scholarly journals Prediction of Earing of Cross-Rolled Al Sheets from {h00} Pole Figures

Metals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 192
Author(s):  
Marton Benke ◽  
Bence Schweitzer ◽  
Adrienn Hlavacs ◽  
Valeria Mertinger
Keyword(s):  
Deep Drawing ◽  
Plastic Anisotropy ◽  
Rolling Texture ◽  
X Ray Diffraction ◽  
Cross Rolling ◽  
X Ray ◽  
Aluminum Sheets ◽  
Pole Figures ◽  
Cold Rolling Texture ◽  
First Time

The plastic anisotropy of rolled Al sheets is the result of a crystallographic texture. It leads to the formation of uneven cup heights during deep-drawing, which is called earing. A new, simple and rapid method had been previously developed by the authors to predict earing directly from {h00} pole figures. In the present manuscript, this method is applied to cross-rolling for the first time. 5056 type aluminum sheets were unidirectionally- (conventionally) and cross-rolled from 4 to ~1 mm thickness in 6 or 12 passes. Earing was predicted from recalculated {200} pole figures obtained after X-ray diffraction texture measurements. The results were validated by deep-drawing tests. It is shown that the proposed method predicts the type (locations of ears) and magnitude of earing with satisfactory results. However, a different scaling factor must be used to calculate the magnitude of earing for cross-rolling than for unidirectional rolling even if all other parameters (including cold rolling, texture measurements, and deep-drawing) are the same. This is because the cross-rolled sheets exhibit a similar type but weaker earing compared to the unidirectionally rolled samples.

scholarly journals Study of the Preferred Orientation of Hydroxyapatite in Ivory from Zimbabwe and Mammoth Ivory from Siberia

Crystals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 572
Author(s):  
Xue Ying Sun ◽  
Ming Yue He ◽  
Jin Lin Wu
Keyword(s):  
Growth Direction ◽  
Preferred Orientation ◽  
Crystal Formation ◽  
Orientation Factor ◽  
X Ray Diffraction ◽  
X Ray ◽  
Angle Bisector ◽  
Pole Figures ◽  
First Time ◽  
Insight Into

In this paper, the pole figures plotted from X-ray diffraction data are employed to analyze the orientation of hydroxyapatite in ivory and mammoth ivory for the first time. The results present evidence of the lamellar structure and the hydroxyapatite appeared as tabular. A preferred orientation of hydroxyapatite was revealed in terms of the calculated orientation factor and the characteristics found in the pole figures. The c-axes of hydroxyapatite are mainly oriented along the growth direction. Both a-axes are on the left of the angle bisector of Retzius. Approximately 25–30° separates the a-axes and the angle bisector of Retzius in ivory, whereas the figure is approximately 10–15° in mammoth ivory. Our work is significant in providing more accurate knowledge of the shapes and organizational state of bio-mineral crystals and providing insight into crystal formation and development in bio-mineralization.

scholarly journals Quartz Crystallite Size and Moganite Content as Indicators of the Mineralogical Maturity of the Carboniferous Chert: The Case of Cherts from Eastern Asturias (Spain)

Minerals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 611
Author(s):  
Celia Marcos ◽  
María de Uribe-Zorita ◽  
Pedro Álvarez-Lloret ◽  
Alaa Adawy ◽  
Patricia Fernández ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Crystallite Size ◽  
Archaeological Sites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Infrared And Raman Spectroscopy ◽  
First Time ◽  
Geological Formations

Chert samples from different coastal and inland outcrops in the Eastern Asturias (Spain) were mineralogically investigated for the first time for archaeological purposes. X-ray diffraction, X-ray fluorescence, transmission electron microscopy, infrared and Raman spectroscopy and total organic carbon techniques were used. The low content of moganite, since its detection by X-ray diffraction is practically imperceptible, and the crystallite size (over 1000 Å) of the quartz in these cherts would be indicative of its maturity and could potentially be used for dating chert-tools recovered from archaeological sites. Also, this information can constitute essential data to differentiate the cherts and compare them with those used in archaeological tools. However, neither composition nor crystallite size would allow distinguishing between coastal and inland chert outcrops belonging to the same geological formations.

scholarly journals First Report on the Geologic Occurrence of Natural Na–A Zeolite and Associated Minerals in Cretaceous Mudstones of the Paja Formation of Vélez (Santander), Colombia

