Condensate Banking Removal Using Slow Release of In-Situ Energized Fluid

2021 ◽  
Author(s):  
Ayman Al-Nakhli ◽  
Amjed Hassan ◽  
Mohamed Mahmoud ◽  
Abdualilah Al-Baiz ◽  
Wajdi Buhaezah
Keyword(s):  
Slow Release ◽  
Computer Modelling ◽  
Gas Injection ◽  
Thermochemical Treatment ◽  
Gas Production ◽  
Dew Point ◽  
Tight Reservoir ◽  
Novel Method ◽  
Production Period

Abstract Condensate banking represent a persistent challenge during gas production from tight reservoir. The accumulation of condensate around the wellbore can rapidly diminish gas production. When reservoir pressure drop below dew point, condensate start to dropout from gas phase, filling pores and permeable fractures, and block gas production. There are several strategies to mitigate condensate banking, however, these strategies are either demonstrate limited results or are economically not viable. In this study, a novel method to mitigate condensate was developed using thermochemical reactants. Slow-release of thermochemical reactants inside different core samples was studied. The effect of in-situ generation of gas on the petrophysical properties of the rock was reported. Thermochemical treatment was applied to recover condensate on sandstone and carbonate, where the reported recoveries were around 70%. However, when shale sample was used, the recovery was only 43%. Advanced Equation-of-State (EoS) compositional and unconventional simulator (GEM) from CMG (Computer Modelling Group) software was used to simulate thermochemical treatment and gas injection. The simulation study showed that thermochemical stimulation had increased production period from 3.5 to 22.7 months, compared to gas injection.

scholarly journals Novel Method for the production of Water from Humid Environment of Qatar

2020 ◽  
Author(s):  
Hammad Siddiqui ◽  
Osama Fayyaz ◽  
Syed Zaidi
Keyword(s):  
Water Scarcity ◽  
Middle Eastern ◽  
Climatic Conditions ◽  
Gas Production ◽  
Water Desalination ◽  
Dew Point ◽  
Peltier Effect ◽  
Atmospheric Water ◽  
Novel Method ◽  
Cooling Effects

Water scarcity is the major challenge of the upcoming decades for the entire world. Middle eastern nations are prone to water scarcity due to very less rainfall, scarce fresh water sources, sandy surroundings and harsh humid climatic conditions. Qatar being the leader of natural gas production suffers from the same problem of pure and clean water. Water desalination techniques adopted so far are energy intensive and unknown to oceanic habitat. The use of vapor compression cycle for the condensation of atmospheric water vapor has various limitations such as complex machinery, high power consumption and periodical maintenance. This novel method utilizes heavy humid conditions of Qatar to obtain water from the atmosphere through Peltier Effect. This method uses the dissimilarity of the conductors in the electric circuit such that the current is made to flow through the circuit and the heating and cooling effects are generated at the junctions where cooling temperature of the junction can be achieved below the dew point temperature thus forming the dew which is collected in the closed container as condensed atmospheric water. This technique is superior to other conventional methods of water production due to its cost efficiency, energy saving, simple machinery and portability of the entire system.

Enhancing Hydrocarbon Production Through Thermal Gas Injection from a Retrograde as Condensate Reservoir in the Western Desert in Egypt

2021 ◽  
Author(s):  
Maged Alaa Taha ◽  
Eissa Shokier ◽  
Attia Attia ◽  
Aamer Yahia ◽  
Khaled Mansour
Keyword(s):  
Carbon Dioxide ◽  
Natural Gas ◽  
Gas Injection ◽  
Gas Production ◽  
Gas Condensate ◽  
Dew Point ◽  
Western Desert ◽  
Co2 Injection ◽  
Hydrocarbon Production ◽  
Gas Condensate Reservoirs

