scholarly journals Desarrollo y validación de un modelo cero dimensional de dos zonas para el análisis de la combustión en motores de encendido provocado

2018 ◽  
Vol 23 (2) ◽  
pp. 25-33
Author(s):  
Sebastián Heredia Quintana ◽  
Andres David Morales-Rojas
Keyword(s):  
Internal Combustion Engines ◽  
Numerical Models ◽  
Combustion Process ◽  
Experimental Studies ◽  
Engine Performance ◽  
Operating Conditions ◽  
Maximum Pressure ◽  
Rate Maximum ◽  
Experimental Values ◽  
The University

The growth of the automotive fleet in cities and the imminent depletion of traditional hydrocarbon deposits mean that research in the field of internal combustion engines focuses on generating strategies and developing technologies that allow a reduction in fuel consumption and pollutants emissions. The use of numerical models for simulation is an important tool for both researchers and designers as they allow to approach the performance of the engines under certain operating conditions without incurring in the expense involved in experimental studies and allow analyzing multiple phenomena that occur during combustion that are not easily evaluable from experimental measurements. In this study, a zero-dimensional two zones model which separates the combustion chamber into burned and unburned gases was developed seeking to study the combustion process in ignition engines using gaseous renewable fuel (biogas), using the Law of Wiebe and the chemical equilibrium to simulate the combustion process and the Woschni's semi-empirical correlation for heat transfer. The model is calibrated with information obtained from a high compression ratio (15.5: 1) engine of the combustion and thermal machines laboratory of the University of Antioquia. The main variables of combustion and engine performance (heat release rate, maximum pressure, indicated work, among others) were compared with the results of the model, as well as the emissions generated from CO and NO. There are low errors between the experimental values predicted by the model, with errors less than 10% for the main variables, except for the indicated work, with errors of 27%, and errors between 18% and 49% for the generated emissions, obtaining the highest errors as the degree of load of the motor increases.

Experimental Evaluation of Turbo-Matching Appropriateness of B60J67, B60J68, A58N70 and A58N72 Turbo-Chargers for a Commercial Vehicle Engine

2018 ◽  
Vol 6 (11) ◽  
pp. 71
Author(s):  
Badal Dev Roy ◽  
R. Saravanan
Keyword(s):  
Internal Combustion Engines ◽  
Perfect Match ◽  
Engine Performance ◽  
Operating Conditions ◽  
Data Logger ◽  
Negative Effects ◽  
Road Test ◽  
The Road ◽  
A Charge ◽  
All Speeds

The Turbocharger is a charge booster for internal combustion engines to ensure best engine performance at all speeds and road conditions especially at the higher load.  Random selection of turbocharger may lead to negative effects like surge and choke in the breathing of the engine. Appropriate selection or match of the turbocharger (Turbomatching) is a tedious task and expensive. But perfect match gives many distinguished advantages and it is a one time task per the engine kind. This study focuses to match the turbocharger to desired engine by simulation and on road test. The objective of work is to find the appropriateness of matching of turbochargers with trim 67 (B60J67), trim 68 (B60J68),  trim 70 (A58N70) and trim 72 (A58N72) for the TATA 497 TCIC -BS III engine. In the road-test (data-logger method) the road routes like highway and slope up were considered for evaluation. The operating conditions with respect various speeds, routes and simulated outputs were compared with the help of compressor map.

Effects of Natural Gas Compositions on Engine In-Cylinder Process

2015 ◽  
Vol 1092-1093 ◽  
pp. 498-503
Author(s):  
La Xiang ◽  
Yu Ding
Keyword(s):  
Natural Gas ◽  
Alternative Fuels ◽  
Combustion Process ◽  
Engine Performance ◽  
Maximum Temperature ◽  
Maximum Pressure ◽  
Test Bed ◽  
Promising Alternative ◽  
Natural Gas Engines ◽  
Lower Maximum

Natural gas (NG) is one of the most promising alternative fuels of diesel and petrol because of its economics and environmental protection. Generally the NG engine share the similar structure profile with diesel or petrol engine but the combustion characteristics of NG is varied from the fuels, so the investigation of NG engine combustion process receive more attentions from the researchers. In this paper, a zero-dimensional model on the basis of Vibe function is built in the MATLAB/SIMULINK environment. The model provides the prediction of combustion process in natural gas engines, which has been verified by the experimental data in the NG test bed. Furthermore, the influence of NG composition on engine performance is investigated, in which the in-cylinder maximum pressure and temperature and mean indicated pressure are compared using different type NG. It is shown in the results that NG with higher composition of methane results in lower maximum temperature and mean indicated pressure as well as higher maximum pressure.

