ◽  
Phase Region ◽  
Arc Furnace ◽  
Micro Hardness ◽  
Β Phase ◽  
Before And After ◽  
B2 Phase ◽  
O Phase

Small button ingots of Ti2AlNb alloys with different contents of Mo, V and Zr were melted by vacuum non-consumable arc furnace. Due to the rapid cooling rate during melting process, only β grains without precipitation were observed in most of the button ingots and no regular phenomenon was found. However, when the samples were heated to β phase region and then furnace cooled to room temperate, different morphologies and quantities of primary α phase and second O phase formed from the β grains of different samples. It is suggested that the morphology of α phase was changed from lamellar to quadrilateral with increasing V and the lath O increased with increasing Zr. Besides, the residual β/B2 phase increased with increasing Mo and V. The EDS results showed that Al and Zr were enriched in α phase whereas Nb, Mo and V were enriched in β/B2 phase. The micro-hardness of these samples before and after heat treatment was detected and the micro-hardness increased with increasing Zr and decreasing Mo and V.

Development and Characterization of New Ti-25Ta-Zr Alloys for Biomedical Applications

2021 ◽  
Vol 1016 ◽  
pp. 137-144
Author(s):  
Pedro Akira Bazaglia Kuroda ◽  
Fernanda de Freitas Quadros ◽  
Mycaela Vieira Nascimento ◽  
Carlos Roberto Grandini
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Elastic Modulus ◽  
Biomedical Applications ◽  
Solution Heat Treatment ◽  
High Hardness ◽  
Microstructural Characterization ◽  
Β Phase ◽  
Cp Ti ◽  
Microscopy Techniques

This paper deals with the study of the development, structural and microstructural characterization and, selected mechanical properties of Ti-25Ta-50Zr alloy for biomedical applications. The alloy was melted in an arc furnace and various solution heat treatments were performed to analyze the influence of the temperature and time on the structure, microstructure, microhardness and elastic modulus of the samples. The structural and microstructural results, obtained by X-ray diffraction and microscopy techniques, showed that the solution heat treatment performed at high temperatures induces the formation of the β phase, while solution heat treatment performed at low temperatures induces the formation of the α” and ω metastable phases. Regarding the effect of time, samples subjected to heat treatment for 6 hours have only the β phase, indicating that lengthy treatments suppress the α” phase. Regarding the hardness and elastic modulus, the alloy with the α” and ω phases, after treatment performed at a temperature of 500 °C, has a high hardness value and elastic modulus due to the presence of the ω phase that hardens and weakens alloys. The titanium alloys developed in this study have excellent mechanical properties results for use in the orthopedic area, better than many commercial materials such as cp-Ti, stainless steel and Co-Cr alloys.

scholarly journals Effect of heat treatment on the tribological properties of Nickel-Boron electroless coating

2018 ◽  
Vol 27 (47) ◽  
pp. 101
Author(s):  
Sandra Arias ◽  
Maryory Gómez ◽  
Esteban Correa ◽  
Félix Echeverría-Echeverría ◽  
Juan Guillermo Castaño
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Wear Resistance ◽  
Carbon Steel ◽  
Tribological Properties ◽  
Tribological Performance ◽  
Dry Sliding ◽  
Electroless Coating ◽  
Before And After ◽  
Properties Of Materials

Nickel-Boron autocatalytic coatings are widely used in several industries to improve mechanical properties of materials such as hardness and wear resistance. Tribological properties were evaluated in Ni-B autocatalytic coatings deposited on AISI/SAE 1018 carbon steel before and after a heat treatment at 450 °C for one hour. Tribological tests were carried out by dry sliding, using a load of 5 N and a sliding speed of 0.012 m/s, in a homemade ball-on-disk tribometer, which followed ASTM G99 standard. According to the tribological evaluation, the heat treatments applied to Ni-B coatings improved their tribological performance. This research corroborates that by applying an adequate heat treatment, hardness and wear resistance of Ni-B coatings can be improved significantly.

