Applicability of Shallow-Impurity Doped Silicon to Proton Flux Sensors Using Stable Particle-Induced Conductivity

1997 ◽  
Vol 487 ◽  
Author(s):  
N. Kishimoto ◽  
H. Amekura ◽  
K. Kono ◽  
C. G. Lee
Keyword(s):  
Signal To Noise Ratio ◽  
High Sensitivity ◽  
Radiation Detectors ◽  
Fast Response ◽  
High Energy ◽  
Proton Flux ◽  
Shallow Impurity ◽  
Impurity Doped ◽  
Impurity Doping ◽  
Radiation Induced

AbstractHigh-energy particles incident to a semiconductor sensitively produce electron-hole pairs and the excited current has been used for radiation detectors. Although semiconductors have advantages such as high sensitivity and fast response, a drawback is weakness in radiation damage. To improve the radiation resistance, effects of shallow-impurity doping was explored for Si. Specimens of CZ-Si doped with P or B were bombarded with 17 MeV protons. The radiation-induced current of doped Si has been evaluated, as a function of proton fluence. The signal of particle-induced conductivity showed a fairly constant response to a proton flux, up to 1015 ions/cm2. The fluence range applicable as Si sensors was extended 103-104 times as much as that of non-doped Si, instead of a lower signal-to-noise ratio. Shallow impurities passivate the deep centers of radiation-induced defects, and the radiation tolerance continues until the pre-existent carriers are exhausted. The tolerant fluence is also usable to detect the integrated fluence, by controlling the initial impurity concentration.

scholarly journals A Novel Type Room Temperature Surface Photovoltage Gas Sensor Device 

2018 ◽  
Author(s):  
Monika Kwoka ◽  
Michal A. Borysiewicz ◽  
Pawel Tomkiewicz ◽  
Anna Piotrowska ◽  
Jacek Szuber
Keyword(s):  
Gas Sensor ◽  
Room Temperature ◽  
Gas Sensing ◽  
Signal To Noise Ratio ◽  
High Sensitivity ◽  
Fast Response ◽  
Surface Photovoltage ◽  
Kelvin Probe ◽  
Sensor Device ◽  
Developed Surface

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO2 with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.

scholarly journals An Electrochemical Sensor Based on a Nitrogen-Doped Carbon Material and PEI Composites for Sensitive Detection of 4-Nitrophenol

Nanomaterials ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 86
Author(s):  
Xue Nie ◽  
Peihong Deng ◽  
Haiyan Wang ◽  
Yougen Tang
Keyword(s):  
Electrochemical Sensor ◽  
Signal To Noise Ratio ◽  
High Sensitivity ◽  
Environmental Water ◽  
Fast Response ◽  
Nitrogen Doped ◽  
Potential Applications ◽  
Good Repeatability ◽  
Nitrogen Doped Carbon ◽  
Optimized Conditions

A glassy carbon electrode (GCE) was modified with nitrogen-doped carbon materials (NC) and polyethyleneimine (PEI) composites to design an electrochemical sensor for detecting 4-nitrophenol (4-NP). The NC materials were prepared by a simple and economical method through the condensation and carbonization of formamide. The NC materials were dispersed in a polyethyleneimine (PEI) solution easily. Due to the excellent properties of NC and PEI as well as their synergistic effect, the electrochemical reduction of the 4-NP on the surface of the NC–PEI composite modified electrode was effectively enhanced. Under the optimized conditions, at 0.06–10 μM and 10–100 μM concentration ranges, the NC–PEI/GCE sensor shows a linear response to 4-NP, and the detection limit is 0.01 μM (the signal-to-noise ratio is three). The reliability of the sensor for the detection of 4-NP in environmental water samples was successfully evaluated. In addition, the sensor has many advantages, including simple preparation, fast response, high sensitivity and good repeatability. It may be helpful for potential applications in detecting other targets.

scholarly journals Accurate spectra for high energy ions by advanced time-of-flight diamond-detector schemes in experiments with high energy and intensity lasers

