scholarly journals Investigation of Damage Evolution in Heterogeneous Rock Based on the Grain-Based Finite-Discrete Element Model

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3969
Author(s):  
Shirui Zhang ◽  
Shili Qiu ◽  
Pengfei Kou ◽  
Shaojun Li ◽  
Ping Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Grain Orientation ◽  
Damage Evolution ◽  
Discrete Element ◽  
Uniaxial Tensile ◽  
Tensile Cracks ◽  
Rock Heterogeneity ◽  
Heterogeneous Rock

Granite exhibits obvious meso-geometric heterogeneity. To study the influence of grain size and preferred grain orientation on the damage evolution and mechanical properties of granite, as well as to reveal the inner link between grain size‚ preferred orientation, uniaxial tensile strength (UTS) and damage evolution, a series of Brazilian splitting tests were carried out based on the combined finite-discrete element method (FDEM), grain-based model (GBM) and inverse Monte Carlo (IMC) algorithm. The main conclusions are as follows: (1) Mineral grain significantly influences the crack propagation paths, and the GBM can capture the location of fracture section more accurately than the conventional model. (2) Shear cracks occur near the loading area, while tensile and tensile-shear mixed cracks occur far from the loading area. The applied stress must overcome the tensile strength of the grain interface contacts. (3) The UTS and the ratio of the number of intergrain tensile cracks to the number of intragrain tensile cracks are negatively related to the grain size. (4) With the increase of the preferred grain orientation, the UTS presents a “V-shaped” characteristic distribution. (5) During the whole process of splitting simulation, shear microcracks play the dominant role in energy release; particularly, they occur in later stage. This novel framework, which can reveal the control mechanism of brittle rock heterogeneity on continuous-discontinuous trans-scale fracture process and microscopic rock behaviour, provides an effective technology and numerical analysis method for characterizing rock meso-structure. Accordingly, the research results can provide a useful reference for the prediction of heterogeneous rock mechanical properties and the stability control of engineering rock masses.

Effects of Heat Treatment on Microstructures and Mechanical Properties of Ti-38644 Alloy for Aerospace Fasteners

2018 ◽  
Vol 913 ◽  
pp. 109-117 ◽  
Author(s):  
Qing Yun Zhao ◽  
Si Rui Cheng ◽  
Li Dong Wang ◽  
Li Min Dong ◽  
Feng Lei Liu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Solution Temperature ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Air Cooling ◽  
Β Phase ◽  
Α Phase

The effects of heat treatment on microstructure and mechanical properties of Ti-38644 alloy were investigated by scanning electron microscope (SEM) and transmission electron microscopy (TEM) as well as uniaxial tensile test. The results show that when the solution temperature is lower than 845°C, the microstructure of Ti-38644 alloy is equiaxed β phase with the grain size of 20μm, and the tensile strength is about 960MPa. As raising solution temperature to 860°C, the grain size of Ti-38644 alloy increases to 100μm and the tensile strength decreased to 870MPa. There are a large number of secondary α phase precipitated from the grain boundaries and within grain of β phase undergoing aging treatment. Secondary α phase coarsens with increasing the aging temperature, leading to the decrease of tensile strength. After solution treatment at 815°C for 1.5h, water quenching plus aging at 520°C for 10h, air cooling, Ti-38644 alloy shows a better mechanical property with the tensile strength 1330MPa, elongation and reduction of area 10% and 45% respectively.

