scholarly journals Modification of Laser Marking Ability and Properties of Polypropylene Using Silica Waste as a Filler

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6961
Author(s):  
Artur Kościuszko ◽  
Piotr Czyżewski ◽  
Mateusz Rojewski
Keyword(s):  
Laser Beam ◽  
Polymer Matrix ◽  
Tensile Tests ◽  
Degree Of Crystallinity ◽  
Infrared Range ◽  
Scanning Calorimetry ◽  
Multifunctional Additive ◽  
Strong Concentration ◽  
Laser Marking ◽  
Laser Head

Polypropylene (PP) belongs to the group of polymers characterized by low susceptibility to absorption of electromagnetic radiation in the infrared range (λ = 1064 nm). This research consisted of assessing the possibility of using silica waste from the metallurgic industry as an additive for PP laser marking. The modifier was introduced into the polymer matrix in the range from 1 to 10 wt%. The effects of laser radiation were assessed based on colorimetric tests and microscopic surface analysis. The mechanical properties of the composites were determined during the static tensile tests. The thermal properties were investigated via differential scanning calorimetry. It was found that the introduction of silica waste into polypropylene allows for the effective marking of sample surfaces with the use of a laser beam. The greatest contrast between the graphic symbol and the background was obtained for silica contents of 3 and 5 wt%, with the use of a low-speed laser head and a strong concentration of the laser beam. The application of silica caused an increase in the modulus of elasticity and the tensile strength of the composite samples. Increases in the crystallization temperature and the degree of crystallinity of the polymer matrix were also observed. It was found that silica waste can act as multifunctional additive for polypropylene.

Effect of modified microcrystalline cellulose on poly(3-hydroxybutyrate) molecular dynamics by proton relaxometry

2020 ◽  
pp. 096739112092607
Author(s):  
Filipe Antonio dos Santos Viegas Ribeiro ◽  
Maxwell de Paula Cavalcante ◽  
Maria Inês Bruno Tavares ◽  
Amanda Ramos Aragão Melo
Keyword(s):  
Molecular Dynamics ◽  
Polymer Matrix ◽  
Degree Of Crystallinity ◽  
Hybrid Films ◽  
Scanning Calorimetry ◽  
Reciprocal Influence ◽  
Proton Relaxometry ◽  
Solution Casting Method ◽  
Cellulose Concentration ◽  
Modified Cellulose

Hybrid films of poly(3-hydroxybutyrate) (PHB) and modified cellulose by solution casting method were prepared, aiming to study the influence of modified cellulose (0.25%, 0.5% and 0.75% w/w) on the structural organization and thermal properties of PHB matrix. The modified cellulose showed good dispersion in polymer matrix, due to the high compatibility between phases explained by similarity of polymer and filler structures. The composites were studied by wide-angle X-ray diffractometry, differential scanning calorimetry, thermogravimetric analysis, and time-domain nuclear magnetic resonance (NMR) spectroscopy. The conjugation of results coming from those techniques allowed to determine the cellulose concentration that had the highest influence on crystalline planes and degree of crystallinity of PHB, that is, the influence in the composite structure. The molecular dynamics obtained by NMR showed a reciprocal influence between polymer matrix and cellulose particles, enhancing the interactions present in the agglomerated particles.

scholarly journals Influence of the Lignin Content on the Properties of Poly(Lactic Acid)/lignin-Containing Cellulose Nanofibrils Composite Films

Polymers ◽  
2018 ◽  
Vol 10 (9) ◽  
pp. 1013 ◽  
Author(s):  
Xuan Wang ◽  
Yuan Jia ◽  
Zhen Liu ◽  
Jiaojiao Miao
Keyword(s):  
Lactic Acid ◽  
Lignin Content ◽  
Cellulose Nanofibrils ◽  
Composite Films ◽  
Tensile Tests ◽  
Nucleating Agent ◽  
Mechanical Analysis ◽  
Degree Of Crystallinity ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry

