scholarly journals Anti-adherent Molds Yield Hydraulic Concrete Samples Suitable for Assessments of Surface and Water Absorption

2021 ◽  
Vol 10 (4) ◽  
pp. 245-252
Author(s):  
Ernesto Mora ◽  
Erick Castellón
Keyword(s):  
Water Absorption ◽  
Quality Parameters ◽  
Contact Angles ◽  
Water Diffusion ◽  
Concrete Sample ◽  
Hardened Concrete ◽  
Water Contact ◽  
Hydraulic Concrete

To assess several quality parameters of hydraulic concrete, cubic samples of this material are commonly assembled in engineering laboratories using molds. It is ubiquitous the use of cubic metallic molds of volume 125 cm3; these molds require the application of demolding substances (such as oils) on their surfaces to avoid the adhesion of the final hardened concrete sample to the molds. Despite this common practice suitable for evaluating mechanical traits of the materials, the use of a demolding agent spoils the concrete samples for the assessment of surface and water absorption parameters. To overcome this difficulty, we propose a new anti-adherent cubic mold that requires no demolding agent. The construction of the new mold based on anti-adherent polytetrafluoroethene (PTFE, Teflon®) is described with its use. To assess the claimed advantages of the new anti-adherent molds in testing surface and water diffusion traits of concrete samples, experiments on water contact angles, rates of water absorption and drying were performed on concrete specimens obtained with the classic and the new PTFE molds. It was proved the advantage of the anti-adherent mold over common metallic molds. The use of an oil as demolding agent in the concrete samples assembled in metallic molds produced conspicuous differences of water contact angles and absorption in comparison to clean concrete samples produced with PTFE molds.

Crosslinked waterborne polyurethane with high waterproof performance

2016 ◽  
Vol 7 (23) ◽  
pp. 3913-3922 ◽  
Author(s):  
Fangfang Yu ◽  
Liwei Cao ◽  
Zhaohui Meng ◽  
Naibo Lin ◽  
Xiang Yang Liu
Keyword(s):  
Thermal Properties ◽  
Water Absorption ◽  
Waterborne Polyurethane ◽  
High Water ◽  
Contact Angles ◽  
Water Contact ◽  
Fluorinated Acrylate ◽  
Waterborne Polyurethanes

Fluorinated acrylate and siloxane waterborne polyurethanes with crosslinked structure exhibit low water absorption, high water contact angles, and high mechanical/thermal properties.

Superhydrophobic paper coating containing nonconventional clay

TAPPI Journal ◽  
2010 ◽  
Vol 9 (11) ◽  
pp. 33-40 ◽  
Author(s):  
BEHUDIN (BEKO) MESIC ◽  
CHRISTIAN KUGGE ◽  
LARS JÄRNSTRÖM
Keyword(s):  
Water Absorption ◽  
Cross Sections ◽  
Transmission Rate ◽  
High Water ◽  
Contact Angles ◽  
Water Contact ◽  
Barrier Performance ◽  
Superhydrophobic Paper ◽  
Hydrophobic Clay ◽  
Scanning Electron

Hydrophobic clay fillers have not been widely used in dispersion coatings for linerboard because of the difficulty of dispersing them in water. This work investigated whether hydrophobic clay can be used as filler in barrier dispersion coatings. Hydrophobic clay was compared with conventional clay in terms of coating consolidation, structure, wetting, and barrier performance. All coatings were applied to linerboard sheets made using a laboratory dynamic sheet former. The coated linerboards were examined using scanning electron microscopy and Raman spectroscopy, and were characterized with respect to water absorption, vapor transmission rate, and contact angles. The results show that a coating containing hydrophobic clay provides a superhydrophobic character to paper; i.e., a high water contact angle (150°) and relatively low water absorption. Raman mapping of cross-sections revealed that the latex distribution is uniform in the presence of either conventional clay or hydrophobic clay, and that the distribution of hydrophobic clay tends to be more uniform than conventional clay, which might reflect good mixing and consolidation of hydrophobic clay.

