Tectoniques superposes et metamorphisme dans la bande cristallophyllienne d'Aracena (province de Huelva, Espagne)

1967 ◽  
Vol S7-IX (1) ◽  
pp. 111-128 ◽  
Author(s):  
Jean Pierre Bard
Keyword(s):  
High Temperature ◽  
Structural Analysis ◽  
Low Pressure ◽  
Second Phase ◽  
The South ◽  
Metamorphic Belt ◽  
Third Phase ◽  
Granitic Intrusion ◽  
Hercynian Orogeny

Abstract Structural analysis of the Paleozoic formations of the Aracena metamorphic belt reveals the presence of four main deformational phases all of which belong to the Hercynian orogeny: a first phase of NW-SE synmetamorphic isoclinal folds overturned toward the southwest and penecontemporaneous with migmatization; a second phase of WNW-ESE orthorhombic folds with axes slightly overturned toward the south-southwest, accompanied by S <sub>2</sub> schistosity fracture and late epizonal granitic intrusion; a third phase of thrusting and shearing toward the south-southwest; a fourth phase of NE-SW displacements measurable in kilometers. Estimation of the geothermal value of the synmetamorphic phase ( nearly equal 80 degrees C/km) places the Aracena belt among the high temperature-low pressure types.

Prograde polyphase regional metamorphism of pelitic rocks, NW of Jamshedpur, eastern India: constraints from textural relationship, pseudosection modelling and geothermobarometry

2019 ◽  
Vol 157 (7) ◽  
pp. 1045-1067
Author(s):  
D Prakash ◽  
DK Patel ◽  
MK Yadav ◽  
B Vishal ◽  
S Tewari ◽  
...  
Keyword(s):  
Regional Metamorphism ◽  
Model System ◽  
Second Phase ◽  
Eastern India ◽  
Prograde Metamorphism ◽  
Metamorphic Belt ◽  
Granitic Intrusion ◽  
Two Phases ◽  
Textural Relationship ◽  
Pelitic Rocks

AbstractThe study area belongs to the Singhbhum metamorphic belt of Jharkhand, situated in the eastern part of India. The spatial distribution of the index minerals in the pelitic schists of the area shows Barrovian type of metamorphism. Three isograds, viz. garnet, staurolite and sillimanite, have been delineated and the textural study of the schists has revealed a time relation between crystallization and deformation. Series of folds with shifting values of plunges in the supracrustal rocks having axial-planar schistosity to the folds have been widely cited. Development of these folds could be attributed to the second phase of deformation. In total, two phases of deformation, D1 and D2, in association with two phases of metamorphism, M1 and M2, have been lined up in the study area. Chemographic plots of reactant and product assemblages corresponding to various metamorphic reactions suggest that the pattern of metamorphic zones mapped in space is in coherence with the temporal-sequential change during prograde metamorphism. The prograde P–T evolution of the study area has been obtained using conventional geothermobarometry, internally consistent winTWQ program and Perple_X software in the MnNCKFMASHTO model system. Our observations suggest that the progressive metamorphism in the area is not related to granitic intrusion or migmatization but that it was possibly the ascending plume that resulted in the M1 phase of metamorphism followed by D1 deformation. The second and prime metamorphic phase, M2, with its possible heat source generated by crustal overloading, was preceded by D1 and it lasted until late- to post-D2 deformation.

scholarly journals Graphite occurrences in the low-pressure/high-temperature metamorphic belt of the Sierra de Aracena (southern Iberian Massif)

2000 ◽  
Vol 64 (5) ◽  
pp. 801-814 ◽  
Author(s):  
M. Rodas ◽  
F. J. Luque ◽  
J. F. Barrenechea ◽  
J. C. Fernández-Caliani ◽  
A. Miras ◽  
...  
Keyword(s):  
High Temperature ◽  
Isotope Analysis ◽  
Granulite Facies ◽  
Low Pressure ◽  
Iberian Massif ◽  
Metamorphic Belt ◽  
Sw Spain ◽  
Mode Of Occurrence ◽  
Dta Curves ◽  
Terrigenous Sequence

