Absorber Films of Ag2S and AgBiS2 prepared by Chemical Bath Deposition

2002 ◽  
Vol 730 ◽  
Author(s):  
A. Nuñez Rodriguez ◽  
M.T.S. Nair ◽  
P.K. Nair
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Electrical Conductivity ◽  
Silver Nitrate ◽  
Band Gap ◽  
Chemical Bath Deposition ◽  
Optical Band Gap ◽  
Sodium Thiosulfate ◽  
Xrd Pattern ◽  
Glass Substrates

AbstractAg2S thin films of 90 nm to 300 nm in thickness were deposited at 70°C on glass substrates immersed in a bath mixture containing silver nitrate, sodium thiosulfate and dimethylthiourea. When the films are heated in nitrogen at temperatures 200°C to 400°C, crystallinity is improved and XRD pattern similar to that of acanthite is observed. These films possess electrical conductivity of 10-3 (ohm cm)-1, are photoconductive and exhibit an optical band gap of 1.36 eV. When Ag2S thin film is deposited over a thin film of Bi2S3, also obtained by chemical bath deposition from bismuth nitrate, triethanolamine and thioacetamide, and heated at 300°C to 400°C in nitrogen, a ternary compound, AgBiS2 is formed. This material has an electrical conductivity of 5x10-5 (ohm cm)-1, is photoconductive and possesses optical band gap 0.95 eV.

Characterization of MnS Thin Films Deposited by Chemical Bath Deposition

2019 ◽  
Vol 969 ◽  
pp. 433-438 ◽  
Author(s):  
Dattatraya K. Sonavane ◽  
S.K. Jare ◽  
M.A. Shaikh ◽  
R.V. Kathare ◽  
R.N. Bulakhe
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Band Gap ◽  
Chemical Bath Deposition ◽  
Band Gap Energy ◽  
Sulfur Source ◽  
X Ray Diffraction ◽  
Glass Substrates ◽  
Double Beam

Glass substrates are used to deposit thin films utilizing basic and value effective chemical bath deposition (CBD) technique. The films were prepared from the mixture as solutions of manganous acetate tetrahydrate [C4H6MnO44H2O] as a manganese source, thiourea [(H2 N) 2 CS] as a sulfur source and triethanolamine (TEA) [(HOC2H4)3N] as a complexing agent.In the present paper the deposition was successfully done at 60 °C temperature. The absorption properties and band gap energy were determined employing double beam spectrophotometer. The optical band gap value calculated from absorption spectra of MnS thin film is found to be about 3.1eV.The MnS thin film was structurally characterized by X-ray Diffraction (XRD). The MnS thin film was morphologically characterized by Scanning Electron Microscopy (SEM) and elemental analysis was performed using EDS to confirm the formation of MnS.

Properties of TiO2 Thin Film Prepared by Sol-Gel Dip Coating

2015 ◽  
Vol 723 ◽  
pp. 528-531
Author(s):  
Jun Wang ◽  
Ling Yun Bai
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Refractive Index ◽  
Optical Properties ◽  
Band Gap ◽  
Optical Band Gap ◽  
Sol Gel ◽  
Dip Coating ◽  
Gel Method ◽  
Glass Substrates

TiO2 thin films were prepared on glass substrates by sol-gel method. The effect of withdraw speed on the thickness and optical properties of TiO2 thin films was investigated. The films were transparent in the visible wavelength. The thickness of the TiO2 films was increased from 90 nm for the withdraw speed of 1000 μm/s to 160 nm for the withdraw speed of 2000 μm/s. While, The refractive index of the TiO2 thin film decreased from 2.38 to 2.07. It may be due to the porosity of the film was increased. The optical band-gap of the films was around 3.45 eV.

Fabrication and Photoelectrochemical Characterization of Fe, Co, Ni and Cu-Doped TiO2 Thin Films

2013 ◽  
Vol 764 ◽  
pp. 266-283 ◽  
Author(s):  
Ibram Ganesh ◽  
Rekha Dom ◽  
P.H. Borse ◽  
Ibram Annapoorna ◽  
G. Padmanabham ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Metal Ions ◽  
Band Gap ◽  
Metal Ion ◽  
Band Gap Energy ◽  
Chemical Compositions ◽  
Gap Energy ◽  
Glass Substrates ◽  
Photoelectrochemical Characterization

Different amounts of Fe, Co, Ni and Cu-doped TiO2 thin films were prepared on fluorine doped tin oxide (FTO) coated soda-lime glass substrates by following a conventional sol-gel dip-coating technique followed by heat treatment at 550 and 600°C for 30 min. These thin films were characterized for photo-current, chronoamperometry and band-gap energy values. The chemical compositions of metals-doped TiO2 thin films on FTO glass substrates were confirmed by XPS spectroscopic study. The metal-ions doped TiO2 thin films had a thickness of <200 nm="" optical="" transparency="" of="">80%, band-gap energy of >3.6 eV, and a direct band-to-band energy transition. The photoelectrochemical (PEC) studies revealed that all the metal-ions doped TiO2 thin films exhibit n-type semi-conducting behavior with a quite stable chronoamperometry and photo-currents that increase with the increase of applied voltage but decrease with the dopant metal-ion concentration in the thin film. Furthermore, these thin films exhibited flat-band potentials amenable to water oxidation reaction in a PEC cell. The 0.5 wt.% Cu-doped TiO2 thin film electrode exhibited an highest incident photon-to-current conversion efficiency (IPCE) of about 21%.