scholarly journals The Effect of Hydroxyl on the Superhydrophobicity of Dodecyl Methacrylate (LMA) Coated Fabrics through Simple Dipping-Plasma Crosslinked Method

Coatings ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1263
Author(s):  
Liyun Xu ◽  
Yu Zhang ◽  
Ying Guo ◽  
Ruiyun Zhang ◽  
Jianjun Shi ◽  
...  
Keyword(s):  
Thermoplastic Polyurethane ◽  
Hydrophobic Effect ◽  
Surface Hydrophobicity ◽  
Contact Angles ◽  
Binding Property ◽  
Interesting Phenomenon ◽  
Water Contact ◽  
Capacitively Coupled ◽  
Pet Fabric ◽  
Dodecyl Methacrylate

In order to obtain stable superhydrophobicity, suitable hydrophobic treatment agents should be selected according to different material properties. In this paper, cotton and poly(ethylene terephthalate) (PET) fabrics were respectively coated with dodecyl methacrylate (LMA) via argon combined capacitively coupled plasma (CCP), and the surface hydrophobicity and durability of the treated cotton and polyester fabrics are also discussed. An interesting phenomenon happened, whereby the LMA-coated cotton fabric (Cotton-g-LMA) had better water repelling and mechanical durability properties than LMA-coated PET fabric (PET-g-LMA), and LMA-coated hydroxyl-grafted PET fabrics (PET fabrics were successively coated with polyethylene glycol (PEG) and LMA, PET-g-PEG & LMA) had a similar performance to cotton fabrics. The water contact angles of Cotton-g-LMA, PET-g-LMA and PET-g-PEG & LMA were 156°, 153° and 155°, respectively, and after 45 washing cycles or 1000 rubbing cycles, the corresponding water contact angles decreased to 145°, 88°, 134° and 146°, 127° and 143°, respectively. Additionally, thermoplastic polyurethane (TPU) and polyamides-6 (PA6) fabrics all exhibited the same properties as the PET fabric. Therefore, the grafting of hydroxyl can improve the hydrophobic effect of LMA coating and the binding property between LMA and fabrics effectively, without changing the wearing comfort.

scholarly journals Effect of Water Ingress on the Mechanical and Chemical Properties of Polybutylene Terephthalate Reinforced with Glass Fibers

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1261
Author(s):  
Catarina S. P. Borges ◽  
Alireza Akhavan-Safar ◽  
Eduardo A. S. Marques ◽  
Ricardo J. C. Carbas ◽  
Christoph Ueffing ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Water Uptake ◽  
Significant Influence ◽  
Water Immersion ◽  
Water Diffusion ◽  
Polybutylene Terephthalate ◽  
Chemical Changes ◽  
Water Ingress ◽  
Effect Of Water

Short fiber reinforced polymers are widely used in the construction of electronic housings, where they are often exposed to harsh environmental conditions. The main purpose of this work is the in-depth study and characterization of the water uptake behavior of PBT-GF30 (polybutylene terephthalate with 30% of short glass fiber)as well as its consequent effect on the mechanical properties of the material. Further analysis was conducted to determine at which temperature range PBT-GF30 starts experiencing chemical changes. The influence of testing procedures and conditions on the evaluation of these effects was analyzed, also drawing comparisons with previous studies. The water absorption behavior was studied through gravimetric tests at 35, 70, and 130 °C. Fiber-free PBT was also studied at 35 °C for comparison purposes. The effect of water and temperature on the mechanical properties was analyzed through bulk tensile tests. The material was tested for the three temperatures in the as-supplied state (without drying or aging). Afterwards, PBT-GF30 was tested at room temperature following water immersion at the three temperatures. Chemical changes in the material were also analyzed through Fourier-transform infrared spectroscopy (FTIR). It was concluded that the water diffusion behavior is Fickian and that PBT absorbs more water than PBT-GF30 but at a slightly higher rate. However, temperature was found to have a more significant influence on the rate of water diffusion of PBT-GF30 than fiber content did. Temperature has a significant influence on the mechanical properties of the material. Humidity contributes to a slight drop in stiffness and strength, not showing a clear dependence on water uptake. This decrease in mechanical properties occurs due to the relaxation of the polymeric chain promoted by water ingress. Between 80 and 85 °C, after water immersion, the FTIR profile of the material changes, which suggests chemical changes in the PBT. The water absorption was simulated through heat transfer analogy with good results. From the developed numerical simulation, the minimum plate size to maintain the water ingress unidirectional was 30 mm, which was validated experimentally.