Crystals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Carlos Alberto Ríos-Reyes ◽  
German Alfonso Reyes-Mendoza ◽  
José Antonio Henao-Martínez ◽  
Craig Williams ◽  
Alan Dyer
Keyword(s):  
Natural Zeolite ◽  
Scanning Electron Micrographs ◽  
Total Sulfur ◽  
Zeolite A ◽  
X Ray Diffraction ◽  
X Ray ◽  
Mineral Phases ◽  
The World ◽  
Porosity And Permeability ◽  
First Time

This study reports for the first time the geologic occurrence of natural zeolite A and associated minerals in mudstones from the Cretaceous Paja Formation in the urban area of the municipality of Vélez (Santander), Colombia. These rocks are mainly composed of quartz, muscovite, pyrophyllite, kaolinite and chlorite group minerals, framboidal and cubic pyrite, as well as marcasite, with minor feldspar, sulphates, and phosphates. Total organic carbon (TOC), total sulfur (TS), and millimeter fragments of algae are high, whereas few centimeters and not biodiverse small ammonite fossils, and other allochemical components are subordinated. Na–A zeolite and associated mineral phases as sodalite occur just beside the interparticle micropores (honeycomb from framboidal, cube molds, and amorphous cavities). It is facilitated by petrophysical properties alterations, due to processes of high diagenesis, temperatures up to 80–100 °C, with weathering contributions, which increase the porosity and permeability, as well as the transmissivity (fluid flow), allowing the geochemistry remobilization and/or recrystallization of pre-existing silica, muscovite, kaolinite minerals group, salts, carbonates, oxides and peroxides. X-ray diffraction analyses reveal the mineral composition of the mudstones and scanning electron micrographs show the typical cubic morphology of Na–A zeolite of approximately 0.45 mμ in particle size. Our data show that the sequence of the transformation of phases is: Poorly crystalline aluminosilicate → sodalite → Na–A zeolite. A literature review shows that this is an unusual example of the occurrence of natural zeolites in sedimentary marine rocks recognized around the world.

scholarly journals The Effect of Surfactant-Modified Montmorillonite on the Cross-Linking Efficiency of Polysiloxanes

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2623
Author(s):  
Monika Wójcik-Bania ◽  
Jakub Matusik
Keyword(s):  
Total Pore Volume ◽  
Cross Linking ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
The Cross ◽  
Chain Lengths ◽  
First Time ◽  
Substituent Influence ◽  
Benzyl Substituent

Polymer–clay mineral composites are an important class of materials with various applications in the industry. Despite interesting properties of polysiloxanes, such matrices were rarely used in combination with clay minerals. Thus, for the first time, a systematic study was designed to investigate the cross-linking efficiency of polysiloxane networks in the presence of 2 wt % of organo-montmorillonite. Montmorillonite (Mt) was intercalated with six quaternary ammonium salts of the cation structure [(CH3)2R’NR]+, where R = C12, C14, C16, and R’ = methyl or benzyl substituent. The intercalation efficiency was examined by X-ray diffraction, CHN elemental analysis, and Fourier transform infrared (FTIR) spectroscopy. Textural studies have shown that the application of freezing in liquid nitrogen and freeze-drying after the intercalation increases the specific surface area and the total pore volume of organo-Mt. The polymer matrix was a poly(methylhydrosiloxane) cross-linked with two linear vinylsiloxanes of different siloxane chain lengths between end functional groups. X-ray diffraction and transmission electron microscopy studies have shown that the increase in d-spacing of organo-Mt and the benzyl substituent influence the degree of nanofillers’ exfoliation in the nanocomposites. The increase in the degree of organo-Mt exfoliation reduces the efficiency of hydrosilylation reaction monitored by FTIR. This was due to physical hindrance induced by exfoliated Mt particles.

scholarly journals A novel and potentially scalable CVD-based route towards SnO2:Mo thin films as transparent conducting oxides

2021 ◽  
Author(s):  
Tianlei Ma ◽  
Marek Nikiel ◽  
Andrew G. Thomas ◽  
Mohamed Missous ◽  
David J. Lewis
Keyword(s):  
Thin Films ◽  
Photoelectron Spectroscopy ◽  
Mixed Valence ◽  
Chemical Vapour ◽  
X Ray Diffraction ◽  
X Ray ◽  
Conducting Oxides ◽  
Valence States ◽  
3 Omega ◽  
First Time

