X-ray radiometric processing technology for quartz raw material

In this study, corn cob was used as raw material and modified methods employing KOH and KMnO4 were used to prepare activated carbon with high adsorption capacity for mercury ions. Experiments on the effects of different influencing factors on the adsorption of mercury ions were undertaken. The results showed that when modified with KOH, the optimal adsorption time was 120 min, the optimum pH was 4; when modified with KMnO4, the optimal adsorption time was 60 min, the optimal pH was 3, and the optimal amount of adsorbent and the initial concentration were both 0.40 g/L and 100 mg/L under both modified conditions. The adsorption process conforms to the pseudo-second-order kinetic model and Langmuir model. Scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDS), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and Zeta potential characterization results showed that the adsorption process is mainly physical adsorption, surface complexation and ion exchange.

Download Full-text

Cotton stalk-derived hydrothermal carbon for methylene blue dye removal: investigation of the raw material plant tissues

Bioresources and Bioprocessing ◽

10.1186/s40643-021-00364-8 ◽

2021 ◽

Vol 8 (1) ◽

Author(s):

Libo Zhang ◽

Junyan Tan ◽

Gangying Xing ◽

Xintong Dou ◽

Xuqiang Guo

Keyword(s):

Methylene Blue ◽

Functional Materials ◽

Raw Material ◽

Plant Tissues ◽

Chemical Compositions ◽

Waste Biomass ◽

Cotton Stalk ◽

Acid Base ◽

X Ray ◽

Bet Analysis

AbstractConversion of the abundant agricultural residual cotton stalk (CS) into useful chemicals or functional materials could alleviate the fossil fuels caused energy shortages and environmental crises. Although some advances have been achieved, less attention has been paid to the plant tissues effect. In this study, the plant tissue of CS was changed by part degradation of some components (hemicelluloses and lignin, for example) with the aid of acid/base (or both). The pretreated CS was transformed into hydrochar by hydrothermal carbonization (HTC) method. Morphological and chemical compositions of CS hydrochar were analyzed by various techniques, including elemental analysis, Fourier transform infrared (FTIR), BET analysis, X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). Methylene blue (MB) removal of prepared CS hydrochar was used to evaluate CS hydrochar pollutions adsorption capacity. Results reveal acid/base (or both) pretreatment is beneficial for CS raw material to prepare high-quality CS hydrochar. The effects of some parameters, such as initial MB concentration, temperature, pH value and recyclability on the adsorption of MB onto both acid and base-pretreated CS hydrochar (CS-H2SO4 + NaOH-HTC) were studied. The present work exhibits the importance of agricultural waste biomass material plant tissues on its derived materials, which will have a positive effect on the direct utilization of waste biomass.

Download Full-text

Geochemistry and Mineralogy of Ice-Dammed Lake Sediments of the Lębork Deposit

Clays and Clay Minerals ◽

10.1007/s42860-021-00129-6 ◽

2021 ◽

Author(s):

Radosław Rogoziński ◽

Alina Maciejewska

Keyword(s):

Chemical Composition ◽

Lake Sediments ◽

Inductively Coupled Plasma ◽

Mineralogical Composition ◽

Raw Material ◽

Element Analysis ◽

X Ray ◽

Dominant Component ◽

Clay Deposits ◽

Dammed Lake

AbstractVarved clay deposits from ice-dammed lakes are a particularly important and broadly applied raw material used for the production of high-quality ceramics (red bricks, roof tiles, etc.), but the mineralogy and geochemistry of these sediments are not fully understood. The aim of the present study was to determine the chemical and mineralogical composition of ice-dammed lake sediments of the Lębork deposit. Major-element analysis of the compositions of selected samples from the ice-dammed lake clays was performed by X-ray fluorescence (XRF) and trace elements were determined by inductively coupled plasma-mass spectrometry. The mineralogical composition of clay samples was determined by X-ray diffraction (XRD). Analyses of the chemical composition of the ice-dammed lake clays of the Lębork deposit showed that the dominant component was SiO2 with a mean content of 56.13 wt.%; the second most abundant component was Al2O3, with a mean content for the entire deposit of 11.61 wt.%. Analysis by ICP-MS indicated the presence of rare earth elements (REE), e.g. cerium, neodymium, lanthanum, and praseodymium; their mean contents are: 56.9, 27.0, 26.3, and 7.3 ppm, respectively. Mineralogical analysis of the varved clays identified quartz, muscovite, calcite, and clay minerals – illite, kaolinite, and montmorillonite. The material filling the Lębork basin is characterized by small lateral and vertical variability in chemical composition. The results of the present study may be of considerable importance in determining the parent igneous, metamorphic, and sedimentary rocks, the weathering products of which supplied material to the ice-dammed lake, as well as in determining the mechanisms and character of the sedimentation process itself.

