Improving Car Fuel Efficiency by Optimising Transmission Parameters

2019 ◽  
Vol 16 (3) ◽  
pp. 7019-7033
Author(s):  
S. A. Gorozhankin ◽  
A. D. Bumaga ◽  
N. V. Savenkov
Keyword(s):  
Power Unit ◽  
Fuel Efficiency ◽  
Experimental Studies ◽  
Engine Performance ◽  
Operating Conditions ◽  
Natural Conditions ◽  
The Road ◽  
Operating Modes ◽  
Transmission Parameters ◽  
Driving Cycles

The theoretical and experimental studies of the car power unit functioning at unsteady modes have been conducted. The experimental studies have been conducted using the test stand for measuring engine performance. In addition, the measurements of the parameters of the power unit of the category N1 vehicle under natural conditions (the road tests in the modes of standardized driving cycles) have been made. The aim of the work is increasing the fuel efficiency of the vehicles under operating conditions. For this purpose, the transmission parameters have been optimised for the conditions of the vehicle driving in the standardized NEDC and WLTC driving cycles. The research results enable to give recommendations on improving both the design of the power unit and its operating modes in operation.

Experimental Evaluation of Turbo-Matching Appropriateness of B60J67, B60J68, A58N70 and A58N72 Turbo-Chargers for a Commercial Vehicle Engine

2018 ◽  
Vol 6 (11) ◽  
pp. 71
Author(s):  
Badal Dev Roy ◽  
R. Saravanan
Keyword(s):  
Internal Combustion Engines ◽  
Perfect Match ◽  
Engine Performance ◽  
Operating Conditions ◽  
Data Logger ◽  
Negative Effects ◽  
Road Test ◽  
The Road ◽  
A Charge ◽  
All Speeds

The Turbocharger is a charge booster for internal combustion engines to ensure best engine performance at all speeds and road conditions especially at the higher load.  Random selection of turbocharger may lead to negative effects like surge and choke in the breathing of the engine. Appropriate selection or match of the turbocharger (Turbomatching) is a tedious task and expensive. But perfect match gives many distinguished advantages and it is a one time task per the engine kind. This study focuses to match the turbocharger to desired engine by simulation and on road test. The objective of work is to find the appropriateness of matching of turbochargers with trim 67 (B60J67), trim 68 (B60J68),  trim 70 (A58N70) and trim 72 (A58N72) for the TATA 497 TCIC -BS III engine. In the road-test (data-logger method) the road routes like highway and slope up were considered for evaluation. The operating conditions with respect various speeds, routes and simulated outputs were compared with the help of compressor map.

scholarly journals Simulation Study of the Process of Friction in the Working Elements of a Car Braking System at Different Degrees of Wear

2018 ◽  
Vol 12 (3) ◽  
pp. 221-226 ◽  
Author(s):  
Andrzej Borawski
Keyword(s):  
Simulation Study ◽  
Friction Pair ◽  
Experimental Studies ◽  
Real Life ◽  
Operating Conditions ◽  
Heating Process ◽  
Passenger Cars ◽  
The Road ◽  
Emergency Braking ◽  
Braking System

Abstract Among the many elements of a modern vehicle, the braking system is definitely among the most important ones. Health, and, frequently, life, may rest upon the design and reliability of brakes. The most common friction pair used in passenger cars today is a disc which rotates with the road wheel and a cooperating pair of brake pads. The composite material of the pad results in changing tribological properties as the pad wears, which was demonstrated in experimental studies. The change is also facilitated by the harsh operating conditions of brakes (high and rapid temperature changes, water, etc.). This paper looks into how changing tribology reflects on the heating process of disc and pads during braking. And so a simulation study was conducted, as this method makes it possible to measure temperature in any given point and at any time, which is either impossible or extremely difficult in real life conditions. Finite element method analyses were performed for emergency braking events at various initial speeds of the vehicle reflecting the current road speed limits.