scholarly journals Polypropylene/Lignin/POSS Nanocomposites: Thermal and Wettability Properties, Application in Water Remediation

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3950
Author(s):  
Abeer Alassod ◽  
Syed Rashedul Islam ◽  
Mina Shahriari Khalaji ◽  
Rogers Tusiime ◽  
Wanzhen Huang ◽  
...  
Keyword(s):  
Organic Liquid ◽  
Contact Angles ◽  
Water Remediation ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Thermally Induced ◽  
Dsc Measurements ◽  
Infrared Measurement ◽  
Oligomeric Silsesquioxane ◽  
Tga And Dsc

Compositing is an interesting strategy that has always been employed to introduce or enhance desired functionalities in material systems. In this paper, sponges containing polypropylene, lignin, and octavinyl-polyhedral oligomeric silsesquioxane (OV-POSS) were successfully prepared via an easy and elegant strategy called thermally induced phase separation (TIPS). To fully explore the behaviour of different components of prepared sponges, properties were characterized by a thermogravimetric analyser (TGA), differential scanning calorimetry (DSC), Fourier transform infrared measurement (FTIR), and scanning electron microscopy (SEM). Furthermore, wettability properties toward an organic liquid and oil were investigated. The FTIR analysis confirmed the chemical modification of the components. TGA and DSC measurements revealed thermal stability was much better with an increase in OV-POSS content. OV-POSS modified sponges exhibited ultra-hydrophobicity and high oleophilicity with water contact angles of more than 125°. The SEM revealed that POSS molecules acted as a support for reduced surface roughness. Moreover, OV-POSS-based blend sponges showed higher sorption capacities compared with other blend sponges without OV-POSS. The new blend sponges demonstrated a potential for use as sorbent engineering materials in water remediation.

scholarly journals Physico-Chemical Characterization and Antimicrobial Properties of Hybrid Film Based on Saponite and Phloxine B

Molecules ◽  
2021 ◽  
Vol 26 (2) ◽  
pp. 325
Author(s):  
Nitin Chandra teja Dadi ◽  
Matúš Dohál ◽  
Veronika Medvecká ◽  
Juraj Bujdák ◽  
Kamila Koči ◽  
...  
Keyword(s):  
Hybrid Film ◽  
Antimicrobial Properties ◽  
Chemical Characterization ◽  
Layered Silicate ◽  
Contact Angles ◽  
Exchange Capacity ◽  
Resistant Bacteria ◽  
Hybrid Films ◽  
Water Contact ◽  
Physico Chemical

This research was aimed at the preparation of a hybrid film based on a layered silicate saponite (Sap) with the immobilized photosensitizer phloxine B (PhB). Sap was selected because of its high cation exchange capacity, ability to exfoliate into nanolayers, and to modify different surfaces. The X-ray diffraction of the films confirmed the intercalation of both the surfactant and PhB molecules in the Sap film. The photosensitizer retained its photoactivity in the hybrid films, as shown by fluorescence spectra measurements. The water contact angles and the measurement of surface free energy demonstrated the hydrophilic nature of the hybrid films. Antimicrobial effectiveness, assessed by the photodynamic inactivation on hybrid films, was tested against a standard strain and against methicillin-resistant bacteria of Staphylococcus aureus (MRSA). One group of samples was irradiated (green LED light; 2.5 h) and compared to nonirradiated ones. S. aureus strains manifested a reduction in growth from 1-log10 to over 3-log10 compared to the control samples with Sap only, and defects in S. aureus cells were proven by scanning electron microscopy. The results proved the optimal photo-physical properties and anti-MRSA potential of this newly designed hybrid system that reflects recent progress in the modification of surfaces for various medical applications.