AbstractFour distinct associations of graphite have been identified in the low-pressure, high-temperature belt of the Sierra de Aracena (SW Spain). Syngenetic occurrences include: (1) stratiform graphite mineralization within a calc-silicate series; (2) disseminated graphite within a terrigenous sequence; and (3) ‘restitic’ graphite within anatectic tonalites and their enclaves. Epigenetic graphite occurs as (4) veins cross-cutting mafic granulites.Graphite in all types of occurrences is highly crystalline, with the c parameter close to 6.70 Å. Such c values correspond to temperatures of formation of ∼800°C. The thermal properties of graphite are also typical of well-ordered graphite and provide DTA exothermic maxima ranging from 810 to 858°C depending on the mode of occurrence. The differences among the temperatures of formation estimated by graphite geothermometry, the position of the exothermic maximum in the DTA curves, and petrologic geothermometers are discussed in terms of the applicability of graphite geothermometry to granulite-facies rocks. Carbon isotope analysis yields δ13C values in the range from −31.6 to −21.4% for syngenetic graphite of types I, II and III attributable to biogenically-derived carbon. The heavier signatures for graphite in vein occurrences (δ13C= −17.7 to −18.3%) with respect to syngenetic graphites suggest that isotopically heavy carbonic species were incorporated into the metamorphic fluids (probably as a consequence of decarbonation reactions of the calc-silicate rocks) from which graphite precipitated into the veins. These fluids were strongly channelled through structural pathways.

TEM Studies of Grain Boundary Films in Si3N4 Ceramics

1991 ◽  
Vol 49 ◽  
pp. 930-931
Author(s):  
H.-J. Kleebe ◽  
J.S. Vetrano ◽  
J. Bruley ◽  
M. Rühle
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Silicon Nitride ◽  
Hot Isostatic Pressing ◽  
Amorphous Film ◽  
Liquid Phase Sintering ◽  
Second Phase ◽  
High Temperature Mechanical Properties ◽  
Triple Points ◽  
Boundary Films

It is expected that silicon nitride based ceramics will be used as high-temperature structural components. Though much progress has been made in both processing techniques and microstructural control, the mechanical properties required have not yet been achieved. It is thought that the high-temperature mechanical properties of Si3N4 are limited largely by the secondary glassy phases present at triple points. These are due to various oxide additives used to promote liquid-phase sintering. Therefore, many attempts have been performed to crystallize these second phase glassy pockets in order to improve high temperature properties. In addition to the glassy or crystallized second phases at triple points a thin amorphous film exists at two-grain junctions. This thin film is found even in silicon nitride formed by hot isostatic pressing (HIPing) without additives. It has been proposed by Clarke that an amorphous film can exist at two-grain junctions with an equilibrium thickness.

Microstructural characterization of a rapidly solidified Al-Fe-V-Si alloy for elevated temperature applications

1988 ◽  
Vol 46 ◽  
pp. 550-551
Author(s):  
R. E. Franck ◽  
J. A. Hawk ◽  
G. J. Shiflet
Keyword(s):  
High Temperature ◽  
Elevated Temperature ◽  
Grain Growth ◽  
Volume Fraction ◽  
Microstructural Characterization ◽  
Second Phase ◽  
Microstructural Stability ◽  
Elevated Temperature Strength ◽  
Temperature Applications

Rapid solidification processing (RSP) is one method of producing high strength aluminum alloys for elevated temperature applications. Allied-Signal, Inc. has produced an Al-12.4 Fe-1.2 V-2.3 Si (composition in wt pct) alloy which possesses good microstructural stability up to 425°C. This alloy contains a high volume fraction (37 v/o) of fine nearly spherical, α-Al12(Fe, V)3Si dispersoids. The improved elevated temperature strength and stability of this alloy is due to the slower dispersoid coarsening rate of the silicide particles. Additionally, the high v/o of second phase particles should inhibit recrystallization and grain growth, and thus reduce any loss in strength due to long term, high temperature annealing.The focus of this research is to investigate microstructural changes induced by long term, high temperature static annealing heat-treatments. Annealing treatments for up to 1000 hours were carried out on this alloy at 500°C, 550°C and 600°C. Particle coarsening and/or recrystallization and grain growth would be accelerated in these temperature regimes.

