A CMOS Bandgap References Voltage Circuit Using Current Conveyor for Power Management Applications

2013 ◽  
Vol 385-386 ◽  
pp. 1335-1339 ◽  
Author(s):  
Min Chin Lee ◽  
Chi Jing Hu
Keyword(s):  
Power Dissipation ◽  
Supply Voltage ◽  
Reference Voltage ◽  
Cmos Process ◽  
Bandgap Reference ◽  
Output Resistance ◽  
Operation Temperature ◽  
Resistive Loading ◽  
Chip Size ◽  
Is Design

This paper proposes a low power bandgap reference voltage circuit that provides an output reference voltage close to the bandgap voltage having a low output resistance and allows resistive loading. This proposed circuit is design and implemented using the TSMC 0.18μm 1P6M CMOS process. Simulation and measured results verify that the chip size is with power dissipation about 0.1mW, and the operation temperature range formwith temperature coefficient about . The chip supply voltage can from 1.3 to 1.8V with PSRR about 70 dB, and its output reference voltage can stable on .

Implementation of Low Bandgap Reference Voltage Circuit for Power Management Applications

2012 ◽  
Vol 562-564 ◽  
pp. 1517-1521 ◽  
Author(s):  
Min Chin Lee ◽  
Ming Chia Hsie ◽  
Chi Jing Hu
Keyword(s):  
Low Temperature ◽  
Temperature Coefficient ◽  
Power Management ◽  
Power Dissipation ◽  
Reference Voltage ◽  
Bandgap Reference ◽  
Low Bandgap ◽  
Operation Temperature ◽  
Chip Size ◽  
Is Design

This paper proposes a low bandgap reference voltage circuit with low temperature coefficient and independent of suply voltage for applications to power management IC. This proposed circuit is design and implemented using the TSMC 0.35μm CMOS 2P4M process. Based on simulated and measured results , the chip size is 20.6000.680mm with power dissipation about 3.3mW, and the operation temperature range form 0Cto 100C with temperature coefficient about 9.29/ppmC. The chip suply voltage can from 2.9V to 3.3V with PSRR about 44.2 dB, and its output reference voltage can stable at 0.65V.

scholarly journals None Operational Amplifier (OPA) Based: Design of Analogous Bandgap Reference Voltage

2018 ◽  
Vol 201 ◽  
pp. 02002
Author(s):  
Hao-Ping Chan ◽  
Yu-Cherng Hung
Keyword(s):  
Temperature Coefficient ◽  
Operational Amplifier ◽  
Supply Voltage ◽  
Reference Voltage ◽  
Cmos Process ◽  
Bandgap Reference ◽  
Chip Design ◽  
Chip Area ◽  
Voltage Variation ◽  
Current Variation

By using 0.35-um CMOS process, this work achieves a design of analogous band-gap reference voltage circuit with low temperature coefficient. The proposed circuit operates at 3V and generates a reference current of 44 uA. The HSPICE simulation results show the temperature coefficient of this circuit is 23 ppm/°C at range of -10 °C to 100 °C, and the line regulation (the ratio of output current variation to supply voltage variation) is estimated as 1.95 uA/V from supply voltage variation of 3 V to 5 V. The experimental chip is fabricated and measured. The circuit provides adjustable capability for output voltage among temperature variation of -10 - 100 °C. The chip area is 534 × 695 um2. In this new design, the operational amplifier is not necessary. The chip design effort can be great reduced.

scholarly journals None Operational Amplifier (OPA) Based: Design of Analogous Bandgap Reference Voltage

2016 ◽  
Author(s):  
Hao-Ping Chan ◽  
Yu-Cherng Hung
Keyword(s):  
Temperature Coefficient ◽  
Operational Amplifier ◽  
Supply Voltage ◽  
Reference Voltage ◽  
Cmos Process ◽  
Bandgap Reference ◽  
Chip Design ◽  
Chip Area ◽  
Voltage Variation ◽  
Current Variation

By using 0.35-um CMOS process, this work achieves a design of analogous band-gap reference voltage circuit with low temperature coefficient. The proposed circuit operates at 3V and generates a reference current of 44 uA. The HSPICE simulation results show the temperature coefficient of this circuit is 23 ppm/℃ at range of -10 ℃ to 100 ℃, and the line regulation (the ratio of output current variation to supply voltage variation) is estimated as 1.95 uA/V from supply voltage variation of 3 V to 5 V. The experimental chip is fabricated and measured. The circuit provides adjustable capability for output voltage among temperature variation of -10 - 100 ℃. The chip area is 534 × 695 um^2. In this new design, the operational amplifier is not necessary. The chip design effort can be great reduced.

