scholarly journals Influence of Carbon on the Microstructure Evolution and Hardness of Fe–13Cr–xC (x = 0–0.7 wt.%) Stainless Steel

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5063
Author(s):  
Michael Harwarth ◽  
Adam Brauer ◽  
Qiuliang Huang ◽  
Mehdi Pourabdoli ◽  
Javad Mola
Keyword(s):  
Carbon Concentration ◽  
Steady Increase ◽  
Scanning Calorimetry ◽  
Delta Ferrite ◽  
Solidification Mode ◽  
Stability Range ◽  
Austenitic Phase ◽  
Dsc Measurements ◽  
Calculation Results ◽  
Carbon Concentrations

The influence of carbon on the phase transformation behavior of stainless steels with the base chemical composition Fe–13Cr (wt.%), and carbon concentrations in the range of 0–0.7 wt.%, was studied at temperatures between −196 °C and liquidus temperature. Based on differential scanning calorimetry (DSC) measurements, the solidification mode changed from ferritic to ferritic–austenitic as the carbon concentration increased. The DSC results were in fair agreement with the thermodynamic equilibrium calculation results. In contrast to alloys containing nearly 0% C and 0.1% C, alloys containing 0.2–0.7% C exhibited a fully austenitic phase stability range without delta ferrite at high temperatures. Quenching to room temperature (RT) after heat treatment in the austenite range resulted in the partial transformation to martensite. Due to the decrease in the martensite start temperature, the fraction of retained austenite increased with the carbon concentration. The austenite fraction was reduced by cooling to −196 °C. The variation in hardness with carbon concentration for as-quenched steels with martensitic–austenitic microstructures indicated a maximum at intermediate carbon concentrations. Given the steady increase in the tetragonality of martensite at higher carbon concentrations, as confirmed by X-ray diffraction measurements, the variation in hardness with carbon concentration is governed by the amount and stability of austenite.

scholarly journals Traffic Density-Related Black Carbon Distribution: Impact of Wind in a Basin Town

2021 ◽  
Vol 18 (12) ◽  
pp. 6490
Author(s):  
Borut Jereb ◽  
Brigita Gajšek ◽  
Gregor Šipek ◽  
Špela Kovše ◽  
Matevz Obrecht
Keyword(s):  
Black Carbon ◽  
Carbon Concentration ◽  
Ground Level ◽  
Traffic Density ◽  
Carbon Distribution ◽  
Wind Speeds ◽  
Black Carbon Concentration ◽  
Low Wind Speeds ◽  
Temperature Inversions ◽  
Carbon Concentrations

Black carbon is one of the riskiest particle matter pollutants that is harmful to human health. Although it has been increasingly investigated, factors that depend on black carbon distribution and concentration are still insufficiently researched. Variables, such as traffic density, wind speeds, and ground levels can lead to substantial variations of black carbon concentrations and potential exposure, which is even riskier for people living in less-airy sites. Therefore, this paper “fills the gaps” by studying black carbon distribution variations, concentrations, and oscillations, with special emphasis on traffic density and road segments, at multiple locations, in a small city located in a basin, with frequent temperature inversions and infrequent low wind speeds. As wind speed has a significant impact on black carbon concentration trends, it is critical to present how low wind speeds influence black carbon dispersion in a basin city, and how black carbon is dependent on traffic density. Our results revealed that when the wind reached speeds of 1 ms−1, black carbon concentrations actually increased. In lengthy wind periods, when wind speeds reached 2 or 3 ms−1, black carbon concentrations decreased during rush hour and in the time of severe winter biomass burning. By observing the results, it could be concluded that black carbon persists longer in higher altitudes than near ground level. Black carbon concentration oscillations were also seen as more pronounced on main roads with higher traffic density. The more the traffic decreases and becomes steady, the more black carbon concentrations oscillate.

scholarly journals Polypropylene/Lignin/POSS Nanocomposites: Thermal and Wettability Properties, Application in Water Remediation

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3950
Author(s):  
Abeer Alassod ◽  
Syed Rashedul Islam ◽  
Mina Shahriari Khalaji ◽  
Rogers Tusiime ◽  
Wanzhen Huang ◽  
...  
Keyword(s):  
Organic Liquid ◽  
Contact Angles ◽  
Water Remediation ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Thermally Induced ◽  
Dsc Measurements ◽  
Infrared Measurement ◽  
Oligomeric Silsesquioxane ◽  
Tga And Dsc

