Precursor and processing effects on BaPbO3 formation kinetics

2006 ◽  
Vol 21 (3) ◽  
pp. 584-596 ◽  
Author(s):  
Jun-ichi Tani ◽  
Guerman Popov ◽  
Paul R. Mort ◽  
Richard E. Riman
Keyword(s):  
Phase Boundary ◽  
Reaction Temperature ◽  
Formation Rate ◽  
Exothermic Reaction ◽  
Three Dimensional ◽  
Interface Reaction ◽  
Diffusion Controlled ◽  
Wide Range ◽  
Lead Oxides ◽  
Nitrate System

The synthesis of BaPbO3 from a wide range of mixtures containing metalorganic precursors, nitrate precursors, lead oxides, barium oxide and peroxide was investigated, and the kinetics was analyzed using the Johnson–Mehl–Avrami (JMA) equation. It was found that Ba and Pb stearate soaps and Pb oxalate that were used as metalorganic precursors formed BaCO3 and PbO or Pb3O4 after firing at 440 °C. The formation rate of BaPbO3 from a metalorganic precursor system is not higher than that from the conventional BaCO3–PbO system and does not depend on mixing methods or the kinds of metalorganic precursors but instead on the synthesis atmosphere. In the case of the BaCO3–PbO system, the Avrami exponent (n) is ∼1, indicating that the reaction is controlled by the phase-boundary-contraction interface reaction. For the BaO2–PbO2 system, n has two values ∼1 and ∼0.3, depending on the reaction temperature and time, indicating that the reaction is either controlled by the phase-boundary-contraction interface reaction or diffusion-controlled reaction. In the Ba nitrate–Pb nitrate system, phase-pure BaPbO3 is obtained at 550 °C, which is 250 °C lower than in the case of the BaCO3–PbO system. The value of n for the nitrate system is ∼1.5, indicating that the reaction is controlled by a three-dimensional (3D) diffusion-controlled nucleation mechanism. In the BaO–PbO system, the formation of BaPbO3 started at 350 °C by an exothermic reaction and the content of BaPbO3 in the product was ∼40 wt%, which is independent of reaction temperature as well as time in the temperature range of 350–500 °C.

Identification of Elastomers in Tire Sections by Total Thermal Analysis. IV. Innerliner

1975 ◽  
Vol 48 (4) ◽  
pp. 653-660 ◽  
Author(s):  
A. K. Sircar ◽  
T. G. Lamond
Keyword(s):  
Exothermic Reaction ◽  
Minor Component ◽  
Peak Temperature ◽  
Thermal Methods ◽  
Important Conclusion ◽  
Diffusion Controlled ◽  
Wide Range ◽  
Secondary Reactions ◽  
Size Characteristic ◽  
A Minor

Abstract Butyl and halogenated butyls are clearly indicated by both DSC and DTG in nitrogen. Binary NR/CIIR blends are also easily characterized by combined DSC and DTG techniques. In ternary SBR/CIIR/NR blends, only CIIR and NR show up in DTG curves when SBR occurs as a minor component. Minor indication of SBR is obtained from DSC curves. Thermal methods fail to distinguish between BUR and CIIR. In elastomer blends, DTG peak temperatures may vary over a wide range depending on the type of the second elastomer. The NR peak temperature (365°C), for example, is lowered by blending with SBR, BR (345–350°C) or CR (325–348°C). These latter elastomers degrade by exothermic reaction. An increase in peak temperature was observed in association with the polymers which degrade by endothermic reaction (EPDM, 369–374°C; CIIR, 373–377°C). This may be caused by abstraction of heat by the second elastomer in the overall decomposition process. Another important conclusion drawn from the blends studies in this series is that thermal stability of the polymers is not materially affected by the presence of another polymer, thus giving rise to the weight-loss peaks at well-defined temperatures, characteristic of each polymer. Thermooxidative stability, however, is very much dependent on the type and composition of the polymers present. The effect of secondary reactions on the degradation curves is also considerably greater in the oxidizing atmosphere. Thermooxidative degradation is very much dependent on sample size, characteristic of a diffusion-controlled reaction. However, it provides auxiliary evidence for idsntification. Except for SBR/BR blends, which show a single Tg changing with composition, all other elastomer blends show transitions at the respective temperatures, indicating the inherent incompatibility of elastomers. However, a second or third transition is not observed when (a) the proportion of the polymer is too small and (b) Tg'a are too close to each other. Thus, obtaining a single glass transition temperature in a polymer blend is not always a proof of its compatibility, as has been claimed so often.

