scholarly journals Effect of soft drink towards heat cured acrylic resin denture base surface roughness

2017 ◽  
Vol 29 (1) ◽  
Author(s):  
Pocut Aya Sofya ◽  
Liana Rahmayani ◽  
Rico Riski Candra Purnama
Keyword(s):  
Surface Roughness ◽  
Soft Drink ◽  
Acrylic Resin ◽  
Soft Drinks ◽  
Control Group ◽  
Initial Surface ◽  
Base Surface ◽  
Denture Base ◽  
Significant Difference ◽  
Paired T Test

Introduction: The absorption of fluid in the heat cured acrylic resin is able to cause the increase in surface roughness. Absorption of acidic fluid such as soft drinks can cause even higher increase of surface roughness. The objective of this study was to determined the effect of soft drinks towards heat cured acrylic resin denture base surface roughness. Methods: Specimens of this study were 32 pieces of specimen with the size of 12×12×3 mm. Sixteen pieces of specimens were kept in aquadest as a control group and 16 pieces of specimens were immersed in the soft drinks as the treatment group. Initial surface roughness was measured using surface roughness tester. The specimens were then immersed in both immersion media for 2 days. After immersion, the surface roughness of specimens were measured again. Results: Data obtained on the roughness measurements were analyzed using paired t test with the results of the analysis showed a significant difference (p<0.05). Conclusion: It was concluded that there was increased in heat cured acrylic resin denture base surface roughness after immersed in soft drinks solvent.

IMMERSION OF HEAT POLYMERIZED ACRYLIC RESIN DENTAL BASE IN ARAK BALI AGAINST SURFACE ROUGHNESS

2021 ◽  
Vol 17 (1) ◽  
pp. 22-26
Author(s):  
Kadek Ayu Wirayuni ◽  
◽  
I Made Hendri Dwi Saputra ◽  
Keyword(s):  
Surface Roughness ◽  
Acrylic Resin ◽  
Control Group ◽  
Surface Strength ◽  
Denture Base ◽  
A Value ◽  
Removable Denture ◽  
Significant Difference ◽  
Post Test ◽  
Oral Tissue

Introduction: The denture base is the part of the removable denture that is supported by good adaptation to the underlying oral tissue. Most of the denture bases are made of acrylic or polymethyl methacrylate resin, better known as PMMA. However, the acrylic resin also has disadvantages such as easily broken and absorbs liquids both water and chemicals. The chemical absorption like alcohol, ethanol, and some drinks that contain acidic materials will chemically be induced with acrylic resin and settle in the pores of the acrylic resin. The chemical damage or defect creates roughness on the surface of the acrylic resin which can cause cracking or crazing and a decrease in surface strength and hardness. Materials and Methods: The method used in this research was a laboratory experimental design with a post-test-only control group using 12 samples consisting of 2 different types of samples by measuring the surface roughness of the acrylic resin after immersing the sample with a predetermined time. Results and Discussions: One-way ANOVA test results showed a significant difference in surface roughness after the samples immersion with a value of p = 0.006 (p <0.05). Conclusions: Based on this research, can be concluded that there is an increase in the surface roughness of the heated polymerized acrylic resin for 3 hours and 4 hours of immersion. The longer the heated polymerized acrylic resin is soaked in arak hence the level of surface roughness increases.

scholarly journals The Effect of Alcoholic Beverages on Surface Roughness of Acrylic Denture Base Material

2020 ◽  
Vol 5 (1) ◽  
pp. 36-43
Author(s):  
Gladis Aprilla Rizki ◽  
Sri Wahyuningsih Rais ◽  
Martha Mozartha
Keyword(s):  
Surface Roughness ◽  
Artificial Saliva ◽  
Alcoholic Beverage ◽  
Base Material ◽  
Acrylic Resin ◽  
Alcoholic Beverages ◽  
Control Group ◽  
Test Surface ◽  
Denture Base ◽  
Significant Difference

