scholarly journals Enhanced Energy Recovery from Food Waste by Co-Production of Bioethanol and Biomethane Process

Fermentation ◽  
2021 ◽  
Vol 7 (4) ◽  
pp. 265
Author(s):  
Teeraya Jarunglumlert ◽  
Akarasingh Bampenrat ◽  
Hussanai Sukkathanyawat ◽  
Chattip Prommuak
Keyword(s):  
Food Waste ◽  
Energy Production ◽  
Maximum Yield ◽  
High Energy ◽  
Primary Objective ◽  
Reducing Sugar ◽  
Raw Material ◽  
Energy Output ◽  
Theoretical Yield ◽  
Gross Energy

The primary objective of this research is to study ways to increase the potential of energy production from food waste by co-production of bioethanol and biomethane. In the first step, the food waste was hydrolysed with an enzyme at different concentrations. By increasing the concentration of enzyme, the amount of reducing sugar produced increased, reaching a maximum amount of 0.49 g/g food waste. After 120 h of fermentation with Saccharomyces cerevisiae, nearly all reducing sugars in the hydrolysate were converted to ethanol, yielding 0.43–0.50 g ethanol/g reducing sugar, or 84.3–99.6% of theoretical yield. The solid residue from fermentation was subsequently subjected to anaerobic digestion, allowing the production of biomethane, which reached a maximum yield of 264.53 ± 2.3 mL/g VS. This results in a gross energy output of 9.57 GJ, which is considered a nearly 58% increase in total energy obtained, compared to ethanol production alone. This study shows that food waste is a raw material with high energy production potential that could be further developed into a promising energy source. Not only does this benefit energy production, but it also lowers the cost of food waste disposal, reduces greenhouse gas emissions, and is a sustainable energy production approach.

scholarly journals Oilseed radish in single- and multi-crop sowings with poaceous crops

2020 ◽  
Vol 50 (2) ◽  
pp. 23-31
Author(s):  
O. T. Andreeva ◽  
N. G. Pilipenko ◽  
L. P. Sidorova ◽  
N. Yu. Kharchenko
Keyword(s):  
Dry Matter ◽  
Field Experiments ◽  
High Energy ◽  
Raw Material ◽  
Laboratory Research ◽  
Forest Steppe ◽  
Dry Matter Content ◽  
Oilseed Radish ◽  
Gross Energy ◽  
Digestible Protein

The results of field and laboratory research for 2015–2017 are presented and analyzed on the cultivation of traditional and uncommon poaceous crops. Recognized varieties of barley, oats, and millet were studied in single-crop sowings and intercropped with a high-protein cabbage crop – oilseed radish. The research was conducted on meadow chernozem mealy-carbonate soil in the forest-steppe zone of Trans-Baikal Territory. Agricultural technology used for fodder crop cultivation was common for this area. The objects of the research were the following varieties: barley Anna, oats Metis, millet Bystroe, oilseed radish Tambovchanka. The experimental work was carried out in accordance with the generally accepted guidelines for field experiments. Poaceous crops and oilseed radish were assessed in terms of their adaptability to growing conditions and their economically valuable characteristics that ensure sustainable production of high-energy feed. In multi-crop agrocenoses of poaceous crops and oilseed radish, the yield increased and the quality of feed raw material improved. The best results of multi-crop sowings were achieved by oats and millet intercropped with oilseed radish. The yield of green mass was 38.8-39.7 t/ha, dry matter content – 4.88-4.90 t/ha, digestible protein – 810820 kg/ha, and gross energy – 46.3-52.2 GJ/ha with availability of digestible protein – 180-186 g per one feed unit. Multi-crop sowings of oats and millet with radish oilseed are more productive than single-crop poaceous agrocenoses in feed units by 1.5-1.7 times, digestible protein by 2.9-3.3 times, gross energy by 1.2-1.6 times, with 10.5-10.7 MJ of exchangeable energy in one kilogram of dry matter.