Turbulent three-dimensional dielectric electrohydrodynamic convection between two plates

2012 ◽  
Vol 696 ◽  
pp. 228-262 ◽  
Author(s):  
A. Kourmatzis ◽  
J. S. Shrimpton
Keyword(s):  
Spatial Data ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Two Dimensions ◽  
Three Dimensions ◽  
Energy Budgets ◽  
Turbulent Regime ◽  
Scalar Flux ◽  
Wide Range ◽  
Scalar Variance

AbstractThe fundamental mechanisms responsible for the creation of electrohydrodynamically driven roll structures in free electroconvection between two plates are analysed with reference to traditional Rayleigh–Bénard convection (RBC). Previously available knowledge limited to two dimensions is extended to three-dimensions, and a wide range of electric Reynolds numbers is analysed, extending into a fully inherently three-dimensional turbulent regime. Results reveal that structures appearing in three-dimensional electrohydrodynamics (EHD) are similar to those observed for RBC, and while two-dimensional EHD results bear some similarities with the three-dimensional results there are distinct differences. Analysis of two-point correlations and integral length scales show that full three-dimensional electroconvection is more chaotic than in two dimensions and this is also noted by qualitatively observing the roll structures that arise for both low (${\mathit{Re}}_{E} = 1$) and high electric Reynolds numbers (up to ${\mathit{Re}}_{E} = 120$). Furthermore, calculations of mean profiles and second-order moments along with energy budgets and spectra have examined the validity of neglecting the fluctuating electric field ${ E}_{i}^{\ensuremath{\prime} } $ in the Reynolds-averaged EHD equations and provide insight into the generation and transport mechanisms of turbulent EHD. Spectral and spatial data clearly indicate how fluctuating energy is transferred from electrical to hydrodynamic forms, on moving through the domain away from the charging electrode. It is shown that ${ E}_{i}^{\ensuremath{\prime} } $ is not negligible close to the walls and terms acting as sources and sinks in the turbulent kinetic energy, turbulent scalar flux and turbulent scalar variance equations are examined. Profiles of hydrodynamic terms in the budgets resemble those in the literature for RBC; however there are terms specific to EHD that are significant, indicating that the transfer of energy in EHD is also attributed to further electrodynamic terms and a strong coupling exists between the charge flux and variance, due to the ionic drift term.

scholarly journals Application of Dendrimers for Treating Parasitic Diseases

Pharmaceutics ◽  
2021 ◽  
Vol 13 (3) ◽  
pp. 343
Author(s):  
Veronica Folliero ◽  
Carla Zannella ◽  
Annalisa Chianese ◽  
Debora Stelitano ◽  
Annalisa Ambrosino ◽  
...  
Keyword(s):  
Drug Delivery ◽  
Water Solubility ◽  
Parasitic Infection ◽  
Three Dimensional ◽  
Medical Knowledge ◽  
High Ratio ◽  
Molecular Volume ◽  
Parasitic Infections ◽  
Parasitic Diseases ◽  
Wide Range

