scholarly journals Sintering and Characterization of SiC Reinforced Ni Powders in Microwave Furnace

2020 ◽  
pp. 83-89
Author(s):  
AHMET YONETKEN ◽  
AYHAN EROL
Keyword(s):  
Microwave Furnace

scholarly journals Production and Characterization Of Electroless Ni Coated Fe-Co Composite Using Powder Metallurgy In Microwave Furnace

2021 ◽  
Author(s):  
Assoc. Prof. Dr. Ahmet YONETKEN
Keyword(s):  
Structural Data ◽  
Metallic Phase ◽  
Neutral Atmosphere ◽  
X Ray Diffraction ◽  
Electroless Coating ◽  
Microwave Furnace ◽  
Furnace Sintering ◽  
Atmosphere Environment ◽  
Electroless Ni

Abstract The specimens, magnetic properties materials, and microwave characteristics of Ni coated Fe and Co composites were researched by specimens produced by microwave furnace sintering at 1100°C temperature. A uniform nickel deposit on Fe-Co particles was coated previously to sintering by electroless coating deposition procedure. A composite consisting of quaternary additions, a metallic phase, Fe-Co inside of Ni matrix has been prepared under in a neutral atmosphere environment then microwave sintered. X-Ray Diffraction, SEM(Scanning-Electron-Microscope), Empedans Phase Analyzer were utilized to obtain structural data and to determine magnetic and electrical features such as dielectric and conductivity at the temperature range of 25-400C. The ferromagnetic resonance varied from 10 Hz to 1GHz and measurements were employed to characterize the features of the specimens. Empirical of findings obtained for the composition (Fe-%25Co)50Ni at 1100°C recommend that the best conductivity and hardness were obtained with 50Ni addition at a sintering temperature of 1100°C.

Synthesis and characterization of microinductor made of NiCuZn nanoferrite

2015 ◽  
Vol 29 (29) ◽  
pp. 1550176 ◽  
Author(s):  
Sontosh Kumar ◽  
W. Madhuri ◽  
S. Kalainathan
Keyword(s):  
Mechanical Stress ◽  
Magnetic Semiconductors ◽  
Sol Gel ◽  
Applied Pressure ◽  
Ferrite Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Stress Sensors ◽  
Microwave Furnace

The objective of mechanical stress sensor is to measure the applied pressure or provide control standard to the process. In order to accomplish this, most of the stress sensors convert mechanical stress into electronic signal. Ferrites are the best known magnetic semiconductors. This paper brings out the variation in inductance of the micro-inductor made from [Formula: see text] on application of mechanical stress. [Formula: see text] ferrite nanoparticles are synthesized by sol–gel autocombustion technique. The ferrite powder thus obtained is double sintered at 450[Formula: see text]C and 870[Formula: see text]C in a microwave furnace. The X-ray diffraction pattern of the ferrite confirms spinal structure. The frequency spectrum of dielectric constant is done in the range of 100 to 5 MHz frequency. The variation of inductance [Formula: see text]% with applied compressive stress on the micro-inductor made from the ferrite is measured in the range of 0–8 MPa.

Synthesis and Characterization of NaNbO3 Mesostructure by a Microwave-Assisted Hydrothermal Method

2014 ◽  
Vol 1675 ◽  
pp. 145-150
Author(s):  
Guilhermina F. Teixeira ◽  
Maria Ap. Zaghete ◽  
José A. Varela ◽  
Elson Longo
Keyword(s):  
Hydrothermal Method ◽  
Ferroelectric Property ◽  
Remnant Polarization ◽  
Intermediate Phase ◽  
Synthesis And Characterization ◽  
Synthesis Time ◽  
Microwave Assisted ◽  
Microwave Furnace

ABSTRACTIn the present work, we report the synthesis and characterization of NaNbO3 particles obtained by microwave-assisted hydrothermal method from Nb2O5 and NaOH. The synthesis was made at different periods at 180 °C and 300W. The crystallization of NaNbO3 structures produced Na2Nb2O6.H2O in the intermediate phase with fiber-like morphology, and this is associated with the synthesis time. Pure orthorhombic NaNbO3 with cube-like morphology originates after synthesizing for 240 minutes. To verify the remnant polarization of particles, films were obtained by electrophoresis process and sintered at 800°C for 10 minutes in a microwave furnace. The films characterization indicated that films of niobate with fiber-like morphology present remaining polarization, and the morphology of cubes did not show remaining polarization. Considering these results, it can be concluded that the morphology implemented ferroelectric property of NaNbO3.