Assessing desalination as a sustainable alternative using a multiple criteria decision support model

2008 ◽  
Vol 3 (3) ◽  
Author(s):  
M. B. Fernandes ◽  
M. C. Almeida ◽  
A. G. Henriques
Keyword(s):  
Decision Support ◽  
Energy Production ◽  
Fossil Fuels ◽  
Cost Benefit Analysis ◽  
Cost Benefit ◽  
High Energy ◽  
Economic Benefits ◽  
Multiple Criteria ◽  
Water Production ◽  
Decision Support Model

Desalination technologies provide an alternative for potable water production, having significant potential for application where fresh water scarcity exists. Potential benefits have to be balanced with other factors, such as high costs, high energy consumption, and significant environmental impacts, for the understanding of real risks and gains of desalination within the context of integrated water resources management. Multiple factors can be considered when analysing the viability of a desalination project but often a limited approach is used. The complexity in the analysis lies in finding the alternatives that obey to multiple objectives (e.g. reduced environmental impact, social acceptance, less cost associated). In this paper, development of a methodology based on multiple criteria decision support system for the evaluation and ranking the potential of desalination technologies is described and applied to a Portuguese case study. Relevant factors to the selection of desalination technologies were identified using SWOT analysis and the MACBETH (Measuring Attractiveness by a Categorical Based Evaluation Technique) approach was applied. Technical alternatives considered include reverse osmosis and multi-effect desalination (MED), together with energy production by fossil fuels or solar energy. Production of water by conventional approaches was also considered. Results, for non-economic benefits, show higher score for MED solar but, in the cost-benefit analysis, conventional methods of water production have higher ranking since costs of renewable energies are not yet competitive. However, even if not preferred in economic terms, desalination is ranked significantly above the conventional approaches for non-economic criteria.

scholarly journals Tagasaste, leucaena and paulownia: three industrial crops for energy and hemicelluloses production

2021 ◽  
Vol 14 (1) ◽  
Author(s):  
Alberto Palma ◽  
Javier Mauricio Loaiza ◽  
Manuel J. Díaz ◽  
Juan Carlos García ◽  
Inmaculada Giráldez ◽  
...  
Keyword(s):  
Activation Energy ◽  
Acid Hydrolysis ◽  
Energy Production ◽  
Combustion Process ◽  
Operating Conditions ◽  
Raw Material ◽  
Energy Of Combustion ◽  
Increasing Temperature ◽  
Hydrolysis Of ◽  
Chamaecytisus Proliferus

Abstract Background Burning fast-growing trees for energy production can be an effective alternative to coal combustion. Thus, lignocellulosic material, which can be used to obtain chemicals with a high added value, is highly abundant, easily renewed and usually inexpensive. In this work, hemicellulose extraction by acid hydrolysis of plant biomass from three different crops (Chamaecytisus proliferus, Leucaena diversifolia and Paulownia trihybrid) was modelled and the resulting solid residues were used for energy production. Results The influence of the nature of the lignocellulosic raw material and the operating conditions used to extract the hemicellulose fraction on the heat capacity and activation energy of the subsequent combustion process was examined. The heat power and the activation energy of the combustion process were found to depend markedly on the hemicellulose content of the raw material. Thus, a low content in hemicelluloses resulted in a lower increased energy yield after acid hydrolysis stage. The process was also influenced by the operating conditions of the acid hydrolysis treatment, which increased the gross calorific value (GCV) of the solid residue by 0.6–9.7% relative to the starting material. In addition, the activation energy of combustion of the acid hydrolysis residues from Chamaecytisus proliferus (Tagasaste) and Paulownia trihybrid (Paulownia) was considerably lower than that for the starting materials, the difference increasing with increasing degree of conversion as well as with increasing temperature and acid concentration in the acid hydrolysis. The activation energy of combustion of the solid residues from acid hydrolysis of tagasaste and paulownia decreased markedly with increasing degree of conversion, and also with increasing temperature and acid concentration in the acid hydrolysis treatment. No similar trend was observed in Leucaena diversifolia (Leucaena) owing to its low content in hemicelluloses. Conclusions Acid hydrolysis of tagasaste, leucaena and paulownia provided a valorizable liquor containing a large amount of hemicelluloses and a solid residue with an increased heat power amenable to efficient valorization by combustion. There are many potential applications of the hemicelluloses-rich and lignin-rich fraction, for example as multi-components of bio-based feedstocks for 3D printing, for energy and other value-added chemicals.