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Martina Salvadori ◽  
F. Consoli ◽  
C. Verona ◽  
M. Cipriani ◽  
M. P. Anania ◽  
...  
Keyword(s):  
Signal To Noise Ratio ◽  
Time Of Flight ◽  
High Sensitivity ◽  
Thin Foil ◽  
High Energy ◽  
High Signal ◽  
Microwave Range ◽  
Diamond Detector ◽  
Experimental Conditions ◽  
High Energy Ions

AbstractTime-Of-Flight (TOF) methods are very effective to detect particles accelerated in laser-plasma interactions, but they show significant limitations when used in experiments with high energy and intensity lasers, where both high-energy ions and remarkable levels of ElectroMagnetic Pulses (EMPs) in the radiofrequency-microwave range are generated. Here we describe a novel advanced diagnostic method for the characterization of protons accelerated by intense matter interactions with high-energy and high-intensity ultra-short laser pulses up to the femtosecond and even future attosecond range. The method employs a stacked diamond detector structure and the TOF technique, featuring high sensitivity, high resolution, high radiation hardness and high signal-to-noise ratio in environments heavily affected by remarkable EMP fields. A detailed study on the use, the optimization and the properties of a single module of the stack is here described for an experiment where a fast diamond detector is employed in an highly EMP-polluted environment. Accurate calibrated spectra of accelerated protons are presented from an experiment with the femtosecond Flame laser (beyond 100 TW power and ~ 1019 W/cm2 intensity) interacting with thin foil targets. The results can be readily applied to the case of complex stack configurations and to more general experimental conditions.

scholarly journals Using a Scintillation Detector to Detect Partial Discharges

Sensors ◽  
2019 ◽  
Vol 19 (22) ◽  
pp. 4936 ◽  
Author(s):  
Łukasz Nagi ◽  
Michał Kozioł ◽  
Michał Kunicki ◽  
Daria Wotzka
Keyword(s):  
Scintillation Detector ◽  
Power Plants ◽  
Early Stage ◽  
High Sensitivity ◽  
Radiation Energy ◽  
Radiation Detectors ◽  
High Energy ◽  
Partial Discharges ◽  
Non Invasive ◽  
Safety Regulations

This article presents the possibility of using a scintillation detector to detect partial discharges (PD) and presents the results of multi-variant studies of high-energy ionizing generated by PD in air. Based on the achieved results, it was stated that despite a high sensitivity of the applied detector, the accompanying electromagnetic radiation from the visible light, UV, and high-energy ionizing radiation can be recorded by both spectroscopes and a system commonly used to detect radiation. It is also important that the scintillation detector identifies a specific location where dangerous electrical discharges and where the E-M radiation energy that accompanies PD are generated. This provides a quick and non-invasive way to detect damage in insulation at an early stage when it is not visible from the outside. In places where different radiation detectors are often used due to safety regulations, such as power plants or nuclear laboratories, it is also possible to use a scintillation detector to identify that the recorded radiation comes from damaged insulation and is not the result of a failure.

In situ TEM studies of irradiation effects for materials improvement

1991 ◽  
Vol 49 ◽  
pp. 452-453
Author(s):  
Charles W. Allen
Keyword(s):  
Nuclear Reactor ◽  
Austenitic Stainless Steels ◽  
High Energy ◽  
Point Of View ◽  
In Situ Tem ◽  
Irradiation Effects ◽  
Tem Analysis ◽  
Radiation Induced ◽  
Analytical Tools

Irradiation effects studies employing TEMs as analytical tools have been conducted for almost as many years as materials people have done TEM, motivated largely by materials needs for nuclear reactor development. Such studies have focussed on the behavior both of nuclear fuels and of materials for other reactor components which are subjected to radiation-induced degradation. Especially in the 1950s and 60s, post-irradiation TEM analysis may have been coupled to in situ (in reactor or in pile) experiments (e.g., irradiation-induced creep experiments of austenitic stainless steels). Although necessary from a technological point of view, such experiments are difficult to instrument (measure strain dynamically, e.g.) and control (temperature, e.g.) and require months or even years to perform in a nuclear reactor or in a spallation neutron source. Consequently, methods were sought for simulation of neutroninduced radiation damage of materials, the simulations employing other forms of radiation; in the case of metals and alloys, high energy electrons and high energy ions.