Compositing is an interesting strategy that has always been employed to introduce or enhance desired functionalities in material systems. In this paper, sponges containing polypropylene, lignin, and octavinyl-polyhedral oligomeric silsesquioxane (OV-POSS) were successfully prepared via an easy and elegant strategy called thermally induced phase separation (TIPS). To fully explore the behaviour of different components of prepared sponges, properties were characterized by a thermogravimetric analyser (TGA), differential scanning calorimetry (DSC), Fourier transform infrared measurement (FTIR), and scanning electron microscopy (SEM). Furthermore, wettability properties toward an organic liquid and oil were investigated. The FTIR analysis confirmed the chemical modification of the components. TGA and DSC measurements revealed thermal stability was much better with an increase in OV-POSS content. OV-POSS modified sponges exhibited ultra-hydrophobicity and high oleophilicity with water contact angles of more than 125°. The SEM revealed that POSS molecules acted as a support for reduced surface roughness. Moreover, OV-POSS-based blend sponges showed higher sorption capacities compared with other blend sponges without OV-POSS. The new blend sponges demonstrated a potential for use as sorbent engineering materials in water remediation.

scholarly journals Effect of weld metal composition on impact toughness properties of shielded metal arc welded ultra-high hard armor steel joints

2020 ◽  
Vol 29 (1) ◽  
pp. 186-194
Author(s):  
V. Balaguru ◽  
Visvalingam Balasubramanian ◽  
P. Sivakumar
Keyword(s):  
Impact Toughness ◽  
Weld Metal ◽  
Welded Joints ◽  
Weight Ratio ◽  
High Hardness ◽  
High Strength ◽  
Solidification Mode ◽  
Austenitic Phase ◽  
Ferrite Number ◽  
Steel Joints

AbstractNowadays, ultra-high hard armor (UHA) steels are employed in armor tracked vehicle (ATV) construction because of their high hardness, high strength to weight ratio, and excellent toughness. UHA steels are usually welded using austenitic stainless steel (ASS) welding consumables, to avoid hydrogen-induced cracking (HIC). The use of ASS consumables to weld the above steel was the only available remedy because of higher solubility of hydrogen in the austenitic phase. In this investigation, an attempt was made to investigate the effect of ASS consumables (with different Creq/Nieq ratio) on solidification mode, impact toughness and microstructural characteristics of shielded metal arc (SMA) welded UHA steel joints. The welded joints were characterised based on impact toughness properties, hardness, and microstructural features. As the ferrite number increases with an increase in Creq/Nieq ratio result in different solidification mode (A, FA, F). It is also found that ferrite number of weld metal has appreciable influence on impact toughness and has inversely proportional relationship with impact toughness of the welded joints.

Investigations on the polymorphism and pseudopolymorphism of clobetasone butyrate

2011 ◽  
Vol 76 (5) ◽  
pp. 553-566
Author(s):  
Christian Näther ◽  
Inke Jeß
Keyword(s):  
Room Temperature ◽  
Polymorphic Form ◽  
Stable Form ◽  
Scanning Calorimetry ◽  
Amorphous Form ◽  
Space Group ◽  
Dsc Measurements ◽  
Independent Molecules ◽  
Solvent Molecules ◽  
Similar Conformation

Clobetasone butyrate was investigated for polymorphism and pseudopolymorphism. Solvent mediated conversion experiments reveal that the commercially available form I represent the thermodynamically most stable form at room temperature and DSC measurements shows that it should also be the most stable form until melting. Form I crystallizes in space groupP212121with three crystallographically independent molecules of similar conformation. From methanol an additional pseudo polymorphic form was discovered. In the crystal structure (space groupP212121) the solvent molecules are connected to the clobetasone butyrate molecules by O–H···O hydrogen bonding. Investigations of the solvate using thermogravimetry, differential thermoanalysis as well as differential scanning calorimetry proves, that on solvent removal an amorphous form is obtained that crystallizes into form I on further heating.

Effects of Aging on the Microstructure and Phase Transformation Behavior of Cu-Al-Mn Shape Memory Alloy

2021 ◽  
Vol 882 ◽  
pp. 21-27
Author(s):  
Seyed Veghar Seyedmohammadi ◽  
Amin Radi ◽  
Guney Guven Yapici
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory ◽  
Aging Treatment ◽  
Scanning Calorimetry ◽  
Dsc Measurements ◽  
Peak Aged Condition ◽  
Peak Aged ◽  
Rolled Condition ◽  
The One ◽  
Effects Of Aging