Alcoholic beverages can be consumed in any group age, and it may be consumed by an individual using denture. Fluid absorption by heat-cured acrylic resin as a material of a denture base was able to cause an increase in its surface roughness. Absorption of an organic solvent such as the ethanol in an alcoholic beverage(s) could even increase the effect. This study aimed to evaluate the effect of alcohol beverages on surface roughness of heat-cured acrylic resin denture base. Samples (n=24) were prepared from heat-cured acrylic resin (25x25x5 mm). They were divided into 4 groups and the pre-test surface roughness was measured. Samples of each group were immersed for 10 minutes into the solution (distilled water as the control group, beer, wine, and whiskey as the test groups). After stored in artificial saliva for 23 hours, the samples were immersed into the solution, completing a period of 24 hours. This procedure was performed for 7 consecutive days and the post-test surface roughness was measured. Data were statistically analyzed using the Kruskal-Walis test. There was a significant difference in surface roughness measurement before and after the immersion (p<0.05). Whiskey was most affecting the surface roughness of heat-cured acrylic resin denture base. Alcoholic beverages could increase the surface roughness of heat cure acrylic resin denture base. Keywords: Alcoholic beverages; Heat-cured acrylic denture base; Surface roughness

Evaluation of Tissue Reaction to Some Denture-base Materials: An Animal Study

2008 ◽  
Vol 9 (4) ◽  
pp. 67-74 ◽  
Author(s):  
Behnaz Ebadian ◽  
Mohammad Razavi ◽  
Solmaz Soleimanpour ◽  
Ramin Mosharraf
Keyword(s):  
Animal Study ◽  
Weight Ratio ◽  
Acrylic Resin ◽  
Tissue Reaction ◽  
Control Group ◽  
Denture Base ◽  
Base Materials ◽  
Heat Cure ◽  
Two Samples ◽  
Significant Difference

Abstract Aim Controversy continues regarding the biocompatibility of denture base materials. One method to evaluate the biocompatibility of materials is in an animal study. Using dogs as subjects, the purpose of this study was to evaluate the vestibular tissue reaction to cobalt chromium (Co-Cr), heat cure acrylic resin, and acrylic resin mixed with aluminum oxide (Al2O3) compared with a control group using the histopathologic method. Methods and Materials Twelve disk shape samples (2 mm × 8 mm) in four groups of Co-Cr, acrylic resin, acrylic resin mixed with a 20% weight ratio of Al2O3, and a control group (Teflon) were fabricated. In one stage surgery two samples of each material (8 samples) was implanted in the buccal vestibule of each dog (n=6), subcutaneously. At 45 and 90-day intervals, half of the samples were excised along with peripheral tissue to assess the presence of inflammation by grading on a scale from 0 to 3 and the presence of a fibrotic capsule using histological observations. Data were analyzed using the Kruskal-Wallis, Mann-Whitney, and Tau b Kendal tests. Results Tissue reaction between Co-Cr and the control group was significant (P=0.02), but it was not significant between other groups. There was no significant difference between the 45 and 90-day postinsertion samples. The formation of fibrotic capsule groups was significant (P=0.01). It was significant between the Co-Cr and acrylic resin groups (P=0.01) and the acrylic resin and control groups (P=0.01). Conclusion The Co-Cr group was more toxic than the other groups. The inflammation increased during time. The inflammation in two acrylic groups was greater than the control and less than the Co-Cr group. The formation of fibrotic capsule, except in the acrylic resin with Al2O3 group, increased over time. Clinical Significance Co-Cr alloys are toxic and can produce damage to living tissue. Heat cure acrylic resin materials have less toxicity, and their use is safer than Co-Cr alloys. Citation Ebadian B, Razavi M, Soleimanpour S, Mosharraf R. Evaluation of Tissue Reaction to Some Denture-base Materials: An Animal Study. J Contemp Dent Pract 2008 May; (9)4:067-074.

scholarly journals Antimicrobial and mechanical acrylic resin properties with silver particles obtained from Fusarium oxysporum

2018 ◽  
Vol 21 (1) ◽  
pp. 96 ◽  
Author(s):  
Tabata Prado Sato ◽  
Celio Ilidio Conjo ◽  
Rodnei Dennis Rossoni ◽  
Juliana Campos Junqueira ◽  
Renata Marques de Melo ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Fusarium Oxysporum ◽  
Biofilm Formation ◽  
Antimicrobial Agents ◽  
Acrylic Resin ◽  
Control Group ◽  
Significant Difference ◽  
Color Alteration ◽  
Cie Lab