Observation of surface morphology by reflection electron holography

1989 ◽  
Vol 47 ◽  
pp. 536-537
Author(s):  
N. Osakabe ◽  
J. Endo ◽  
T. Matsuda ◽  
A. Tonomura
Keyword(s):  
Phase Shift ◽  
Surface Morphology ◽  
High Sensitivity ◽  
High Energy ◽  
Path Difference ◽  
Transmission Mode ◽  
Electron Holography ◽  
Dynamical Process ◽  
High Vertical Resolution ◽  
Amplification Technique

Progress in microscopy such as STM and TEM-TED has revealed surface structures in atomic dimension. REM has been used for the observation of surface dynamical process and surface morphology. Recently developed reflection electron holography, which employes REM optics to measure the phase shift of reflected electron, has been proved to be effective for the observation of surface morphology in high vertical resolution ≃ 0.01 Å.The key to the high sensitivity of the method is best shown by comparing the phase shift generation by surface topography with that in transmission mode. Difference in refractive index between vacuum and material Vo/2E≃10-4 owes the phase shift in transmission mode as shownn Fig. 1( a). While geometrical path difference is created in reflection mode( Fig. 1(b) ), which is measured interferometrically using high energy electron beam of wavelength ≃0.01 Å. Together with the phase amplification technique , the vertivcal resolution is expected to be ≤0.01 Å in an ideal case.

scholarly journals Tin Disulfide-Coated Microfiber for Humidity Sensing with Fast Response and High Sensitivity

Crystals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 648
Author(s):  
Aijie Liang ◽  
Jingyuan Ming ◽  
Wenguo Zhu ◽  
Heyuan Guan ◽  
Xinyang Han ◽  
...  
Keyword(s):  
Humidity Sensor ◽  
Small Diameter ◽  
High Sensitivity ◽  
Large Change ◽  
Small Variation ◽  
Response Speed ◽  
Fast Response ◽  
Tin Disulfide ◽  
Recovery Times ◽  
Response And Recovery

Breath monitoring is significant in assessing human body conditions, such as cardiac and pulmonary symptoms. Optical fiber-based sensors have attracted much attention since they are immune to electromagnetic radiation, thus are safe for patients. Here, a microfiber (MF) humidity sensor is fabricated by coating tin disulfide (SnS2) nanosheets onto the surface of MF. The small diameter (~8 μm) and the long length (~5 mm) of the MF promise strong interaction between guiding light and SnS2. Thus, a small variation in the relative humidity (RH) will lead to a large change in optical transmitted power. A high RH sensitivity of 0.57 dB/%RH is therefore achieved. The response and recovery times are estimated to be 0.08 and 0.28 s, respectively. The high sensitivity and fast response speed enable our SnS2-MF sensor to monitor human breath in real time.

A review on radiation induced nausea and vomiting: “Current management strategies and prominence of radio sensitizers”

2021 ◽  
pp. 107815522110115
Author(s):  
Meenu Vijayan ◽  
Sherin Joseph ◽  
Emmanuel James ◽  
Debnarayan Dutta
Keyword(s):  
Radiation Therapy ◽  
Cell Damage ◽  
Genetic Material ◽  
High Energy ◽  
Concurrent Chemotherapy ◽  
Nausea And Vomiting ◽  
Dose Fractionation ◽  
Psychological State ◽  
Related Factors ◽  
Radiation Induced

Radiations dissipated are high energy waves used mostly as treatment intervention in controlling the unwanted multiplication of cell. About 60%–65% of cancer treatment requires radiation therapy and 40%–80% of radiation therapy causes RINV which are true troublemakers. Radiation therapy (RT) is targeted therapy mostly used to treat early stages of tumour and prevent their reoccurrence. They mainly destroy the genetic material (DNA) of cancerous cells to avoid their unwanted growth and division. The RINV affects the management and quality of life of patients which further reduces the patient outcome. RINV depends on RT related factors (dose, fractionation, irradiation volume, RT techniques) and patient related factors like (gender, health conditions, age, concurrent chemotherapy, psychological state, and tumour stage). RT is an active area of research and there is only limited progress in tackling the RINV crisis. Advanced technological methods are adopted that led to better understanding of total lethal doses. Radiation therapy also affects the immunity system that leads to radiation induced immune responses and inflammation. Radio sensitizers are used to sensitize the tumour cells to radiations that further prevent the normal cell damage from radiation exposure. There is a need for future studies and researches to re-evaluate the data available from previous trials in RINV to make better effective antiemetic regimen. The article focuses on radiation therapy induced nausea and vomiting along with their mechanism of action and treatment strategies in order to have a remarkable patient care.

