Study on the Mechanical Properties of Backfill Cream-Body during Coal Mining

2012 ◽  
Vol 170-173 ◽  
pp. 533-536 ◽  
Author(s):  
Shao Jie Chen ◽  
Wei Jia Guo ◽  
Hai Long Wang ◽  
Yi Tao Zhong
Keyword(s):  
Mechanical Properties ◽  
Coal Mine ◽  
Surface Mining ◽  
Test System ◽  
Control Surface ◽  
Ecological Environment ◽  
Uniaxial Compression Test ◽  
Mechanical Parameters ◽  
Test Results ◽  
Different Ages

In order to research the mechanical properties of the backfill cream-body under engineering conditions in the coal mine, the uniaxial compression test of backfill cream-body with different ages abtained from the filling locale of Daizhuang coal mine is conducted with MTS815.03 rock test system. The characteristics of backfill cream-body in the limited space and a certain environment are studied. Research shows that, the strength of backfill cream-body is high, but coagulability is bad and the discreteness of mechanical properties is different; Uniaxial compressive strength is 2.3 ~ 13.17 MPa and the average is 5.436 MPa; The elastic modulus is very low ,which is only 53.66 ~ 2614.35 MPa and the average is 645.14 MPa. The deformation is bigger when absorbing load; Poisson's ratio is low, which is only 0.0001 ~ 0.2112 and the average is 0.0265, which indicates that the backfill cream-body doesn't need the space of transverse deformation when bearing compression deformation; The mechanical parameters of backfill cream-body with different ages are fitted and regressed. Test results is important to control surface mining subsidence effectively, liberate the coal resources under buildings, railways and waterbodies and protect the ecological environment.

scholarly journals Research on Coal Mechanical Properties Based on True Triaxial Loading and Unloading Experiment

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Yanyan Peng ◽  
Haoxiang Deng ◽  
Minghong Xing ◽  
Pengfei Guo ◽  
Chun Zhu
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Principal Stress ◽  
Coal Mine ◽  
Test System ◽  
Intermediate Principal Stress ◽  
Mine Safety ◽  
Triaxial Loading ◽  
True Triaxial ◽  
Loading And Unloading

To study the safety issues caused by coal mine excavation, self-developed simulation of earth interior atmosphere and sound test system was used to perform true triaxial loading and unloading tests of coal. An acoustic emission detection system was used to record the damage evolution trend of coal under different intermediate principal stress states. The experimental results show that in the true triaxial unloading test, as the intermediate principal stress increases, the failure state of coal changes from shear failure to partial shear tension failure, finally leading to overall yield failure. In the stress-strain curves, with the increase in intermediate principal stress, the strain in the direction of intermediate principal stress gradually changes from compression to expansion, and typical expansion occurs. The Mogi–Coulomb strength criterion better reflects the strength failure characteristics of coal during unloading. The stress-acoustic emission diagrams show that the increase in intermediate principal stress causes the internal cracks of the coal to grow unsteadily and exponentially, and the increase in intermediate principal stress makes the coal lose its ability to continue to bear the load. Studying the influence of the intermediate principal stress on the mechanical properties of coal has practical significance for coal mine safety production.

scholarly journals Degradation of Strength and Stiffness of Sandstones Caused by Wetting-Drying Cycles: The Role of Mineral Composition

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Lu Chen ◽  
Yichao Rui ◽  
Yihan Zhao
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Moisture Content ◽  
Mechanical Parameters ◽  
Test Results ◽  
Strength And Stiffness ◽  
Rock Mechanical Properties ◽  
Mineral Constituents ◽  
Compressive Tests