<p><strong>Objective: </strong>This study evaluated the effects of the incorporation of silver nanoparticles (AgNPs) obtained from <em>Fusarium oxysporum</em> on heat-activated acrylic resin (HAAR) and their influence on resin’s surface roughness, hardness, color alteration and antimicrobial capacity against <em>Candida albicans</em>. <strong>Material and Methods:</strong> For this, 50 discs of HAAR (2x5 mm) were produced and divided into three groups, Control: HAAR; Ag1: HAAR plus 0.539 mg of AgNPs; and Ag2: HAAR plus 1.1 mg of AgNPs. Knopp hardness (HK), surface roughness (Ra and Rz) and color alteration according to the CIE Lab were measured. Specimens were then evaluated <em>in vitro</em> with regard to <em>C. albicans</em> biofilm formation through formed colony count (CFU/mL). Scanning Electron Microscopy (SEM) and Atomic force microscopy (AFM) analyses were performed. <strong>Results:<em> </em></strong>The addition of AgNPs of both concentrations changed Ra, Rz and HK significantly. There was statistically significant difference for L (p=0.00); a*(p=0.00) and b*(p=0.00) parameters. There were no differences between Ag1 and Ag2 biofilm formation, but the comparison of both with the control group presented a significant reduction (p=0.0091) on biofilm formation. SEM and AFM images showed no signs of NPs clustering. <strong>Conclusion:</strong> It can be concluded tha AgNPs incorporation in HAAR was effective in reducing <em>C. albicans</em> activity, with a slight change in color and hardness of the material, being effective therefore, in regions such as the dental prostheses palate, which have lesser aesthetic appeal.</p><p><strong>Keywords</strong></p><p>Acrylic resins; Silver; Antimicrobial agents.</p>

Scanning Electron Microscopy and Roughness Study of Dental Composite Degradation

2012 ◽  
Vol 18 (2) ◽  
pp. 289-294 ◽  
Author(s):  
Luís Eduardo Silva Soares ◽  
Louise Ribeiro Cortez ◽  
Raquel de Oliveira Zarur ◽  
Airton Abrahão Martin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Surface Roughness ◽  
Composite Resin ◽  
Morphological Changes ◽  
Soft Drink ◽  
Dental Composite ◽  
Control Group ◽  
Significant Difference ◽  
Scanning Electron

AbstractOur aim was to test the hypothesis that the use of mouthwashes, consumption of soft drinks, as well as the type of light curing unit (LCU), would change the surface roughness (Ra) and morphology of a nanofilled composite resin (Z350® 3M ESPE). Samples (80) were divided into eight groups: Halogen LCU, group 1, saliva (control); group 2, Pepsi Twist®; group 3, Listerine®; group 4, Colgate Plax®; LED LCU, group 5, saliva; group 6, Pepsi Twist®; group 7, Listerine®; group 8, Colgate Plax®. Ra values were measured at baseline, and after 7 and 14 days. One specimen of each group was prepared for scanning electron microscopy analysis after 14 days. The data were subjected to multifactor analysis of variance at a 95% confidence followed by Tukey's honestly significant difference post-hoc test. All the treatments resulted in morphological changes in composite resin surface, and the most significant change was in Pepsi Twist® groups. The samples of G6 had the greatest increase in Ra. The immersion of nanofilled resin in mouthwashes with alcohol and soft drink increases the surface roughness. Polymerization by halogen LCU (reduced light intensity) associated with alcohol contained mouthwash resulted in significant roughness on the composite.

scholarly journals Antibiofilm and Protein-Repellent Polymethylmethacrylate Denture Base Acrylic Resin for Treatment of Denture Stomatitis

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1067
Author(s):  
Salwa O. Bajunaid ◽  
Bashayer H. Baras ◽  
Abdulrahman A. Balhaddad ◽  
Michael D. Weir ◽  
Hockin H. K. Xu
Keyword(s):  
Surface Roughness ◽  
Acrylic Resin ◽  
Control Group ◽  
Solution Ph ◽  
Biofilm Growth ◽  
Denture Base ◽  
Denture Stomatitis ◽  
Colony Forming Unit ◽  
Microbial Infections ◽  
Unit Reduction