CuxSbySz THIN FILMS PRODUCED BY ANNEALING CHEMICALLY DEPOSITED Sb2S3-CuS THIN FILMS

2001 ◽  
Vol 15 (17n19) ◽  
pp. 667-670 ◽  
Author(s):  
Y. RODRÍGUEZ-LAZCANO ◽  
M. T. S. NAIR ◽  
P. K. NAIR
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Optical Band Gap ◽  
Deposition Method ◽  
Photovoltaic Devices ◽  
Large Area ◽  
Electrical And Optical Properties ◽  
Ternary Compounds ◽  
Glass Substrates ◽  
Different Temperatures

The possibility of generating ternary compounds through annealing thin film stacks of binary composition has been demonstrated before. In this work we report a method to produce large area coating of ternary compounds through a reaction in solid state between thin films of Sb2S3 and CuS. Thin films of Sb2S3 -CuS were deposited on glass substrates in the sequence of Sb2S3 followed by CuS (on Sb2S3 ) using chemical bath deposition method. The multilayer stack, thus produced, of approximately 0.5 μm in thickness, where annealed under nitrogen and argon atmospheres at different temperatures to produce films of ternary composition, CuxSbySz . An optical band gap of ~1.5 eV was observed in these films, suggesting that the thin films of ternary composition formed in this way are suitable for use as absorber materials in photovoltaic devices. The results on the analyses of structural, electrical and optical properties of films formed with different combinations of thickness in the multilayers will be discussed in the paper.

scholarly journals Effect of concentration of cadmium sulfate solution on structural, optical and electric properties of Cd1–x Zn x S thin films

2021 ◽  
Vol 42 (11) ◽  
pp. 112101
Author(s):  
Yuming Xue ◽  
Shipeng Zhang ◽  
Dianyou Song ◽  
Liming Zhang ◽  
Xinyu Wang ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Band Gap ◽  
Optical Band Gap ◽  
Film Growth ◽  
Structural Characteristics ◽  
Hexagonal Phase ◽  
Zinc Content ◽  
Sulfate Concentration ◽  
Cadmium Sulfate

Abstract Cd1– x Zn x S thin films were deposited by chemical bath deposition (CBD) on the glass substrate to study the influence of cadmium sulfate concentration on the structural characteristics of the thin film. The SEM results show that the thin film surfaces under the cadmium sulfate concentration of 0.005 M exhibit better compactness and uniformity. The distribution diagrams of thin film elements illustrate the film growth rate changes on the trend of the increase, decrease, and increase with the increase of cadmium sulfate concentration. XRD studies exhibit the crystal structure of the film is the hexagonal phase, and there are obvious diffraction peaks and better crystallinity when the concentration is 0.005 M. Spectrophotometer test results demonstrate that the relationship between zinc content x and optical band gap value E g can be expressed by the equation E g(x) = 0.59x 2 + 0.69x + 2.43. Increasing the zinc content can increase the optical band gap, and the absorbance of the thin film can be improved by decreasing the cadmium sulfate concentration, however, all of them have good transmittance. At a concentration of 0.005 M, the thin film has good absorbance in the 300–800 nm range, 80% transmittance, and band gap value of 3.24 eV, which is suitable for use as a buffer layer for solar cells.

scholarly journals The Properties of Zn-Doped AlSb Thin Films Prepared by Pulsed Laser Deposition

Coatings ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 136
Author(s):  
Ping Tang ◽  
Weimin Wang ◽  
Bing Li ◽  
Lianghuan Feng ◽  
Guanggen Zeng
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Band Gap ◽  
Photovoltaic Effect ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Sem Images ◽  
Glass Substrates ◽  
Substrate Temperatures