scholarly journals Celery-derived porous carbon materials for superior performance supercapacitor

2021 ◽  
Author(s):  
Sirui Liu ◽  
Ya ping Xu ◽  
Jinggao Wu ◽  
Jing Huang
Keyword(s):  
Porous Carbon ◽  
Carbon Materials ◽  
High Energy ◽  
Cycle Life ◽  
Superior Performance ◽  
Energy Output ◽  
Next Generation ◽  
Porous Carbon Materials ◽  
Long Cycle Life ◽  
Sustainable Materials

Supercapacitors are of paramount importance for next-generation applications, demonstrating high energy output, an ultra-long cycle life and utilizing green and sustainable materials. Herein, we utilize celery, a common biomass from...

scholarly journals Factors Affecting the Metal Recovery Yield during Induction Melting of Aluminium Swarf

2012 ◽  
Vol 730-732 ◽  
pp. 781-786
Author(s):  
Hélder Puga ◽  
Joaquim Barbosa ◽  
Carlos Silva Ribeiro
Keyword(s):  
Processing Parameters ◽  
High Energy ◽  
Metal Recovery ◽  
Raw Material ◽  
Protective Atmosphere ◽  
Induction Melting ◽  
Recovery Rates ◽  
Recovery Yield ◽  
High Efficient ◽  
Machining Operations

Machining operations of cast parts usually generate considerable amounts of waste in the form of chips (usually 3–5% of the casting weight). Traditionally, swarf is sold to scrapers and remelters, but this option is quite expensive because the selling price is roughly 30% of the acquisition price of the commercial 2nd melt raw material. For most aluminium foundries that incorporate machining operations in their products, reusing aluminium chips as raw material for the melting stocks is perhaps the best option as waste management policy in what concerns to economical and technical aspects. Nevertheless, aluminium swarf is a low density product (0.25 kg/dm3) and is usually covered by a thin film of aluminium oxide and machining fluid. Melting such a product without suitable previous preparation leads to very low metal recovery rates, high energy consumption, gases and smoke generation and very low quality of the final product. During the last years, the authors have developed a high efficient and environmentally friend aluminium swarf recycling technique, using direct incorporation in aluminium melts. The influence of processing parameters, namely melt temperature and holding time, melting atmosphere, swarf briquetting pressure and melting charge composition in the metal recovery yield and dross generation was studied and characterized, and the optimal processing parameters were established. The microstructure of the final product obtained in those conditions was evaluated and is also presented. It is shown that the recycling efficiency depends on the swarf conditioning, the melting technique and the melt treatment methodology. Swarf moisture reduction, induction melting under protective atmosphere and a specially developed degassing technique were found the most important factors influencing the recycling process. By using the developed technique, cast ingots with microstructure and sanity similar to commercially available AlSi12Cu1 2nd melt raw material were successfully obtained with minimal dross formation and metal recovery rates around 90%, without using traditional salts and fluxes.

Analyses and evaluation of the main chemical components in different tobacco (Nicotiana tabacum L.) genotypes

2021 ◽  
Vol 72 (1) ◽  
pp. e389
Author(s):  
M. Camlica ◽  
G. Yaldiz
Keyword(s):  
Fatty Acid ◽  
Crude Oil ◽  
Sugar Content ◽  
Industrial Applications ◽  
Reducing Sugar ◽  
Raw Material ◽  
Chemical Components ◽  
Alternative Source ◽  
Nicotine Content ◽  
Tobacco Seeds