Poly(lactic acid) (PLA)/lignin-containing cellulose nanofibrils (L-CNFs) composite films with different lignin contents were produced bythe solution casting method. The effect of the lignin content on the mechanical, thermal, and crystallinity properties, and PLA/LCNFs interfacial adhesion wereinvestigated by tensile tests, thermogravimetric analysis, differential scanning calorimetry (DSC), dynamic mechanical analysis, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). The tensile strength and modulus of the PLA/9-LCNFs (9 wt % lignin LCNFs) composites are 37% and 61% higher than those of pure PLA, respectively. The glass transition temperature (Tg) decreases from 61.2 for pure PLA to 52.6 °C for the PLA/14-LCNFs (14 wt % lignin LCNFs) composite, and the composites have higher thermal stability below 380 °C than pure PLA. The DSC results indicate that the LCNFs, containing different lignin contents, act as a nucleating agent to increase the degree of crystallinity of PLA. The effect of the LCNFs lignin content on the PLA/LCNFs compatibility/adhesion was confirmed by the FTIR, SEM, and Tg results. Increasing the LCNFs lignin content increases the storage modulus of the PLA/LCNFs composites to a maximum for the PLA/9-LCNFs composite. This study shows that the lignin content has a considerable effect on the strength and flexibility of PLA/LCNFs composites.

scholarly journals Influence of Myrrh Extracts on the Properties of PLA Films and Melt-Spun Multifilament Yarns

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3824
Author(s):  
Evaldas Bolskis ◽  
Erika Adomavičiūtė ◽  
Egidijus Griškonis ◽  
Valdas Norvydas
Keyword(s):  
Optical Properties ◽  
Ethanolic Extract ◽  
Tensile Tests ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Melt Spun ◽  
Spun Yarns ◽  
Degree Of Crystallization ◽  
Multifilament Yarns ◽  
Antibacterial And Antifungal

A possible approach for providing new properties for textiles is the insertion of natural ingredients into the textile product during the process of its manufacture. Myrrh has long been used in medicine as an antibacterial and antifungal material. Polylactide (PLA) is a thermoplastic synthetic biopolymer obtained from renewable resources—and due its biodegradability, is also widely used in medicine. In this study, films and multifilament yarns from modified biodegradable PLA granules with ethanolic and aqueous myrrh extracts were developed and characterized. Optical microscopy was used to determine the surface morphology of PLA/myrrh multifilament yarns. Tensile tests, ultraviolet-visible (UV-vis), differential scanning calorimetry (DSC) were applied to determine, consequently, mechanical, optical properties and degree of crystallinity of PLA/myrrh films and multifilament yarns. The chemical composition of PLA/myrrh multifilament yarns was estimated by Fourier-transform infrared (FTIR) spectroscopy method. The results showed that it is possible to form PLA melt-spun multifilament yarns with myrrh extract. The type of myrrh extract (ethanolic or aqueous) has a significant influence on the mechanical and optical properties of the PLA films and melt-spun yarns. The mechanical properties of PLA films and melt-spun multifilament yarns formed from PLA granules with aqueous myrrh extract decreased 19% and 21% more than PLA with ethanolic extract, respectively. Analysis of UV-vis spectra showed that, due to the yellow hue, the reflectance of PLA films and melt-spun PLA multifilament yarns modified with myrrh extracts decreased exponentially. The DSC test showed that multifilament yarns from PLA modified with aqueous extract had the highest degree of crystallization.