Analysis of Throttle Opening Variation Impact on a Diesel Engine Performance Using Second Law of Thermodynamics

2009 ◽  
Author(s):  
B. B. Sahoo ◽  
U. K. Saha ◽  
N. Sahoo ◽  
P. Prusty
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Fuel Efficiency ◽  
Engine Performance ◽  
Second Law Of Thermodynamics ◽  
Operating Conditions ◽  
Second Law ◽  
Engine Fuel ◽  
Availability Analysis ◽  
Second Law Analysis

The fuel efficiency of a modern diesel engine has decreased due to the recent revisions to emission standards. For an engine fuel economy, the engine speed is to be optimum for an exact throttle opening (TO) position. This work presents an analysis of throttle opening variation impact on a multi-cylinder, direct injection diesel engine with the aid of Second Law of thermodynamics. For this purpose, the engine is run for different throttle openings with several load and speed variations. At a steady engine loading condition, variation in the throttle openings has resulted in different engine speeds. The Second Law analysis, also called ‘Exergy’ analysis, is performed for these different engine speeds at their throttle positions. The Second Law analysis includes brake work, coolant heat transfer, exhaust losses, exergy efficiency, and airfuel ratio. The availability analysis is performed for 70%, 80%, and 90% loads of engine maximum power condition with 50%, 75%, and 100% TO variations. The data are recorded using a computerized engine test unit. Results indicate that the optimum engine operating conditions for 70%, 80% and 90% engine loads are 2000 rpm at 50% TO, 2300 rpm at 75% TO and 3250 rpm at 100% TO respectively.

Diesel engine performance at the intake of the hydrogen&air mixture

2021 ◽  
pp. 119-126
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Fuel Efficiency ◽  
Experimental Studies ◽  
Motor Fuel ◽  
Engine Performance ◽  
Calorific Value ◽  
Hydrocarbon Emissions ◽  
The Difference

The prospects of using hydrogen as a motor fuel are noted. The problems that arise when converting a diesel engine to run on hydrogen are considered. The features of the organization of the working process of enginesrunning on hydrogen are analyzed. A method of supplying a hydrogenair mixture to a diesel engine is investigated. To supply hydrogen to the engine cylinders, it is proposed to use the Leader4M installation developed by TechnoHill Club LLC (Moscow). Experimental studies of a stationary diesel engine of the D245.12 S type with the supply of hydrogen at the inlet obtained at this installation are carried out. At the maximum power mode, the supply of hydrogen from this installation to the inlet of the diesel engine under study was 0.9 % by weight (taking into account the difference in the calorific value of oil diesel fuel and hydrogen). Such a supply of hydrogen in the specified mode made it possible to increase the fuel efficiency of the diesel engine and reduce the smoke content of exhaust gases, carbon monoxide and unburned hydrocarbon emissions. Keywords internal combustion engines; diesel engine; diesel fuel; hydrogen; hydrogenair mixture; fuel efficiency; exhaust gas toxicity indicators

scholarly journals Knock Intensity Distribution and a Stochastic Control Framework for Knock Control

2019 ◽  
Vol 141 (11) ◽  
Author(s):  
Mateos Kassa ◽  
Carrie Hall ◽  
Michael Pamminger ◽  
Thomas Wallner
Keyword(s):  
Lognormal Distribution ◽  
Control Strategies ◽  
Fuel Efficiency ◽  
Probabilistic Approach ◽  
Engine Performance ◽  
Operating Conditions ◽  
Control Approach ◽  
Spark Timing ◽  
Almost All ◽  
Knock Control

Abstract One of the main factors limiting the efficiency of spark-ignited (SI) engines is the occurrence of engine knock. In high temperature and high pressure in-cylinder conditions, the fuel–air mixture auto-ignites creating pressure shock waves in the cylinder. Knock can significantly damage the engine and hinder its performance; as such, conservative knock control strategies are generally implemented which avoid such operating conditions at the cost of lower thermal efficiencies. Significant improvements in the performance of conventional knock controllers are possible if the properties of the knock process are better characterized and exploited in knock controller designs. One of the methods undertaken to better characterize knocking instances is to employ a probabilistic approach, in which the likelihood of knock is derived from the statistical distribution of knock intensity (KI). In this paper, it is shown that KI values at a fixed operating point for single fuel and dual fuel engines are accurately described using a mixed lognormal distribution. The fitting accuracy is compared against those for a randomly generated mixed-lognormally distributed dataset, and shown to exceed a 95% accuracy threshold for almost all of the operating points tested. Additionally, this paper discusses a stochastic knock control approach that leverages the mixed lognormal distribution to adjust spark timing based on KI measurements. This more informed knock control strategy would allow for improvements in engine performance and fuel efficiency by minimizing knock occurrences.

