scholarly journals Reclaimed Polymers as Asphalt Binder Modifiers for More Sustainable Roads: A Review

2019 ◽  
Vol 11 (3) ◽  
pp. 646 ◽  
Author(s):  
Luzana Brasileiro ◽  
Fernando Moreno-Navarro ◽  
Raúl Tauste-Martínez ◽  
Jose Matos ◽  
Maria Rubio-Gámez
Keyword(s):  
Mechanical Performance ◽  
Asphalt Binder ◽  
Crumb Rubber ◽  
Economic Benefits ◽  
Asphalt Binders ◽  
Mixing Conditions ◽  
Ethyl Vinyl ◽  
General Terms ◽  
Comparative Review ◽  
Modified Binder

The use of polymer-modified binders in asphalt mixtures has become more widespread due to their reduced thermal susceptibility and improved rutting and fatigue resistance. Nevertheless, their high cost limits their application, thus making the use of reclaimed polymers (RP) an interesting alternative for both reducing price and extending the service life of pavements. This paper; therefore, presents a comparative review of the recycled polymers most commonly studied as bitumen modifiers: polyethylene (PE), polypropylene (PP), polyvinyl chloride (PVC), ethyl vinyl acetate (EVA), and ground tire rubber (GTR), in order to facilitate their selection and extend the use of the bitumen. The differences in terms of melting point, mixing conditions, and maximum quantity of added polymer are analyzed. Moreover, their effect on the mechanical behavior of the asphalt binders and their stability with and without the use of additives is presented. According to the literature revision, the performance of the new binder is more influenced by the kind of polymer that was incorporated and the mixing conditions than by the base bitumen that was chosen, although rheological evaluation is needed to fully understand the modification mechanisms of the modified binder. In general terms, plastomers have a stronger effect in terms of increasing the stiffness of the bitumen in comparison with crumb rubber (elastomers), thus providing an improved rutting resistance. The joint use of polyethylene (plastomer) and crumb rubber (elastomer) can be an interesting option for its recycling potential and mechanical performance, although further study is needed to achieve stable bitumen across the entire range of temperatures; additives, such as maleic anhydride (MA), are commonly employed to improve the stability of the binder and enhance its characteristics, but their use could limit the economic benefits of using recycled materials.

scholarly journals Experimental Study to Determine the Most Preferred Additive for Improving Asphalt Performance Using Polypropylene, Crumb Rubber, and Tafpack Super in Medium and High-Temperature Range

2019 ◽  
Vol 9 (8) ◽  
pp. 1567 ◽  
Author(s):  
Huang Xiaoming ◽  
Ismail Bakheit Eldouma
Keyword(s):  
High Temperature ◽  
Physical Properties ◽  
Mechanical Performance ◽  
Asphalt Binder ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Modified Bitumen ◽  
Asphalt Modification ◽  
Rotational Viscosity ◽  
Asphalt Performance

The overall objectives of this study were to determine the most appropriate additive for improving the physical properties and the medium- and high-temperature performances (mechanical performance) of asphalt binders. Three different types of modified binders were prepared: crumb rubber modifier (CRM), polypropylene (PP), and tafpack super (TPS), which had concentrations of 2%, 3%, 3.5%, and 4% by weight of asphalt binder, for each modifier. Their physical and rheological properties were evaluated by applying various tests such as ductility, rotational viscosity, toughness, and tenacity, as well as the dynamic shear rheometer (DSR) test. As a result, the physical properties of the modified bitumen binders were compared, as were the medium- and high-temperature performances (mechanical performance), which had temperatures of 58, 64, 70, 76, 82, and 88 °C, respectively. This was how the most appropriate modifier was determined. The results demonstrated that the asphalt binder properties significantly improved by utilizing CRM followed by PP and TPS modifiers. The increase in the rutting parameter (G*/sin(δ)) after asphalt modification indicated its excellent performance at both medium- and high-temperatures. Lastly, the CRM was determined as the most preferred additive because of its positive effect on the physical properties and enhancement of the medium- and high-temperature performance (mechanical performance).

