scholarly journals A Chopper Stabilization Audio Instrumentation Amplifier for IoT Applications

2020 ◽  
Vol 10 (2) ◽  
pp. 13 ◽  
Author(s):  
Jamel Nebhen ◽  
Pietro M. Ferreira ◽  
Sofiene Mansouri
Keyword(s):  
Power Consumption ◽  
Silicon Nanowires ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Instrumentation Amplifier ◽  
Chopper Stabilization ◽  
Iot Applications ◽  
Trade Offs

A low-noise instrumentation amplifier dedicated to a nano- and micro-electro-mechanical system (M&NEMS) microphone for the use in Internet of Things (IoT) applications is presented. The piezoresistive sensor and the electronic interface are respectively, silicon nanowires and an instrumentation amplifier. To design an instrumentation amplifier for IoT applications, different trade-offs are discussed like power consumption, gain, noise and sensitivity. Because the most critical noisy block is the amplifier, a delay-time chopper stabilization (CHS) technique is implemented around it to eliminate its offset and 1/f noise. The low-noise instrumentation amplifier is implemented in a 65-nm CMOS (Complementary metal–oxide–semiconductor) technology. The supply voltage is 2.5 V while the power consumption is 0.4 mW and the core area is 1 mm2. The circuit of the M&NEMS microphone and the amplifier was fabricated and measured. From measurement results over a signal bandwidth of 20 kHz, it achieves a signal-to-noise ratio (SNR) of 77 dB.

scholarly journals A 5-nV/√Hz Chopper Negative-R Stabilization Preamplifier for Audio Applications

Micromachines ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 478
Author(s):  
Jamel Nebhen ◽  
Khaled Alnowaiser ◽  
Stephane Meillere
Keyword(s):  
Supply Voltage ◽  
Signal To Noise Ratio ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Chopper Stabilization ◽  
Main Amplifier ◽  
Measurement Results ◽  
Low Noise Preamplifier

This paper presents a low-noise and low-power audio preamplifier. The proposed low-noise preamplifier employs a delay-time chopper stabilization (CHS) technique and a negative-R circuit, both in the auxiliary amplifier to cancel the non-idealities of the main amplifier. The proposed technique makes it possible to mitigate the preamplifier 1/f noise and thermal noise and improve its linearity. The low-noise preamplifier is implemented in 65 nm complementary metal-oxide semiconductor (CMOS) technology. The supply voltage is 1.2 V, while the power consumption is 159 µW, and the core area is 192 µm2. The proposed circuit of the preamplifier was fabricated and measured. From the measurement results over a signal bandwidth of 20 kHz, it achieves a signal-to-noise ratio (SNR) of 80 dB, an equivalent-input referred noise of 5 nV/√Hz and a noise efficiency factor (NEF) of 1.9 within the frequency range from 1 Hz to 20 kHz.

scholarly journals A 24.88 nV/√Hz Wheatstone Bridge Readout Integrated Circuit with Chopper-Stabilized Multipath Operational Amplifier

2020 ◽  
Vol 10 (1) ◽  
pp. 399 ◽  
Author(s):  
Kwonsang Han ◽  
Hyungseup Kim ◽  
Jaesung Kim ◽  
Donggeun You ◽  
Hyunwoo Heo ◽  
...  
Keyword(s):  
Integrated Circuit ◽  
Operational Amplifier ◽  
Wheatstone Bridge ◽  
Input Resistance ◽  
Cmos Technology ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Instrumentation Amplifier ◽  
Readout Integrated Circuit ◽  
Chopper Stabilization