Investigating realistic anode off-gas combustion in SOFC/ICE hybrid systems: mini review and experimental evaluation

2021 ◽  
pp. 146808742110583
Author(s):  
Ioannis Nikiforakis ◽  
Zhongnan Ran ◽  
Michael Sprengel ◽  
John Brackett ◽  
Guy Babbit ◽  
...  
Keyword(s):  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Engine Performance ◽  
High Energy ◽  
Operating Conditions ◽  
Compression Ignition ◽  
Case Scenario ◽  
Gas Combustion ◽  
Thermodynamic Conditions ◽  
Decentralized Energy

Solid oxide fuel cells (SOFCs) have been deployed in hybrid decentralized energy systems, in which they are directly coupled to internal combustion engines (ICEs). Prior research indicated that the anode tailgas exiting the SOFC stack should be additionally exploited due to its high energy value, with typical ICE operation favoring hybridization due to matching thermodynamic conditions during operation. Consequently, extensive research has been performed, in which engines are positioned downstream the SOFC subsystem, operating in several modes of combustion, with the most prevalent being homogeneous compression ignition (HCCI) and spark ignition (SI). Experiments were performed in a 3-cylinder ICE operating in the latter modus operandi, where the anode tailgas was assimilated by mixing syngas (H2: 33.9%, CO: 15.6%, CO2: 50.5%) with three different water vapor flowrates in the engine’s intake. While increased vapor content significantly undermined engine performance, brake thermal efficiency (BTE) surpassed 34% in the best case scenario, which outperformed the majority of engines operating under similar operating conditions, as determined from the conducted literature review. Nevertheless, the best performing application was identified operating under HCCI, in which diesel reformates assimilating SOFC anode tailgas, fueled a heavy duty ICE (17:1), and gross indicated thermal efficiency ([Formula: see text]) of 48.8% was achieved, with the same engine exhibiting identical performance when operating in reactivity-controlled compression ignition (RCCI). Overall, emissions in terms of NOx and CO were minimal, especially in SI engines, while unburned hydrocarbons (UHC) were non-existent due to the absence of hydrocarbons in the assessed reformates.

Ethers and esters as alternative fuels for internal combustion engine: A review

2021 ◽  
pp. 146808742110464
Author(s):  
Yang Hua
Keyword(s):  
Alternative Fuels ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Engine Performance ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Future Research ◽  
Particulate Emissions ◽  
Ic Engine

Ether and ester fuels can work in the existing internal combustion (IC) engine with some important advantages. This work comprehensively reviews and summarizes the literatures on ether fuels represented by DME, DEE, DBE, DGM, and DMM, and ester fuels represented by DMC and biodiesel from three aspects of properties, production and engine application, so as to prove their feasibility and prospects as alternative fuels for compression ignition (CI) and spark ignition (SI) engines. These studies cover the effects of ether and ester fuels applied in the form of single fuel, mixed fuel, dual-fuel, and multi-fuel on engine performance, combustion and emission characteristics. The evaluation indexes mainly include torque, power, BTE, BSFC, ignition delay, heat release rate, pressure rise rate, combustion duration, exhaust gas temperature, CO, HC, NOx, PM, and smoke. The results show that ethers and esters have varying degrees of impact on engine performance, combustion and emissions. They can basically improve the thermal efficiency of the engine and reduce particulate emissions, but their effects on power, fuel consumption, combustion process, and CO, HC, and NOx emissions are uncertain, which is due to the coupling of operating conditions, fuel molecular structure, in-cylinder environment and application methods. By changing the injection strategy, adjusting the EGR rate, adopting a new combustion mode, adding improvers or synergizing multiple fuels, adverse effects can be avoided and the benefits of oxygenated fuel can be maximized. Finally, some challenges faced by alternative fuels and future research directions are analyzed.