Rock mechanical parameters are of great importance for the construction and design of rock engineering. Rocks are usually subjected to the deteriorating effect of cyclic wetting-drying because of the change in moisture content. The main objective of this study is to reveal the degradation effects of wetting-drying cycles on strength and modulus on varying rocks. Three kinds of sandstones with different mineral constituents are selected for testing. Artificial treatments of cyclic wetting-drying are conducted on respective specimens of the three sandstones (0, 10, 20, 30, and 40 cycles) to simulate the damage of rocks exposed to natural weathering. Uniaxial compressive tests are carried out on sandstone specimens to obtain their strength and modulus. Test results show that, for the tested sandstones, both of the uniaxial compressive strength (UCS) and modulus are reduced as the cyclic number rises. In the first ten cycles, the losses of UCS and modulus are very significant. Subsequently the changes of UCS and modulus become much more placid against cyclic number. When the cyclic number is the same, the loss percentages of rock mechanical properties of the three sandstones are very different which mainly depends on the contents of expandable and soluble minerals.

Sunlight exposure: the effects on the performance of paragliding fabric

2018 ◽  
Vol 69 (05) ◽  
pp. 381-389
Author(s):  
MENGÜÇ GAMZE SÜPÜREN ◽  
TEMEL EMRAH ◽  
BOZDOĞAN FARUK
Keyword(s):  
Mechanical Properties ◽  
Aging Process ◽  
Air Permeability ◽  
Sunlight Exposure ◽  
Test Results ◽  
Coating Materials ◽  
Strength Tests ◽  
Before And After ◽  
The Relationship ◽  
Dark Blue

This study was designed to explore the relationship between sunlight exposure and the mechanical properties of paragliding fabrics which have different colors, densities, yarn counts, and coating materials. This study exposed 5 different colors of paragliding fabrics (red, turquoise, dark blue, orange, and white) to intense sunlight for 150 hours during the summer from 9:00 a.m. to 3:00 p.m. for 5 days a week for 5 weeks. Before and after the UV radiation aging process, the air permeability, tensile strength, tear strength, and bursting strength tests were performed. Test results were also evaluated using statistical methods. According to the results, the fading of the turquoise fabric was found to be the highest among the studied fabrics. It was determined that there is a significant decrease in the mechanical properties of the fabrics after sunlight exposure. After aging, the fabrics become considerably weaker in the case of mechanical properties due to the degradation in both the dyestuff and macromolecular structure of the fiber

Framework and performance analysis of college English testing system based on data mining technology

2021 ◽  
pp. 1-11
Author(s):  
Liu Narengerile ◽  
Li Di ◽  
Keyword(s):  
Data Mining ◽  
Test System ◽  
Test Time ◽  
Testing System ◽  
Test Results ◽  
System Software ◽  
Examination System ◽  
Mining Technology ◽  
College English ◽  
And Performance

At present, the college English testing system has become an indispensable system in many universities. However, the English test system is not highly humanized due to problems such as unreasonable framework structure. This paper combines data mining technology to build a college English test framework. The college English test system software based on data mining mainly realizes the computer program to automatically generate test papers, set the test time to automatically judge the test takers’ test results, and give out results on the spot. The test takers log in to complete the test through the test system software. The examination system software solves the functions of printing test papers, arranging invigilation classrooms, invigilating teachers, invigilating process, collecting test papers, scoring and analyzing test papers in traditional examinations. Finally, this paper analyzes the performance of this paper through experimental research. The research results show that the system constructed in this paper has certain practical effects.

Finite Element Analysis of Reinforced Concrete Beams with Exterior FRP Shell

2011 ◽  
Vol 243-249 ◽  
pp. 1461-1465
Author(s):  
Chuan Min Zhang ◽  
Chao He Chen ◽  
Ye Fan Chen
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Contact Interface ◽  
Accurate Calculation ◽  
Element Analysis

The paper makes an analysis of the reinforced concrete beams with exterior FRP Shell in Finite Element, and compares it with the test results. The results show that, by means of this model, mechanical properties of reinforced concrete beams with exterior FRP shell can be predicted better. However, the larger the load, the larger deviation between calculated values and test values. Hence, if more accurate calculation is required, issues of contact interface between the reinforced concrete beams and the FRP shell should be taken into consideration.