The Design of Bandgap Reference Based on Empyrean Aether Software

2014 ◽  
Vol 687-691 ◽  
pp. 3489-3493
Author(s):  
Wei Qu ◽  
Li Mei Hou ◽  
Xiao Xin Sun ◽  
Jing Yu Sun ◽  
Liang Yu Li
Keyword(s):  
High Performance ◽  
Supply Voltage ◽  
Design Method ◽  
Reference Voltage ◽  
Voltage Source ◽  
Reference Source ◽  
Cmos Process ◽  
Bandgap Reference ◽  
Power Supply Voltage ◽  
Reference Voltage Source

A high-performance bandgap reference voltage source design method is proposed in this paper, according to the shortcomings of traditional bandgap reference voltage source. This method combined CSMC 0.35μm CMOS process with Aether software technology, enabling to improve the bandgap reference source op amp performance and take into account accuracy and stability of the system. From the experimental results: this bandgap reference voltage source output voltage has changed about 63 mV when the temperature varied from to , and the line regulator is 0.4mV/V when the power supply voltage varied from 3.2V to 3.3V. This system has advantages of high accuracy and good stability.

A Curvature-Compensated, High Power Supply Rejection CMOS Bandgap Reference for MEMS Micro-Accelerometer

2011 ◽  
Vol 483 ◽  
pp. 481-486 ◽  
Author(s):  
Xiao Wei Liu ◽  
Bing Jun Lv ◽  
Peng Fei Wang ◽  
Liang Yin ◽  
Na Xu
Keyword(s):  
Temperature Coefficient ◽  
High Power ◽  
Power Supply ◽  
Supply Voltage ◽  
Reference Voltage ◽  
Cmos Process ◽  
Bandgap Reference ◽  
Power Supply Rejection Ratio ◽  
Compensation Technique ◽  
Supply Rejection

The reference is an important part in the accelerometer system. With the development of science and technology, the request of the performance of accelerometers is increasingly higher and the precision of reference directly affects the performance of accelerometers. Therefore, a reference voltage applicable to accelerometers is presented based on the analysis of basic principles of conventional bandgap reference (BGR) in this paper. A high-order curvature compensation technique, which uses a temperature dependent resistor ratio generated by a high poly resistor and a nwell resistor, effectively serves to reduce temperature coefficient of proposed reference voltage circuit and to a large extent improve its performance. To achieve a high power supply rejection ratio (PSRR) over a broad frequency range, a pre-regulator is introduced to remain the supply voltage of the core circuit of BGR relatively independent of the global supply voltage. The proposed circuitry is designed in standard 2.0μm CMOS process. The simulated result shows that the average temperature coefficient is less than 2ppm/°C in the temperature range from -40 to 120°C. The improvement on temperature coefficient (TC) is about 10 times reduction compared to the conventional approach. And the PSR at DC frequency and 1kHz achieves -107 and -71dB respectively at 9.0V supply voltage.

scholarly journals Design of Low Power and Low Phase Noise Current Starved Ring Oscillator for RFID Tag EEPROM

2019 ◽  
pp. 19-23
Keyword(s):  
Low Power ◽  
Phase Noise ◽  
Power Dissipation ◽  
Supply Voltage ◽  
Ring Oscillator ◽  
Cmos Process ◽  
Clock Signal ◽  
Voltage Level ◽  
Rfid Tag ◽  
Low Phase Noise

Power dissipation of CMOS IC is a key factor in low power applications especially in RFID tag memories. Generally, tag memories like electrically erasable programmable read-only memory (EEPROM) require an internal clock generator to regulate the internal voltage level properly. In EEPROM, oscillator circuit can generate any periodic clock signal for frequency translation. Among different types of oscillators, a current starved ring oscillator (CSRO) is described in this research due to its very low current biasing source, which in turn restrict the current flows to reduce the overall power dissipation. The designed CSRO is limited to three stages to reduce the power dissipation to meet the specs. The simulated output shows that, the improved CSRO dissipates only 4.9 mW under the power supply voltage (VDD) 1.2 V in Silterra 130 nm CMOS process. Moreover, this designed oscillator has the lowest phase noise -119.38 dBc/Hz compared to other research works. In addition, the designed CSRO is able to reduce the overall chip area, which is only 0.00114 mm2. Therefore, this proposed low power and low phase noise CSRO will be able to regulate the voltage level successfully for low power RFID tag EEPROM.