Microstructure and Mechanical Properties of TiB2/ Al-Si Composites Fabricated by TIG Wire and Arc Additive Manufacturing

2019 ◽  
Vol 944 ◽  
pp. 64-72
Author(s):  
Qing Feng Yang ◽  
Cun Juan Xia ◽  
Ya Qi Deng
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Yield Strength ◽  
Filler Wire ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Before And After

Bulky sample was made by using TIG wire and arc additive manufacturing (WAAM) technology, in which Ф1.6 mm filler wire of in-situ TiB2/Al-Si composites was selected as deposition metal, following by T6 heat treatment. The microstructure and mechanical properties of the bulky sample before and after heat treatment were analyzed. Experimental results showed that the texture of the original samples parallel to the weld direction and perpendicular to the weld direction was similar consisting of columnar dendrites and equiaxed crystals. After T6 heat treatment, the hardness of the sample was increased to 115.85 HV from 62.83 HV, the yield strength of the sample was 273.33 MPa, the average tensile strength was 347.33 MPa, and the average elongation after fracture was 7.96%. Although pore defects existed in the fracture, yet the fracture of the sample was ductile fracture.

Ageing Effect on Mechanical Properties of Machined Nanostructures

2013 ◽  
Vol 683 ◽  
pp. 145-149
Author(s):  
Xing Lei Hu ◽  
Ya Zhou Sun ◽  
Ying Chun Liang ◽  
Jia Xuan Chen
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Md Simulation ◽  
Fracture Strain ◽  
Machining Process ◽  
Ageing Process ◽  
Yield Strain ◽  
Before And After ◽  
Mc Simulation

Monte Carlo (MC) method and molecular dynamics (MD) are combined to analyze the influence of ageing on mechanical properties of machined nanostructures. Single crystal copper workpiece is first cut in MD simulation, and then the machined workpiece is used in MC simulation of ageing process, finally the tensile mechanical properties of machined nanostructures before and after ageing are investigated by MD simulation. The results show that machining process and ageing have obvious influence of tensile mechanical properties. After machining, the yield strength, yield strain, fracture strain and elastic modulus reduce by 36.02%, 28.86%, 20.79% and 7.16% respectively. However, the yield strength, yield strain and elastic modulus increase by 4.84%, 1.41% and 1.02% respectively, fracture strain reduce by 24.53% after ageing process. To research the ageing processes of machined nanostructures by MC simulation is both practical and meaningful.

Experimental Investigation into the Influences of Weathering on the Mechanical Properties of Sedimentary Rocks

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Xiaoshuang Li ◽  
Yingchun Li ◽  
Saisai Wu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Friction Coefficient ◽  
Uniaxial Compression ◽  
Sedimentary Rocks ◽  
Uniaxial Tensile ◽  
Mechanical Parameters ◽  
Uniaxial Tensile Strength ◽  
Weathering Grades

The time-dependent behaviors of the sedimentary rocks which refer to the altering of the mechanical and deformable properties of rock elements in the long-term period are of increasing importance in the investigation of the failure mechanism of the rock strata in underground coal mines. In order to obtain the accurate and reliable mechanical parameters of the sedimentary rocks at different weathering grades, the extensive experimental programs including the Brazilian splitting test, uniaxial compression tests, and direct shear tests have been carried out on the specimens that exposed to the nature environments at different durations. The correlation between the weathering grades and mechanical parameters including uniaxial tensile strength, uniaxial compression strength, elastic modulus, Poisson’s ratio, cohesion, and friction coefficient was proposed. The obtained results suggested that uniaxial tensile strength, uniaxial compressive strength, elastic modulus, and cohesion dramatically decreased with increasing weathering time, characterized as the negative exponential relationship in general. The influences of various weathering grades on fracture behavior of the rock specimens were discussed. The cumulative damage of the rock by the weathering time decreased the friction coefficient of the specimens which led to the initiation and propagation of microcrack within the rock at lower stress conditions. The obtained results improved the understanding of the roles of weathering on the mechanical properties of sedimentary rocks, which is helpful in the design of the underground geotechnical structures.

Sign in / Sign up

Export Citation Format

Share Document