Candida albicans (C. albicans) biofilm is a common etiological factor in denture stomatitis. The purpose of this study was to investigate the effects of incorporating 2-methacryloyloxyethyl phosphorylcholine (MPC) as a protein repellent into a new high-impact denture acrylic (HIPA) resin on the surface roughness, solution pH, and C. albicans biofilm adhesion to the denture base. The new acrylic denture resin base was formulated by mixing MPC into HIPA resin at mass fractions of 1.5%, 3%, and 4.5%. Surface roughness was measured using a Mitutoyo surface roughness tester. C. albicans biofilm growth and viability were assessed via colony forming unit counts. The pH of the biofilm growth medium was measured using a digital pH meter. Adding MPC to the HIPA resin at percentages of 1.5% and 3% increased the roughness values significantly (p < 0.05), while adding 4.5% MPC resulted in no difference in roughness values to that of the control group (p > 0.05). All experimental groups demonstrated neutral pH values (pH ≅ 7) and were not significantly different from each other (p > 0.05). Incorporating 2-methacryloyloxyethyl phosphorylcholine at 4.5% resulted in a significant (≅1 log) colony-forming unit reduction compared with the control group with 0% MPC (p < 0.05). A fungal-retarding denture acrylic resin was developed through the incorporation of MPC for its protein-repelling properties. This newly developed denture acrylic material has the potential to prevent oral microbial infections, such as denture stomatitis.

scholarly journals Variations in Flexural Strength of Heat-polymerized Acrylic Resin after the Usage of Denture Cleansers

2016 ◽  
Vol 17 (4) ◽  
pp. 322-326 ◽  
Author(s):  
M Kalavathi ◽  
Mallikarjuna Ragher ◽  
G Vinayakumar ◽  
Sanketsopan Patil ◽  
Aishwarya Chatterjee ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Testing Machine ◽  
Peak Load ◽  
Acrylic Resin ◽  
Control Group ◽  
Denture Base ◽  
Acrylic Resins ◽  
Significant Difference ◽  
Base Resin ◽  
Denture Cleansers

ABSTRACT Objective The objective of this study was to evaluate and compare changes in the flexural strength of heat-cured denture base resins when treated using denture cleansers. Study design A total of 40 specimens with dimension 65 mm length, 10 mm width, and 3 mm thickness were prepared as per ISO 1567 specification. A total of 10 specimens were immersed in distilled water to be used as control. Of the remaining 30 samples, 10 were treated with Clinsodent, 10 with VI-Clean, and 10 with Clanden denture cleansers. Specimens in each group were subjected to three-point flexural load in universal testing machine at a cross-head speed of 5 mm/min. The peak load (N) was recorded and flexural strength was calculated. The findings were analyzed using Kruskal–Wallis analysis of variance and Mann–Whitney test. Results Heat-cured denture base resin selected for this study showed significant difference in flexural strength after immersion in denture cleansers Clinsodent, VI-Clean, and Clanden solutions, when compared with the control group. Conclusion Findings of this study showed that denture cleansers altered the flexural strength of heat polymerized acrylic resins that endured soaking cycles which simulated 180 days of use. Hence, denture cleansers should be used with caution, once a day after brushing the dentures. It is advisable for patients to follow the manufacturer's instructions. How to cite this article Ragher M, Vinayakumar G, Patil S, Chatterjee A, Mallikarjuna DM, Dandekeri S, Swetha V, Pradeep MR. Variations in Flexural Strength of Heat-polymerized Acrylic Resin after the Usage of Denture Cleansers. J Contemp Dent Pract 2016;17(4):322-326.

scholarly journals PENGARUH PENAMBAHAN ZIRKONIUM OKSIDA DAN SERAT POLIPROPILEN TERHADAP KEKUATAN IMPAK DAN TRANSVERSAL BAHAN BASIS GIGI TIRUAN RESIN AKRILIK POLIMERISASI PANAS

2018 ◽  
Vol 12 (2) ◽  
pp. 177-182
Author(s):  
Eddy Dahar ◽  
Raudhatul Husna
Keyword(s):  
Polypropylene Fiber ◽  
Acrylic Resin ◽  
Mean Value ◽  
Zro2 Nanoparticles ◽  
Control Group ◽  
Denture Base ◽  
Transverse Strength ◽  
Significant Difference ◽  
The Mean ◽  
The Impact

Heat polymerized acrylic resin is the most common material used for making denture base because of it’s advantages. However, this material still hasn’t fulfill all the ideal requirements as a denture base. Some disadvantages that need to be fixed are low impact and transverse strength causing an easy base of fracture. Several attempts were made to improve the mechanical properties of heat polymerized acrylic resin materials by adding reinforcing materials. Zirconium oxide is one of chemical group that can be used as a reinforcing material and polypropylene fiber which is including in fiber reinforcing groups. This study aims to determine whether there is a difference in the effect of the addition of 5% ZrO2 nanoparticles and 2% chopped polypropylene fibers 6 mm in length on the impact and transverse strength of heat polymerized acrylic resin denture base material. The design of this study is a laboratory experimental and the number of samples in this study are 60 samples. The result of this study shows the mean value of the impact and transverse strength of heat polymerized acrylic resin with ZrO2 nanoparticles reinforced is greater than the control group and heat polymerized acrylic resin group with polypropylene fiber reinforced with significant difference, and the mean value of impact and transverse strength of heat polymerized acrylic resin with polypropylene fibers reinforced is greater than the control group with significant difference.