In the present work, the effects of artificial aging treatment on the transformation temperatures and hardness of Cu-Al-Mn shape memory alloy have been investigated. The aging processes have been performed on the one-time re-melted and 90% rolled samples. Differential scanning calorimetry reveals that reverse transformation is present for the re-melted sample which is aged at 400°C. However, in 90% rolled condition, this transformation takes place at 200°C and 300°C. Hardness examination shows that the aged specimens possess higher values in hardness in comparison to un-aged samples at all studied temperatures. Although, the peak-aged condition was demonstrated at 300°C for the re-melted sample, the rolled sample displayed increased hardness levels up to 500°C. Based on the DSC measurements and microstructural observations, it can be asserted that the thermo-mechanical processing including rolling plus aging at 300°C provides favorable transformation characteristics for shape memory behavior.

scholarly journals A Facile Synthesis and Characterization of Highly Crystalline Submicro-Sized BiFeO3

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 3035
Author(s):  
Dovydas Karoblis ◽  
Diana Griesiute ◽  
Kestutis Mazeika ◽  
Dalis Baltrunas ◽  
Dmitry V. Karpinsky ◽  
...  
Keyword(s):  
Bismuth Ferrite ◽  
Cost Effective ◽  
Xrd Analysis ◽  
Synthetic Approach ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Dsc Measurements ◽  
Optimal Annealing Temperature ◽  
Synthesized Materials

In this study, a highly crystalline bismuth ferrite (BFO) powder was synthesized using a novel, very simple, and cost-effective synthetic approach. It was demonstrated that the optimal annealing temperature for the preparation of highly-pure BFO is 650 °C. At lower or higher temperatures, the formation of neighboring crystal phases was observed. The thermal behavior of BFO precursor gel was investigated by thermogravimetric and differential scanning calorimetry (TG-DSC) measurements. X-ray diffraction (XRD) analysis and Mössbauer spectroscopy were employed for the investigation of structural properties. Scanning electron microscopy (SEM) was used to evaluate morphological features of the synthesized materials. The obtained powders were also characterized by magnetization measurements, which showed antiferromagnetic behavior of BFO powders.

scholarly journals Luminescence of SiO2-BaF2:Tb3+, Eu3+ Nano-Glass-Ceramics Made from Sol–Gel Method at Low Temperature

Nanomaterials ◽  
2022 ◽  
Vol 12 (2) ◽  
pp. 259
Author(s):  
Natalia Pawlik ◽  
Barbara Szpikowska-Sroka ◽  
Tomasz Goryczka ◽  
Ewa Pietrasik ◽  
Wojciech A. Pisarski
Keyword(s):  
Sol Gel ◽  
Three Dimensional ◽  
Glass Ceramics ◽  
Emission Spectra ◽  
Scanning Calorimetry ◽  
Light Emitting ◽  
Co Doping ◽  
Dsc Measurements ◽  
Decay Times

The synthesis and characterization of multicolor light-emitting nanomaterials based on rare earths (RE3+) are of great importance due to their possible use in optoelectronic devices, such as LEDs or displays. In the present work, oxyfluoride glass-ceramics containing BaF2 nanocrystals co-doped with Tb3+, Eu3+ ions were fabricated from amorphous xerogels at 350 °C. The analysis of the thermal behavior of fabricated xerogels was performed using TG/DSC measurements (thermogravimetry (TG), differential scanning calorimetry (DSC)). The crystallization of BaF2 phase at the nanoscale was confirmed by X-ray diffraction (XRD) measurements and transmission electron microscopy (TEM), and the changes in silicate sol–gel host were determined by attenuated total reflectance infrared (ATR-IR) spectroscopy. The luminescent characterization of prepared sol–gel materials was carried out by excitation and emission spectra along with decay analysis from the 5D4 level of Tb3+. As a result, the visible light according to the electronic transitions of Tb3+ (5D4 → 7FJ (J = 6–3)) and Eu3+ (5D0 → 7FJ (J = 0–4)) was recorded. It was also observed that co-doping with Eu3+ caused the shortening in decay times of the 5D4 state from 1.11 ms to 0.88 ms (for xerogels) and from 6.56 ms to 4.06 ms (for glass-ceramics). Thus, based on lifetime values, the Tb3+/Eu3+ energy transfer (ET) efficiencies were estimated to be almost 21% for xerogels and 38% for nano-glass-ceramics. Therefore, such materials could be successfully predisposed for laser technologies, spectral converters, and three-dimensional displays.