scholarly journals Bonding of Selected Hardwoods with PVAc Adhesive

2020 ◽  
Vol 11 (1) ◽  
pp. 67
Author(s):  
Ján Iždinský ◽  
Ladislav Reinprecht ◽  
Ján Sedliačik ◽  
Jozef Kúdela ◽  
Viera Kučerová
Keyword(s):  
Adhesion Strength ◽  
Cold Water ◽  
Ph Value ◽  
Water Extract ◽  
Solid Wood ◽  
Contact Angles ◽  
Water Contact ◽  
Ph Values ◽  
Positive Tendency ◽  
The Impact

The bonding of wood with assembly adhesives is crucial for manufacturing wood composites, such as solid wood panels, glulam, furniture parts, and sport and musical instruments. This work investigates 13 hardwoods—bangkirai, beech, black locust, bubinga, ipé, iroko, maçaranduba, meranti, oak, palisander, sapelli, wengé and zebrano—and analyzes the impact of their selected structural and physical characteristics (e.g., the density, cold water extract, pH value, roughness, and wettability) on the adhesion strength with the polyvinyl acetate (PVAc) adhesive Multibond SK8. The adhesion strength of the bonded hardwoods, determined by the standard EN 205, ranged in the dry state from 9.5 MPa to 17.2 MPa, from 0.6 MPa to 2.6 MPa in the wet state, and from 8.5 MPa to 19.2 MPa in the reconditioned state. The adhesion strength in the dry state of the bonded hardwoods was not influenced by their cold water extracts, pH values, or roughness parallel with the grain. On the contrary, the adhesion strength was significantly with positive tendency influenced by their higher densities, lower roughness parameters perpendicular to the grain, and lower water contact angles.

scholarly journals Fabrication of Superhydrophobic Ti–6Al–4V Surfaces with Single-Scale Micotextures by using Two-Step Laser Irradiation and Silanization

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3816
Author(s):  
Haidong He ◽  
Risheng Hua ◽  
Xuan Li ◽  
Chunju Wang ◽  
Xuezhong Ning ◽  
...  
Keyword(s):  
Laser Irradiation ◽  
Laser Fluence ◽  
Rolling Direction ◽  
Contact Angles ◽  
Second Step ◽  
Water Contact ◽  
Single Scale ◽  
The Common ◽  
The Rich ◽  
Hierarchical Multiscale

Laser irradiation is a popular method to produce microtextures on metal surfaces. However, the common laser-produced microtextures were hierarchical (multiscale), which may limit their applicability. In this paper, a method of two-step laser irradiation, combining first-step strong ablation and sequentially second-step gentle ablation, was presented to produce micron-rough surface with single-scale microtextures. The effect of laser fluence on the Ti–6Al–4V surface morphology and wettability were investigated in detail. The morphology results revealed that the microtextures produced using this method gradually evolved from multiscale to single-scale meanwhile from microprotrusions to microholes with increasing the second-step laser fluence from 0.0 to 2.4 J/cm2. The wettability and EDS/XPS results indicated that attributing to the rich TiO2 content and micron roughness produced by laser irradiation, all the two-step laser-irradiated surfaces exhibited superhydrophilicity. In addition, after silanization, all these superhydrophilic surfaces immediately turned to be superhydrophobic with close water contact angles of 155–162°. However, due to the absence of nanotextures, the water-rolling angle on the superhydrophobic surfaces with single-scale microtextures distinctly larger than those with multiscale ones. Finally, using the two-step laser-irradiation method and assisted with silanization, multifunctional superhydrophobic Ti–6Al–4V surfaces were achieved, including self-cleaning, guiding of the water-rolling direction and anisotropic water-rolling angles (like the rice-leaf), etc.

