scholarly journals Nano-Bainitic Steels: Acceleration of Transformation by High Aluminum Addition and Its Effect on Their Mechanical Properties

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1210
Author(s):  
Mohamad Akram ◽  
Mohamed Soliman ◽  
Heinz Palkowski
Keyword(s):  
Low Cost ◽  
Impact Testing ◽  
Austenite Grain Size ◽  
Austenite Stability ◽  
Bainitic Steels ◽  
Transmission Electron ◽  
Transformation Time ◽  
Physical Simulations ◽  
Al Additions ◽  
Austempering Temperature

Additions of 3 and 5 wt.% Al have been investigated as a low-cost method for transformation acceleration in nano-bainitic steels. For both Al contents, two groups of steels with C-content in the range ~0.7 to ~0.95 wt.% were studied. Thermodynamic and physical simulations were used in alloy and heat treatment design. Characterization was performed via dilatometry, scanning and transmission electron microscopy, Synchrotron X-ray diffraction, and tensile and impact testing. Fast bainitic-transformation time-intervals ranging from 750–4600 s were recorded and tensile strengths up to 2000 MPa at a ductility of ~10 elongation percent were attainable for the 3 wt.% Al group at an austempering temperature of 265 °C. Higher Al additions were found to perform better than their lower Al counterparts as the austempering temperature is dropped. However, Al lowered the austenite stability, increased the martensite start temperature, austenitization temperatures and, consequently, the prior austenite grain size, as well as limiting the austempering temperatures to higher ones. Additionally, the lowered austenite stability coupled with higher additions of hardenability elements (here carbon) to maintain the martensite start at around 300 °C, causing the 5 wt.% Al group to have a large amount of low stability retained austenite (and consequently brittle martensite) in their microstructure, leading to a low elongation of around 5%.

Transmission Electron Microscopy of oriented Co84Cr14Ta2 thin films for longitudinal magnetic recording

1991 ◽  
Vol 49 ◽  
pp. 756-757
Author(s):  
T. P. Nolan
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Low Cost ◽  
Low Noise ◽  
Information Storage ◽  
High Coercivity ◽  
Magnetic Alloy ◽  
Magnetic Media ◽  
Transmission Electron

Thin film magnetic media are being used as low cost, high density forms of information storage. The development of this technology requires the study, at the sub-micron level, of morphological, crystallographic, and magnetic properties, throughout the depth of the deposited films. As the microstructure becomes increasingly fine, widi grain sizes approaching 100Å, the unique characterization capabilities of transmission electron microscopy (TEM) have become indispensable to the analysis of such thin film magnetic media.Films were deposited at 225°C, on two NiP plated Al substrates, one polished, and one circumferentially textured with a mean roughness of 55Å. Three layers, a 750Å chromium underlayer, a 600Å layer of magnetic alloy of composition Co84Cr14Ta2, and a 300Å amorphous carbon overcoat were then sputter deposited using a dc magnetron system at a power of 1kW, in a chamber evacuated below 10-6 torr and filled to 12μm Ar pressure. The textured medium is presently used in industry owing to its high coercivity, Hc, and relatively low noise. One important feature is that the coercivity in the circumferential read/write direction is significandy higher than that in the radial direction.

Influence of MBE Growth Conditions on Dislocation Densities of GaAs/Ge Epilayers Grown on Silicon Substrates

1985 ◽  
Vol 43 ◽  
pp. 364-365
Author(s):  
K.M. Hones ◽  
P. Sheldon ◽  
B.G. Yacobi ◽  
A. Mason
Keyword(s):  
High Efficiency ◽  
Lattice Mismatch ◽  
Low Cost ◽  
Growth Conditions ◽  
Nonradiative Recombination ◽  
Device Structure ◽  
Si Substrates ◽  
Transmission Electron ◽  
Dislocation Densities ◽  
Dislocation Type

There is increasing interest in growing epitaxial GaAs on Si substrates. Such a device structure would allow low-cost substrates to be used for high-efficiency cascade- junction solar cells. However, high-defect densities may result from the large lattice mismatch (∼4%) between the GaAs epilayer and the silicon substrate. These defects can act as nonradiative recombination centers that can degrade the optical and electrical properties of the epitaxially grown GaAs. For this reason, it is important to optimize epilayer growth conditions in order to minimize resulting dislocation densities. The purpose of this paper is to provide an indication of the quality of the epitaxially grown GaAs layers by using transmission electron microscopy (TEM) to examine dislocation type and density as a function of various growth conditions. In this study an intermediate Ge layer was used to avoid nucleation difficulties observed for GaAs growth directly on Si substrates. GaAs/Ge epilayers were grown by molecular beam epitaxy (MBE) on Si substrates in a manner similar to that described previously.