scholarly journals Optical Characterization of Asphalt Binders Containing Wax Additives

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Mithil Mazumder ◽  
Raju Ahmed ◽  
Moon-Sup Lee ◽  
Soon-Jae Lee
Keyword(s):  
Optical Properties ◽  
Aging Process ◽  
Significant Contribution ◽  
Asphalt Binder ◽  
Optical Characterization ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Oxidative Aging ◽  
Modified Binder

In between thermal-oxidative (heat and oxygen) and photo-oxidative (ultraviolet irradiation and oxygen) aging process of bitumen, photo-oxidative aging mainly depends on the optical properties of the asphalt binder. The higher the reflection (or the lower the absorption of the binders), the better the pavement serviceability. The literature review indicates that there is limited research conducted on the optical properties of the binder with wax additives. In this paper, the optical properties of commonly used binders (PG 64-22, Rubber modified binder, and SBS modified binder) containing wax additives (LEADCAP and Sasobit) were investigated using UV-Vis spectrometer. The result of this study showed that (1) the addition of modifiers (crumb rubber and SBS) with the base binder slightly increases the absorption of the binder; (2) the binder types and aging level have significant contribution on optical properties; (3) in general, the aged binders were observed to have higher reflectivity compared to the unaged binders; and (4) the addition of wax additives is observed to have a significant effect on the optical properties.

scholarly journals Material Properties and Environmental Benefits of Hot-Mix Asphalt Mixes Including Local Crumb Rubber Obtained from Scrap Tires

Environments ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 47
Author(s):  
Lim Min Khiong ◽  
Md. Safiuddin ◽  
Mohammad Abdul Mannan ◽  
Resdiansyah
Keyword(s):  
Asphalt Binder ◽  
Crumb Rubber ◽  
Environmental Benefits ◽  
Asphalt Binders ◽  
Rubber Content ◽  
Scrap Tires ◽  
Asphalt Mixes ◽  
Temperature Resistance ◽  
Modified Asphalt ◽  
Marshall Stability

This paper presents the results of a laboratory-based experimental investigation on the properties of asphalt binder and hot-mix asphalt (HMA) mixes modified by locally available crumb rubber, which was used as a partial replacement of asphalt by weight. In this study, fine crumb rubber with a particle size in the range of 0.3–0.6 mm, obtained from scrap tires, was added to the asphalt binder through the wet process. Crumb rubber contents of 5%, 10%, 15%, and 19% by weight of asphalt were added to the virgin binder in order to prepare the modified asphalt binder samples, while the unmodified asphalt binder was used as the control sample. The crumb rubber modified binder samples were examined for measuring viscosity indirectly using the penetration test, and temperature resistance using the softening point test. Later, both the modified and unmodified asphalt binders were used to produce HMA mixes. Two categories of HMA mix commonly used in Malaysia—namely, AC 14 (dense-graded) and SMA 14 (gap-graded)—were produced using the modified asphalt binders containing 5%, 10%, 15%, and 19% crumb rubber. Two AC 14 and SMA 14 control mixes were also produced, incorporating the unmodified asphalt binder (0% crumb rubber). All of the AC 14 and SMA 14 asphalt mixes were examined in order to determine their volumetric properties, such as bulk density, voids in total mix (VTM), voids in mineral aggregate (VMA), and voids filled with asphalt (VFA). In addition, the Marshall stability, Marshall flow, and stiffness of all of the AC 14 and SMA 14 mixes were determined. Test results indicated that the modified asphalt binders possessed higher viscosity and temperature resistance than the unmodified asphalt binder. The viscosity and temperature resistance of the asphalt binders increased with the increase in their crumb rubber content. The increased crumb rubber content also led to improvements in the volumetric properties (bulk density, VTM, VMA, and VFA) of the AC 14 and SMA 14 mixes. In addition, the performance characteristics of the AC 14 and SMA 14 mixes—such as Marshall stability, Marshall flow, and stiffness—increased with the increase in crumb rubber content. However, the AC 14 mixes performed much better than the SMA 14 mixes. The overall research findings suggest that crumb rubber can be used to produce durable and sustainable HMA mixes, with manifold environmental benefits, for use in flexible pavements carrying the heavy traffic load of highways.