Influence of Carbon Concentration as Coating on Electrical Conductivity of LiFeSi0.03P0.97O4/C

2021 ◽  
Vol 1028 ◽  
pp. 185-190
Author(s):  
Hafizhah Ellora Della ◽  
Mochamad Zainuri ◽  
Pelangi Az Zahra ◽  
Puri Olyvia Swastika ◽  
Triwikantoro
Keyword(s):  
Electrical Conductivity ◽  
Carbon Concentration ◽  
Research Study ◽  
Raw Materials ◽  
Carbon Sources ◽  
Xrd Analysis ◽  
Si Doping ◽  
Diffraction Peaks ◽  
Materials Used ◽  
Carbon Concentrations

This research study about the influence of carbon concenttration as coating on electrical conductivity of LiFeSi0.03P0.97O4/C. Synthesis of LiFeSi0.03P0.97O4/C was carried out different carbon concentrations of 7, 9, and 11 wt%. The raw materials used are Fe2O3, Li2CO3, (NH4)2HPO4, SiO2 as ion Si doping, and glucose as carbon sources. The XRD analysis results showed that all the diffraction peaks in samples were the olivine LiFePO4 phase. From the EIS result, Samples with the addition carbon concentration of 9 wt% produce the highest electrical conductivity values of 4.18 x 10-7 S/cm.

Microstructure of Sn-20In-2.8Ag solder and mechanical properties of joint with Cu

2019 ◽  
Vol 31 (1) ◽  
pp. 1-5 ◽  
Author(s):  
Fen Peng ◽  
Wensheng Liu ◽  
Yunzhu Ma ◽  
Chaoping Liang ◽  
Yufeng Huang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Eutectic Reaction ◽  
Scanning Calorimetry ◽  
Good Reliability ◽  
Content Type ◽  
Dsc Measurements ◽  
Lap Shear ◽  
Evolution Characteristics ◽  
Three Phase ◽  
Melting And Solidification

Purpose To explore substitutes for traditional Sn-Pb solder, Sn-20In-2.8Ag was considered because of its appropriate melting temperature, good reliability and high ductility at less than 100°C. However, the mechanical properties of Sn-20In-2.8Ag were not satisfactory. The reason for the poor mechanical properties of the Sn-20In-2.8Ag/Cu joint was revealed, and a way to solve the problem was found. Design/methodology/approach The microstructure evolution, characteristics of melting and solidification and joining performance with Cu were investigated using scanning electron microscopy (SEM), electron probe microanalysis, differential scanning calorimetry (DSC) and mechanical testing. Findings SEM results showed that the microstructure of Sn-20In-2.8Ag was composed of coarse dendritic Ag2In and γ phases, with Ag2In distributed at the grain boundaries. DSC measurements revealed that small amount of low temperature eutectic reaction, L → Ag2In + β + γ, occurred at 112.9°C. This reaction was caused by the segregation of indium, which is a process that has a strong driving force. In the lap-shear testing, a crack propagated along the grain boundary of the solder, and failure showed an intergranular fracture. This failure was connected with the three-phase eutectic and coarse Ag2In. Thus, to improve the mechanical properties, segregation of indium should be reduced and coarsening of Ag2In should be prevented. Originality/value The reason for the unsatisfactory mechanical properties of Sn-20In-2.8Ag was revealed via microstructural observations and solidification analysis, and the way to solve this problem was found.

scholarly journals Structural Characterisation and Mechanical FE Analysis of Conventional and M-Wire Ni-Ti Alloys Used in Endodontic Rotary Instruments

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Diogo Montalvão ◽  
Francisca Sena Alçada ◽  
Francisco Manuel Braz Fernandes ◽  
Sancho de Vilaverde-Correia
Keyword(s):  
Body Temperature ◽  
Mechanical Response ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Austenitic Phase ◽  
X Ray ◽  
Structural Characterisation ◽  
Working Temperature ◽  
Ti Alloys ◽  
Rotary Instruments

The purpose of this study is to understand how the M-Wire alloy conditions the mechanical flexibility of endodontic rotary files at body temperature.Two different rotary instruments, a Profile GT 20/.06 and a Profile GT Series X 20/.06, were selected due to their geometrical similarity and their different constituent alloy. GT series X files are made from M-Wire, a Ni-Ti alloy allegedly having higher flexibility at body temperature. Both files were analysed by X-Ray Diffraction and Differential Scanning Calorimetry to investigate phase transformations and the effects of working temperature on these different alloys. Mechanical behaviour was assessed by means of static bending and torsional Finite Element simulations, taking into account the nonlinear superelastic behaviour of Ni-Ti materials. It was found that GT files present austenitic phase at body temperature, whereas GT series X present R-phase at temperatures under 40°C with a potential for larger flexibility. For the same load conditions, simulations showed that the slight geometrical differences between the two files do not introduce great disagreement in the instruments’ mechanical response. It was confirmed that M-Wire increases the instrument’s flexibility, mainly due to the presence of R-phase at body temperature.

Sign in / Sign up

Export Citation Format

Share Document