The Comparative Analysis of Wood-Plastic Raw Material to Heat up the Experiment and Simulation of Heat Transfer Process

2012 ◽  
Vol 217-219 ◽  
pp. 559-562
Author(s):  
Yue Tang ◽  
Gang Liu

The authors use the semi-infinite objects unsteady heat conduction theory analysis of the dry thermal conductivity of wood-plastic raw materials.The correspondence between theoretical calculations obtained wood-plastic material thickness and heating time, to determine the impact of wood-plastic raw materials in the water on the thermal diffusivity. ANSYS software material preheating and drying heat transfer to simulate the process to draw the curve of the relationship between temperature and time of the temperature rise process of wood-plastic raw materials, raw material moisture content of wood-plastic temperature changes. The comparative analysis of experimental results and simulation results are similar, and provides a reference for the study of predrying of wood-plastic raw materials.

Author(s):  
Sami Missaoui ◽  
Zied Driss ◽  
Romdhane Ben Slama ◽  
Bechir Chaouachi

This study presents a coupled model to simulate the heat transfer process between the helical condenser coil and the water inside the tank. This coupled model was developed using ANSYS Fluent Computational Fluid Dynamics (CFD). The heat flux of the condenser coils is obtained from our experimental investigation and delivered as initial boundary conditions to the tank model. The results obtained are considered essential and are, in turn, capable of assessing the performance of the modified domestic refrigerator for the production of hot water. According to this model, the results confirmed that the coefficient of heat transfer and the performance of the system decreased with an increase in the heating time. The natural heat transfer coefficient Uc falls from 727.26[Formula: see text]W [Formula: see text] m[Formula: see text] [Formula: see text] K[Formula: see text] to 68.64[Formula: see text]W [Formula: see text] m[Formula: see text] [Formula: see text] K[Formula: see text] during the total heating cycle, and the water temperature rises from 20∘C to 50.73∘C. In addition, the impact of water temperature on the evaporating region was used in this analysis. Therefore, the temperature of the evaporator is unaffected by the development of hot water. As a result, these outcomes will be used for the development of the domestic refrigerator with immersed condenser coil.


2020 ◽  
Vol 10 (1) ◽  
pp. 49
Author(s):  
Suharto Suharto ◽  
Muhammad Amin ◽  
Muhammad Al Muttaqii ◽  
Syafriadi Syafriadi ◽  
Kiki Nurwanti

Experimental study on the use of basalt stone originated from Lampung has been conducted to evaluate its potential for a partial substitute of raw material in production of cement clinker. The basalt stone contains minerals of anorthite, augite, and albite phases that are required for clinker formation. In this study, the main raw materials were 80% limestone, 10% silica sand, 9% clay and 1% iron sand. The raw material in these experiments were mixtures 90% or 80% of the main raw material and 10% or 20% of basalt stone. The effect of adding coal to raw materials was also studied to see the possibility of an increase in clinkerization temperature inside the raw material mixture, and at the same time to see the effect of coal ash on clinker composition. Clinker obtained from heating of raw materials at a temperature of 1100oC had LSF of 94.1% and 95.1% (heating time of 1 and 3 hours). If heating is carried out at 1200oC, the clinker had LSF of 97.7% and 98.0% (heating time of 2 and 3 hours, respectively). Depending on the temperature and duration of heating, the clinker mostly had SM in the range of 2.18-2.40% , and AM in the range of 0,78-1.80%. Characterization using XRD showed that the clinker consisted of larnite and gehlenite phases, and dominated by CaO.Batu basalt Lampung telah diuji potensinya sebagai pengganti sebagian bahan baku utama pembuatan klinker semen. Batu basalt tersebut memiliki mineral-mineral dalam fase anorthite, augite, dan albite yang diperlukan pada pembentukan klinker. Pada penelitian ini, bahan baku utama adalah batu kapur 80%, pasir silika 10%, tanah liat 9% dan pasir besi 1%. Campuran bahan baku klinker adalah 90% atau 80% bahan baku utama dan 10% atau 20% batu basalt. Efek penambahan batubara ke dalam bahan baku klinker juga dipelajari untuk melihat kemungkinan kenaikan temperatur klinkerisasi di dalam campuran bahan baku, dan sekaligus untuk melihat efek abu batubara terhadap komposisi klinker. Klinker hasil pemanasan bahan baku pada temperatur 1100oC memiliki LSF 94,1% dan 95,1% (lama pemanasan 1 dan 3 jam). Jika pemanasan dilakukan pada 1200oC, klinker memilik LSF 97,7% dan 98,00% (lama pemanasan 2 dan 3 jam). Tergantung pada temperatur dan lama pemanasan, klinker hasil percobaan ini umumnya memiliki SM 2,18-2,40%, dan AM antara 0,78-1,80%. Karakterisasi dengan XRD menunjukkan bahwa klinker terdiri dari fase larnite dan gehlenite, dan didominasi CaO.