Evaluation of Adhesion Properties of Modified Asphalt Binders with Use of Binder Bond Strength Test

2017 ◽  
Vol 2632 (1) ◽  
pp. 88-98 ◽  
Author(s):  
Weidong Huang ◽  
Lu Zhou
Keyword(s):  
Bond Strength ◽  
Asphalt Binder ◽  
Gel Permeation Chromatography ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Adhesion Properties ◽  
Rubber Powder ◽  
Positive Effects ◽  
Tracking Device ◽  
Styrene Butadiene

Moisture damage is a prominent problem of asphalt pavements. The bond strength between asphalt and aggregates is a crucial factor that influences the capability of asphalt to resist moisture-induced damage. In this study, a binder bond strength (BBS) test was conducted to evaluate the effects of various modifiers and additives of different amounts on bond strength between asphalt and aggregates. Furthermore, the influence of styrene–butadiene–styrene (SBS) on adhesion behavior of asphalt binder was investigated through a gel permeation chromatography (GPC) test. Finally, the results of the BBS test were compared with the findings obtained from a Hamburg wheel-tracking device (HWTD) test, which reflected the moisture sensitivity of mixtures under wet conditions. Results indicated that gilsonite, high-density polyethylene, and polyphosphoric acid improved the bond strength of the base asphalt; SBS had no positive effects on asphalt adhesion properties; and SBS at a low amount reduced the bond strength. Ethylene bis-stearamide wax, crumb rubber, terminal blend (TB) rubber powder, and compound modifier TB rubber powder plus SBS decreased the bond strength. The GPC test results showed that SBS possibly did not actively contribute to the formation of bond strength between asphalt and aggregates. Test data for BBS and HWTD tests under wet conditions confirmed that there was no discernible correlation between these two tests when adhesion properties of modified asphalts were evaluated. However, the results of the BBS test were in accordance with those of the HWTD test when the adhesion of asphalt with different amounts of the same modifier and the mixture resistance to water damage were evaluated.

scholarly journals Balancing the Performance and Environmental Concerns of Used Motor Oil as Rejuvenator in Asphalt Mixes

Recycling ◽  
2019 ◽  
Vol 4 (1) ◽  
pp. 11 ◽  
Author(s):  
Eslam Deef-Allah ◽  
Magdy Abdelrahman ◽  
Mark Fitch ◽  
Mohyeldin Ragab ◽  
Mousumi Bose ◽  
...  
Keyword(s):  
Environmental Protection Agency ◽  
Asphalt Binder ◽  
Crumb Rubber ◽  
Asphalt Binders ◽  
Environmental Concerns ◽  
Ethyl Benzene ◽  
Motor Oil ◽  
Asphalt Mixes ◽  
Used Motor Oil ◽  
The Us

Road deterioration inspires researchers to enhance the properties of asphalt binder for better performing mixes. Recycled tire rubber, or crumb rubber modifier (CRM), and used motor oil (UMO) are two modifiers that enhance asphalt binder performance through two different mechanisms. CRM affects high-temperature properties while UMO modifies low-temperature properties. Potential environmental concerns arising from the use of UMO have been raised in the literature. In this paper, the two recycled materials were investigated for their ability to complement each other. Both performance benefits of using both materials and the environmental concerns of using UMO were studied. Four CRM asphalt binders were investigated: two with UMO and two without UMO. Environmental impacts were evaluated using gas chromatography to check air emissions for benzene, toluene, ethyl-benzene, and xylenes (BTEX). The potential for toxic leaching of elements from modified hot mix asphalt (HMA) were checked using the US Environmental Protection Agency (EPA) Toxicity Characteristic Leaching Protocol (TCLP). For asphalt binders modified by CRM-UMO combinations, CRM decreased the amounts of released BTEX components, presumably by absorbing UMO and slowing the release of BTEX. Leaching results concluded that UMO mixtures showed a notable percentage of sulfur (S) as compared to non-UMO mixes. All these leachate components were under EPA limits.