scholarly journals A Full-Range Flexible and Printed Humidity Sensor Based on a Solution-Processed P(VDF-TrFE)/Graphene-Flower Composite

Nanomaterials ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1915
Author(s):  
Shenawar Ali Khan ◽  
Muhammad Saqib ◽  
Muhammad Muqeet Rehman ◽  
Hafiz Mohammad Mutee Ur Rehman ◽  
Sheik Abdur Rahman ◽  
...  
Keyword(s):  
Active Layer ◽  
Humidity Sensor ◽  
High Reliability ◽  
Full Range ◽  
High Sensitivity ◽  
Fast Response ◽  
Considerable Change ◽  
Relative Humidity Range ◽  
Response And Recovery ◽  
Proportional Relationship

A novel composite based on a polymer (P(VDF-TrFE)) and a two-dimensional material (graphene flower) was proposed as the active layer of an interdigitated electrode (IDEs) based humidity sensor. Silver (Ag) IDEs were screen printed on a flexible polyethylene terephthalate (PET) substrate followed by spin coating the active layer of P(VDF-TrFE)/graphene flower on its surface. It was observed that this sensor responds to a wide relative humidity range (RH%) of 8–98% with a fast response and recovery time of 0.8 s and 2.5 s for the capacitance, respectively. The fabricated sensor displayed an inversely proportional response between capacitance and RH%, while a directly proportional relationship was observed between its impedance and RH%. P(VDF-TrFE)/graphene flower-based flexible humidity sensor exhibited high sensitivity with an average change of capacitance as 0.0558 pF/RH%. Stability of obtained results was monitored for two weeks without any considerable change in the original values, signifying its high reliability. Various chemical, morphological, and electrical characterizations were performed to comprehensively study the humidity-sensing behavior of this advanced composite. The fabricated sensor was successfully used for the applications of health monitoring and measuring the water content in the environment.

scholarly journals Alcohol-based highly conductive polymer for conformal nanocoatings on hydrophobic surfaces toward a highly sensitive and stable pressure sensor

2020 ◽  
Vol 12 (1) ◽  
Author(s):  
Jung Joon Lee ◽  
Srinivas Gandla ◽  
Byeongjae Lim ◽  
Sunju Kang ◽  
Sunyoung Kim ◽  
...  
Keyword(s):  
Pressure Sensor ◽  
Mechanical Stability ◽  
Exchange Process ◽  
Conductive Polymer ◽  
High Sensitivity ◽  
Fast Response ◽  
Pdms Surface ◽  
Practical Applications ◽  
Sensor Applications ◽  
Water Based

Abstract Conformal and ultrathin coating of highly conductive PEDOT:PSS on hydrophobic uneven surfaces is essential for resistive-based pressure sensor applications. For this purpose, a water-based poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) solution was successfully exchanged to an organic solvent-based PEDOT:PSS solution without any aggregation or reduction in conductivity using the ultrafiltration method. Among various solvents, the ethanol (EtOH) solvent-exchanged PEDOT:PSS solution exhibited a contact angle of 34.67°, which is much lower than the value of 96.94° for the water-based PEDOT:PSS solution. The optimized EtOH-based PEDOT:PSS solution exhibited conformal and uniform coating, with ultrathin nanocoated films obtained on a hydrophobic pyramid polydimethylsiloxane (PDMS) surface. The fabricated pressure sensor showed high performances, such as high sensitivity (−21 kPa−1 in the low pressure regime up to 100 Pa), mechanical stability (over 10,000 cycles without any failure or cracks) and a fast response time (90 ms). Finally, the proposed pressure sensor was successfully demonstrated as a human blood pulse rate sensor and a spatial pressure sensor array for practical applications. The solvent exchange process using ultrafiltration for these applications can be utilized as a universal technique for improving the coating property (wettability) of conducting polymers as well as various other materials.

Sign in / Sign up

Export Citation Format

Share Document