The nicotine, reducing sugar and ion contents from the threshing of tobacco can re-used from the industry. The crude oil and fatty oil compositions of tobacco seeds can be considered as an alternative source of raw material for biodiesel. In this study, the nicotine, reducing sugar content, crude oil, fatty acid composition and ion content were determined in 29 genotypes and 1 cultivar of tobacco. The genetic diversity was determined among the tobacco cultivar and genotypes base on examined properties. The nicotine content varied between 0.10-0.87%, reducing sugar ranged from 9.70-21.30%, crude oil varied between 24.33-47.00% and fatty acid compositions was found in the range of 77.94-100%. Linoleic (13.92-75.04%) and butyric (0.33-64.98%) acids were the major components. Overall, the BSR-5 (52.56 mg/g) and ESR-5 (44.58 mg/g) genotypes exhibited the highest potassium contents and ESR-7 (6.54 mg/g) and ESR-8 (1.28 mg/g) genotypes had the lowest chlorine contents. As a result of this study, the highest nicotine content, reducing sugar and crude oil of tobacco were found in ESR-4, ESR-11 and BSR-5 genotypes, respectively. The dendrogram analysis divided the tobacco into two main groups and most of the same origin genotypes fell into the same group. The results indicated that the different tobacco leaves and seeds can be evaluated as an alternative source in the industry as cigarettes, biodiesel and different industrial applications such as cosmetic, oil paints and varnishes based on their chemical properties.

Loss of the mitochondrial phosphate carrier SLC25A3 induces remodeling of the cardiac mitochondrial protein acylome

2021 ◽  
Author(s):  
Jessica N. Peoples ◽  
Nasab Ghazal ◽  
Duc M. Duong ◽  
Katherine R. Hardin ◽  
Janet R. Manning ◽  
...  
Keyword(s):  
Energy Production ◽  
Mitochondrial Protein ◽  
Atp Synthesis ◽  
High Energy ◽  
Mitochondrial Proteins ◽  
Isocitrate Dehydrogenase 2 ◽  
Signaling Organelles ◽  
Specific Pathway ◽  
Phosphate Carrier

Mitochondria are recognized as signaling organelles because, under stress, mitochondria can trigger various signaling pathways to coordinate the cell's response. The specific pathway(s) engaged by mitochondria in response to mitochondrial energy defects in vivo and in high-energy tissues like the heart are not fully understood. Here, we investigated cardiac pathways activated in response to mitochondrial energy dysfunction by studying mice with cardiomyocyte-specific loss of the mitochondrial phosphate carrier (SLC25A3), an established model that develops cardiomyopathy as a result of defective mitochondrial ATP synthesis. Mitochondrial energy dysfunction induced a striking pattern of acylome remodeling, with significantly increased post-translational acetylation and malonylation. Mass spectrometry-based proteomics further revealed that energy dysfunction-induced remodeling of the acetylome and malonylome preferentially impacts mitochondrial proteins. Acetylation and malonylation modified a highly interconnected interactome of mitochondrial proteins, and both modifications were present on the enzyme isocitrate dehydrogenase 2 (IDH2). Intriguingly, IDH2 activity was enhanced in SLC25A3-deleted mitochondria, and further study of IDH2 sites targeted by both acetylation and malonylation revealed that these modifications can have site-specific and distinct functional effects. Finally, we uncovered a novel crosstalk between the two modifications, whereby mitochondrial energy dysfunction-induced acetylation of sirtuin 5 (SIRT5), inhibited its function. Because SIRT5 is a mitochondrial deacylase with demalonylase activity, this finding suggests that acetylation can modulate the malonylome. Together, our results position acylations as an arm of the mitochondrial response to energy dysfunction and suggest a mechanism by which focal disruption to the energy production machinery can have an expanded impact on global mitochondrial function.

scholarly journals Maximizing Anhydrosugar Production from Fast Pyrolysis of Eucalyptus Using Sulfuric Acid as an Ash Catalyst Inhibitor

Catalysts ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 609 ◽  
Author(s):  
Dongyan Zhang ◽  
Yuyang Fan ◽  
Anqing Zheng ◽  
Zengli Zhao ◽  
Fengyun Wang ◽  
...  
Keyword(s):  
Rank Order ◽  
Maximum Yield ◽  
Fast Pyrolysis ◽  
Value Added ◽  
Gas Chromatography Mass Spectrometry ◽  
Cellulose Content ◽  
Pyrolysis Gas ◽  
X Ray ◽  
Theoretical Yield ◽  
Pure Cellulose