Vibratory weld conditioning during gas tungsten arc welding of al 5052 alloy on the mechanical and micro-structural behavior

2020 ◽  
Vol 17 (6) ◽  
pp. 831-836
Author(s):  
M. Vykunta Rao ◽  
Srinivasa Rao P. ◽  
B. Surendra Babu
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Welded Joints ◽  
Great Influence ◽  
Welding Process ◽  
Microstructural Characterization ◽  
Content Type ◽  
Average Grain Size

Purpose Vibratory weld conditioning parameters have a great influence on the improvement of mechanical properties of weld connections. The purpose of this paper is to understand the influence of vibratory weld conditioning on the mechanical and microstructural characterization of aluminum 5052 alloy weldments. An attempt is made to understand the effect of the vibratory tungsten inert gas (TIG) welding process parameters on the hardness, ultimate tensile strength and microstructure of Al 5052-H32 alloy weldments. Design/methodology/approach Aluminum 5052 H32 specimens are welded at different combinations of vibromotor voltage inputs and time of vibrations. Voltage input is varied from 50 to 230 V at an interval of 10 V. At each voltage input to the vibromotor, there are three levels of time of vibration, i.e. 80, 90 and 100 s. The vibratory TIG-welded specimens are tested for their mechanical and microstructural properties. Findings The results indicate that the mechanical properties of aluminum alloy weld connections improved by increasing voltage input up to 160 V. Also, it has been observed that by increasing vibromotor voltage input beyond 160 V, mechanical properties were reduced significantly. It is also found that vibration time has less influence on the mechanical properties of weld connections. Improvement in hardness and ultimate tensile strength of vibratory welded joints is 16 and 14%, respectively, when compared without vibration, i.e. normal weld conditions. Average grain size is measured as per ASTM E 112–96. Average grain size is in the case of 0, 120, 160 and 230 is 20.709, 17.99, 16.57 and 20.8086 µm, respectively. Originality/value Novel vibratory TIG welded joints are prepared. Mechanical and micro-structural properties are tested.

Effect of Composite Master Alloy on Mechanical Properties and Electrochemical Corrosion of ZL101 Alloy

2013 ◽  
Vol 749 ◽  
pp. 407-413
Author(s):  
Hong Xu ◽  
Xin Zhang ◽  
Ji Ping Ren ◽  
Min Peng ◽  
Shi Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Grain Refinement ◽  
Master Alloy ◽  
Mass Fraction ◽  
Electrochemical Corrosion ◽  
Corrosion Performance ◽  
Obvious Effect ◽  
Mechanical Properties And Corrosion

The mechanical properties and corrosion performances of the ZL101 alloy modified by the composite master alloy were investigated. The results showed that the master alloy had not only obvious effect of grain refinement, but also a significant role in refining dendrite grain of ZL101 alloy. The grain size decreased dramatically from 150μm to 62μm when the addition of composite master alloy is up to 0.5%(mass fraction) and the temperature is 720 for 30 minutes,. Its tensile strength and elongation increased by 27% and 42% respectively. The grain refinement of ZL101 alloy decreased its corrosion performance. The morphology of Si changed into globular from needle modified by NaF, instead of AlTiB.

Effect of Li on Mechanical Properties and Electrical Conductivity of the Al–Zn–Cu–Mg Based Alloys

2021 ◽  
Vol 21 (9) ◽  
pp. 4897-4901
Author(s):  
Hyo-Sang Yoo ◽  
Yong-Ho Kim ◽  
Hyeon-Taek Son
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Grain Size ◽  
Tensile Strength ◽  
Spherical Particles ◽  
Al Alloy ◽  
High Angle ◽  
Average Grain Size ◽  
Strength Improvement ◽  
Li Content

In this study, changes in the microstructure, mechanical properties, and electrical conductivity of cast and extruded Al–Zn–Cu–Mg based alloys with the addition of Li (0, 0.5 and 1.0 wt.%) were investigated. The Al–Zn–Cu–Mg–xLi alloys were cast and homogenized at 570 °C for 4 hours. The billets were hot extruded into rod that were 12 mm in diameter with a reduction ratio of 38:1 at 550 °C. As the amount of Li added increased from 0 to 1.0 wt.%, the average grain size of the extruded Al alloy increased from 259.2 to 383.0 µm, and the high-angle grain boundaries (HGBs) fraction decreased from 64.0 to 52.1%. As the Li content increased from 0 to 1.0 wt.%, the elongation was not significantly different from 27.8 to 27.4% and the ultimate tensile strength (UTS) was improved from 146.7 to 160.6 MPa. As Li was added, spherical particles bonded to each other, forming an irregular particles. It is thought that these irregular particles contribute to the strength improvement.