This paper proposes a low noise readout integrated circuit (IC) with a chopper-stabilized multipath operational amplifier suitable for a Wheatstone bridge sensor. The input voltage of the readout IC changes due to a change in input resistance, and is efficiently amplified using a three-operational amplifier instrumentation amplifier (IA) structure with high input impedance and adjustable gain. Furthermore, a chopper-stabilized multipath structure is applied to the operational amplifier, and a ripple reduction loop (RRL) in the low frequency path (LFP) is employed to attenuate the ripple generated by the chopper stabilization technique. A 12-bit successive approximation register (SAR) analog-to-digital converter (ADC) is employed to convert the output voltage of the three-operational amplifier IA into digital code. The Wheatstone bridge readout IC is manufactured using a standard 0.18 µm complementary metal-oxide-semiconductor (CMOS) technology, drawing 833 µA current from a 1.8 V supply. The input range and the input referred noise are ±20 mV and 24.88 nV/√Hz, respectively.

scholarly journals Fully Differential Chopper-Stabilized Multipath Current-Feedback Instrumentation Amplifier with R-2R DAC Offset Adjustment for Resistive Bridge Sensors

2019 ◽  
Vol 10 (1) ◽  
pp. 63 ◽  
Author(s):  
Yongsu Kwon ◽  
Hyungseup Kim ◽  
Jaesung Kim ◽  
Kwonsang Han ◽  
Donggeun You ◽  
...  
Keyword(s):  
Integrated Circuit ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Instrumentation Amplifier ◽  
Cmos Process ◽  
Current Feedback ◽  
Readout Integrated Circuit ◽  
Fully Differential ◽  
Chopper Stabilization ◽  
Rejection Ratio

A fully differential multipath current-feedback instrumentation amplifier (CFIA) for a resistive bridge sensor readout integrated circuit (IC) is proposed. To reduce the CFIA’s own offset and 1/f noise, a chopper stabilization technique is implemented. To attenuate the output ripple caused by chopper up-modulation, a ripple reduction loop (RRL) is employed. A multipath architecture is implemented to compensate for the notch in the chopping frequency band of the transfer function. To prevent performance degradation resulting from external offset, a 12-bit R-2R digital-to-analog converter (DAC) is employed. The proposed CFIA has an adjustable gain of 16–44 dB with 5-bit programmable resistors. The proposed resistive sensor readout IC is implemented in a 0.18 μm complementary metal-oxide-semiconductor (CMOS) process. The CFIA draws 169 μA currents from a 3.3 V supply. The simulated input-referred noise and noise efficiency factor (NEF) are 28.3 nV/√Hz and 14.2, respectively. The simulated common-mode rejection ratio (CMRR) is 162 dB, and the power supply rejection ratio (PSRR) is 112 dB.

scholarly journals A Novel High Linearity and Low Power Folded CMOS LNA for UWB Receivers

2017 ◽  
Vol 27 (03) ◽  
pp. 1850047
Author(s):  
Xin Zhang ◽  
Chunhua Wang ◽  
Yichuang Sun ◽  
Haijun Peng
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Low Noise ◽  
Ultra Wideband ◽  
Oxide Semiconductor ◽  
High Linearity ◽  
Low Supply Voltage

This paper presents a high linearity and low power Low-Noise Amplifier (LNA) for Ultra-Wideband (UWB) receivers based on CHRT 0.18[Formula: see text][Formula: see text]m Complementary Metal-Oxide-Semiconductor (CMOS) technology. In this work, the folded topology is adopted in order to reduce the supply voltage and power consumption. Moreover, a band-pass LC filter is embedded in the folded-cascode circuit to extend bandwidth. The transconductance nonlinearity has a great impact on the whole LNA linearity performance under a low supply voltage. A post-distortion (PD) technique employing an auxiliary transistor is applied in the transconductance stage to improve the linearity. The post-layout simulation results indicate that the proposed LNA achieves a maximum power gain of 12.8[Formula: see text]dB. The input and output reflection coefficients both are lower than [Formula: see text][Formula: see text]dB over 2.5–11.5[Formula: see text]GHz. The input third-order intercept point (IIP3) is 5.6[Formula: see text]dBm at 8[Formula: see text]GHz and the noise figure (NF) is lower than 4.0[Formula: see text]dB. The LNA consumes 5.4[Formula: see text]mW power under a 1[Formula: see text]V supply voltage.