scholarly journals Kinetic Viscoelasticity of Crosslinking Epoxy Asphalt

2019 ◽  
Vol 2673 (3) ◽  
pp. 551-560 ◽  
Author(s):  
Panos Apostolidis ◽  
Xueyan Liu ◽  
Martin van de Ven ◽  
Sandra Erkens ◽  
Tom Scarpas
Keyword(s):  
Mechanical Properties ◽  
Asphalt Binder ◽  
Crosslinking Density ◽  
Asphalt Binders ◽  
Experimental Program ◽  
Model Parameters ◽  
Epoxy Asphalt ◽  
Pavement Structures ◽  
Chemical Hardening ◽  
Modified Binder

Epoxy modification of asphalt binders has been recognized as a very effective technology to alter the chemistry of asphaltic materials in such a way that long-lasting pavement structures can be designed. However, the phenomena that are involved to build up the physico-mechanical properties of epoxy asphalt systems are still unknown. The focus of this paper is on understanding the link between chemistry and the mechanical properties of epoxy asphalt binders during the thermo-irreversible process of chemical hardening. For this purpose, a constitutive model for predicting the evolution of cure-induced stresses in epoxy asphalt binders is proposed, and an experimental program was developed to determine the model parameters. The cure dependency of physico-mechanical parameters of modified binder was obtained and imported into the model to simulate the build-up of material properties during (non-)isothermal hardening of epoxy asphalt binder. The model is implemented in a commercially finite element tool by coupling the chemical, thermal, and mechanical phenomena with multi-physics strategies, and the results are analyzed to identify the influence of different heating conditions on the crosslinking density and subsequently on stress build-up. It was found that the amount of stress build-up during curing was strongly dependent on the heating conditions, and a higher rate of stress build-up was observed at higher applied temperatures. In other words, the processing conditions during in-plant material production or in-field manufacturing of structures made by epoxy asphalt systems affect the material hardening and subsequently the desired functionalities of pavement structures.

scholarly journals Performance Evaluation of Crumb Rubber Asphalt Modified with Silicone-Based Warm Mix Additives

2020 ◽  
Vol 2020 ◽  
pp. 1-17 ◽  
Author(s):  
Nonde Lushinga ◽  
Liping Cao ◽  
Zejiao Dong ◽  
Chen Yang ◽  
Cyriaque O. Assogba
Keyword(s):  
Asphalt Binder ◽  
Fatigue Cracking ◽  
Crumb Rubber ◽  
Warm Mix Asphalt ◽  
Asphalt Binders ◽  
Water Repellent ◽  
Creep Recovery ◽  
Viscoelastic Continuum Damage ◽  
Warm Mix Additives ◽  
Different Temperatures

This research was conducted to elucidate better understanding of the performance of crumb rubber asphalt modified with silicone-based warm mix additives. Two different silicone-based warm mix asphalt (WMA) additives (herein Tego XP and Addibit) were used to prepare crumb rubber modified (CRM) warm mix asphalt binders. The viscosity of these CRM binders was measured at different temperatures and shearing rates. Furthermore, softening point and penetration tests, Multiple Stress Creep Recovery (MSCR), Time Sweep (TS), Atomic Force Microscopy (AFM), Frequency sweep (FS), and Fourier Transform Infrared (FTIR) tests were also conducted on prepared samples. Based on these robust and rigorous laboratory experiments, it was established that viscosity of CRM binders was reduced by addition of Tego XP and Addibit WMA additives. However, WMA additives had different influence on rheological properties of the binder. CRM binder with Tego XP improved resistance to rutting of the binders but would degrade the fatigue performance. On the contrary, viscoelastic continuum damage (VECD) model results and those of phase angle approach revealed that the binder with Addibit improved resistance to fatigue cracking of the binders but had no adverse effects on high temperature rutting performance. FTIR test results established a presence of polydimethylsiloxane (PDMS) in CRM binders with Tego XP and Addibit. PDMS is a well-known hydrophobic organic and inorganic polymer that is water repellent; therefore, binders containing these silicone-based warm mix additives could be beneficial in resisting moisture damage in asphalt binders and mixtures. Morphology of CRM binders with and without WMA revealed good distribution of the rubber particles in asphalt binder matrix. Further addition of WMA increased surface roughness of the binder, which can be correlated to changes in microstructure properties of the binder. Therefore, the study concluded that addition of Tego XP and Addibit reduces viscosity and improves mechanical properties of the asphalt binder.