scholarly journals Effects of Gd, Y Content on the Microstructure and Mechanical Properties of Mg-Gd-Y-Nd-Zr Alloy

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 790 ◽  
Author(s):  
Changping Tang ◽  
Kai Wu ◽  
Wenhui Liu ◽  
Di Feng ◽  
Xuezhao Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Solution Treatment ◽  
Age Hardening ◽  
Uniaxial Tensile ◽  
Microstructure And Mechanical Properties ◽  
Shaped Particle ◽  
Zr Alloy ◽  
Non Equilibrium

The effects of Gd, Y content on the microstructure and mechanical properties of Mg-Gd-Y-Nd-Zr alloy were investigated using hardness measurements, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), and uniaxial tensile testing. The results indicate that the alloys in as-cast condition mainly consist of α-Mg matrix and non-equilibrium eutectic Mg5.05RE (RE = Gd, Y, Nd). After solution treatment, the non-equilibrium eutectics dissolved into the matrix but some block shaped RE-rich particles were left at the grain boundaries and within grains. These particles are especially Y-rich and deteriorate the mechanical properties of the alloys. Both the compositions of the eutectic and the block shaped particle were independent of the total Gd, Y content of the alloys, but the number of the particles increases as the total Gd, Y content increases. The ultimate tensile strength increases as the total Gd, Y content decreases. A Mg-5.56Gd-3.38Y-1.11Nd-0.48Zr alloy with the highest ultimate tensile strength of 280 MPa and an elongation of 1.3% was fabricated. The high strength is attributed to the age hardening behavior and the decrease in block shaped particles.

Investigation of Mechanical Properties of Nanostructured Titanium Processed by Warm ECAP Followed Cold Rolling

2014 ◽  
Vol 875-877 ◽  
pp. 63-67 ◽  
Author(s):  
Dinh van Hai ◽  
Nguyen Trong Giang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Cold Rolling ◽  
Room Temperature ◽  
Pure Titanium ◽  
Rolling Process ◽  
Coarse Grain ◽  
Nanostructured Titanium

In this work, ECAP technique was combined with cold rolling process in order to enhance mechanical properties and microstructure of pure Titanium. Coarse grain (CG) Titanium with original grain size of 150 μm had been pressed by ECAP at 425oC by 4, 8 and 12 passes, respectively. This process then was followed by rolling at room temperature with 35%, 55%, and 75% rolling strains. After two steps, mechanical properties such as strength, hardness and microstructure of processed Titanium have been measured. The result indicated significant effect of cold rolling on tensile strength, hardness and microstructure of ECAP-Titanium.

scholarly journals Study of Mechanical Behavior and Microstructure for Low-Hardness P92 Steel

2021 ◽  
Vol 2101 (1) ◽  
pp. 012074
Author(s):  
Weixin Yu ◽  
Zhen Dai ◽  
Jifeng Zhao ◽  
Lulu Fang ◽  
Yiwen Zhang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Maximum Size ◽  
Rapid Decrease ◽  
Laves Phases ◽  
P92 Steel ◽  
A Chain ◽  
The Stability ◽  
Evolution Of Microstructure

Abstract The strength of P92 steel (tensile strength, specified plastic elongation strength) will decrease after its hardness is reduced, ferrite and carbides forming the structure. Carbides of grain size 5-6 are precipitated in the grains and grain boundaries. The martensite lath shape has completely disappeared. M23C6 carbide coarsened obviously, with a maximum size of about 500nm; The Laves phase is also aggregated and coarsened, connecting in a chain shape with a maximum size of more than 500nm. Evolution of microstructure, namely the obvious coarsening of M23C6 carbides and the aggregation and connection of Laves phases in a chain shape, are the main causes for rapid decrease in the stability of the material substructure and evident decline in mechanical properties and hardness. In addition, the MX phase did not change significantly, hardly affecting the hardness reduction of P92 steel.

