scholarly journals A 5-nV/√Hz Chopper Negative-R Stabilization Preamplifier for Audio Applications

Micromachines ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 478
Author(s):  
Jamel Nebhen ◽  
Khaled Alnowaiser ◽  
Stephane Meillere
Keyword(s):  
Supply Voltage ◽  
Signal To Noise Ratio ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Chopper Stabilization ◽  
Main Amplifier ◽  
Measurement Results ◽  
Low Noise Preamplifier

This paper presents a low-noise and low-power audio preamplifier. The proposed low-noise preamplifier employs a delay-time chopper stabilization (CHS) technique and a negative-R circuit, both in the auxiliary amplifier to cancel the non-idealities of the main amplifier. The proposed technique makes it possible to mitigate the preamplifier 1/f noise and thermal noise and improve its linearity. The low-noise preamplifier is implemented in 65 nm complementary metal-oxide semiconductor (CMOS) technology. The supply voltage is 1.2 V, while the power consumption is 159 µW, and the core area is 192 µm2. The proposed circuit of the preamplifier was fabricated and measured. From the measurement results over a signal bandwidth of 20 kHz, it achieves a signal-to-noise ratio (SNR) of 80 dB, an equivalent-input referred noise of 5 nV/√Hz and a noise efficiency factor (NEF) of 1.9 within the frequency range from 1 Hz to 20 kHz.

scholarly journals A Novel High Linearity and Low Power Folded CMOS LNA for UWB Receivers

2017 ◽  
Vol 27 (03) ◽  
pp. 1850047
Author(s):  
Xin Zhang ◽  
Chunhua Wang ◽  
Yichuang Sun ◽  
Haijun Peng
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Low Noise ◽  
Ultra Wideband ◽  
Oxide Semiconductor ◽  
High Linearity ◽  
Low Supply Voltage

This paper presents a high linearity and low power Low-Noise Amplifier (LNA) for Ultra-Wideband (UWB) receivers based on CHRT 0.18[Formula: see text][Formula: see text]m Complementary Metal-Oxide-Semiconductor (CMOS) technology. In this work, the folded topology is adopted in order to reduce the supply voltage and power consumption. Moreover, a band-pass LC filter is embedded in the folded-cascode circuit to extend bandwidth. The transconductance nonlinearity has a great impact on the whole LNA linearity performance under a low supply voltage. A post-distortion (PD) technique employing an auxiliary transistor is applied in the transconductance stage to improve the linearity. The post-layout simulation results indicate that the proposed LNA achieves a maximum power gain of 12.8[Formula: see text]dB. The input and output reflection coefficients both are lower than [Formula: see text][Formula: see text]dB over 2.5–11.5[Formula: see text]GHz. The input third-order intercept point (IIP3) is 5.6[Formula: see text]dBm at 8[Formula: see text]GHz and the noise figure (NF) is lower than 4.0[Formula: see text]dB. The LNA consumes 5.4[Formula: see text]mW power under a 1[Formula: see text]V supply voltage.

scholarly journals A Chopper Stabilization Audio Instrumentation Amplifier for IoT Applications

2020 ◽  
Vol 10 (2) ◽  
pp. 13 ◽  
Author(s):  
Jamel Nebhen ◽  
Pietro M. Ferreira ◽  
Sofiene Mansouri
Keyword(s):  
Power Consumption ◽  
Silicon Nanowires ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Instrumentation Amplifier ◽  
Chopper Stabilization ◽  
Iot Applications ◽  
Trade Offs

A low-noise instrumentation amplifier dedicated to a nano- and micro-electro-mechanical system (M&NEMS) microphone for the use in Internet of Things (IoT) applications is presented. The piezoresistive sensor and the electronic interface are respectively, silicon nanowires and an instrumentation amplifier. To design an instrumentation amplifier for IoT applications, different trade-offs are discussed like power consumption, gain, noise and sensitivity. Because the most critical noisy block is the amplifier, a delay-time chopper stabilization (CHS) technique is implemented around it to eliminate its offset and 1/f noise. The low-noise instrumentation amplifier is implemented in a 65-nm CMOS (Complementary metal–oxide–semiconductor) technology. The supply voltage is 2.5 V while the power consumption is 0.4 mW and the core area is 1 mm2. The circuit of the M&NEMS microphone and the amplifier was fabricated and measured. From measurement results over a signal bandwidth of 20 kHz, it achieves a signal-to-noise ratio (SNR) of 77 dB.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

A Study on Scalability and Variation of CMOS Low Noise Amplifier in Advance CMOS Technology Processes

2016 ◽  
Vol 833 ◽  
pp. 135-139
Author(s):  
Dayang Nur Salmi Dharmiza Awang Salleh ◽  
Rohana Sapawi
Keyword(s):  
Complementary Metal Oxide Semiconductor ◽  
Rf Circuits ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Oxide Semiconductor ◽  
Technology Scaling ◽  
Wireless Applications ◽  
Noise Amplifier ◽  
Technology Processes