AbstractIn this report, we prepared transparent and conducting undoped and molybdenum-doped tin oxide (Mo–SnO2) thin films by aerosol-assisted chemical vapour deposition (AACVD). The relationship between the precursor concentration in the feed and in the resulting films was studied by energy-dispersive X-ray spectroscopy, suggesting that the efficiency of doping is quantitative and that this method could potentially impart exquisite control over dopant levels. All SnO2 films were in tetragonal structure as confirmed by powder X-ray diffraction measurements. X-ray photoelectron spectroscopy characterisation indicated for the first time that Mo ions were in mixed valence states of Mo(VI) and Mo(V) on the surface. Incorporation of Mo6+ resulted in the lowest resistivity of $$7.3 \times 10^{{ - 3}} \Omega \,{\text{cm}}$$ 7.3 × 10 - 3 Ω cm , compared to pure SnO2 films with resistivities of $$4.3\left( 0 \right) \times 10^{{ - 2}} \Omega \,{\text{cm}}$$ 4.3 0 × 10 - 2 Ω cm . Meanwhile, a high transmittance of 83% in the visible light range was also acquired. This work presents a comprehensive investigation into impact of Mo doping on SnO2 films synthesised by AACVD for the first time and establishes the potential for scalable deposition of SnO2:Mo thin films in TCO manufacturing. Graphical abstract

scholarly journals Reactive Dual Magnetron Sputtering: A Fast Method for Preparing Stoichiometric Microcrystalline ZnWO4 Thin Films

Surfaces ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 106-114
Author(s):  
Yannick Hermans ◽  
Faraz Mehmood ◽  
Kerstin Lakus-Wollny ◽  
Jan P. Hofmann ◽  
Thomas Mayer ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Fast Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Substrates ◽  
Post Annealing ◽  
Rf Signal ◽  
First Time

Thin films of ZnWO4, a promising photocatalytic and scintillator material, were deposited for the first time using a reactive dual magnetron sputtering procedure. A ZnO target was operated using an RF signal, and a W target was operated using a DC signal. The power on the ZnO target was changed so that it would match the sputtering rate of the W target operated at 25 W. The effects of the process parameters were characterized using optical spectroscopy, X-ray diffraction, and scanning electron microscopy, including energy dispersive X-ray spectroscopy as well as X-ray photoelectron spectroscopy. It was found that stoichiometric microcrystalline ZnWO4 thin films could be obtained, by operating the ZnO target during the sputtering procedure at a power of 55 W and by post-annealing the resulting thin films for at least 10 h at 600 °C. As FTO coated glass substrates were used, annealing led as well to the incorporation of Na, resulting in n+ doped ZnWO4 thin films.

Crystalline and Electrical Properties of Ferroelectric Silver Niobate-tantalate thin Films

2000 ◽  
Vol 655 ◽  
Author(s):  
Jung-Hyuk Koh ◽  
S.I. Khartsev ◽  
Alex Grishin ◽  
Vladimir Petrovsky
Keyword(s):  
Temperature Stability ◽  
Frequency Dispersion ◽  
Processing Temperature ◽  
High Temperature Stability ◽  
X Ray Diffraction ◽  
Ferroelectric State ◽  
X Ray ◽  
Ferroelectric Hysteresis ◽  
First Time

AbstractFor the first time AgTa0.38Nb0.62O3 (ATN) films have been grown on the La0.7Sr0.3CoO3 (LSCO)/LaAlO3 single crystal as well as onto Pt80Ir20 (PtIr) polycrystalline substrate. Comprehensive X-ray diffraction analyses reveal epitaxial quality of ATN and LSCO films on the LaAlO3(001) substrate, while ATN/PtIr films have been found to be (001) preferentially oriented. Dielectric spectroscopy performed for ATN films and bulk ceramics in a wide temperature range 77 to 420 K shows the structural monoclinic M1-to-monoclinic M2 phase transition occurs in films at the temperature 60 °C lower than in ceramics. The tracing of the ferroelectric hysteresis P-E loops indicates the ferroelectric state in ATN films at temperatures below 125 K and yields remnant polarization of 0.4 μC/cm2 @ 77 K. Weak frequency dispersion, high temperature stability of dielectric properties as well as low processing temperature of 550 °C make ATN films to be attractive for various applications.