Abstract In retrograde gas condensate reservoirs, condensate blockage is a major reservoir damage problem, where liquid is dropped-out of natural gas, below dew-point pressure. Despite that most of this liquid will not produce due to not reaching the critical saturation, natural gas will be blocked by the accumulated liquid and will also not produce. This work investigates the effects of gas injection (such as methane, carbon-dioxide, and nitrogen) and steam at high temperatures on one of the Egyptian retrograde gas condensate reservoirs. Several gas injection scenarios that comprise different combination of gas injection temperature, enthalpy, injection gas types (CO2, N2, and CH4), and injection-rates were carried out. The results indicated that all conventional and thermal gas injection scenarios do not increase the cumulative gas production more than the depletion case. The non-thermal gas injection scenarios increased the cumulative condensate production by 8.6%. However, thermal CO2 injection increased the condensate production cumulative by 28.9%. It was observed that thermal gas injection does not vaporize condensate It was observed that thermal gas injection does not vaporize condensate more than conventional injection that have the same reservoir pressure trend. However, thermal injection mainly improves the condensate mobility. Appropriately, thermal injection in retrograde reservoirs, is mostly applicable for depleted reservoirs when the largest amount of non-producible liquid is already dropped out. Finally, this research studied executing thermal gas injection in retrograde gas condensate reservoirs, operationally, by considering the following items: carbon dioxide recovery unit, compressors, storage-tanks, anti-corrosion pipe-lines and tubing-strings, and corrosion-inhibitors along with downhole gas heaters.

scholarly journals Condensate-Banking Removal and Gas-Production Enhancement Using Thermochemical Injection: A Field-Scale Simulation

Processes ◽  
2020 ◽  
Vol 8 (6) ◽  
pp. 727 ◽  
Author(s):  
Amjed Hassan ◽  
Mohamed Abdalla ◽  
Mohamed Mahmoud ◽  
Guenther Glatz ◽  
Abdulaziz Al-Majed ◽  
...  
Keyword(s):  
Gas Injection ◽  
Thermochemical Treatment ◽  
Fold Increase ◽  
Gas Production ◽  
Base Case ◽  
Field Scale ◽  
Gas Reservoirs ◽  
Gas Recovery ◽  
Compositional Simulator ◽  
The Impact

Condensate-liquid accumulation in the vicinity of a well is known to curtail gas production up to 80%. Numerous approaches are employed to mitigate condensate banking and improve gas productivity. In this work, a field-scale simulation is presented for condensate damage removal in tight reservoirs using a thermochemical treatment strategy where heat and pressure are generated in situ. The impact of thermochemical injection on the gas recovery is also elucidated. A compositional simulator was utilized to assess the effectiveness of the suggested treatment on reducing the condensate damage and, thereby, improve the gas recovery. Compared to the base case, represented by an industry-standard gas injection strategy, simulation studies suggest a significantly improved hydrocarbon recovery performance upon thermochemical treatment of the near-wellbore zone. For the scenarios investigated, the application of thermochemicals allowed for an extension of the production plateau from 104 days, as determined for the reference gas injection case, to 683 days. This represents a 6.5-fold increase in production plateau time, boosting gas recovery from 25 to 89%. The improved recovery is attributed to the reduction of both capillary pressure and condensate viscosity. The presented work is crucial for designing and implementing thermochemical treatments in tight-gas reservoirs.

scholarly journals Evaluation of the Nutrient Composition, In Vitro Fermentation Characteristics, and In Situ Degradability of Amaranthus caudatus, Amaranthus cruentus, and Amaranthus hypochondriacus in Cattle

Animals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 18
Author(s):  
Kim Margarette C. Nogoy ◽  
Jia Yu ◽  
Young Gyu Song ◽  
Shida Li ◽  
Jong-Wook Chung ◽  
...  
Keyword(s):  
Crude Protein ◽  
Dry Matter ◽  
Gas Production ◽  
Nutrient Composition ◽  
Neutral Detergent Fiber ◽  
Amaranthus Cruentus ◽  
Amaranthus Caudatus ◽  
Amaranthus Hypochondriacus