Morphological Characterization of Mycobacteriophage R1

1974 ◽  
Vol 32 ◽  
pp. 254-255
Author(s):  
B. L. Soloff ◽  
T. A. Rado
Keyword(s):  
Carbon Source ◽  
Stationary Phase ◽  
Growth Phase ◽  
Minimal Medium ◽  
Morphological Characterization ◽  
Logarithmic Growth Phase ◽  
Complete Lysis ◽  
Lysogenic Culture ◽  
Logarithmic Growth

Mycobacteriophage R1 was originally isolated from a lysogenic culture of M. butyricum. The virus was propagated on a leucine-requiring derivative of M. smegmatis, 607 leu−, isolated by nitrosoguanidine mutagenesis of typestrain ATCC 607. Growth was accomplished in a minimal medium containing glycerol and glucose as carbon source and enriched by the addition of 80 μg/ ml L-leucine. Bacteria in early logarithmic growth phase were infected with virus at a multiplicity of 5, and incubated with aeration for 8 hours. The partially lysed suspension was diluted 1:10 in growth medium and incubated for a further 8 hours. This permitted stationary phase cells to re-enter logarithmic growth and resulted in complete lysis of the culture.

AEM analysis of crystallization in Ti-based amorphous alloys

1983 ◽  
Vol 41 ◽  
pp. 270-271
Author(s):  
A.R. Pelton ◽  
A.F. Marshall ◽  
Y.S. Lee
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Amorphous Materials ◽  
Isothermal Annealing ◽  
Amorphous Matrix ◽  
Nucleation And Growth ◽  
Current Interest ◽  
Amorphous Films ◽  
Electrical And Magnetic Properties

Amorphous materials are of current interest due to their desirable mechanical, electrical and magnetic properties. Furthermore, crystallizing amorphous alloys provides an avenue for discerning sequential and competitive phases thus allowing access to otherwise inaccessible crystalline structures. Previous studies have shown the benefits of using AEM to determine crystal structures and compositions of partially crystallized alloys. The present paper will discuss the AEM characterization of crystallized Cu-Ti and Ni-Ti amorphous films.Cu60Ti40: The amorphous alloy Cu60Ti40, when continuously heated, forms a simple intermediate, macrocrystalline phase which then transforms to the ordered, equilibrium Cu3Ti2 phase. However, contrary to what one would expect from kinetic considerations, isothermal annealing below the isochronal crystallization temperature results in direct nucleation and growth of Cu3Ti2 from the amorphous matrix.

Characterization of Coherent, Ordered Precipitates in Nickel-Base Alloys

1973 ◽  
Vol 31 ◽  
pp. 144-145
Author(s):  
B. H. Kear ◽  
J. M. Oblak
Keyword(s):  
Stable Phase ◽  
Nickel Base Superalloy ◽  
Alloy 718 ◽  
Commercial Alloy ◽  
Precipitate Morphology ◽  
Continuous Precipitation ◽  
Nickel Base ◽  
Base Superalloy ◽  
Strengthening Precipitate

A nickel-base superalloy is essentially a Ni/Cr solid solution hardened by additions of Al (Ti, Nb, etc.) to precipitate a coherent, ordered phase. In most commercial alloy systems, e.g. B-1900, IN-100 and Mar-M200, the stable precipitate is Ni3 (Al,Ti) γ′, with an LI2structure. In A lloy 901 the normal precipitate is metastable Nis Ti3 γ′ ; the stable phase is a hexagonal Do2 4 structure. In Alloy 718 the strengthening precipitate is metastable γ″, which has a body-centered tetragonal D022 structure.Precipitate MorphologyIn most systems the ordered γ′ phase forms by a continuous precipitation re-action, which gives rise to a uniform intragranular dispersion of precipitate particles. For zero γ/γ′ misfit, the γ′ precipitates assume a spheroidal.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