Thermal and Mechanical Characterization of Jute-Biopol Nanophased Green Composites

2011 ◽  
Vol 1312 ◽  
Author(s):  
Mohammad K Hossain ◽  
Mohammad W Dewan ◽  
Mahesh Hosur ◽  
Shaik Jeelani
Keyword(s):  
Thermal Performance ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Jute Fiber ◽  
Degree Of Crystallinity ◽  
Fiber Reinforced ◽  
Molding Process ◽  
Scanning Calorimetry ◽  
Solution Intercalation ◽  
Jute Fibers

ABSTRACTSurface modification of jute fibers was accomplished by performing chemical treatments including detergent washing, dewaxing, alkali, and acetic acid treatment. Morphology of modified surfaces examined using scanning electron microscopy (SEM) revealed improved surfaces for better adhesion with matrix. Better thermal performance of treated fibers was found from thermogravimetric analysis (TGA). Enhanced tensile properties of treated fibers were obtained from tensile tests. Using solution intercalation technique and magnetic stirring, 2%, 3%, and 4% by weight Montmorillonite K10 nanoclay were dispersed into a biodegradable polymer, Biopol. Thermal performance of nanoclay infused Biopol characterized using dynamic scanning calorimetry (DSC) showed improved degree of crystallinity by 7%. Jute fiber reinforced Biopol biocomposites with and without nanoclay were manufactured using treated and untreated jute fibers by compression molding process. Thermal and mechanical responses of treated fiber reinforced Biopol composites (TJBC) without nanoclay evaluated using dynamic mechanical analysis (DMA) and flexure tests showed 9% and 12% increase in storage modulus and flexure strength, respectively, compared to untreated jute fiber reinforced composites (UTJBC). The respective values were 100% and 35% for 4% nanoclay infused TJBC compared to UTJBC without nanoclay.

scholarly journals Hybrid Composites of Polylactide with Basalt and Carbon Fibers and Their Thermal Treatment

Materials ◽  
2018 ◽  
Vol 12 (1) ◽  
pp. 95 ◽  
Author(s):  
Stanisław Kuciel ◽  
Paulina Romańska
Keyword(s):  
Water Absorption ◽  
Elevated Temperatures ◽  
Hybrid Composites ◽  
Tensile Tests ◽  
Equal Mass ◽  
Degree Of Crystallinity ◽  
Stress Concentrations ◽  
Scanning Calorimetry ◽  
Heat Treated ◽  
The Matrix

In this research, polylactide was hybrid-reinforced and heat-treated in order to obtain durable structural materials with the use of eco-friendly components. Differential scanning calorimetry (DSC) analysis, tensile tests at various temperatures, Vicat tests, impact tests, and microscopic observations were conducted on the annealed and non-heat-treated specimens. The theoretical and true density, as well as water absorption, were also determined. The simultaneous introduction of chopped carbon and basalt fibers in equal mass fractions of 7.5% and 12.5% resulted in satisfactory increases in stiffness and tensile strength. The reinforcing effect was more efficient for the heat-treated composites, especially at elevated temperatures. Heat treatment significantly increased the degree of crystallinity of the matrix, improving heat resistance and reducing water absorption. It also reduced the stress concentrations in the injection-molded specimens.

scholarly journals Application of Melt-Blown Poly(lactic acid) Fibres in Self-Reinforced Composites

Polymers ◽  
2018 ◽  
Vol 10 (7) ◽  
pp. 766 ◽  
Author(s):  
Dániel Vadas ◽  
Dávid Kmetykó ◽  
György Marosi ◽  
Katalin Bocz
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Fold Increase ◽  
Tensile Tests ◽  
Degree Of Crystallinity ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Static Tensile ◽  
Micrometer Size ◽  
Nonwoven Mats

The aim of our research was to produce poly(lactic acid) (PLA) fibres with diameters in the micrometer size range, serving as the reinforcing phase in self-reinforced (SR) PLA composites. Nonwoven PLA mats were manufactured by solvent-free melt-blowing technology. Three types of PLA differing in d-lactide content were processed with a productivity as high as 36 g/h. The crystallinity of the PLA microfibres was enhanced by thermal annealing. A 2–3-fold increase in the degree of crystallinity was obtained, as measured by differential scanning calorimetry (DSC). Fibre diameters between 2–14 µm were revealed by scanning electron microscopy (SEM). Static tensile tests were performed on the nonwoven mats, showing the reduced moduli of the annealed fibres due the amorphous relaxation. The PLA mats were processed via the hot compaction technique and formed into SR–PLA composites. The morphological and mechanical properties of the obtained microstructural composites were comprehensively studied. Composites prepared from annealed, thermally more stable PLA nonwoven mats showed superior mechanical properties; the tensile strength improved by 47% due to the higher residual fibre content.