Precipitation of NiHfsi phase in NiAl single crystals containing Hf

1995 ◽  
Vol 53 ◽  
pp. 532-533
Author(s):  
A. Garg ◽  
R. D. Noebe ◽  
R. Darolia
Keyword(s):  
High Temperature ◽  
Single Crystals ◽  
High Temperature Strength ◽  
Bridgman Technique ◽  
Shell Mold ◽  
Third Phase ◽  
Unknown Phase ◽  
Transmission Electron ◽  
Two Phases ◽  
Nial Matrix

Small additions of Hf to NiAl produce a significant increase in the high-temperature strength of single crystals. Hf has a very limited solubility in NiAl and in the presence of Si, results in a high density of G-phase (Ni16Hf6Si7) cuboidal precipitates and some G-platelets in a NiAl matrix. These precipitates have a F.C.C structure and nucleate on {100}NiAl planes with almost perfect coherency and a cube-on-cube orientation-relationship (O.R.). However, G-phase is metastable and after prolonged aging at high temperature dissolves at the expense of a more stable Heusler (β'-Ni2AlHf) phase. In addition to these two phases, a third phase was shown to be present in a NiAl-0.3at. % Hf alloy, but was not previously identified (Fig. 4 of ref. 2 ). In this work, we report the morphology, crystal-structure, O.R., and stability of this unknown phase, which were determined using conventional and analytical transmission electron microscopy (TEM).Single crystals of NiAl containing 0.5at. % Hf were grown by a Bridgman technique. Chemical analysis indicated that these crystals also contained Si, which was not an intentional alloying addition but was picked up from the shell mold during directional solidification.

Precipitate coarsening during hot-compression testing of NiAl + 2 at.% Nb

1986 ◽  
Vol 44 ◽  
pp. 598-599
Author(s):  
W. M. Sherman ◽  
K. M. Vedula
Keyword(s):  
High Temperature ◽  
Flow Stress ◽  
Weight Ratio ◽  
Constant Strain Rate ◽  
Hot Compression ◽  
Compression Testing ◽  
Second Phase ◽  
Precipitate Coarsening ◽  
High Temperature Mechanical Properties ◽  
Ordered Intermetallic

The strength to weight ratio and oxidation resistance of NiAl make this ordered intermetallic, with some modifications, an attractive candidate to compete with many superalloys for high temperature applications. Recent studies have shown that the inherent brittleness of many polycrystalline intermetallics can be overcome by micro and macroalloying. It has also been found that the high temperature mechanical properties of NiAl can be enhanced through the addition of Nb by powder metallurgical techniques forming a dispersed second phase through interdiffusion in a polycrystalline matrix. A drop in the flow stress is observed however in a NiAl-2 at.% Nb alloy after 0.2 % strain during constant strain rate hot compression testing at 1025°C. The object of this investigation was to identify the second phase and to determine the cause of the flow stress drop.

PENERAPAN MODEL QUANTUM LEARNING UNTUK MENINGKATKAN HASIL BELAJAR AUTOCAD SISWA KELAS X TEKNIK PEMESINAN SMK NEGERI 1 STABAT

2013 ◽  
Vol 5 (1) ◽  
Author(s):  
Abdul Hasan Saragih
Keyword(s):  
Positive Response ◽  
Phase 1 ◽  
First Grade ◽  
Learning Model ◽  
Second Phase ◽  
Phase 2 ◽  
Phase 3 ◽  
The Third ◽  
Third Phase ◽  
Quantum Learning

This classroom research was conducted on the autocad instructions to the first grade of mechinary class of SMK Negeri 1 Stabat aiming at : (1) improving the student’ archievementon autocad instructional to the student of mechinary architecture class of SMK Negeri 1 Stabat, (2) applying Quantum Learning Model to the students of mechinary class of SMK Negeri 1 Stabat, arising the positive response to autocad subject by applying Quantum Learning Model of the students of mechinary class of SMK Negeri 1 Stabat. The result shows that (1) by applying quantum learning model, the students’ achievement improves significantly. The improvement ofthe achievement of the 34 students is very satisfactory; on the first phase, 27 students passed (70.59%), 10 students failed (29.41%). On the second phase 27 students (79.41%) passed and 7 students (20.59%) failed. On the third phase 30 students (88.24%) passed and 4 students (11.76%) failed. The application of quantum learning model in SMK Negeri 1 Stabat proved satisfying. This was visible from the activeness of the students from phase 1 to 3. The activeness average of the students was 74.31% on phase 1,81.35% on phase 2, and 83.63% on phase 3. (3) The application of the quantum learning model on teaching autocad was very positively welcome by the students of mechinary class of SMK Negeri 1 Stabat. On phase 1 the improvement was 81.53% . It improved to 86.15% on phase 3. Therefore, The improvement ofstudent’ response can be categorized good.