scholarly journals A Numerical Model to Study the Role of Surface Textures at Top Dead Center Reversal in the Piston Ring to Cylinder Liner Contact

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
N. Morris ◽  
R. Rahmani ◽  
H. Rahnejat ◽  
P. D. King ◽  
S. Howell-Smith
Keyword(s):  
Gas Flow ◽  
Fuel Efficiency ◽  
Surface Texturing ◽  
Engine Performance ◽  
Cylinder Liner ◽  
Operating Conditions ◽  
Ic Engine ◽  
Numerical Predictions ◽  
Combined Solution ◽  
Effect Of Surface

Minimization of parasitic losses in the internal combustion (IC) engine is essential for improved fuel efficiency and reduced emissions. Surface texturing has emerged as a method palliating these losses in instances where thin lubricant films lead to mixed or boundary regimes of lubrication. Such thin films are prevalent in contact of compression ring to cylinder liner at piston motion reversals because of momentary cessation of entraining motion. The paper provides combined solution of Reynolds equation, boundary interactions, and a gas flow model to predict the tribological conditions, particularly at piston reversals. This model is then validated against measurements using a floating liner for determination of in situ friction of an engine under motored condition. Very good agreement is obtained. The validated model is then used to ascertain the effect of surface texturing of the liner surface during reversals. Therefore, the paper is a combined study of numerical predictions and the effect of surface texturing. The predictions show that some marginal gains in engine performance can be expected with laser textured chevron features of shallow depth under certain operating conditions.

scholarly journals Optimization of Parameters and Operating Modes of Disc Sowing Device According to Seeding Uniformity Criterion

2018 ◽  
Vol 28 (3) ◽  
pp. 379-388
Author(s):  
Vladimir A. Ovchinnikov ◽  
Mikhail N. Chatkin ◽  
Alena V. Ovchinnikova
Keyword(s):  
Experimental Studies ◽  
Operating Conditions ◽  
Design Parameters ◽  
Optimal Parameters ◽  
Plant Growth And Development ◽  
Important Condition ◽  
Operating Modes ◽  
Favorable Conditions ◽  
Uniformity Criterion

Introduction. When cultivating agricultural crops, it is necessary to take into account the plants’ need for moisture, nutrients, location by area of nutrition, determining illumination, etc. Taking into account the biological characteristics of crops, various methods of sowing are used to create favorable conditions for plant growth and development. An important condition for sowing is the uniform arrangement of seeds along the sulcus, especially in the cultivation of testes of small-seeded cultures. A key role in the uniformity of seeding is provided by the design parameters and kinematic operating conditions of the sowing device. Materials and Methods. To determine the optimal parameters and operating modes of the disk sowing device, methods of factor experiment and multi-criteria optimization were used. Results. Mathematical models of the technological process of sowing seeds were obtained based of experimental studies. Conclusions. To ensure the improvement of the seeding quality of small seeds, the design parameters of the experimental seeder: х4 – is the diameter of the cell; х5 – the number of cells on the disk, will tend to the maximum values. The optimum circumferential speed of the sowing disk should be in the range from 0.127 to 0.192 m/s, and the speed of the machine’s movement is no more than 2 m/s.

scholarly journals Investigation of cycle skipping methods in an engine converted to positive ignition natural gas engine

2021 ◽  
Vol 13 (9) ◽  
pp. 168781402110454
Author(s):  
Erdal Tunçer ◽  
Tarkan Sandalcı ◽  
Yasin Karagöz
Keyword(s):  
Natural Gas ◽  
Fuel Consumption ◽  
Electronic Control Unit ◽  
Engine Performance ◽  
Control Unit ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Specific Fuel Consumption ◽  
Electronic Throttle ◽  
Operating Modes