Recent technology requires multistandard Radio Frequency (RF) chips for multipurpose wireless applications. In RF circuits, a low-noise amplifier (LNA) plays the key role in determining the receiver’s performance. With CMOS technology scaling, various designs has been adopted to study circuit’s characteristic and variation. In this paper, we present the results of scalable wideband LNA design based on complementary metal oxide semiconductor (CMOS), with its variance study. The design was fabricated in 180nm, 90nm, 65nm and 40nm CMOS technology.

scholarly journals DIGITAL CONTROLLED OSCILLATOR (DCO) FOR ALL DIGITAL PHASE-LOCKED LOOP (ADPLL) – A REVIEW

2019 ◽  
Vol 82 (1) ◽  
Author(s):  
Florence Choong ◽  
Mamun Ibne Reaz ◽  
Mohamad Ibrahim Kamaruzzaman ◽  
Md. Torikul Islam Badal ◽  
Araf Farayez ◽  
...  
Keyword(s):  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Phase Locked Loop ◽  
Cmos Technology ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Process Technology ◽  
Chip Area ◽  
Digital Phase ◽  
Low Power Dissipation

Digital controlled oscillator (DCO) is becoming an attractive replacement over the voltage control oscillator (VCO) with the advances of digital intensive research on all-digital phase locked-loop (ADPLL) in complementary metal-oxide semiconductor (CMOS) process technology. This paper presents a review of various CMOS DCO schemes implemented in ADPLL and relationship between the DCO parameters with ADPLL performance. The DCO architecture evaluated through its power consumption, speed, chip area, frequency range, supply voltage, portability and resolution. It can be concluded that even though there are various schemes of DCO that have been implemented for ADPLL, the selection of the DCO is frequently based on the ADPLL applications and the complexity of the scheme. The demand for the low power dissipation and high resolution DCO in CMOS technology shall remain a challenging and active area of research for years to come. Thus, this review shall work as a guideline for the researchers who wish to work on all digital PLL.

scholarly journals A 24.88 nV/√Hz Wheatstone Bridge Readout Integrated Circuit with Chopper-Stabilized Multipath Operational Amplifier

2020 ◽  
Vol 10 (1) ◽  
pp. 399 ◽  
Author(s):  
Kwonsang Han ◽  
Hyungseup Kim ◽  
Jaesung Kim ◽  
Donggeun You ◽  
Hyunwoo Heo ◽  
...  
Keyword(s):  
Integrated Circuit ◽  
Operational Amplifier ◽  
Wheatstone Bridge ◽  
Input Resistance ◽  
Cmos Technology ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Instrumentation Amplifier ◽  
Readout Integrated Circuit ◽  
Chopper Stabilization

This paper proposes a low noise readout integrated circuit (IC) with a chopper-stabilized multipath operational amplifier suitable for a Wheatstone bridge sensor. The input voltage of the readout IC changes due to a change in input resistance, and is efficiently amplified using a three-operational amplifier instrumentation amplifier (IA) structure with high input impedance and adjustable gain. Furthermore, a chopper-stabilized multipath structure is applied to the operational amplifier, and a ripple reduction loop (RRL) in the low frequency path (LFP) is employed to attenuate the ripple generated by the chopper stabilization technique. A 12-bit successive approximation register (SAR) analog-to-digital converter (ADC) is employed to convert the output voltage of the three-operational amplifier IA into digital code. The Wheatstone bridge readout IC is manufactured using a standard 0.18 µm complementary metal-oxide-semiconductor (CMOS) technology, drawing 833 µA current from a 1.8 V supply. The input range and the input referred noise are ±20 mV and 24.88 nV/√Hz, respectively.

A New Technique for Designing Low-Power High-Speed Domino Logic Circuits in FinFET Technology

2019 ◽  
Vol 28 (10) ◽  
pp. 1950165 ◽  
Author(s):  
Sandeep Garg ◽  
Tarun K. Gupta
Keyword(s):  
Low Power ◽  
High Speed ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Power Reduction ◽  
Maximum Power ◽  
Oxide Semiconductor ◽  
Domino Logic ◽  
Maximum Delay