Improving the Strength of Abrasive Wheels and Optimizing the Control over the Strength of Composite Abrasive Materials

2019 ◽  
Vol 946 ◽  
pp. 380-385
Author(s):  
Boris A. Chaplygin ◽  
Viacheslav V. Shirokov ◽  
Tat'yana A. Lisovskaya ◽  
Roman A. Lisovskiy
Keyword(s):  
Mechanical Properties ◽  
Test Results ◽  
Key Factors ◽  
Special Equipment ◽  
Material Density ◽  
Factors Affecting ◽  
Control Factors ◽  
Reinforcing Material ◽  
Special Studies ◽  
First Time

The strength of abrasive wheels is one of the key factors affecting the performance of abrasive machining. The paper discusses ways to improve the strength of abrasive wheels. The stress-state mathematical model presented herein is a generalization of the existing models. It is used herein to find for the first time that there are numerous optimal combinations of the elastic modulus and reinforcing material density, which result in the same minimum value of the objective function. It is found out that increasing the radius of the reinforcing component while also optimizing the mechanical properties of its material may increase the permissible breaking speed of the wheel several times. We herein present a regression equation and a nomogram for finding the optimal combination of control factors. Conventional methods for testing the mechanical properties of materials, which have been proven reliable for testing metals and alloys, are not as reliable for testing abrasive materials, as the test results they generate are not sufficiently stable or accurate. We therefore propose an alternative method that does not require any special equipment or special studies.

scholarly journals Evolution of Meniscal Biomechanical Properties with Growth: An Experimental and Numerical Study

2021 ◽  
Vol 8 (5) ◽  
pp. 70
Author(s):  
Marco Ferroni ◽  
Beatrice Belgio ◽  
Giuseppe M. Peretti ◽  
Alessia Di Giancamillo ◽  
Federica Boschetti
Keyword(s):  
Mechanical Properties ◽  
Stress Relaxation ◽  
Developmental Stage ◽  
Mechanical Response ◽  
Numerical Study ◽  
Numerical Models ◽  
Mechanical Stimulus ◽  
Specific Response ◽  
Mechanical Parameters ◽  
Biochemical Analyses

The menisci of the knee are complex fibro-cartilaginous tissues that play important roles in load bearing, shock absorption, joint lubrication, and stabilization. The objective of this study was to evaluate the interaction between the different meniscal tissue components (i.e., the solid matrix constituents and the fluid phase) and the mechanical response according to the developmental stage of the tissue. Menisci derived from partially and fully developed pigs were analyzed. We carried out biochemical analyses to quantify glycosaminoglycan (GAG) and DNA content according to the developmental stage. These values were related to tissue mechanical properties that were measured in vitro by performing compression and tension tests on meniscal specimens. Both compression and tension protocols consisted of multi-ramp stress–relaxation tests comprised of increasing strains followed by stress–relaxation to equilibrium. To better understand the mechanical response to different directions of mechanical stimulus and to relate it to the tissue structural composition and development, we performed numerical simulations that implemented different constitutive models (poro-elasticity, viscoelasticity, transversal isotropy, or combinations of the above) using the commercial software COMSOL Multiphysics. The numerical models also allowed us to determine several mechanical parameters that cannot be directly measured by experimental tests. The results of our investigation showed that the meniscus is a non-linear, anisotropic, non-homogeneous material: mechanical parameters increase with strain, depend on the direction of load, and vary among regions (anterior, central, and posterior). Preliminary numerical results showed the predominant role of the different tissue components depending on the mechanical stimulus. The outcomes of biochemical analyses related to mechanical properties confirmed the findings of the numerical models, suggesting a specific response of meniscal cells to the regional mechanical stimuli in the knee joint. During maturation, the increase in compressive moduli could be explained by cell differentiation from fibroblasts to metabolically active chondrocytes, as indicated by the found increase in GAG/DNA ratio. The changes of tensile mechanical response during development could be related to collagen II accumulation during growth. This study provides new information on the changes of tissue structural components during maturation and the relationship between tissue composition and mechanical response.