Anhydrosugars, such as levoglucosan (LG), are high value-added chemicals which are mainly derived from fast pyrolysis of pure cellulose. However, fast pyrolysis of raw lignocellulosic biomass usually produces a very low amount of levoglucosan, since alkali and alkaline earth metals (AAEM) present in the ash can serve as the catalysts to inhibit the formation of levoglucosan through accelerating the pyranose ring-opening reactions. In this study, eucalyptus was impregnated with H2SO4 solutions with varying concentrations (0.25–1.25%). The characteristics of ash derived from raw and H2SO4-impregnated eucalyptus were characterized by X-ray fluorescence spectroscopy (XRF) and X-ray diffraction (XRD). The pyrolysis behaviors of raw and H2SO4-impregnated eucalyptus were performed on the thermogravimetric analysis (TGA) and pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS). TG analysis demonstrated that the H2SO4-impregnated eucalyptus produced less char than raw eucalyptus. Py-GC/MS analysis showed that even small amounts of H2SO4 can obviously improve the production of anhydrosugars and phenols and suppressed the formation of carboxylic acids, aldehydes, and ketones from fast pyrolysis of eucalyptus. The rank order of levoglucosan yield from raw and impregnated eucalyptus was raw < 1.25% H2SO4 < 1% H2SO4 < 0.75% H2SO4 < 0.25% H2SO4 < 0.5% H2SO4. The maximum yield of levoglucosan (21.3%) was obtained by fast pyrolysis of eucalyptus impregnated with 0.5% H2SO4, which was close to its theoretical yield based on the cellulose content. The results could be ascribed to that H2SO4 can react with AAEM (e.g., Na, K, Ca, and Mg) and lignin to form lignosulfonate, thus acting as an inhibitor to suppress the catalytic effects of AAEM during fast pyrolysis of eucalyptus.

MAXIMUM SECONDARY ELECTRON YIELDS FROM SEMICONDUCTORS AND INSULATORS

2016 ◽  
Vol 24 (04) ◽  
pp. 1750045 ◽  
Author(s):  
A. G. XIE ◽  
Z. H. LIU ◽  
Y. Q. XIA ◽  
M. M. ZHU
Keyword(s):  
Electron Emission ◽  
Secondary Electron ◽  
Maximum Yield ◽  
Secondary Electron Emission ◽  
High Energy ◽  
Secondary Electrons ◽  
Backscattered Electrons ◽  
Universal Formula ◽  
Yield Formula ◽  
Primary Electrons

Based on the processes and characteristics of secondary electron emission and the formula for the yield due to primary electrons hitting on semiconductors and insulators, the universal formula for maximum yield [Formula: see text] due to primary electrons hitting on semiconductors and insulators was deduced, where [Formula: see text] is the maximum ratio of the number of secondary electrons produced by primary electrons to the number of primary electrons. On the basis of the formulae for primary range in different energy ranges of [Formula: see text], characteristics of secondary electron emission and the deduced universal formula for [Formula: see text], the formulae for [Formula: see text] in different energy ranges of [Formula: see text] were deduced, where [Formula: see text] is the primary incident energy at which secondary electron yields from semiconductors and insulators, [Formula: see text], are maximized to maximum secondary electron yields from semiconductors and insulators, [Formula: see text]; and [Formula: see text] is the maximum ratio of the number of total secondary electrons produced by primary electrons and backscattered electrons to the number of primary electrons. According to the deduced formulae for [Formula: see text], the relationship among [Formula: see text], [Formula: see text] and high-energy back-scattering coefficient [Formula: see text], the formulae for parameters of [Formula: see text] and the experimental data as well as the formulae for [Formula: see text] in different energy ranges of [Formula: see text] as a function of [Formula: see text], [Formula: see text], [Formula: see text] and [Formula: see text] were deduced, where [Formula: see text] and [Formula: see text] are the original electron affinity and the width of forbidden band, respectively. The scattering of [Formula: see text] was analyzed, and calculated [Formula: see text] values were compared with the values measured experimentally. It was concluded that the deduced formulae for [Formula: see text] were found to be universal for [Formula: see text].

Sign in / Sign up

Export Citation Format

Share Document