A 10-bit 200 MS/s pipelined ADC with parallel sampling and switched op-amp sharing technique

Circuit World ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
D.S. Shylu Sam ◽  
P. Sam Paul
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Sampling Technique ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Pipelined Adc ◽  
Content Type ◽  
Op Amp ◽  
Op Amps ◽  
Parallel Sampling

Purpose In parallel sampling method, the size of the sampling capacitor is reduced to improve the bandwidth of the ADC. Design/methodology/approach Various low-power techniques for 10-bit 200MS/s pipelined analog-to-digital converter (ADC) are presented. This work comprises two techniques including parallel sampling and switched op-amp sharing technique. Findings This paper aims to study the effect of parallel sampling and switched op-amp sharing techniques on power consumption in pipelined ADC. In switched op-amp sharing technique, the numbers of op-amps used in the stages are reduced. Because of the reduction in the size of capacitors in parallel sampling technique and op-amps in the switched op-amp sharing technique, the power consumption of the proposed pipelined ADC is reduced to a greater extent. Originality/value Simulated the 10-bit 200MS/s pipelined ADC with complementary metal oxide semiconductor process and the simulation results shows a maximum differential non-linearity of +0.31/−0.31 LSB and the maximum integral non-linearity (of +0.74/−0.74 LSB with 62.9 dB SFDR, 55.90 dB SNDR and ENOB of 8.99 bits, respectively, for 18mW power consumption with the supply voltage of 1.8 V.

scholarly journals An E-Band 21-dB Variable-Gain Amplifier with 0.5-V Supply in 40-nm CMOS

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 804
Author(s):  
Gibeom Shin ◽  
Kyunghwan Kim ◽  
Kangseop Lee ◽  
Hyun-Hak Jeong ◽  
Ho-Jin Song
Keyword(s):  
Power Consumption ◽  
Frequency Band ◽  
Noise Figure ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Operating Frequency ◽  
Variable Gain Amplifier ◽  
Variable Gain ◽  
Operating Frequency Band ◽  
Shunt Capacitors

This paper presents a variable-gain amplifier (VGA) in the 68–78 GHz range. To reduce DC power consumption, the drain voltage was set to 0.5 V with competitive performance in the gain and the noise figure. High-Q shunt capacitors were employed at the gate terminal of the core transistors to move input matching points for easy matching with a compact transformer. The four stages amplifier fabricated in 40-nm bulk complementary metal oxide semiconductor (CMOS) showed a peak gain of 24.5 dB at 71.3 GHz and 3‑dB bandwidth of more than 10 GHz in 68–78 GHz range with approximately 4.8-mW power consumption per stage. Gate-bias control of the second stage in which feedback capacitances were neutralized with cross-coupled capacitors allowed us to vary the gain by around 21 dB in the operating frequency band. The noise figure was estimated to be better than 5.9 dB in the operating frequency band from the full electromagnetic (EM) simulation.

scholarly journals A High Efficiency Low Noise RF-to-DC Converter Employing Gm-Boosting Envelope Detector and Offset Canceled Latch Comparator

Electronics ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 1078
Author(s):  
Thi Thuy Pham ◽  
Dongmin Kim ◽  
Seo-Hyeong Jeong ◽  
Junghyup Lee ◽  
Donggu Im
Keyword(s):  
Power Consumption ◽  
High Efficiency ◽  
Supply Voltage ◽  
Current Source ◽  
Low Noise ◽  
The Body ◽  
Common Source ◽  
Conversion Gain ◽  
Input Transistor ◽  
Envelope Detector