Despite advances in medical knowledge, parasitic diseases remain a significant global health burden and their pharmacological treatment is often hampered by drug toxicity. Therefore, drug delivery systems may provide useful advantages when used in combination with conventional therapeutic compounds. Dendrimers are three-dimensional polymeric structures, characterized by a central core, branches and terminal functional groups. These nanostructures are known for their defined structure, great water solubility, biocompatibility and high encapsulation ability against a wide range of molecules. Furthermore, the high ratio between terminal groups and molecular volume render them a hopeful vector for drug delivery. These nanostructures offer several advantages compared to conventional drugs for the treatment of parasitic infection. Dendrimers deliver drugs to target sites with reduced dosage, solving side effects that occur with accepted marketed drugs. In recent years, extensive progress has been made towards the use of dendrimers for therapeutic, prophylactic and diagnostic purposes for the management of parasitic infections. The present review highlights the potential of several dendrimers in the management of parasitic diseases.

scholarly journals Mapping large-scale-structure evolution over cosmic times

2021 ◽  
Author(s):  
Marta B. Silva ◽  
Ely D. Kovetz ◽  
Garrett K. Keating ◽  
Azadeh Moradinezhad Dizgah ◽  
Matthieu Bethermin ◽  
...  
Keyword(s):  
Galaxy Formation ◽  
Large Scale ◽  
High Redshift ◽  
Formation Rate ◽  
Far Infrared ◽  
Large Scale Structure ◽  
Scale Structure ◽  
Structure Evolution ◽  
Intensity Mapping ◽  
Wide Range

AbstractThis paper outlines the science case for line-intensity mapping with a space-borne instrument targeting the sub-millimeter (microwaves) to the far-infrared (FIR) wavelength range. Our goal is to observe and characterize the large-scale structure in the Universe from present times to the high redshift Epoch of Reionization. This is essential to constrain the cosmology of our Universe and form a better understanding of various mechanisms that drive galaxy formation and evolution. The proposed frequency range would make it possible to probe important metal cooling lines such as [CII] up to very high redshift as well as a large number of rotational lines of the CO molecule. These can be used to trace molecular gas and dust evolution and constrain the buildup in both the cosmic star formation rate density and the cosmic infrared background (CIB). Moreover, surveys at the highest frequencies will detect FIR lines which are used as diagnostics of galaxies and AGN. Tomography of these lines over a wide redshift range will enable invaluable measurements of the cosmic expansion history at epochs inaccessible to other methods, competitive constraints on the parameters of the standard model of cosmology, and numerous tests of dark matter, dark energy, modified gravity and inflation. To reach these goals, large-scale structure must be mapped over a wide range in frequency to trace its time evolution and the surveyed area needs to be very large to beat cosmic variance. Only a space-borne mission can properly meet these requirements.

scholarly journals An Overview on the Rheology, Mechanical Properties, Durability, 3D Printing, and Microstructural Performance of Nanomaterials in Cementitious Composites

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2950
Author(s):  
Hongwei Song ◽  
Xinle Li
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Three Dimensional ◽  
Cementitious Materials ◽  
Research Area ◽  
Cementitious Composites ◽  
Split Tensile Strength ◽  
Contour Crafting ◽  
Wide Range ◽  
Active Research

The most active research area is nanotechnology in cementitious composites, which has a wide range of applications and has achieved popularity over the last three decades. Nanoparticles (NPs) have emerged as possible materials to be used in the field of civil engineering. Previous research has concentrated on evaluating the effect of different NPs in cementitious materials to alter material characteristics. In order to provide a broad understanding of how nanomaterials (NMs) can be used, this paper critically evaluates previous research on the influence of rheology, mechanical properties, durability, 3D printing, and microstructural performance on cementitious materials. The flow properties of fresh cementitious composites can be measured using rheology and slump. Mechanical properties such as compressive, flexural, and split tensile strength reveal hardened properties. The necessary tests for determining a NM’s durability in concrete are shrinkage, pore structure and porosity, and permeability. The advent of modern 3D printing technologies is suitable for structural printing, such as contour crafting and binder jetting. Three-dimensional (3D) printing has opened up new avenues for the building and construction industry to become more digital. Regardless of the material science, a range of problems must be tackled, including developing smart cementitious composites suitable for 3D structural printing. According to the scanning electron microscopy results, the addition of NMs to cementitious materials results in a denser and improved microstructure with more hydration products. This paper provides valuable information and details about the rheology, mechanical properties, durability, 3D printing, and microstructural performance of cementitious materials with NMs and encourages further research.