Download Full-text

Characterization and A Preliminary Study of TiO2 Synthesis from Lampung Iron Sand

Key Engineering Materials ◽

10.4028/www.scientific.net/kem.849.113 ◽

2020 ◽

Vol 849 ◽

pp. 113-118

Author(s):

Yayat Iman Supriyatna ◽

Slamet Sumardi ◽

Widi Astuti ◽

Athessia N. Nainggolan ◽

Ajeng W. Ismail ◽

...

Keyword(s):

Food Packaging ◽

Xrd Analysis ◽

Major Elements ◽

Raw Material ◽

Solid Residue ◽

X Ray Diffraction ◽

X Ray ◽

Leaching Solution ◽

Ti Content

The purpose of this study is to characterize Lampung iron sand and to conduct preliminary experiments on the TiO2 synthesis which can be used for the manufacturing of functional food packaging. The iron sand from South Lampung Regency, Lampung Province that will be utilized as raw material. The experiment was initiated by sieving the iron sand on 80, 100, 150, 200 and 325 mesh sieves. Analysis using X-Ray Fluorescence (XRF) to determine the element content and X-Ray Diffraction (XRD) to observe the mineralization of the iron sand was conducted. The experiment was carried out through the stages of leaching, precipitation, and calcination. Roasting was applied firstly by putting the iron sand into the muffle furnace for 5 hours at a temperature of 700°C. Followed by leaching using HCl for 48 hours and heated at 105°C with a stirring speed of 300 rpm. The leaching solution was filtered with filtrate and solid residue as products. The solid residue was then leached using 10% H2O2 solution. The leached filtrate was heated at 105°C for 40 minutes resulting TiO2 precipitates (powder). Further, the powder was calcined and characterized. Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca. The highest Ti content is found in mesh 200 with 9.6%, while iron content is about 80.7%. While from the XRD analysis, it shows five mineral types namely magnetite (Fe3O4), Rhodonite (Mn, Fe, Mg, Ca) SiO3, Quart (SiO2), Ilmenite (FeOTiO2) and Rutile (TiO2). The preliminary experiment showed that the Ti content in the synthesized TiO2 powder is 21.2%. The purity of TiO2 is low due to the presence of Fe metal which is dissolved during leaching, so that prior to precipitation purification is needed to remove impurities such as iron and other metals.

Download Full-text

Sedimentary Clays as Geopolymer Precursor

International Journal of Engineering Research in Africa ◽

10.4028/www.scientific.net/jera.39.97 ◽

2018 ◽

Vol 39 ◽

pp. 97-111

Author(s):

F. Mostefa ◽

Nasr Eddine Bouhamou ◽

H.A. Mesbah ◽

Salima Aggoun ◽

D. Mekhatria

Keyword(s):

Sodium Hydroxide ◽

Mineralogical Composition ◽

Cementitious Materials ◽

Raw Material ◽

X Ray Diffraction ◽

Calcination Time ◽

Calorimetric Analysis ◽

X Ray ◽

Before And After ◽

Mechanical Performances

This work aims to study the feasibility of making a geopolymer cement based on dredged sediments, from the Fergoug dam (Algeria) and to evaluate their construction potential particularly interesting in the field of special cementitious materials. These sediments due to their mineralogical composition as aluminosilicates; are materials that can be used after heat treatment. Sedimentary clays were characterized before and after calcination by X-ray diffraction, ATG / ATD, spectroscopy (FTIR) and XRF analysis. The calcination was carried out on the raw material sieved at 80 μm for a temperature of 750 ° C, for 3.4 and 5 hours. The reactivity of the calcined products was measured using isothermal calorimetric analysis (DSC) on pastes prepared by mixing an alkaline solution of sodium hydroxide (NaOH) 8 M in an amount allowing to have a Na / Al ratio close to 1 (1: 1). Also, cubic mortar samples were prepared with a ratio L / S: 0.8, sealed and cured for 24 hours at 60 ° C and then at room temperature until the day they were submited to mechanical testing. to check the extent of geopolymerization. The results obtained allowed to optimize the calcination time of 5 hours for a better reactivity of these sediments, and a concentration of 8M of sodium hydroxide and more suitable to have the best mechanical performances.

Download Full-text

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.620.314 ◽

2012 ◽

Vol 620 ◽

pp. 314-319

Author(s):

Nur Amira Mamat Razali ◽

Fauziah Abdul Aziz ◽

Saadah Abdul Rahman

Keyword(s):

Electron Microscopy ◽

Scanning Electron Microscopy ◽

Alkaline Treatment ◽

Raw Material ◽

X Ray Diffraction ◽

X Ray ◽

Preliminary Preparation ◽

Characterization Studies ◽

Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

Download Full-text

Study on Influence of Silicate Morphology Based on pH Value

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.454.324 ◽

2012 ◽

Vol 454 ◽

pp. 324-328

Author(s):

Yan He ◽

Ya Jing Liu ◽

Yong Lin Cao ◽

Li Xia Zhou

Keyword(s):

Silicic Acid ◽

Ph Value ◽

Colorimetric Method ◽

Absorption Spectrometry ◽

Degree Of Polymerization ◽

Raw Material ◽

X Ray Diffraction ◽

X Ray ◽

Ph Values ◽

The Stability

Infra-red absorption spectrometry, X-ray diffraction observations and characterization tests based on silicon molybdenum colorimetric method were used to investigate the optimal pH value controlling the stability of the silicic acid form. The experiment process was done by using sodium silicate as raw material. The results showed that the solution of silicate influenced the polymerization. The active silicic acid solution with a certain degree of polymerization was obtained by controlling the pH values.