This work presents a high efficiency RF-to-DC conversion circuit composed of an LC-CL balun-based Gm-boosting envelope detector, a low noise baseband amplifier, and an offset canceled latch comparator. It was designed to have high sensitivity with low power consumption for wake-up receiver (WuRx) applications. The proposed envelope detector is based on a fully integrated inductively degenerated common-source amplifier with a series gate inductor. The LC-CL balun circuit is merged with the core of the envelope detector by sharing the on-chip gate and source inductors. The proposed technique doubles the transconductance of the input transistor of the envelope detector without any extra power consumption because the gate and source voltage on the input transistor operates in a differential mode. This results in a higher RF-to-DC conversion gain. In order to improve the sensitivity of the wake-up radio, the DC offset of the latch comparator circuit is canceled by controlling the body bias voltage of a pair of differential input transistors through a binary-weighted current source cell. In addition, the hysteresis characteristic is implemented in order to avoid unstable operation by the large noise at the compared signal. The hysteresis window is programmable by changing the channel width of the latch transistor. The low noise baseband amplifier amplifies the output signal of the envelope detector and transfers it into the comparator circuit with low noise. For the 2.4 GHz WuRx, the proposed envelope detector with no external matching components shows the simulated conversion gain of about 16.79 V/V when the input power is around the sensitivity of −60 dBm, and this is 1.7 times higher than that of the conventional envelope detector with the same current and load. The proposed RF-to-DC conversion circuit (WuRx) achieves a sensitivity of about −65.4 dBm based on 45% to 55% duty, dissipating a power of 22 μW from a 1.2 V supply voltage.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

Review: Static and Dynamic Analysis Methods for Multi-Branch Biasing Circuits

2018 ◽  
Vol 27 (13) ◽  
pp. 1830008
Author(s):  
Jin Wu ◽  
Pengfei Dai ◽  
Jie Peng ◽  
Lixia Zheng ◽  
Weifeng Sun
Keyword(s):  
Feedback Loop ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Critical Parameters ◽  
Cmos Process ◽  
Stable Equilibrium Point ◽  
Static And Dynamic Analysis ◽  
Text Structures ◽  
Different Types

The fundamental theories and primary structures for the multi-branch self-biasing circuits are reviewed in this paper. First, the [Formula: see text]/[Formula: see text] and [Formula: see text]/[Formula: see text] structures illustrating the static current definition mechanism are presented, including the conditions of starting up and entering into a stable equilibrium point. Then, the AC method based on the loop gain evaluation is utilized to analyze different types of circuits. On this basis, the laws which can couple the branches of self-biasing circuits to construct a suitable close feedback loop are summarized. By adopting Taiwan Semiconductor Manufacturing Company (TSMC)’s 0.18[Formula: see text][Formula: see text]m complementary metal–oxide–semiconductor (CMOS) process with 1.8[Formula: see text][Formula: see text] supply voltage, nearly all the circuits mentioned in the paper are simulated in the same branch current condition, which is close to the corresponding calculated results. Therefore, the methods summarized in this paper can be utilized for distinguishing, constructing, and optimizing critical parameters for various structures of the self-biasing circuits.

A Study on Scalability and Variation of CMOS Low Noise Amplifier in Advance CMOS Technology Processes

2016 ◽  
Vol 833 ◽  
pp. 135-139
Author(s):  
Dayang Nur Salmi Dharmiza Awang Salleh ◽  
Rohana Sapawi
Keyword(s):  
Complementary Metal Oxide Semiconductor ◽  
Rf Circuits ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Oxide Semiconductor ◽  
Technology Scaling ◽  
Wireless Applications ◽  
Noise Amplifier ◽  
Technology Processes

Recent technology requires multistandard Radio Frequency (RF) chips for multipurpose wireless applications. In RF circuits, a low-noise amplifier (LNA) plays the key role in determining the receiver’s performance. With CMOS technology scaling, various designs has been adopted to study circuit’s characteristic and variation. In this paper, we present the results of scalable wideband LNA design based on complementary metal oxide semiconductor (CMOS), with its variance study. The design was fabricated in 180nm, 90nm, 65nm and 40nm CMOS technology.

Sign in / Sign up

Export Citation Format

Share Document