scholarly journals Polymer cyclization for the emergence of hierarchical nanostructures

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Chaojian Chen ◽  
Manjesh Kumar Singh ◽  
Katrin Wunderlich ◽  
Sean Harvey ◽  
Colette J. Whitfield ◽  
...  
Keyword(s):  
Self Assembly ◽  
Three Dimensional ◽  
Hierarchical Structures ◽  
Structural Similarity ◽  
Vital Role ◽  
Nanomaterial Synthesis ◽  
Wide Range ◽  
Linear Poly ◽  
Polymer Folding ◽  
Dynamics Simulations

AbstractThe creation of synthetic polymer nanoobjects with well-defined hierarchical structures is important for a wide range of applications such as nanomaterial synthesis, catalysis, and therapeutics. Inspired by the programmability and precise three-dimensional architectures of biomolecules, here we demonstrate the strategy of fabricating controlled hierarchical structures through self-assembly of folded synthetic polymers. Linear poly(2-hydroxyethyl methacrylate) of different lengths are folded into cyclic polymers and their self-assembly into hierarchical structures is elucidated by various experimental techniques and molecular dynamics simulations. Based on their structural similarity, macrocyclic brush polymers with amphiphilic block side chains are synthesized, which can self-assemble into wormlike and higher-ordered structures. Our work points out the vital role of polymer folding in macromolecular self-assembly and establishes a versatile approach for constructing biomimetic hierarchical assemblies.

scholarly journals A developmentally descriptive method for quantifying shape in gastropod shells

2020 ◽  
Vol 17 (163) ◽  
pp. 20190721
Author(s):  
J. Larsson ◽  
A. M. Westram ◽  
S. Bengmark ◽  
T. Lundh ◽  
R. K. Butlin
Keyword(s):  
Empirical Studies ◽  
Three Dimensional ◽  
Shell Shape ◽  
Large Set ◽  
Littorina Saxatilis ◽  
Shape Variation ◽  
Gastropod Shell ◽  
Geometric Morphometric ◽  
Wide Range ◽  
Descriptive Method

The growth of snail shells can be described by simple mathematical rules. Variation in a few parameters can explain much of the diversity of shell shapes seen in nature. However, empirical studies of gastropod shell shape variation typically use geometric morphometric approaches, which do not capture this growth pattern. We have developed a way to infer a set of developmentally descriptive shape parameters based on three-dimensional logarithmic helicospiral growth and using landmarks from two-dimensional shell images as input. We demonstrate the utility of this approach, and compare it to the geometric morphometric approach, using a large set of Littorina saxatilis shells in which locally adapted populations differ in shape. Our method can be modified easily to make it applicable to a wide range of shell forms, which would allow for investigations of the similarities and differences between and within many different species of gastropods.

scholarly journals A Review on Biosensors and Recent Development of Nanostructured Materials-Enabled Biosensors

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1109
Author(s):  
Varnakavi. Naresh ◽  
Nohyun Lee
Keyword(s):  
High Surface ◽  
Three Dimensional ◽  
Biological Response ◽  
Volume Ratio ◽  
Recent Decade ◽  
Disease Diagnosis ◽  
Electrical Signal ◽  
Detection Sensitivity ◽  
Wide Range ◽  
Color Tunability