To Eliminate Curtain Effect of FIB TEM Samples by a Combination of Sample Dicing and Backside Milling

2014 ◽  
Author(s):  
Jian-Shing Luo ◽  
Hsiu Ting Lee
Keyword(s):  
Sample Preparation ◽  
Focused Ion Beam ◽  
Preparation Method ◽  
Low Cost ◽  
Ion Beam ◽  
Sample Preparation Method ◽  
Site Specific ◽  
Dual Beam ◽  
Transmission Electron

Abstract Several methods are used to invert samples 180 deg in a dual beam focused ion beam (FIB) system for backside milling by a specific in-situ lift out system or stages. However, most of those methods occupied too much time on FIB systems or requires a specific in-situ lift out system. This paper provides a novel transmission electron microscopy (TEM) sample preparation method to eliminate the curtain effect completely by a combination of backside milling and sample dicing with low cost and less FIB time. The procedures of the TEM pre-thinned sample preparation method using a combination of sample dicing and backside milling are described step by step. From the analysis results, the method has applied successfully to eliminate the curtain effect of dual beam FIB TEM samples for both random and site specific addresses.

scholarly journals Towards Iron-Titanium Oxide Nanostructures from Ecuadorian Black Mineral Sands

Minerals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 122
Author(s):  
Karina J. Lagos ◽  
Bojan A. Marinkovic ◽  
Alexis Debut ◽  
Karla Vizuete ◽  
Víctor H. Guerrero ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Titanium Oxide ◽  
Low Cost ◽  
Mineral Resources ◽  
Added Value ◽  
Secondary Phases ◽  
Hydrothermal Route ◽  
Oxide Nanostructures ◽  
Transmission Electron ◽  
Pre Treatment

Ecuadorian black mineral sands were used as starting material for the production of iron-titanium oxide nanostructures. For this purpose, two types of mineral processing were carried out, one incorporating a pre-treatment before conducting an alkaline hydrothermal synthesis (NaOH 10 M at 180 °C for 72 h), and the other prescinding this first step. Nanosheet-assembled flowers and nanoparticle agglomerates were obtained from the procedure including the pre-treatment. Conversely, nanobelts and plate-like particles were prepared by the single hydrothermal route. The nanoscale features of the product morphologies were observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analyses. The ilmenite and hematite molar fractions, within the ilmenite-hematite solid solution, in the as-synthetized samples were estimated by Brown’s approach using the computed values of unit-cell volumes from Le Bail adjustments of X-ray powder diffraction (XRPD) patterns. The resulting materials were mainly composed of Fe-rich ilmenite-hematite solid solutions (hematite molar contents ≥0.6). Secondary phases, which possibly belong to lepidocrocite-like or corrugated titanate structures, were also identified. The current study demonstrated the feasibility of employing Ecuadorian mineral resources as low-cost precursors to synthesize high-added-value nanostructures with promising applications in several fields.

scholarly journals Solvothermal Synthesis of Mn3O4Nanoparticle/Graphene Sheet Composites and Their Supercapacitive Properties

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Y. F. Liu ◽  
G. H. Yuan ◽  
Z. H. Jiang ◽  
Z. P. Yao
Keyword(s):  
Electron Microscopy ◽  
Graphene Sheet ◽  
Low Cost ◽  
High Specific Capacitance ◽  
Ethanol Solution ◽  
Diffraction Field ◽  
Electrochemical Performances ◽  
One Pot ◽  
Long Term Stability ◽  
Transmission Electron

Mn3O4nanoparticle/graphene sheet (GM) composites were synthesized via a one-pot and low-cost solvothermal process in an ethanol solution. The as-prepared materials were characterized by X-ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. Results showed that the nanosized Mn3O4particles had tetragonal hausmannite structure and were successfully loaded on the graphene sheets. Moreover, the electrochemical performances of GM composites produced by different mass percents of Mn2+/graphite oxide (GO) were evaluated by means of cyclic voltammetry and galvanostatic charge-discharge studies. The composite prepared with Mn2+/GO mass percent of 10 : 90 showed a high specific capacitance of 245 F/g at 5 mV/s in the 6 M KOH solution and better long-term stability along with 81% of its initial capacitance after 1200 cycles at 0.5 A/g.