Aluminum antimony (AlSb) is a promising photovoltaic material with a band gap of about 1.62 eV. However, AlSb is highly deliquescent and not stable, which has brought great difficulties to the applications. Based on the above situation, there are two purposes for preparing our Zn-doped AlSb (AlSb:Zn) thin films: One is to make P-type AlSb and the other is to find a way to suppress the deliquescence of AlSb. The AlSb:Zn thin films were prepared on glass substrates at different substrate temperatures by using the pulsed laser deposition (PLD) method. The structural, surface morphological, optical, and electrical properties of AlSb:Zn films were investigated. The crystallization of AlSb:Zn thin films was enhanced and the electrical resistivity decreased as the substrate temperature increased. The scanning electron microscopy (SEM) images indicated that the grain sizes became bigger as the substrate temperatures increased. The Raman vibration mode AlSb:Zn films were located at ~107 and ~142 cm−1 and the intensity of Raman peaks was stronger at higher substrate temperatures. In the experiment, a reduced band gap (1.4 eV) of the AlSb:Zn thin film was observed compared to the undoped AlSb films, which were more suitable for thin-film solar cells. Zn doping could reduce the deliquescent speed of AlSb thin films. The fabricated heterojunction device showed the good rectification behavior, which indicated the PN junction formation. The obvious photovoltaic effect has been observed in an FTO/ZnS/AlSb:Zn/Au device.

scholarly journals Studies on the Optical Properties and Surface Morphology of Nickel Phthalocyanine Thin Films

2007 ◽  
Vol 4 (2) ◽  
pp. 255-264 ◽  
Author(s):  
Benny Joseph ◽  
C. S. Menon
Keyword(s):  
Thin Films ◽  
Surface Morphology ◽  
Band Gap ◽  
Electron Micrographs ◽  
Optical Band Gap ◽  
Scanning Electron Micrographs ◽  
Nickel Phthalocyanine ◽  
Glass Substrates ◽  
Substrate Temperatures ◽  
Scanning Electron

Thin films of Nickel Phthalocyanine (NiPc) are fabricated at a base pressure of 10-5m.bar using Hind-Hivac thermal evaporation plant. The films are deposited on to glass substrates at various temperatures 318, 363, 408 and 458K. The optical absorption spectra of these thin films are measured. Present studies reveal that the optical band gap energies of NiPc thin films are highly dependent on the substrate temperatures. The structure and surface morphology of the films deposited on glass substrates of temperatures 303, 363 and 458K are studied using X-ray diffractograms and Scanning Electron Micrographs (SEM), show that there is a change in the crystallinity and surface morphology due to change in the substrate temperatures. Full width at half maximum (FWHM) intensity of the diffraction peaks is also found reduced with increasing substrate temperatures. Scanning electron micrographs show that these crystals are fiber like at high substrate temperatures. The optical band gap increases with increase in substrate temperature and is then reduced with fiber-like grains at 408K. The band gap increases again at 458K with full of fiber like grains. Trap energy levels are also observed for these films.

Properties of CdS Thin Films Grown by Chemical Bath Deposition as a Function of Bath Temperature

2009 ◽  
Vol 609 ◽  
pp. 243-247 ◽  
Author(s):  
H. Moualkia ◽  
S. Hariech ◽  
M.S. Aida
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Band Gap ◽  
Chemical Bath Deposition ◽  
Bath Temperature ◽  
Band Gap Energy ◽  
X Ray Diffraction ◽  
Glass Substrates ◽  
Cds Thin Films ◽  
Direct Band

The present work deals with the preparation and characterization of cadmium sulfur (CdS) thin films. These films are prepared by chemical bath deposition on the well cleaned glass substrates. The thickness of the samples was measured by using profilometer DEKTAK, structural and optical properties were studied by X-ray diffraction analysis, and UV-visible spectrophotometry. The optical properties of the films have been investigated as a function of temperature. The band gap energy and Urbach energy were also investigated as a function of temperature. From the transmittance data analysis the direct band gap ranges from 2.21 eV to 2.34 eV. A dependence of band gap on temperature has been observed and the possible raisons are discussed. Transmission spectra indicates a high transmission coefficient (75 %). Structural analysis revealed that the films showed cubic structure, and the crystallite size decreased at a higher deposition temperature.

Influence of Ti-Doping on the Thermoelectric Properties of ZnO:Al Thin Films

2013 ◽  
Vol 734-737 ◽  
pp. 2391-2394
Author(s):  
Qing Yun Lin ◽  
Ping Fan ◽  
Jing Ting Luo ◽  
Zhuang Hao Zheng ◽  
Ying Zhen Li ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Thermoelectric Properties ◽  
Hexagonal Wurtzite Structure ◽  
Oxide Thin Film ◽  
Xrd Pattern ◽  
Absolute Value ◽  
Glass Substrates ◽  
Maximum Conductivity ◽  
Ti Doping

Ti doped aluminum zinc oxide thin film was prepared by DC reaction magnetron sputtering method on the transparent glass substrates. The structure and thermoelectric performance of the deposited (TAZO) thin films are studied by various methods. XRD pattern shows that the TAZO thin film exhibits hexagonal wurtzite structure. After Ti-doping, the thermoelectric properties of TAZO thin film significantly improved at room temperature. The TAZO thin film has the maximum conductivity of 8.33×104 S/m and the Seebeck coefficient absolute value of 34 μV/K, which is respectively larger than that of the corresponding values.

Sign in / Sign up

Export Citation Format

Share Document