scholarly journals P4VP Modified Zwitterionic Polymer for the Preparation of Antifouling Functionalized Surfaces

Nanomaterials ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 706 ◽  
Author(s):  
Chaoqun Wu ◽  
Yudan Zhou ◽  
Haitao Wang ◽  
Jianhua Hu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Cell Attachment ◽  
Raft Polymerization ◽  
Polymer Brush ◽  
Contact Angles ◽  
Polymerization Process ◽  
Water Contact ◽  
Zwitterionic Polymers ◽  
Ito Glass ◽  
Zwitterionic Polymer

Zwitterionic polymers are suitable for replacing poly(ethylene glycol) (PEG) polymers because of their better antifouling properties, but zwitterionic polymers have poor mechanical properties, strong water absorption, and their homopolymers should not be used directly. To solve these problems, a reversible-addition fragmentation chain transfer (RAFT) polymerization process was used to prepare copolymers comprised of zwitterionic side chains that were attached to an ITO glass substrate using spin-casting. The presence of 4-vinylpyridine (4VP) and zwitterion chains on these polymer-coated ITO surfaces was confirmed using 1H NMR, FTIR, and GPC analyses, with successful surface functionalization confirmed using water contact angle, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) studies. Changes in water contact angles and C/O ratios (XPS) analysis demonstrated that the functionalization of these polymers with β-propiolactone resulted in hydrophilic mixed 4VP/zwitterionic polymers. Protein adsorption and cell attachment assays were used to optimize the ratio of the zwitterionic component to maximize the antifouling properties of the polymer brush surface. This work demonstrated that the antifouling surface coatings could be readily prepared using a “P4VP-modified” method, that is, the functionality of P4VP to modify the prepared zwitterionic polymer. We believe these materials are likely to be useful for the preparation of biomaterials for biosensing and diagnostic applications.

scholarly journals Upcycling of Vine Shoots: Production of Fillers for PHBV-Based Biocomposite Applications

2020 ◽  
Author(s):  
Grégoire David ◽  
Laurent Heux ◽  
Stéphanie Pradeau ◽  
Nathalie Gontard ◽  
Hélène Angellier-Coussy
Keyword(s):  
Water Vapor ◽  
Gas Phase ◽  
Mechanical Performance ◽  
Low Cost ◽  
Water Vapor Permeability ◽  
Contact Angles ◽  
Vapor Permeability ◽  
Water Contact ◽  
Median Diameter ◽  
Cost Of Materials

Abstract This paper aims at investigating the potential of vine shoots (ViSh) upcycling as fillers in novel poly(3-hydroxybutyrate-3-hydroxyvalerate) (PHBV) based biocomposites. ViSh particles of around 50 µm (apparent median diameter) were obtained combining dry grinding processes, and mixed with PHBV using melt extrusion. Thermal stability and elongation at break of biocomposites were reduced with increasing contents of ViSh particles (10, 20 and 30 wt%), while Young’s modulus and water vapor permeability were increased. It was shown that a surface gas-phase esterification allowed to significantly increase the hydrophobicity of ViSh particles (increase of water contact angles from 59° to 114°), leading to a reduction of 27% in the water vapor permeability of the biocomposite filled with 30 wt% of ViSh. The overall mechanical performance was not impacted by gas-phase esterification, demonstrating that the interfacial adhesion between the virgin ViSh particles and the PHBV matrix was already good and that such filler surface treatment was not required in that case. It was concluded that ViSh particles can be interestingly used as low cost fillers in PHBV-based biocomposites to decrease the overall cost of materials.

Sign in / Sign up

Export Citation Format

Share Document