Localized Die Metallization Damage Induced During Laser-Marking of a Semiconductor Package

2007 ◽  
Author(s):  
Paul Eric B. Parañal
Keyword(s):  
Laser Beam ◽  
Direct Interaction ◽  
Silica Spheres ◽  
Layer By Layer ◽  
Laser Marking ◽  
Molding Compound ◽  
Molding Material ◽  
Die Surface ◽  
Passivation Layers ◽  
Propagation Medium

Abstract This paper presents a new fail mechanism for laser-marking induced die damage. Discovered during package qualification, silica spheres – commonly used as fillers in the molding material, was shown to act as a propagation medium that promote the direct interaction of the scribing laser beam and the die surface. Critical to the understanding of the fail mechanism is the deprocessing technique devised to allow layer by layer examination of the metallization and passivation layers in an encapsulated silicon die. The technique also made possible the inspection of the molding compound profile directly on top of the affected die area.

scholarly journals PEG-POSS Star Molecules Blended in Polyurethane with Flexible Hard Segments: Morphology and Dynamics

Molecules ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 99
Author(s):  
Konstantinos N. Raftopoulos ◽  
Edyta Hebda ◽  
Anna Grzybowska ◽  
Panagiotis A. Klonos ◽  
Apostolos Kyritsis ◽  
...  
Keyword(s):  
Glass Transition ◽  
Star Polymer ◽  
Polymerization Process ◽  
Degree Of Crystallinity ◽  
Dielectric Relaxation Spectroscopy ◽  
Scanning Calorimetry ◽  
Similar System ◽  
Soft Phase ◽  
Hard Segments ◽  
Star Molecules

A star polymer with a polyhedral oligomeric silsesquioxanne (POSS) core and poly(ethylene glycol) (PEG) vertex groups is incorporated in a polyurethane with flexible hard segments in-situ during the polymerization process. The blends are studied in terms of morphology, molecular dynamics, and charge mobility. The methods utilized for this purpose are scanning electron and atomic force microscopies (SEM, AFM), X-ray diffraction (XRD), differential scanning calorimetry (DSC), and to a larger extent dielectric relaxation spectroscopy (DRS). It is found that POSS reduces the degree of crystallinity of the hard segments. Contrary to what was observed in a similar system with POSS pendent along the main chain, soft phase calorimetric glass transition temperature drops as a result of plasticization, and homogenization of the soft phase by the star molecules. The dynamic glass transition though, remains practically unaffected, and a hypothesis is formed to resolve the discrepancy, based on the assumption of different thermal and dielectric responses of slow and fast modes of the system. A relaxation α′, slower than the bulky segmental α and common in polyurethanes, appears here too. A detailed analysis of dielectric spectra provides some evidence that this relaxation has cooperative character. An additional relaxation g, which is not commonly observed, accompanies the Maxwell Wagner Sillars interfacial polarization process, and has dynamics similar to it. POSS is found to introduce conductivity and possibly alter its mechanism. The study points out that different architectures of incorporation of POSS in polyurethane affect its physical properties by different mechanisms.

scholarly journals Wastes from Agricultural Silage Film Recycling Line as a Potential Polymer Materials