The amaranth plants showed high potential feed value as forage for ruminants. An in-depth study of this plant, particularly in cattle, will help extend its utilization as an alternative protein and fiber feed source in cattle feeding. In this study, the nutrient compositions of three different species of amaranth, Amaranthus caudatus L., Amaranthus cruentus L., and Amaranthus hypochondriacus L.—two varieties for each species, A.ca 74, A.ca 91, A.cu 62, A.cu 66, A. hy 30, and A. hy 48—were evaluated. The in vitro technique was used to evaluate the fermentation characteristics such as total gas production, total volatile fatty acids (VFA) concentration, pH, and ammonia concentration of the rumen fluid. Moreover, the effective degradabilities of dry matter (EDDM) and crude protein (EDCP) of the amaranth forages were determined through in situ bag technique. The amaranth forages: A. caudatus, A. cruentus, and A. hypochondriacus showed better nutritive value than the locally produced forages in Chungcheong province of Korea. The CP of the amaranth ranged from 11.95% to 14.19%, and the neutral detergent fiber (NDF) and acid detergent fiber (ADF) contents ranged from 45.53% to 70.88% and 34.17% to 49.83%, respectively. Among the amaranth varieties, A. hypochondriacus 48 showed the most excellent ruminant feed nutrient quality (CP, 14.19%; NDF, 45.53%; and ADF, 34.17%). The effective degradabilities of dry matter (EDDM; 33–56%) and crude protein EDCP (27–59%) of the amaranth were lower compared to other studies, which could be due to the maturity stage at which the forages were harvested. Nonetheless, A. hypochondriacus 48 showed the highest EDDM (56.73%) and EDCP (59.09%). The different amaranth species did not differ greatly in terms of total VFA concentration or molar proportions, total gas production, or ammonia-N concentration. The high nutrient composition, and highly effective degradability of dry matter and crude protein, coupled with the favorable fermentation characteristics, suggest that the amaranth forages showed good to excellent feed quality for cattle.

scholarly journals Development of a novel method for the in-situ dechlorination of immovable iron elements: optimization of Cl− extraction yield through experimental design

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Marco Veneranda ◽  
Nagore Prieto-Taboada ◽  
Jose Antonio Carrero ◽  
Ilaria Costantini ◽  
Aitor Larrañaga ◽  
...  
Keyword(s):  
Experimental Design ◽  
Optimization Design ◽  
Degradation Process ◽  
Extraction Yield ◽  
Alkaline Solutions ◽  
Iron Core ◽  
Total Consumption ◽  
Iron Leaching ◽  
Novel Method

AbstractThe conservation of iron objects exposed to marine aerosol is threatened by the formation of akaganeite, a highly unstable Cl-bearing corrosion phase. As akaganeite formation is responsible of the exfoliation of the rust layer, chlorides trigger a cyclic alteration phenomenon that often ends with the total consumption of the iron core. To prevent this degradation process, movable iron elements (e.g. archaeometallurgical artefacts) are generally immersed in alkaline dechlorination baths. Aiming to transfer this successful method to the treatment of immovable iron objects, we propose the in-situ application of alkaline solutions through the use of highly absorbent wraps. As first step of this novel research line, the present work defines the best desalination solution to be used and optimizes its extraction yield. After literature review, a screening experimental design was performed to understand the single and synergic effects of common additives used for NaOH baths. Once the most effective variables were selected, an optimization design was carried out to determine the optimal conditions to be set during treatment. According to the experimental work here presented, the use of 0.7 M NaOH solutions applied at high temperatures (above 50 °C) is recommended. Indeed, these conditions enhance chloride extraction and iron leaching inhibition, while promoting corrosion stabilization.

scholarly journals Using Sentinel-2 Images to Estimate Topography, Tidal-Stage Lags and Exposure Periods over Large Intertidal Areas

2021 ◽  
Vol 13 (2) ◽  
pp. 320
Author(s):  
José P. Granadeiro ◽  
João Belo ◽  
Mohamed Henriques ◽  
João Catalão ◽  
Teresa Catry
Keyword(s):  
Large Scale ◽  
Exposure Period ◽  
Intertidal Area ◽  
Digital Elevation ◽  
Geographical Bias ◽  
Novel Method ◽  
Tidal Stage ◽  
Sentinel 2

Intertidal areas provide key ecosystem services but are declining worldwide. Digital elevation models (DEMs) are important tools to monitor the evolution of such areas. In this study, we aim at (i) estimating the intertidal topography based on an established pixel-wise algorithm, from Sentinel-2 MultiSpectral Instrument scenes, (ii) implementing a set of procedures to improve the quality of such estimation, and (iii) estimating the exposure period of the intertidal area of the Bijagós Archipelago, Guinea-Bissau. We first propose a four-parameter logistic regression to estimate intertidal topography. Afterwards, we develop a novel method to estimate tide-stage lags in the area covered by a Sentinel-2 scene to correct for geographical bias in topographic estimation resulting from differences in water height within each image. Our method searches for the minimum differences in height estimates obtained from rising and ebbing tides separately, enabling the estimation of cotidal lines. Tidal-stage differences estimated closely matched those published by official authorities. We re-estimated pixel heights from which we produced a model of intertidal exposure period. We obtained a high correlation between predicted and in-situ measurements of exposure period. We highlight the importance of remote sensing to deliver large-scale intertidal DEM and tide-stage data, with relevance for coastal safety, ecology and biodiversity conservation.