Durability of Red Mud Based Geopolymer Paste in Acid Solutions

2016 ◽  
Vol 866 ◽  
pp. 99-105 ◽  
Author(s):  
Smita Singh ◽  
M.U. Aswath ◽  
R.V. Ranganath
Keyword(s):  
Mechanical Properties ◽  
Acetic Acid ◽  
Fly Ash ◽  
Red Mud ◽  
Acetic Acid Solution ◽  
Strength Loss ◽  
Acid Solutions ◽  
Test Results ◽  
Acid Attack ◽  
Geopolymer Paste

The present investigation is on the effect of red mud on the mechanical properties and durability of the geopolymer paste in sulphuric and acetic acid solution. Red mud and fly ash were used to form the geopolymer paste along with the alkalies. The variation of red mud in the paste composition was from 0% to 90%. Cylindrical shaped specimens of 1 inch diameter and 1 inch height were prepared. The specimens were immersed in 5% sulphuric acid and 5% acetic acid for 1, 7, 14, 28, 56 and 84 days and tested for weight loss, visual deformation, strength loss and colour of the solvent, based on the procedure specified by ASTM C 267 – 01. SEM/EDX Tests were performed on the geopolymer specimens. Test results show that initially, the strength of the geopolymer increased upon the addition of red mud. The strength was maximum when the percentage of red mud was 30%. The maximum strength obtained was 38 MPa for the paste containing 30% red mud using 10M alkali solution as against 31.69 MPa, when only fly ash was used. Geopolymer paste containing 30% and 50% red mud showed better resistance to acid attack. The strength loss was minimum for the samples containing 30% red mud in both inorganic and organic acid i.e. sulphuric and acetic acid.

scholarly journals Strength and Microscopic Damage Mechanism of Yellow Sandstone with Holes under Freezing and Thawing

2020 ◽  
Vol 2020 ◽  
pp. 1-13 ◽  
Author(s):  
Huren Rong ◽  
Jingyu Gu ◽  
Miren Rong ◽  
Hong Liu ◽  
Jiayao Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Pore Size ◽  
Power Function ◽  
Damage Mechanism ◽  
Uniaxial Compression Test ◽  
Freezing And Thawing ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle ◽  
Microscopic Damage

In order to study the damage characteristics of the yellow sandstone containing pores under the freeze-thaw cycle, the uniaxial compression test of saturated water-stained yellow sandstones with different freeze-thaw cycles was carried out by rock servo press, the microstructure was qualitatively analyzed by Zeiss 508 stereo microscope, and the microdamage mechanism was quantitatively studied by using specific surface area and pore size analyzer. The mechanism of weakening mechanical properties of single-hole yellow sandstone was expounded from the perspective of microstructure. The results show the following. (1) The number of freeze-thaw cycles and single-pore diameter have significant effects on the strength and elastic modulus of the yellow sandstone; the more the freeze-thaw cycles and the larger the pore size, the lower the strength of the yellow sandstone. (2) The damage modes of the yellow sandstone containing pores under the freeze-thaw cycle are divided into five types, and the yellow sandstone with pores is divided into two areas: the periphery of the hole and the distance from the hole; as the number of freeze-thaw cycles increases, different regions show different microscopic damage patterns. (3) The damage degree of yellow sandstone is different with freeze-thaw cycle and pore size. Freeze-thaw not only affects the mechanical properties of yellow sandstone but also accelerates the damage process of pores. (4) The damage of the yellow sandstone by freeze-thaw is logarithmic function, and the damage of the yellow sandstone is a power function. The damage equation of the yellow sandstone with pores under the freezing and thawing is a log-power function nonlinear change law and presents a good correlation.

Sign in / Sign up

Export Citation Format

Share Document