Microstructure and Mechanical Performance of AZ31-1.7 Wt.% Si Alloy Processed by Cyclic Channel Die Compression

2010 ◽  
Vol 667-669 ◽  
pp. 457-461
Author(s):  
Wei Guo ◽  
Qu Dong Wang ◽  
Man Ping Liu ◽  
Tao Peng ◽  
Xin Tao Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Chinese Script ◽  
Cast State ◽  
Microstructure And Mechanical Properties ◽  
Mean Grain Size ◽  
The Matrix ◽  
The Mean

Cyclic channel die compression (CCDC) of AZ31-1.7 wt.% Si alloy was performed up to 5 passes at 623 K in order to investigate the microstructure and mechanical properties of compressed alloys. The results show that multi-pass CCDC is very effective to refine the matrix grain and Mg2Si phases. After the alloy is processed for 5 passes, the mean grain size decreases from 300 μm of as-cast to 8 μm. Both dendritic and Chinese script type Mg2Si phases break into small polygonal pieces and distribute uniformly in the matrix. The tensile strength increases prominently from 118 MPa to 216 MPa, whereas the hardness of alloy deformed 5 passes only increase by 8.4% compared with as-cast state.

Tensile properties of the FFF-processed thermoplastic polyurethane (TPU) elastomer

2021 ◽  
Author(s):  
Budi Arifvianto ◽  
Teguh Nur Iman ◽  
Benidiktus Tulung Prayoga ◽  
Rini Dharmastiti ◽  
Urip Agus Salim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Low Cost ◽  
Thermoplastic Polyurethane ◽  
High Strength ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Fused Filament Fabrication ◽  
Raster Angle ◽  
Manufacturing Techniques

Abstract Fused filament fabrication (FFF) has become one of the most popular, practical, and low-cost additive manufacturing techniques for fabricating geometrically-complex thermoplastic polyurethane (TPU) elastomer. However, there are still some uncertainties concerning the relationship between several operating parameters applied in this technique and the mechanical properties of the processed material. In this research, the influences of extruder temperature and raster orientation on the mechanical properties of the FFF-processed TPU elastomer were studied. A series of uniaxial tensile tests was carried out to determine tensile strength, strain, and elastic modulus of TPU elastomer that had been printed with various extruder temperatures, i.e., 190–230 °C, and raster angles, i.e., 0–90°. Thermal and chemical characterizations were also conducted to support the analysis in this research. The results obviously showed the ductile and elastic characteristics of the FFF-processed TPU, with specific tensile strength and strain that could reach up to 39 MPa and 600%, respectively. The failure mechanisms operating on the FFF-processed TPU and the result of stress analysis by using the developed Mohr’s circle are also discussed in this paper. In conclusion, the extrusion temperature of 200 °C and raster angle of 0° could be preferred to be applied in the FFF process to achieve high strength and ductile TPU elastomer.

Severe Plastic Deformation-Key Features, Methods and Application

2020 ◽  
Vol 1003 ◽  
pp. 31-36
Author(s):  
Marko Vilotic ◽  
Li Hui Lang ◽  
Sergei Alexandrov ◽  
Dragisa Vilotic
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Tensile Strength ◽  
Severe Plastic Deformation ◽  
Metal Forming ◽  
Good Corrosion Resistance ◽  
Processed Material ◽  
Key Features ◽  
Forming Methods

Compared to conventional metal forming methods, processing by severe plastic deformation is mostly used to improve the mechanical properties and not for the shaping of a product. Processed material usually has an average crystal grain size of less than a micron and as a result, the material exhibits improvements in most of the mechanical properties, such as yield and ultimate tensile strength, microhardness, sufficiently high workability, good corrosion resistance, and implant biocompatibility and others. In this paper, a brief review of the processing by severe plastic deformation was presented, including the benefits, major methods, and the application. Additionally, a brief review of two methods made by authors was made.

Sign in / Sign up

Export Citation Format

Share Document