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1383
Author(s):  
Jerzy Korol ◽  
Aleksander Hejna ◽  
Klaudiusz Wypiór ◽  
Krzysztof Mijalski ◽  
Ewelina Chmielnicka
Keyword(s):  
Vinyl Acetate ◽  
Thermal Performance ◽  
Mechanical Performance ◽  
Ethylene Vinyl Acetate ◽  
Tensile Tests ◽  
Solid Particles ◽  
Polymer Materials ◽  
Slight Reduction ◽  
Scanning Calorimetry ◽  
Crystallinity Degree

The recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for potential methods for their utilization. In the presented work, we investigated the recycling potential of wastes originated from the agricultural films recycling line. Their structure and properties were analyzed, and they were modified with 2.5 wt % of commercially available compatibilizers. The mechanical and thermal performance of modified wastes were evaluated by tensile tests, thermogravimetric analysis, and differential scanning calorimetry. It was found that incorporation of such a small amount of modifiers may overcome the drawbacks caused by the presence of impurities. The incorporation of maleic anhydride-grafted compounds enhanced the tensile strength of wastes by 13–25%. The use of more ductile compatibilizers—ethylene-vinyl acetate and paraffin increased the elongation at break by 55–64%. The presence of compatibilizers also reduced the stiffness of materials resulting from the presence of solid particles. It was particularly emphasized for styrene-ethylene-butadiene-styrene and ethylene-vinyl acetate copolymers, which caused up to a 20% drop of Young’s modulus. Such effects may facilitate the further applications of analyzed wastes, e.g., in polymer film production. Thermal performance was only slightly affected by compatibilization. It caused a slight reduction in polyethylene melting temperatures (up to 2.8 °C) and crystallinity degree (up to 16%). For more contaminated materials, the addition of compatibilizers caused a minor reduction in the decomposition onset (up to 6 °C). At the same time, for the waste after three washing cycles, thermal stability was improved. Moreover, depending on the desired properties and application, materials do not have to go through the whole recycling line, simplifying the process, reducing energy and water consumption. The presented results indicate that it is possible to efficiently use the materials, which do not have to undergo the whole recycling process. Despite the presence of impurities, they could be applied in the manufacturing of products which do not require exceptional mechanical performance.

scholarly journals Characterization of Beeswax, Candelilla Wax and Paraffin Wax for Coating Cheeses

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 261
Author(s):  
Adolfo Bucio ◽  
Rosario Moreno-Tovar ◽  
Lauro Bucio ◽  
Jessica Espinosa-Dávila ◽  
Francisco Anguebes-Franceschi
Keyword(s):  
Physical And Mechanical Properties ◽  
Tensile Tests ◽  
Paraffin Wax ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Absorption Bands ◽  
Dimensional Changes ◽  
Ductile Behavior ◽  
Candelilla Wax

A study on the physical and mechanical properties of beeswax (BW), candelilla wax (CW), paraffin wax (PW) and blends was carried out with the aim to evaluate their usefulness as coatings for cheeses. Waxes were analyzed by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), differential scanning calorimetry (DSC), permeability, viscosity, flexural and tensile tests and scanning electron microscopy. Cheeses were coated with the waxes and stored for 5 weeks at 30 °C. Measured parameters were weight, moisture, occurrence and degree of fractures, and dimensional changes. The crystal phases identified by XRD for the three waxes allowed them to determine the length of alkanes and the nonlinear compounds in crystallizable forms in waxes. FTIR spectra showed absorption bands between 1800 and 800 cm−1 related to carbonyls in BW and CW. In DSC, the onset of melting temperature was 45.5 °C for BW, and >54 °C for CW and PW. Cheeses coated with BW did not show cracks after storage. Cheeses coated with CW and PW showed microcraks, and lost weight, moisture and shrunk. In the flexural and tensile tests, BW was ductile; CW and PW were brittle. BW blends with CW or PW displays a semi ductile behavior. Cheeses coated with BW blends lost less than 5% weight during storage. The best waxes were BW and the blends.

Sign in / Sign up

Export Citation Format

Share Document