2020 ◽  
Vol 12 (24) ◽  
pp. 10454
Author(s):  
Katarína Teplická ◽  
Martin Straka

This article summarizes the arguments within the scientific discussion on the issue of using mining machines and their life cycle. The main goal of the article is to investigate the impact of a combination of mobile and stationary mining machines and their optimal distribution in the mining process to increase the efficiency of mining and processing of raw materials. The following methods of research were focused on the use of technical indicators for the valuation efficiency of the mining process: a simulation method was used for the distribution of mining machines, comparison analysis was used for the real and past state of mining machines, and a decision tree was used as managerial instrument for optimal alternatives of mining machines. The research empirically confirms and theoretically proves that optimal distribution of mining machines and machine parks is very important for mining companies. The benefit of this research for the mining company was the new location of the machines and the combination of stationary production lines and mobile equipment. The optimal layout of the machines reduced the number of conveyor belts and improved the transfer of limestone processing to mobile devices, saving time, which was reflected in transport costs. The results can be useful for other mining companies seeking to create an optimal machine park.


2011 ◽  
Vol 393-395 ◽  
pp. 412-415
Author(s):  
Jian Hua Zhong ◽  
Li Ming Jiang ◽  
Kai Feng

In this article, finned copper tube used in the central air conditioning was acted as the discussed object. According to the combination with actual processing and theoretical calculations, Five finned tube was selected with typical structural parameters, and established their entity model using Pro/E, then the heat transfer process of finned tube was simulated through the ANSYS, the effect of the fin height, fin thickness and other structure parameters to the heat transfer enhancement of finned tube was researched. Meantime the efficiency of the heat transfer under different convection heat transfer coefficient was also studied.


Author(s):  
Б.Т. Базарова ◽  
Б.Қ. Копбулсынова ◽  
Ж.А. Аймешева ◽  
B. Bazarova ◽  
B. Kopbulsynova ◽  
...  