Diesel engine performance at the intake of the hydrogen&air mixture

2021 ◽  
pp. 119-126
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Fuel Efficiency ◽  
Experimental Studies ◽  
Motor Fuel ◽  
Engine Performance ◽  
Calorific Value ◽  
Hydrocarbon Emissions ◽  
The Difference

The prospects of using hydrogen as a motor fuel are noted. The problems that arise when converting a diesel engine to run on hydrogen are considered. The features of the organization of the working process of enginesrunning on hydrogen are analyzed. A method of supplying a hydrogenair mixture to a diesel engine is investigated. To supply hydrogen to the engine cylinders, it is proposed to use the Leader4M installation developed by TechnoHill Club LLC (Moscow). Experimental studies of a stationary diesel engine of the D245.12 S type with the supply of hydrogen at the inlet obtained at this installation are carried out. At the maximum power mode, the supply of hydrogen from this installation to the inlet of the diesel engine under study was 0.9 % by weight (taking into account the difference in the calorific value of oil diesel fuel and hydrogen). Such a supply of hydrogen in the specified mode made it possible to increase the fuel efficiency of the diesel engine and reduce the smoke content of exhaust gases, carbon monoxide and unburned hydrocarbon emissions. Keywords internal combustion engines; diesel engine; diesel fuel; hydrogen; hydrogenair mixture; fuel efficiency; exhaust gas toxicity indicators

scholarly journals Effect of Fuel and Air Dilution on Syngas Combustion in an Optical SI Engine

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1566 ◽  
Author(s):  
S.D. Martinez-Boggio ◽  
S.S. Merola ◽  
P. Teixeira Lacava ◽  
A. Irimescu ◽  
P.L. Curto-Risso
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Process ◽  
Visible Spectrum ◽  
Propagation Speed ◽  
Fuel Mixture ◽  
Operating Conditions ◽  
Inert Gases ◽  
Pollutant Emissions ◽  
Si Engine ◽  
Lean Burn

To mitigate the increasing concentration of carbon dioxide in the atmosphere, energy production processes must change from fossil to renewable resources. Bioenergy utilization from agricultural residues can be a step towards achieving this goal. Syngas (fuel obtained from biomass gasification) has been proved to have the potential of replacing fossil fuels in stationary internal combustion engines (ICEs). The processes associated with switching from traditional fuels to alternatives have always led to intense research efforts in order to have a broad understanding of the behavior of the engine in all operating conditions. In particular, attention needs to be focused on fuels containing relatively high concentrations of hydrogen, due to its faster propagation speed with respect to traditional fossil energy sources. Therefore, a combustion study was performed in a research optical SI engine, for a comparison between a well-established fuel such as methane (the main component of natural gas) and syngas. The main goal of this work is to study the effect of inert gases in the fuel mixture and that of air dilution during lean fuelling. Thus, two pure syngas blends (mixtures of CO and H2) and their respective diluted mixtures (CO and H2 with 50vol% of inert gases, CO2 and N2) were tested in several air-fuel ratios (stoichiometric to lean burn conditions). Initially, the combustion process was studied in detail by traditional thermodynamic analysis and then optical diagnostics were applied thanks to the optical access through the piston crown. Specifically, images were taken in the UV-visible spectrum of the entire cycle to follow the propagation of the flame front. The results show that hydrogen promotes flame propagation and reduces its distortion, as well as resulting in flames evolving closer to the spark plug. All syngas blends show a stable combustion process, even in conditions of high air and fuel dilution. In the leanest case, real syngas mixtures present a decrease in terms of performance due to significant reduction in volumetric efficiency. However, this condition strongly decreases pollutant emissions, with nitrogen oxide (NOx) concentrations almost negligible.

scholarly journals The use of thermography in the diagnosis of ship piston internal combustion engines

2018 ◽  
Vol 182 ◽  
pp. 01027
Author(s):  
Jan Monieta
Keyword(s):  
Infrared Thermography ◽  
Internal Combustion Engines ◽  
Experimental Studies ◽  
Internal Combustion ◽  
Technical Condition ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Destructive Testing ◽  
Fault State ◽  
Floating Objects

The intensity of infrared radiation emitted by objects depends mainly on their temperature. One of the diagnostic signals may be the temperature field. In infrared thermography, this quantity is used as an indicator of the technical condition of marine objects. The article presents an overview of the use of infrared thermography for the diagnosis mainly of marine piston floating objects and various types of reciprocating internal combustion engines as well as examples of own research results. A general introduction to infrared thermography and common procedures for temperature measurement and non-destructive testing are presented. Experimental research was carried out both in laboratory conditions and in the operating conditions of sea-going vessels. Experimental studies consisted of the presentation of photographs of the same objects made in visible light and the use of infrared thermography. The same objects were also compared, but for different cylinders of the tested internal combustion engines as well as for the up state and fault state. The characteristics of the temperature values at selected points were taken depending on the engine load along with the approximation mathematical models of these dependencies.