Download Full-text

Effect of Nickel on Titanium Carbide Synthesized via Tungsten Inert Gas (TIG) Method

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.620.384 ◽

2012 ◽

Vol 620 ◽

pp. 384-388

Author(s):

Sharifah Aishah Syed Salim ◽

Julie Juliewatty Mohamed ◽

Zainal Arifin Ahmad ◽

Zainal Arifin Ahmad

Keyword(s):

Electron Microscope ◽

Scanning Electron Microscope ◽

Powder Mixture ◽

Raw Material ◽

Inert Gas ◽

X Ray Diffraction ◽

X Ray ◽

Arc Melting ◽

Elemental Powder Mixture ◽

Scanning Electron

Numerous methods have been used to produce high purity TiC. There is no previous study has been reported on the formation using single elemental powders of Titanium (Ti) and Carbon (C) with addition Nickel (Ni) by tungsten inert gas (TIG) weld method. In this work, TiC was synthesized via TIG method by arc melting elemental powder mixture of Ti and C at ~5 second (s) and 80 ampere (A). The effect Ni contents on TiC formation was investigated. The mixed raw material was ball milled for 24 hours followed by synthesis via TIG method. The arced samples were characterized by X-ray diffraction (XRD) and Scanning electron microscope (SEM). It was revealed, that small amount of Ni additive to the metal powder allows the production of dense and tough TiC.

Download Full-text

The Experimental of Low Temperature Color Slip for Decorative on Earthenware Body

Key Engineering Materials ◽

10.4028/www.scientific.net/kem.690.282 ◽

2016 ◽

Vol 690 ◽

pp. 282-285

Author(s):

Soravich Mulinta

Keyword(s):

Low Temperature ◽

Physical Properties ◽

Manganese Oxide ◽

Ferric Oxide ◽

Potassium Feldspar ◽

Raw Material ◽

Blue Color ◽

X Ray ◽

Yellow Color

The purpose of the study was to investigate the effects of dolomite body, frit and potassium feldspar on the properties of color slip for decorative method of color slip on earthen ware production. The characterization of raw material was analyzed by X-ray fluorescence (XRF). The experiment started with triaxial blend of dolomite body, frit and potassium feldspar in the defined ratio and then to painting of color slips on earthenware production. After that, firing specimens at 950 °C in oxidation atmosphere. Finally, the specimens were tested microstructure and physical properties. The results showed that the ratio of 50% dolomite body, 40% frit and 10% potassium feldspar were optimum properties for decorative on earthenware body. In color slip consisting of blue color added Cobalt oxide 1% ,Green colors added chromic oxide 10% , Gray color added manganese oxide 10% ,yellow color added stain 2225 10% and hazel color added ferric oxide 2 wt %.

Download Full-text

The Effect of Different Methods to Pretreat Reed Pulp on the Crystallinity of Microcrystalline Cellulose

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.1056.12 ◽

2014 ◽

Vol 1056 ◽

pp. 12-15 ◽

Cited By ~ 1

Author(s):

Wen Long Zhang ◽

Wen Long Zhao ◽

Ya Jie Dai

Keyword(s):

Crystallite Size ◽

Microcrystalline Cellulose ◽

Average Crystallite Size ◽

Comprehensive Analysis ◽

Raw Material ◽

Type I ◽

X Ray Diffraction ◽

X Ray ◽

Dimethyl Acetamide ◽

Crystal Type

Reed Pulp was Raw Material that Pretreated by Four Methods {ultrasonic, Microwave, N, N-Dimethyl Acetamide (DMAc) and Tetrahydrofuran (THF)}. Reed Microcrystalline Cellulose (MCC) was Prepared by the Dilute Hydrochloric Acid Hydrolysis from Pretreated Reed Pulp. the Influences of Pretreatment Methods on Crystalline Type, Crystallinity and Crystallite Size of MCC were Investigated by X-Ray Diffraction (XRD). the Results Showed that the Crystallinity of MCC with Four Pretreatment Methods was 68.45%, 62.28%, 63.21% and 69.56%, Respectively. the Average Crystallite Size of MCC Prepared by Hydrolysis after Pretreated by Dmac was the Largest. whereas, the Crystal Type of MCC was Not Changed, it was still the Cellulose Type I. Comprehensive Analysis Indicated that the Effects of MCC Prepared by Hydrolysis after Pretreated by Ultrasonic were the Best.

Download Full-text