A novel method for in situ stabilization of calcium arsenic residues via yukonite formation

2022 ◽  
pp. 153090
Author(s):  
Yumeng Wang ◽  
Shaofeng Wang ◽  
Yu Song ◽  
Peiwen Zhang ◽  
Xu Ma ◽  
...  
Keyword(s):  
In Situ Stabilization ◽  
Novel Method

Application and Exploration of Early In-Situ Combustion Huff-and-Puff Technology in a Deep Undisturbed Reservoir with Extra Heavy Oil

2021 ◽  
pp. 1-13
Author(s):  
Wang Xiaoyan ◽  
Zhao Jian ◽  
Yin Qingguo ◽  
Cao Bao ◽  
Zhang Yang ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Heavy Oil ◽  
Gas Injection ◽  
Thermal Recovery ◽  
Oil Field ◽  
Pilot Test ◽  
In Situ Combustion ◽  
Coiled Tubing

Summary Achieving effective results using conventional thermal recovery technology is challenging in the deep undisturbed reservoir with extra-heavy oil in the LKQ oil field. Therefore, in this study, a novel approach based on in-situ combustion huff-and-puff technology is proposed. Through physical and numerical simulations of the reservoir, the oil recovery mechanism and key injection and production parameters of early-stage ultraheavy oil were investigated, and a series of key engineering supporting technologies were developed that were confirmed to be feasible via a pilot test. The results revealed that the ultraheavy oil in the LKQ oil field could achieve oxidation combustion under a high ignition temperature of greater than 450°C, where in-situ cracking and upgrading could occur, leading to greatly decreased viscosity of ultraheavy oil and significantly improved mobility. Moreover, it could achieve higher extra-heavy-oil production combined with the energy supplement of flue gas injection. The reasonable cycles of in-situ combustion huff and puff were five cycles, with the first cycle of gas injection of 300 000 m3 and the gas injection volume per cycle increasing in turn. It was predicted that the incremental oil production of a single well would be 500 t in one cycle. In addition, the supporting technologies were developed, such as a coiled-tubing electric ignition system, an integrated temperature and pressure monitoring system in coiled tubing, anticorrosion cementing and completion technology with high-temperature and high-pressure thermal recovery, and anticorrosion injection-production integrated lifting technology. The proposed method was applied to a pilot test in the YS3 well in the LKQ oil field. The high-pressure ignition was achieved in the 2200-m-deep well using the coiled-tubing electric igniter. The maximum temperature tolerance of the integrated monitoring system in coiled tubing reached up to 1200°C, which provided the functions of distributed temperature and multipoint pressure measurement in the entire wellbore. The combination of 13Cr-P110 casing and titanium alloy tubing effectively reduced the high-temperature and high-pressure oxygen corrosion of the wellbore. The successful field test of the comprehensive supporting engineering technologies presents a new approach for effective production in deep extra-heavy-oil reservoirs.

Relationship between the gas production profiles of mixtures of hay and maize and the patterns of rumen fermentation observed in sheep fed those mixtures

1998 ◽  
Vol 1998 ◽  
pp. 63-63
Author(s):  
C. Rymer ◽  
D.I. Givens
Keyword(s):  
Growth Rate ◽  
Feed Intake ◽  
Rumen Fermentation ◽  
Gas Production ◽  
Post Feeding ◽  
Molar Proportion ◽  
Rumen Ph ◽  
The Mean

The gas production (GP) technique has been developed to assess dynamics of ruminant digestion. Relationships have been observed between a feed's GP profile and in vivo parameters such as digestibility (Khazaal et al., 1993), feed intake and growth rate (Blümmel and Ørskov, 1993), and in situ degradability (Sileshi et al., 1997). However, there are few studies which relate GP data to the in vivo pattern of rumen fermentation (in terms of the rate of pH decline 2 h post-feeding and the mean rumen pH, concentration of total VFA and molar proportion of individual VFA). The object of this experiment was to determine whether such a relationship existed between a feed's GP profile and the pattern of rumen fermentation observed in animals fed that feed.

Sign in / Sign up

Export Citation Format

Share Document