Numerical and Experimental Evaluation of a Dual-Fuel Dry-Low-NOx Micromix Combustor for Industrial Gas Turbine Applications

2018 ◽  
Vol 11 (1) ◽  
Author(s):  
Harald H. W. Funke ◽  
Nils Beckmann ◽  
Jan Keinz ◽  
Sylvester Abanteriba
Keyword(s):  
Gas Turbine ◽  
Combustion Process ◽  
Experimental Studies ◽  
Research Process ◽  
Operating Conditions ◽  
Experimental Investigations ◽  
Dual Fuel ◽  
Pure Hydrogen ◽  
Ongoing Research ◽  
Industrial Gas Turbine

Abstract The dry-low-NOx (DLN) micromix combustion technology has been developed originally as a low emission alternative for industrial gas turbine combustors fueled with hydrogen. Currently, the ongoing research process targets flexible fuel operation with hydrogen and syngas fuel. The nonpremixed combustion process features jet-in-crossflow-mixing of fuel and oxidizer and combustion through multiple miniaturized flames. The miniaturization of the flames leads to a significant reduction of NOx emissions due to the very short residence time of reactants in the flame. The paper presents the results of a numerical and experimental combustor test campaign. It is conducted as part of an integration study for a dual-fuel (H2 and H2/CO 90/10 vol %) micromix (MMX) combustion chamber prototype for application under full scale, pressurized gas turbine conditions in the auxiliary power unit Honeywell Garrett GTCP 36-300. In the presented experimental studies, the integration-optimized dual-fuel MMX combustor geometry is tested at atmospheric pressure over a range of gas turbine operating conditions with hydrogen and syngas fuel. The experimental investigations are supported by numerical combustion and flow simulations. For validation, the results of experimental exhaust gas analyses are applied. Despite the significantly differing fuel characteristics between pure hydrogen and hydrogen-rich syngas, the evaluated dual-fuel MMX prototype shows a significant low NOx performance and high combustion efficiency. The combustor features an increased energy density that benefits manufacturing complexity and costs.

Effect of Fuel Injection Pressure and Engine Speed on Performance, Emissions, Combustion, and Particulate Investigations of Gasohols Fuelled Gasoline Direct Injection Engine

2019 ◽  
Vol 142 (4) ◽  
Author(s):  
Nikhil Sharma ◽  
Avinash Kumar Agarwal
Keyword(s):  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Driving Forces ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Gasoline Direct Injection ◽  
Primary Alcohols ◽  
Renewable Fuel

Abstract Fuel availability, global warming, and energy security are the three main driving forces, which determine suitability and long-term implementation potential of a renewable fuel for internal combustion engines for a variety of applications. Comprehensive engine experiments were conducted in a single-cylinder gasoline direct injection (GDI) engine prototype having a compression ratio of 10.5, for gaining insights into application of mixtures of gasoline and primary alcohols. Performance, emissions, combustion, and particulate characteristics were determined at different engine speeds (1500, 2000, 2500, 3000 rpm), different fuel injection pressures (FIP: 40, 80, 120, 160 bars) and different test fuel blends namely 15% (v/v) butanol, ethanol, and methanol blended with gasoline, respectively (Bu15, E15, and M15) and baseline gasoline at a fixed (optimum) spark timing of 24 deg before top dead center (bTDC). For a majority of operating conditions, gasohols exhibited superior characteristics except minor engine performance penalty. Gasohols therefore emerged as serious candidate as a transitional renewable fuel for utilization in the existing GDI engines, without requirement of any major hardware changes.

scholarly journals Thermodynamic modeling of combustion process of the internal combustion engines – an overview

2019 ◽  
Vol 178 (3) ◽  
pp. 27-37 ◽  
Author(s):  
Denys STEPANENKO ◽  
Zbigniew KNEBA
Keyword(s):  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Engine Performance ◽  
Internal Combustion ◽  
Air Pollutant ◽  
Combustion Engines ◽  
Engine Simulation ◽  
Toxic Emissions ◽  
The Moment

The mathematical description of combustion process in the internal combustion engines is a very difficult task, due to the variety of phenomena that occurring in the engine from the moment when the fuel-air mixture ignites up to the moment when intake and exhaust valves beginning open. Modeling of the combustion process plays an important role in the engine simulation, which allows to predict in-cylinder pressure during the combustion, engine performance and environmental impact with high accuracy. The toxic emissions, which appears as a result of fuels combustion, are one of the main environmental problem and as a result the air pollutant regulations are increasingly stringent, what makes the investigation of the combustion process to be a relevant task.

Sign in / Sign up

Export Citation Format

Share Document