scholarly journals Effect of nano silica coating concentration on reducing acrylic resin denture cytotoxicity

2020 ◽  
Vol 5 (3) ◽  
pp. 126
Author(s):  
Gene Rizky Natalia Gunawan ◽  
Titik Ismiyati ◽  
Haryo Mustiko Dipoyono
Keyword(s):  
Cell Viability ◽  
Base Material ◽  
Acrylic Resin ◽  
Silica Coating ◽  
Control Group ◽  
Nano Silica ◽  
Residual Monomer ◽  
Denture Base ◽  
Significant Difference ◽  
Monomer Content

Acrylic resin is a denture base material mostly used in the fabrication of removable partial denture and complete denture because it is easy to process, economical and aesthetically satisfying. However, the acrylic resin has a weakness i.e. residual monomer content which causes cytotoxic effect to human cells. Nano-silica coating could be used on the acrylic resin to reduce residual monomer content. The purpose of this study was to determine the effect of nano-silica coating concentration on the cytotoxicity of acrylic resin denture base material. Twenty-four acrylic resin disc-shaped specimens (5 mm in diameter and 2 mm in thickness) were divided into 4 groups (n=6), i.e. control, group with application of 0.5%,1%, and 2% nano silica coating. The specimens on the silica coating groups were silica coated using dip-coating method. After the coating was completed, the specimens were added into cell fibroblast culture (vero cell line). Cytotoxicity testswere done by MTT assay. The optical density was measured using ELISA plate reader to determine the percentage of cell viability. The highest mean of cell viability was shown in 0.5% concentration (96.78 ± 1.71) and the lowest mean was shown in the control group (80.32 ± 6.53). One-way ANOVA showed that there were significant differences among these groups. LSD tests showed that there was significant difference among all of the groups. This study concluded that nano silica coating concentration has a significant effect on the cytotoxicity of acrylic resin denture base materials.

IMPACT STRENGTH TEST ON ADDITION OF AGAVE SISALANA FIBER AND E-GLASS FIBER IN ACRYLIC RESIN DENTAL PLATE REPAIR

2021 ◽  
Vol 17 (1) ◽  
pp. 49-55
Author(s):  
Ni Kadek Sugianitri ◽  
◽  
Suhendra Suhendra ◽  
Keyword(s):  
Impact Strength ◽  
Glass Fiber ◽  
Acrylic Resin ◽  
Control Group ◽  
Denture Base ◽  
Denture Plate ◽  
Significant Difference ◽  
The Impact ◽  
Agave Sisalana ◽  
Fiber Addition

Introduction: Acrylic resin is the most common material for the denture base because the acrylic resin has good esthetics, ease of processing, reparability, and inexpensive. A disadvantage of acrylic resin is that it is easy to be cracked. One of the ways to resolve this problem is by adding agave sisalana fiber and E-glass fiber. The purpose of this study was to find out the effect of the addition of agave sisalana fiber and E-glass fiber on the impact strength of an acrylic resin denture plate reparation. Material and Method: The experiment involved twenty-seven plates of heat-cured acrylic with the dimensions of 55x 10 x 10 mm with the 26 x 5 x 4 mm for the cavity to measure, each measurement divided into three groups, with nine samples for each group. The first group was a control group (without fiber), the second group was a group with agave sisalana fiber addition, the third group was a group with e-glass fiber addition. All plates were soaked in distillation water for one day at 37o C. Plates were tested for impact strength using the Charpy method. All data obtained were analyzed with one-way ANOVA followed by LSD (Least Significant Difference) with p<0,05. Result and Discussion: The result showed that the influences of impact strength between without fiber with agave sisalana fiber and E-glass fiber addition on acrylic denture reparation. Acrylic denture reparation in both fibers with concentration 3,3%, agave sisalana fiber has the highest impact strength rather than e-glass fiber. Conclusion: The conclusion of this study is that there is an increase in impact strength with agave sisalana fiber and E-glass fiber addition on acrylic denture reparation and agave sisalana fiber has the highest impact strength.

Sign in / Sign up

Export Citation Format

Share Document