High-Swing, High-Resolution, Low-Power, Low-Area Voltage-Mode LTA/WTA Circuits

2015 ◽  
Vol 24 (07) ◽  
pp. 1550103 ◽  
Author(s):  
Mohammad Soleimani ◽  
Siroos Toofan ◽  
Mostafa Yargholi
Keyword(s):  
High Resolution ◽  
Low Power ◽  
Power Dissipation ◽  
Supply Voltage ◽  
Rank Order ◽  
Active Area ◽  
Total Power ◽  
Common Source ◽  
Cmos Process ◽  
Process Technology

In this paper, a general architecture for analog implementation of loser/winner-take-all (LTA/WTA) and other rank order circuits is presented. This architecture is composed of a differential amplifier with merged n-inputs and a merged common-source with active load (MCSAL) circuit to choose the desired input. The advantages of the proposed structure are simplicity, very high resolution, very low supply voltage requirements, very low output resistor, low power dissipation, low active area and simple expansion for multiple inputs by adding only three transistors for each extra input. The post-layout simulation results of proposed circuits are presented by HSPICE software in 0.35-μm CMOS process technology. The total power dissipation of proposed circuits is about 110-μW. Also, the total active area is about 550-μm2 for five-input proposed circuits, and would be negligibly increased for each extra input.

scholarly journals A 0.8 V 0.23 nW 1.5 ns Full-Swing Pass-Transistor XOR Gate in 130 nm CMOS

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Nabihah Ahmad ◽  
Rezaul Hasan
Keyword(s):  
Circuit Design ◽  
Power Dissipation ◽  
Low Voltage ◽  
Supply Voltage ◽  
Propagation Delay ◽  
Cmos Process ◽  
Xor Gate ◽  
Power Efficient ◽  
Pass Transistor ◽  
Full Swing

A power efficient circuit topology is proposed to implement a low-voltage CMOS 2-input pass-transistor XOR gate. This design aims to minimize power dissipation and reduce transistor count while at the same time reducing the propagation delay. The XOR gate utilizes six transistors to achieve a compact circuit design and was fabricated using the 130 nm IBM CMOS process. The performance of the XOR circuit was validated against other XOR gate designs through simulations using the same 130 nm CMOS process. The area of the core circuit is only about 56 sq · µm with 1.5659 ns propagation delay and 0.2312 nW power dissipation at 0.8 V supply voltage. The proposed six-transistor implementation thus compares favorably with other existing XOR gate designs.

Implementation and Design of Voltage-Mode PFM Control Buck Power Converter

2013 ◽  
Vol 860-863 ◽  
pp. 2390-2394
Author(s):  
Min Chin Lee ◽  
Ruey Wun Jan
Keyword(s):  
Supply Voltage ◽  
Pulse Frequency ◽  
Power Converter ◽  
Buck Converter ◽  
Switching Frequency ◽  
Cmos Process ◽  
Pulse Frequency Modulation ◽  
Better Regulation ◽  
Chip Size ◽  
Voltage Feedback

A lower power consumption, smaller output ripple and better regulation buck dcdc converter controlled by voltage feedback and pulse-frequency modulation (PFM) mode is implemented in this paper. The converter operating in discontinuous conduction mode (DCM) is designed and simulated using the TSMC 0.18μm 1P6M CMOS Process. Hspice simulation results show that, the buck converter having chip size with power dissipation about 0.68mW. This chip can operate with input supply voltage from 1.2V to 1.8V, and switching frequency from 249KHz () to 50KHz (), and its output voltage can stable at 1.0V and less than 110mV ripple voltage at maximum loading current 100 mA.

scholarly journals A 65 nm Duplex Transconductance Path Up-Conversion Mixer for 24 GHz Automotive Short-Range Radar Sensor Applications

Sensors ◽  
2022 ◽  
Vol 22 (2) ◽  
pp. 594
Author(s):  
Tahesin Samira Delwar ◽  
Abrar Siddique ◽  
Manas Ranjan Biswal ◽  
Prangyadarsini Behera ◽  
Yeji Choi ◽  
...  
Keyword(s):  
Power Dissipation ◽  
Short Range ◽  
Noise Figure ◽  
Supply Voltage ◽  
Common Source ◽  
Cmos Process ◽  
Radar Sensor ◽  
Sensor Applications ◽  
The Common ◽  
24 Ghz

A 24 GHz highly-linear upconversion mixer, based on a duplex transconductance path (DTP), is proposed for automotive short-range radar sensor applications using the 65-nm CMOS process. A mixer with an enhanced transconductance stage consisting of a DTP is presented to improve linearity. The main transconductance path (MTP) of the DTP includes a common source (CS) amplifier, while the secondary transconductance path (STP) of the DTP is implemented as an improved cross-quad transconductor (ICQT). Two inductors with a bypass capacitor are connected at the common nodes of the transconductance stage and switching stage of the mixer, which acts as a resonator and helps to improve the gain and isolation of the designed mixer. According to the measured results, at 24 GHz the proposed mixer shows that the linearity of output 1-dB compression point (OP1dB) is 3.9 dBm. And the input 1-dB compression point (IP1dB) is 0.9 dBm. Moreover, a maximum conversion gain (CG) of 2.49 dB and a noise figure (NF) of 3.9 dB is achieved in the designed mixer. When the supply voltage is 1.2 V, the power dissipation of the mixer is 3.24 mW. The mixer chip occupies an area of 0.42 mm2.

Sign in / Sign up

Export Citation Format

Share Document