In this study, a single cylinder of 1.16 L, naturally aspirated engine was converted to a spark ignition engine, which was a diesel engine operating with natural gas as fuel. By placing electronic throttle, electronic ignition module, gas fuel injectors and proximity sensors on the test engine, the engine has been turned into a positive ignition engine that can work with natural gas as fuel, thanks to the electronic control unit developed by our project team. Then, in the study performed, different cycle skipping strategies were experimentally investigated at a constant engine speed of 1565 rpm, in accordance with the generator operating conditions. Engine performance, emissions (CO, HC, and NOx), and combustion characteristics (cylinder pressure, rate of heat release, etc.) of cycle skipping strategies were experimentally investigated with natural gas as fuel in Normal, 3N1S, 2N1S, and 1N1S engine operating modes. According to the results obtained, specific fuel consumption, CO and HC values improved in all cycle skipping operating conditions, except for NOx, but the best results were obtained in 2N1S operating conditions; it was concluded that the specific fuel consumption, CO and HC values improved by 11.19%, 61.89%, and 65.60%, respectively.

scholarly journals CFD Performance Analysis of a Spark Ignition Engine Fueled by Landfill Gas

2014 ◽  
Vol 7 (1) ◽  
pp. 26-33
Author(s):  
Daniel Swain ◽  
S.O. Bade Shrestha
Keyword(s):  
Greenhouse Gas Emission ◽  
Combustion Engine ◽  
Fluid Dynamic ◽  
Fuel Efficiency ◽  
Landfill Gas ◽  
Flame Temperature ◽  
Engine Performance ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Pure Methane

Landfill gas (LFG) that is generated in an anaerobic environment in landfills and consists primarily of methane and carbondioxide with small amount of nitrogen and other non-methane gases, could be collected and used to produce energy either by extracting methane or using the landfill gas directly in an internal combustion engine or a gas turbine. It amounts to be a net-negative greenhouse gas emission process. Carbondioxide component of LFG dilutes the fuel and absorbs some of the heat of combustion, causing reduced flame temperature that decreases NOx emissions and also suppresses knock. A model was developed and validated with the experimental data available in literature, using the computation fluid dynamic (CFD) code, KIVA-4. Various engine performance parameters at various operating conditions were evaluated and the benefits of methane purification and or direct use of LFG as a fuel in the engine scenarios were compared. It was found that landfill gas used directly at higher compression ratios can be used for pure methane fuel with higher fuel efficiency than can be achieved using pure methane fuel only.

scholarly journals Desarrollo y validación de un modelo cero dimensional de dos zonas para el análisis de la combustión en motores de encendido provocado

2018 ◽  
Vol 23 (2) ◽  
pp. 25-33
Author(s):  
Sebastián Heredia Quintana ◽  
Andres David Morales-Rojas
Keyword(s):  
Internal Combustion Engines ◽  
Numerical Models ◽  
Combustion Process ◽  
Experimental Studies ◽  
Engine Performance ◽  
Operating Conditions ◽  
Maximum Pressure ◽  
Rate Maximum ◽  
Experimental Values ◽  
The University

The growth of the automotive fleet in cities and the imminent depletion of traditional hydrocarbon deposits mean that research in the field of internal combustion engines focuses on generating strategies and developing technologies that allow a reduction in fuel consumption and pollutants emissions. The use of numerical models for simulation is an important tool for both researchers and designers as they allow to approach the performance of the engines under certain operating conditions without incurring in the expense involved in experimental studies and allow analyzing multiple phenomena that occur during combustion that are not easily evaluable from experimental measurements. In this study, a zero-dimensional two zones model which separates the combustion chamber into burned and unburned gases was developed seeking to study the combustion process in ignition engines using gaseous renewable fuel (biogas), using the Law of Wiebe and the chemical equilibrium to simulate the combustion process and the Woschni's semi-empirical correlation for heat transfer. The model is calibrated with information obtained from a high compression ratio (15.5: 1) engine of the combustion and thermal machines laboratory of the University of Antioquia. The main variables of combustion and engine performance (heat release rate, maximum pressure, indicated work, among others) were compared with the results of the model, as well as the emissions generated from CO and NO. There are low errors between the experimental values predicted by the model, with errors less than 10% for the main variables, except for the indicated work, with errors of 27%, and errors between 18% and 49% for the generated emissions, obtaining the highest errors as the degree of load of the motor increases.

Sign in / Sign up

Export Citation Format

Share Document