scholarly journals Green Synthesis of Silver and Gold Nanoparticles via Sargassum serratifolium Extract for Catalytic Reduction of Organic Dyes

Catalysts ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 347
Author(s):  
Beomjin Kim ◽  
Woo Chang Song ◽  
Sun Young Park ◽  
Geuntae Park
Keyword(s):  
Gold Nanoparticles ◽  
Green Synthesis ◽  
Catalytic Reduction ◽  
Organic Dyes ◽  
Low Cost ◽  
Inorganic Nanoparticles ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Sargassum Serratifolium

The green synthesis of inorganic nanoparticles (NPs) using bio-materials has attained enormous attention in recent years due to its simple, eco-friendly, low-cost and non-toxic nature. In this work, silver nanoparticles (AgNPs) and gold nanoparticles (AuNPs) were synthesized by the marine algae extract, Sargassum serratifolium (SS). The characteristic studies of bio-synthesized SS-AgNPs and SS-AuNPs were carried out by using ultraviolet–visible (UV–Vis) absorption spectroscopy, dynamic light scattering (DLS), high-resolution transmission electron microscope (HR-TEM), selected area electron diffraction (SAED), energy-dispersive X-ray spectroscopy (EDX), X-ray powder diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). Phytochemicals in the algae extract, such as meroterpenoids, acted as a capping agent for the NPs’ growth. The synthesized Ag and Au NPs were found to have important catalytic activity for the degradation of organic dyes, including methylene blue, rhodamine B and methyl orange. The reduction of dyes by SS-AgNPs and -AuNPs followed the pseudo-first order kinetics.

Low-cost thermo-chemical process of TiO2 powder purification: Study of iterative gettering effect

2021 ◽  
Author(s):  
Nesrine Jaouabi ◽  
Wala Medfai ◽  
Marouan Khalifa ◽  
Rabia Zaghouani ◽  
Hatem Ezzaouia
Keyword(s):  
Porous Layer ◽  
Sacrificial Layer ◽  
Low Cost ◽  
Nir Spectroscopy ◽  
Tio2 Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Density Reduction ◽  
Transmission Electron ◽  
Layer Effect

The titanium dioxide (TiO2) purity is very important for the TiO2-based applications making essential the impurities density reduction. In this study, we propose an efficient purification process of TiO2 powder in order to reduce impurities. The low-cost proposed approach is based on an iterative gettering (IG) process combining three main steps: (1) a porous TiO2 sacrificial layer formation (p-TiO2), (2) a rapid thermal annealing (RTA) of p-TiO2 powder in an infrared oven at 950°C under air permitting the residual impurities diffusion to the porous layer surface and (3) etching in acid solution to remove the porous layer. Effect of the proposed gettering process on purification efficiency was evaluated by different characterization techniques such as the transmission electron microscopy (TEM), the energy dispersive x-ray spectroscopy (EDX), the UV–Visible-NIR spectroscopy, the X-ray diffraction (XRD) and atomic absorption spectroscopy (AAS). The obtained results showed the efficient removal of metal impurities, such as Cu, Al, P, and Fe confirming the efficiency of the process improving the purity from 89% to 99.96%.

Nickel Nanoparticles Supported on Diphenylphosphinated Poly(Vinyl Alcohol-Co-ethylene) as a New Heterogeneous and Recyclable Catalyst for Mizoroki–Heck Reactions

2017 ◽  
Vol 41 (9) ◽  
pp. 541-546 ◽  
Author(s):  
Farzaneh Ebrahimzadeh
Keyword(s):  
Vinyl Alcohol ◽  
Nickel Nanoparticles ◽  
Supported Catalysts ◽  
Low Cost ◽  
Poly Vinyl Alcohol ◽  
X Ray Diffraction ◽  
Heck Reactions ◽  
Modified Polymer ◽  
Transmission Electron ◽  
High Metal