Батыс Қазақстан облысындағы кәсіпорындардың эволюциясы экономикалық дамудың жалпы циклдік сипатына байланысты да, әр түрлі сыртқы және ішкі факторлардың осы салаға әсер етуінен, сондай-ақ даму процесінде сөзсіз ауытқулар салдарынан ауытқуларға ұшырайды. Батыс Қазақстан облысының аймақтық агроөнеркәсіптік кешенін тұрақты дамытудың басымдықтары талдау арқылы анықталуы керек. Зерттеудің мақсаты - Батыс Қазақстан облысының агроөнеркәсіптік кешенінің тиімді және тұрақты дамуын зерттеу болып табылады. Бұл тақырыпты зерттеу кезінде статистикалық-экономикалық әдіс, талдау және синтез қолданылды. Ауылшаруашылық кешенінің жеке аймақ ретінде тұрақты дамуы да, жалпы елдің де дамуы ауылшаруашылық кешенінің тұрақты қалыптасуынсыз мүмкін емес, себебі оның түпкі өнімі қайта өңдеу өнеркәсібі болып табылады, ал оның мақсаты - талаптарына сай халықты сапалы өніммен қамтамасыз ету. Талдау көрсеткендей, ауылшаруашылық өндірісінің қазіргі жағдайы, қолайсыз факторлардың әсерінің күшеюімен сипатталады, ең алдымен табиғи факторлардың өндірісінде, жалпы өсімдік шаруашылығы өнімінің жылдық айырмашылықтарын тудырады, және өз кезегінде мал шаруашылығындағы ауытқуларға әкеледі, сонымен қатар оның әсері өңдеуші салаларда сезіледі, ал бұл өнеркәсіптің шикізаты болып табылады. Зертеу барысында 2015 жылдан бастап Батыс Қазақстан облысының аумағында ауыл шаруашылығы өнімдері өндірісінің күрт төмендегені анықталды, бұл жалпы, сондай-ақ өсімдік шаруашылығы мен мал шаруашылығы салалары бойынша да өндіріс тұрақтылығының төмендеуіне әкелді, және ол бүгінгі күнге дейін жалғасуда. Агроөнеркәсіптік кешеннің шикізат саласындағы өндіріс тұрақтылығының төмендеуі қайта өңдеу өнеркәсібі өнімдерін өндіруде ауытқулардың артуына әкеліп соқтырды, бұның нәтижесінде халыққа азық-түлік өнімдерін ұсынуда тұрақсыздық пайда болды. Батыс Қазақстан облысының АӨК-ін оның салаларының өнімділігі мен кірістілігін арттыруға бағытталған одан әрі дамыту өндірісті жаңғыртуды және қайта жарақтандыруды, оның инфрақұрылымын дамытуды және салалық кластерлерді қалыптастыруды талап етеді. Кілт сөздер: агроөнеркәсіп кешені, тербеліс, аграрлық сектор, өндіріс, халық саны, агротехника, экономика, талдау, өнімдер, өсімдік шаруашылығы. The evolution of enterprise in the West Kazakhstan region is subject to fluctuations due to both the general cyclical nature of economic development and the impact of various external and internal factors on this industry, as also fluctuations unavoidable in the evolution process. The priorities for sustainable evolution of the regional agro-industrial complex of the West Kazakhstan region should be identified through analysis. The goal of the research is to study the effective and sustainable development of the agro-industrial complex of the West Kazakhstan region. Through studies this topic, the statistical-economic method, analysis and synthesis were used. Sustainable development of the agro-industrial complex of both a particular region and the country as a whole is impossible without the stable functioning of its core - agriculture, the final product of which is used by the processing industry, whose goal is to provide the population with high-quality products in volumes that meet their requirements. Current state of agricultural production, as the analysis shows, is characterized by an increase in the influence of unfavorable factors on production, first of all natural ones, which cause annual differences in the production of gross crop production, which, in turn, convey fluctuations to the livestock industry and, as a result, affects the processing industries. it is the raw material of the industry. In the course of the study, it was found that, since 2015, in the territory of the West Kazakhstan region, there has been a sharp decline in agricultural production, which led to a decrease in the stability of production in general, and in the fields of crop and livestock production, which continues to the present. A decrease in the sustainability of production in the raw materials sector of the agro-industrial complex entailed an increase in fluctuations in the production of products of the processing industry, which ultimately resulted in the emergence of an instability in the supply of food to the population. Further development of the agro-industrial complex of the West Kazakhstan region, aimed at increasing the productivity and profitability of its industries, requires the modernization and re-equipment of production, the development of its infrastructure and the formation of industry clusters.


2020 ◽  
Vol 8 ◽  
Author(s):  
Duygu Karabelli ◽  
Steffen Kiemel ◽  
Soumya Singh ◽  
Jan Koller ◽  
Simone Ehrenberger ◽  
...  

The growing number of Electric Vehicles poses a serious challenge at the end-of-life for battery manufacturers and recyclers. Manufacturers need access to strategic or critical materials for the production of a battery system. Recycling of end-of-life electric vehicle batteries may ensure a constant supply of critical materials, thereby closing the material cycle in the context of a circular economy. However, the resource-use per cell and thus its chemistry is constantly changing, due to supply disruption or sharply rising costs of certain raw materials along with higher performance expectations from electric vehicle-batteries. It is vital to further explore the nickel-rich cathodes, as they promise to overcome the resource and cost problems. With this study, we aim to analyze the expected development of dominant cell chemistries of Lithium-Ion Batteries until 2030, followed by an analysis of the raw materials availability. This is accomplished with the help of research studies and additional experts’ survey which defines the scenarios to estimate the battery chemistry evolution and the effect it has on a circular economy. In our results, we will discuss the annual demand for global e-mobility by 2030 and the impact of Nickel-Manganese-Cobalt based cathode chemistries on a sustainable economy. Estimations beyond 2030 are subject to high uncertainty due to the potential market penetration of innovative technologies that are currently under research (e.g. solid-state Lithium-Ion and/or sodium-based batteries).