A biosensor is an integrated receptor-transducer device, which can convert a biological response into an electrical signal. The design and development of biosensors have taken a center stage for researchers or scientists in the recent decade owing to the wide range of biosensor applications, such as health care and disease diagnosis, environmental monitoring, water and food quality monitoring, and drug delivery. The main challenges involved in the biosensor progress are (i) the efficient capturing of biorecognition signals and the transformation of these signals into electrochemical, electrical, optical, gravimetric, or acoustic signals (transduction process), (ii) enhancing transducer performance i.e., increasing sensitivity, shorter response time, reproducibility, and low detection limits even to detect individual molecules, and (iii) miniaturization of the biosensing devices using micro-and nano-fabrication technologies. Those challenges can be met through the integration of sensing technology with nanomaterials, which range from zero- to three-dimensional, possessing a high surface-to-volume ratio, good conductivities, shock-bearing abilities, and color tunability. Nanomaterials (NMs) employed in the fabrication and nanobiosensors include nanoparticles (NPs) (high stability and high carrier capacity), nanowires (NWs) and nanorods (NRs) (capable of high detection sensitivity), carbon nanotubes (CNTs) (large surface area, high electrical and thermal conductivity), and quantum dots (QDs) (color tunability). Furthermore, these nanomaterials can themselves act as transduction elements. This review summarizes the evolution of biosensors, the types of biosensors based on their receptors, transducers, and modern approaches employed in biosensors using nanomaterials such as NPs (e.g., noble metal NPs and metal oxide NPs), NWs, NRs, CNTs, QDs, and dendrimers and their recent advancement in biosensing technology with the expansion of nanotechnology.

scholarly journals Modelling H2 and its effects on star formation using a joint implementation of gadget-3 and KROME

2021 ◽  
Vol 504 (2) ◽  
pp. 2325-2345
Author(s):  
Emanuel Sillero ◽  
Patricia B Tissera ◽  
Diego G Lambas ◽  
Stefano Bovino ◽  
Dominik R Schleicher ◽  
...  
Keyword(s):  
Star Formation ◽  
Formation Rate ◽  
Physical Parameters ◽  
Density Profiles ◽  
Star Forming ◽  
Chemical Enrichment ◽  
Numerical Resolution ◽  
Stellar Radiation ◽  
Wide Range ◽  
The Impact

ABSTRACT We present p-gadget3-k, an updated version of gadget-3, that incorporates the chemistry package krome. p-gadget3-k follows the hydrodynamical and chemical evolution of cosmic structures, incorporating the chemistry and cooling of H2 and metal cooling in non-equilibrium. We performed different runs of the same ICs to assess the impact of various physical parameters and prescriptions, namely gas metallicity, molecular hydrogen formation on dust, star formation recipes including or not H2 dependence, and the effects of numerical resolution. We find that the characteristics of the simulated systems, both globally and at kpc-scales, are in good agreement with several observable properties of molecular gas in star-forming galaxies. The surface density profiles of star formation rate (SFR) and H2 are found to vary with the clumping factor and resolution. In agreement with previous results, the chemical enrichment of the gas component is found to be a key ingredient to model the formation and distribution of H2 as a function of gas density and temperature. A star formation algorithm that takes into account the H2 fraction together with a treatment for the local stellar radiation field improves the agreement with observed H2 abundances over a wide range of gas densities and with the molecular Kennicutt–Schmidt law, implying a more realistic modelling of the star formation process.

scholarly journals Pulsed Electromagnetic Cross-Well Exploration for Monitoring Permafrost and Examining the Processes of Its Geocryological Changes

Geosciences ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 60
Author(s):  
Viacheslav Glinskikh ◽  
Oleg Nechaev ◽  
Igor Mikhaylov ◽  
Kirill Danilovskiy ◽  
Vladimir Olenchenko
Keyword(s):  
High Performance ◽  
Geophysical Methods ◽  
Three Dimensional ◽  
High Sensitivity ◽  
Data Interpretation ◽  
Industrial Facilities ◽  
Wide Range ◽  
Vector Finite Element ◽  
A New Technique ◽  
Pulsed Electromagnetic

This paper is dedicated to the topical problem of examining permafrost’s state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we proposed and scientifically substantiated a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings, and constructions.

Sign in / Sign up

Export Citation Format

Share Document