In this paper, a fin field-effect transistor (FinFET)-based domino technique dynamic node-driven feedback transistor domino logic (DNDFTDL) is designed for low-power, high-speed and improved noise performance. In the proposed domino technique, the concept of current division is explored below the evaluation network for enhancement of performance parameters. Simulations are carried out for 32-nm complementary metal–oxide–semiconductor (CMOS) and FinFET node using HSPICE for 2-, 4-, 8- and 16-input OR gates with a DC supply voltage of 0.9[Formula: see text]V. Proposed technique shows a maximum power reduction of 73.93% in FinFET short-gate (SG) mode as compared to conditional stacked keeper domino logic (CSKDL) technique and a maximum power reduction of 72.12% as compared to modified high-speed clocked delay domino logic (M-HSCD) technique in FinFET low-power (LP) mode. The proposed technique shows a maximum delay reduction of 35.52% as compared to voltage comparison domino (VCD) technique in SG mode and a reduction of 25.01% as compared to current mirror footed domino logic (CMFD) technique in LP mode. The unity noise gain (UNG) of the proposed circuit is 1.72–[Formula: see text] higher compared to different existing techniques in FinFET SG mode and is 1.42–[Formula: see text] higher in FinFET LP mode. The Figure of Merit (FOM) of the proposed circuit is up to [Formula: see text] higher as compared to existing domino logic techniques because of lower values of power, delay and area and higher values of UNG of the proposed circuit. In addition, the proposed technique shows a maximum power reduction of up to 68.64% in FinFET technology as compared to its counterpart in CMOS technology.

A speed-optimized, low-noise APD with 0.18 μm CMOS technology for the VLC applications

2020 ◽  
Vol 34 (29) ◽  
pp. 2050321
Author(s):  
Wei Wang ◽  
Hong-An Zeng ◽  
Fang Wang ◽  
Guanyu Wang ◽  
Yingtao Xie ◽  
...  
Keyword(s):  
Dark Current ◽  
Complementary Metal Oxide Semiconductor ◽  
Visible Light Communication ◽  
Cmos Technology ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Excess Noise ◽  
Avalanche Breakdown ◽  
Cmos Process ◽  
Noise Characteristics

A new avalanche photodiode device applied to a visible light communication (VLC) system is designed using a standard 0.18 [Formula: see text]m complementary metal oxide semiconductor process. Compared to regular CMOS APD devices, the proposed device adds a [Formula: see text]-well layer above the deep [Formula: see text]-well/[Formula: see text]-substrate structure, and an [Formula: see text]/[Formula: see text] layer is deposited upon it. The [Formula: see text]/[Formula: see text] layer acts as an avalanche breakdown layer of the device, and an STI structure is used to prevent the edge break prematurely. The simulation results shows that the avalanche breakdown voltage is as low as 9.9 V, dark current is below [Formula: see text] A under −9.5 V bias voltage, and the 3 dB bandwidth is of 5.9 GHz. It is due to the use of the 0.18 [Formula: see text]m CMOS process-specific STI protection ring and short-circuits the connection of the deep [Formula: see text]-well/[Formula: see text]-substrate, and the dark current is reduced to be lower than two orders of magnitude compared to regular CMOS APD. Gain and noise characteristics are accurately calculated from Hayat dead-space model applied to this CMOS APD. So, this device’s gain and excess noise factor are 20 and 2.5, respectively.

Organic CMOS Technology Based on Interface Doped Pentacene

2005 ◽  
Vol 871 ◽  
Author(s):  
Marcus Ahles ◽  
Roland Schmechel ◽  
Heinz von Seggern
Keyword(s):  
Gate Voltage ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Cmos Inverter ◽  
Organic Systems ◽  
Electron Accumulation ◽  
P Type

AbstractAn organic complementary-metal-oxide-semiconductor (CMOS) inverter based on pentacene acting as both n- and p-type organic semiconductor is presented. The circuit consists of two spatially separated transistors which are realized within one continuous pentacene layer. Both transistors act exclusively in unipolar mode with electron and hole mobilities of 0.11 cm2V-1s-1 and 0.10 cm2V-1s-1, respectively. In the domain of the n-channel, electron accumulation in the pentacene is enabled by deposition of traces of calcium acting as electron donator. The CMOS inverter works reliably within the range of the supply voltage (60 V) with a gain in between 17 and 24 which is among the highest values observed in organic systems. Nevertheless, the circuit shows hysteresis, which is explained by a gate voltage depending trap occupation in the n-channel.

scholarly journals An Analogue Multiplier using CNTFET Technology

2020 ◽  
Vol 19 ◽  
Keyword(s):  
Analog Circuits ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor ◽  
Analog Multiplier ◽  
Effect Transistor ◽  
Four Quadrant ◽  
Better Than

The endeavor to overcome problems of complementary metal oxide semiconductor technology makes the advent of Carbon nanotube field effect transistor (CNTFET). Improvement of structure transistor CNTFET makes higher mobility and electrostatics of gate electrons. Therefore, many analog circuits are now designed based on CNTFET technology. This paper presents a low power current mode four-quadrant analog multiplier based on CNTFET and CMOS technologies. All simulations were done with the synopsys Hspice simulator using 32nm CNTFET model from Stanford University and 32nm CMOS from PTM library at a supply voltage of 3.3 v. It was shown that the simulation of a multiplier based on CNTFET technology performs better than a multiplier based on CMOS technology.

Sign in / Sign up

Export Citation Format

Share Document