Skeletal elements of crinoid echinoderms: High-resolution structural and microanalytical results

1983 ◽  
Vol 41 ◽  
pp. 194-195
Author(s):  
D. F. Blake ◽  
L. F. Allard ◽  
D. R. Peacor
Keyword(s):  
High Resolution ◽  
Marine Invertebrates ◽  
Sea Urchins ◽  
Structural Features ◽  
Sea Stars ◽  
High Resolution Tem ◽  
Relationship Of ◽  
The Relationship ◽  
Insight Into

Echinodermata is a phylum of marine invertebrates which has been extant since Cambrian time (c.a. 500 m.y. before the present). Modern examples of echinoderms include sea urchins, sea stars, and sea lilies (crinoids). The endoskeletons of echinoderms are composed of plates or ossicles (Fig. 1) which are with few exceptions, porous, single crystals of high-magnesian calcite. Despite their single crystal nature, fracture surfaces do not exhibit the near-perfect {10.4} cleavage characteristic of inorganic calcite. This paradoxical mix of biogenic and inorganic features has prompted much recent work on echinoderm skeletal crystallography. Furthermore, fossil echinoderm hard parts comprise a volumetrically significant portion of some marine limestones sequences. The ultrastructural and microchemical characterization of modern skeletal material should lend insight into: 1). The nature of the biogenic processes involved, for example, the relationship of Mg heterogeneity to morphological and structural features in modern echinoderm material, and 2). The nature of the diagenetic changes undergone by their ancient, fossilized counterparts. In this study, high resolution TEM (HRTEM), high voltage TEM (HVTEM), and STEM microanalysis are used to characterize tha ultrastructural and microchemical composition of skeletal elements of the modern crinoid Neocrinus blakei.

Some applications of electron beam microanalysis techniques in VLSI process evaluation

1983 ◽  
Vol 41 ◽  
pp. 160-161
Author(s):  
Simon Thomas
Keyword(s):  
Integrated Circuits ◽  
Process Evaluation ◽  
Large Scale ◽  
Technology Development ◽  
Analytical Techniques ◽  
Successful Implementation ◽  
Analysis Of Failures ◽  
Characterization Of Materials ◽  
Circuits Vlsi

Trends in the technology development of very large scale integrated circuits (VLSI) have been in the direction of higher density of components with smaller dimensions. The scaling down of device dimensions has been not only laterally but also in depth. Such efforts in miniaturization bring with them new developments in materials and processing. Successful implementation of these efforts is, to a large extent, dependent on the proper understanding of the material properties, process technologies and reliability issues, through adequate analytical studies. The analytical instrumentation technology has, fortunately, kept pace with the basic requirements of devices with lateral dimensions in the micron/ submicron range and depths of the order of nonometers. Often, newer analytical techniques have emerged or the more conventional techniques have been adapted to meet the more stringent requirements. As such, a variety of analytical techniques are available today to aid an analyst in the efforts of VLSI process evaluation. Generally such analytical efforts are divided into the characterization of materials, evaluation of processing steps and the analysis of failures.

Irradiation behavior of pyrolytic silicon carbide

1983 ◽  
Vol 41 ◽  
pp. 72-73
Author(s):  
R. J. Lauf
Keyword(s):  
Silicon Carbide ◽  
Fission Products ◽  
Thermodynamics And Kinetics ◽  
Neutron Fluences ◽  
Fuel Particles ◽  
Sic Coatings ◽  
Irradiation Behavior ◽  
Kinetics Of ◽  
Htgr Fuel

Fuel particles for the High-Temperature Gas-Cooled Reactor (HTGR) contain a layer of pyrolytic silicon carbide to act as a miniature pressure vessel and primary fission product barrier. Optimization of the SiC with respect to fuel performance involves four areas of study: (a) characterization of as-deposited SiC coatings; (b) thermodynamics and kinetics of chemical reactions between SiC and fission products; (c) irradiation behavior of SiC in the absence of fission products; and (d) combined effects of irradiation and fission products. This paper reports the behavior of SiC deposited on inert microspheres and irradiated to fast neutron fluences typical of HTGR fuel at end-of-life.

Sign in / Sign up

Export Citation Format

Share Document