Nickel nanoparticles (NiNPs) supported on diphenylphosphinated poly(vinyl alcohol- co-ethylene) (DPP-PVA- co-PE) were synthesised by first reacting poly(vinyl alcohol- co-ethylene) with chlorodiphenylphosphine (ClPPh2) under basic conditions and then treating the product with Ni(OAc)2 followed by reduction with NaBH4. (DPP-PVA- co-PE)-NiNPs, a new metallised polymer, was then shown to efficiently catalyse Mizoroki–Heck reactions of aryl iodides, bromides or activated chlorides with olefins such as styrene and n-butyl acrylate in dimethylformamide. In contrast with other polymer-supported catalysts, the main advantage of this method is the low cost of the catalyst due to the simple synthetic route using easily obtained materials and good recoverability. Transmission electron microscopy and X-ray diffraction measurements were used to show the high metal dispersion and small sizes of Ni nanoparticle on the surface of the modified polymer. DPP-PVA- co-PE-NiNPs could be recycled several times.

Heteroepitaxy of Ge on Cube-Textured Ni(001) Foils Through CaF2 Buffer Layer

MRS Advances ◽  
2016 ◽  
Vol 1 (43) ◽  
pp. 2947-2952
Author(s):  
L. Chen ◽  
Z.-H. Lu ◽  
T.-M. Lu ◽  
I. Bhat ◽  
S.B. Zhang ◽  
...  
Keyword(s):  
Buffer Layer ◽  
High Efficiency ◽  
Electron Backscatter Diffraction ◽  
Low Cost ◽  
High Quality ◽  
Tem Analysis ◽  
Transmission Electron ◽  
Electron Backscatter ◽  
Image Position ◽  
Backscatter Diffraction

ABSTRACTEpitaxial Ge films are useful as a substrate for high-efficiency solar cell applications. It is possible to grow epitaxial Ge films on low cost, cube textured Ni(001) sheets using CaF2(001) as a buffer layer. Transmission electron microscopy (TEM) analysis indicates that the CaF2(001) lattice has a 45o in-plane rotation relative to the Ni(001) lattice. The in-plane epitaxy relationships are CaF2[110]//Ni[100] and CaF2[$\bar 1$10]//Ni[010]. Energy dispersive spectroscopy (EDS) shows a sharp interface between Ge/CaF2 as well as between CaF2/Ni. Electron backscatter diffraction (EBSD) shows that the Ge(001) film has a large grain size (∼50 μm) with small angle grain boundaries (< 8o). The epitaxial Ge thin film has the potential to be used as a substrate to grow high quality III-V and II-VI semiconductors for optoelectronic applications.

Microstructure and Creep Properties of Selected Gravity Casting Magnesium Alloys

2016 ◽  
Vol 682 ◽  
pp. 372-379
Author(s):  
Tomasz Rzychoń
Keyword(s):  
Magnesium Alloys ◽  
Creep Resistance ◽  
Low Cost ◽  
Xrd Analysis ◽  
Phase Identification ◽  
Creep Tests ◽  
Gravity Casting ◽  
Creep Properties ◽  
Transmission Electron ◽  
Primary Crystals

In this paper microstructure and creep properties of Mg-Al-Ca-Sr, Mg-Zn-RE-Zr and Mg-Sn-Si gravity casting magnesium alloys are presented. The microstructure was characterized using light microscopy, scanning and transmission electron microscopy. Phase identification was made by SAED and XRD analysis. Creep tests were carried out in the temperature range from 180°C to 200°C at applied stress of 60 MPa. Microstructure of Mg-Al-Ca-Sr alloys composed of α-Mg grains and C36, C15 and C14 intermetallic compounds in the interdendritic regions. In case of Mg-Zn-RE-Zr alloys the dominant intermetallic compound is (Mg,Zn)12RE phase also located in the interdendritic regions. Microstructure of Mg-Sn-Si alloys after T6 heat treatment consists of plate-like precipitates of Mg2Sn phase, primary crystals of Mg2Si phase and globular Mg2Si phase. Among the alloys in this study, the low-cost Mg-5Al-3Ca-0.7Sr alloy has the best creep resistance. The other alloys, excluding the Mg-5Si-7Sn alloy, are characterized by a poorer creep resistance in compared to Mg-5Al-3Ca-0.7Sr alloy, however their creep resistance is better if compared to typical Mg-Al alloys. Creep resistance of Mg-5Si-7Sn alloy is very low.

Sign in / Sign up

Export Citation Format

Share Document