3D Structural Analysis of Selected High-Temperature Materials

2018 ◽  
Vol 55 (7) ◽  
pp. 424-446
Author(s):  
U. Jäntsch ◽  
M. Klimenkov ◽  
A. Möslang ◽  
F. Reinauer ◽  
J. Reiser ◽  
...  
Keyword(s):  
High Temperature ◽  
Structural Analysis ◽  
High Temperature Materials

Mixed-Methods Evaluation as Scaffold to the Development of a Mobile Health Application to Support the Prescription of Wheelchairs and Postural Support Devices (Preprint)

2020 ◽  
Author(s):  
Adriana Klein ◽  
Roseli de Deus Lopes ◽  
Rodrigo Suigh
Keyword(s):  
Mixed Methods ◽  
Mobile Health ◽  
Second Phase ◽  
The Third ◽  
Evaluation Approach ◽  
Mixed Methods Evaluation ◽  
Usability Tests ◽  
Third Phase ◽  
Postural Support ◽  
Support Devices

BACKGROUND EasySeating is a mobile health (mHealth) app that supports the prescription of wheelchair and postural support devices (WPSD). It can be used by occupational therapists (OT) and physiotherapists (PT) who prescribe WPSD. The app offers a standardization of the prescription procedure, showing images, metrics and details that guide the prescriber to decide on the best equipment. It was developed with an iterative mixed-methods evaluation approach. Objective: The aim of this study was to investigate the processes involved in the prescription of WPSD and to propose, develop and evaluate a mHealth to support OT and PT prescribers. OBJECTIVE The aim of this study was to investigate the processes involved in the prescription of WPSD and to propose, develop and evaluate a mHealth to support OT and PT prescribers. METHODS This study was divided into three phases and was carried out as an iterative process composed of user consulting/testing (using a mixed-methods evaluation approach), system (re)design and software development. The first phase consisted of the collection of qualitative and quantitative data to map and understand the users requirements and of the development of the first prototype (v1) of the app. This data collection was performed through semi-structured interviews with 14 OT and PT prescribers, 5 specialized technicians and 5 WPSD users. The second phase aimed at improving the overall functionality of the app and consisted in the development, test and evaluation of the prototypes v1, v2, v3 and v4. A total of 59 prescribers tested and evaluated these prototypes by means of open interviews, semi-structured questionnaires and focus groups. The third phase focused in the usability aspects of the app. It consisted in the development and test of the prototype v5. Eight technology specialists assessed its usability through heuristics evaluation. RESULTS Data collected in phase one indicated there is a lack of standardization on the prescription of postural support devices (PSD). A divergent nomenclature for the PSDs was also found and classified in eight categories. These information guided the development of the first prototype of the EasySeating app. Phase two results pointed that the prescribers value the insertion of the app into their clinical practice, as it accelerates and increases the quality of the evaluation process and improves the organization of the prescription information. Significant suggestions for the improvement of the app were given during the users tests, including the use of images to represent the PSDs. The usability tests from the third phase revealed two strong issues that must be solved: the need of greater feedback and failures in the persistence of the input data. CONCLUSIONS This study demonstrated that there is a lack of systematization of the WPSD prescription process. The evaluation of the developed EasySeating app demonstrated that there is a potential to standardize, integrate and organize the WPSD prescription information, supporting and facilitating the decision making process of the prescribers. CLINICALTRIAL This study was approved by the Research Ethics Board of the Universidade de São Paulo (registered protocol n°53929516.6.0000.0065) URL - http://plataformabrasil.saude.gov.br/login.jsf

Sign in / Sign up

Export Citation Format

Share Document