Nonlinear Viscoelastic Response of Crumb Rubber Modified Asphalt Binder Under Large Strains

2020 ◽  
Vol 2674 (3) ◽  
pp. 139-149
Author(s):  
Saqib Gulzar ◽  
B. Shane Underwood
Keyword(s):  
Asphalt Binder ◽  
Crumb Rubber ◽  
Oscillatory Shear ◽  
Asphalt Binders ◽  
Large Strains ◽  
Viscoelastic Response ◽  
Modified Asphalt ◽  
Nonlinear Viscoelastic ◽  
Modified Asphalt Binder ◽  
Polymer Modified Asphalt

Agencies have been increasing their use of polymer modified asphalt binders in recent years to address performance issues and lengthen the useful life of their pavements. When deployed these materials likely experience strain levels exceeding their linear viscoelastic (LVE) limits. The same situation exists in non-polymer modified asphalt binders as well, but the effect may be more pronounced in polymer modified systems because of their bi-phasic nature. In this study, terminally blended crumb rubber (CR-TB) modified asphalt is studied to understand and quantify the nonlinear viscoelastic response under large strains. The CR-TB binders are extensively used in pavements subjected to high vehicular loads and extreme climatic conditions; thereby, their response under large strains becomes more critical. The current standard characterization techniques are based on LVE response using small amplitude oscillatory shear rheology only and do not consider the behavior of binders under large strains. In this study, large amplitude oscillatory shear (LAOS) rheology is used as a framework to more thoroughly investigate the complete response of the CR-TB modified asphalt binder under large strains at 30°C, 40°C, 50°C, and 60°C and at the frequencies of 0.5, 1, and 5 Hz. The LAOS response is analyzed using Fourier-transform rheology and the orthogonal stress decomposition method involving Chebyshev polynomial representation. It is found that nonlinearity manifests greatly in this study material as strain levels increase and frequencies decrease. The relative nonlinearity increases with increasing strain amplitude and is more significant towards lower end of the tested temperature range. The CR-TB binder shows strain-stiffening/softening and shear-thinning/thickening behavior depending upon a specific temperature, strain level, and frequency.

PHYSICAL PROPERTIES AND STORAGE STABILITY OF GEOPOLYMER MODIFIED ASPHALT BINDER

2016 ◽  
Vol 78 (7-2) ◽  
Author(s):  
Ahmad Nazrul Hakimi Ibrahim ◽  
Nur Izzi Md. Yusoff ◽  
Norliza Mohd Akhir ◽  
Muhamad Nazri Borhan
Keyword(s):  
Physical Properties ◽  
Storage Stability ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Binders ◽  
Modified Asphalt ◽  
Modified Asphalt Binder ◽  
Potential Alternative ◽  
Modified Binder ◽  
And Storage

This study was conducted to investigate the physical properties and storage stability of the 80/100 penetration grade asphalt modified with geopolymer. In this research, fly ash and alkali activators, namely sodium silicate (Na2SiO3) and sodium hydroxide (NaOH), were used as geopolymer components. The penetration, Ring and Ball softening point, ductility, and viscosity tests were conducted to determine the physical properties of geopolymer modified asphalt (GMA). Five samples of asphalt binders with varying percentages of geopolymer, namely 0, 3, 5, 7 and 9%, by weight of asphalt binder were studied. Results show that geopolymer has good compatibility with asphalt binder. The addition of geopolymer into asphalt binder resulted in improved permanent deformation resistance of the modified binder compared to that of the conventional asphalt. In conclusion, geopolymer could be considered as a potential alternative in the modification of the properties of asphalt binder.

Sign in / Sign up

Export Citation Format

Share Document