2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ana Jamile Damasceno Barbosa ◽  
Vitor Hugo de Paiva Santos ◽  
Priscilla Cavalcante de Araújo ◽  
Felipe Lucas de Medeiros ◽  
Letícia Yasmin da Silva Otaviano

PurposeThe paper aims to propose the development of an eco product to replace the traditional cotton swab that meets the expected needs, besides having a bias based on sustainability and economic viability.Design/methodology/approachThe applied nature article opted for an exploratory and descriptive study, with the objective of seeking a solution to a real problem: to reduce the environmental impact in the disposal of cotton swabs. To test this hypothesis, the exploratory stage evaluated the literature on the principles of eco design and environmental marketing to understand market viability and environmental impacts. The descriptive phase presented a comparative analysis between the original product and the proposed one, in terms of production processes and impacts of the product life cycle. Thus, an alternative product was conceived and validated applying the life cycle analysis (LCA).FindingsThe paper provides a comparative analysis between the eco product and the traditional product in order to validate the hypothesis that the new proposal reduces the environmental impact. It was found that both productive processes have similar impacts; however, the raw material of the proposed eco product demonstrated a significant reduction in the impact caused on the environment, considering cradle to cradle analysis.Originality/valueThis paper conceives an eco product as an alternative to traditional cotton swab, presenting an innovative potential in line with worldwide sustainability trends.


Author(s):  
Kausar Sultan Shah ◽  
Safi Ur Rehman

The key factor behind raw mix design in the cement factory is the appropriate production planning, resulting in high-quality raw material. Quarry managers usually come up with uncertainty-related raw materials due to variations in chemical composition. These uncertainties required efficient planning in terms of useful insight into this problem. This research provides a detailed explanation of scenario analysis of raw materials used in cement manufacturing using Monte Carlo simulation (MCS) and indices. Scenario analysis is used to predict the possibility of best, worst and most likely cases of raw material’s quality. Whereas, Monte Carlo simulation is used to evaluate the inherent uncertainty associated with chemical composition values in order to analyze the impact of truly unpredictable scenarios. The predictive results help in decisions related to production planning, raw mix design optimization and increasing the probability of designing the best plan.


2019 ◽  
Vol 6 (4) ◽  
pp. 791 ◽  
Author(s):  
Eraldo Antonio Bonfatti Júnior ◽  
Elaine Cristina Lengowski ◽  
Alan Sulato de Andrade ◽  
Ivan Venson ◽  
Umberto Klock ◽  
...  

Despite of the wide use worldwide, the industrial potential of bamboo species in Brazil is not much investigated. However, some encouragement to revert this situation was created in last few years. The aim of this research was to evaluate the technological characteristics of the Bambusa vulgaris biomass for the production of pulp by the kraft process. The technological characteristics of the raw material were determined by the basic density, the chemical composition and the morphology of the fibers. The cooking process was carried out with the application of eight charges of active alkali, in 90 minutes of heating time and 60 minutes in the maximum temperature of 170ºC. All analyzes were also executed with the Eucalyptus spp. and the Pinus spp., in order to make a complete comparison among the species Bambusa vulgaris and the two most used raw materials for the pulp production in Brazil. The Bambusa vulgaris presented a higher basic density, lower holocellulose content and a higher total extractive content. Its fibers have intermediate length and wall thickness, similar to the Eucalyptus spp. and the Pinus spp. Considering the kraft pulping process, the species Bambusa vulgaris demonstrated to be easier to delignify besides presenting almost zero reject content and smaller consumption of active alkali. However, the Eucalyptus spp. and the Pinus spp. obtained the best yields, the lowest specific consumption of raw material and better selectivities.


2018 ◽  
Vol 14 (1) ◽  
Author(s):  
Intan Purwatianingsih Sihadi ◽  
Sifrid S. Pangemanan ◽  
Hendrik Gamaliel

Constraints are activities that prevent companies from carrying out production activities. Along with the increasingly competitive world economy today, industrial companies are required to be more sensitive in anticipating constraints that occur both internally and externally. These constraints must be considered by the company because it can hamper the production process which has an impact on production costs as well as sales volumes which ultimately cause losses to the company. One tool that can identify constraints of a company is the Constraint Theory. This study aims to find out what constraints occur in the production process and the impact of these constraints on production costs. The method used in this study is descriptive. The results of this study are internal constraints are engine damage and external constraints are delays in the delivery of raw materials. The impact of these constraints on production costs is the loss of raw material costs and an increase in factory overhead costs.Keywords: Constraints, Production Cost, Theory of Constraint


Sign in / Sign up

Export Citation Format

Share Document