Synthesis and characterization of meso-to-meso directly linked porphyrin-diazaporphyrin triads

2018 ◽  
Vol 22 (09n10) ◽  
pp. 814-820
Author(s):  
Yingying Jia ◽  
Ling Xu ◽  
Bangshao Yin ◽  
Mingbo Zhou ◽  
Jianxin Song
Keyword(s):  
Nickel Complex ◽  
High Resolution Mass Spectrometry ◽  
Dihedral Angles ◽  
X Ray Diffraction ◽  
Extinction Coefficients ◽  
X Ray ◽  
H Nmr ◽  
First Time ◽  
Molar Extinction Coefficients

Beginning with 5,10,15-triarylporphyrin-nickel complex, five meso-to-meso directly linked porphyrin-diazaporphyrin triads were successfully prepared for the first time through a series of reactions including formylation via Vilsmeier–Haack reaction, condensation with pyrrole, bromination with [Formula: see text]-Bromosuccinimide (NBS), oxidation with 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ), metal-templated cyclization of dibromodipyrrin-metal complexes with NaN[Formula: see text] and demetalization. All these triads were comprehensively characterized by [Formula: see text]H NMR, high-resolution mass spectrometry and UV-vis absorption. In addition, the structure of compound 6Ni was unambiguously determined by X-ray diffraction analysis, which showed that the two dihedral angles are both 86.65 (4)[Formula: see text] between each mean plane of porphyrin and that of central diazaporphyrin The UV-vis absorption spectra disclosed that the longest wavelengths of Soret bands and Q bands for these triads were observed at 429 and 642 nm, respectively. In contrast to diazaporphyrin-porphyrin dyads, diazaporphyrin dimers and diazaporphyrin monomers reported previously the molar extinction coefficients, particularly for triad 8Ni are much higher.

Strain Measurement by X-ray Diffraction Methods

1949 ◽  
Vol 1 (3) ◽  
pp. 211-224
Author(s):  
G. B. Greenough
Keyword(s):  
Strain Measurement ◽  
Plastic Anisotropy ◽  
Stress And Strain ◽  
Routine Method ◽  
X Ray Diffraction ◽  
Strain Measurements ◽  
X Ray ◽  
The Past ◽  
Polycrystalline Metals ◽  
The Individual

SummaryMany papers have been written on the measurement of strain by X-ray diffraction methods and on the interpretation of these strains in terms of stresses. Whereas, during the past few years, the experimental methods of determining the strains have. remained largely unchanged, research has shown that the older techniques for calculating stresses from strains are not always valid.In this paper an attempt is made to describe some of the principles of strain measurement by X-ray diffraction methods to those who are unfamiliar with the methods. The types of stress and strain systems which may exist in polycrystalline metals are then considered, particular attention being paid to the effect of the elastic and plastic anisotropy of the individual crystals. Some indication is given as to how the earlier methods of interpreting X-ray strain measurements should be modified, but no rigid routine method is proposed for use in a general case.

Textures Applied to Mechanical Processing Technology Assessment in Ancient Bronze

2005 ◽  
Vol 495-497 ◽  
pp. 719-724
Author(s):  
R.E. Bolmaro ◽  
B. Molinas ◽  
E. Sentimenti ◽  
A.L. Fourty
Keyword(s):  
Orientation Distribution ◽  
Distribution Functions ◽  
Archaeological Sites ◽  
Mechanical Processing ◽  
Post Processing ◽  
X Ray Diffraction ◽  
Mechanical Process ◽  
X Ray ◽  
Pole Figures ◽  
Microscopic Inspection

Some ancient metallic art craft, utensils, silverware and weapons are externally undistinguishable from modern ones. Not only the general aspect and shape but also some uses have not changed through the ages. Moreover, when just some small pieces can be recovered from archaeological sites, the samples can not easily be ascribed to any known use and consequently identified. It is clear that mechanical processing has changed along history but frequently only a "microscopic" inspection can distinguish among different techniques. Some bronze samples have been collected from the Quarto d’Altino (Veneto) archaeological area in Italy (paleovenetian culture) and some model samples have been prepared by a modern artisan. The sample textures have been measured by X-ray Diffraction techniques. (111), (200) and (220) pole figures were used to calculate Orientation Distribution Functions and further recalculate pole figures and inverse pole figures. The results were compared with modern forging technology results. Textures are able to discern between hammering ancient techniques for sheet production and modern industrial rolling procedures. However, as it is demonstrated in the present work, forgery becomes difficult to detect if the goldsmith, properly warned, proceeds to erase the texture history with some hammering post-processing. The results of this contribution can offer to the archaeologists the opportunity to take into consideration the texture techniques in order to discuss the origin (culture) of the pieces and the characteristic mechanical process developed by the ancient artisan. Texture can also help the experts when discussing the originality of a certain piece keeping however in mind the cautions indicated in this publication.

Sign in / Sign up

Export Citation Format

Share Document