Possibilities of Using Alternative Materials as a Substitute Binder or Filler into Composites

2015 ◽  
Vol 1105 ◽  
pp. 31-35 ◽  
Author(s):  
Nadežda Števulová ◽  
Ivana Schwarzova ◽  
Viola Hospodarova ◽  
Jozef Junak ◽  
Marcela Ondova ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Coal Fly Ash ◽  
Steel Slag ◽  
Recycled Concrete ◽  
Partial Replacement ◽  
Alternative Materials ◽  
Activated Coal ◽  
Hemp Fibres ◽  
Lightweight Composites

This article reports on the possibilities of using selected alternative materials like hemp fibres, MgO-cement, recycled concrete, fly ash and steel slag as binder or filler replacement in composite materials in civil engineering production. These binder or filler substitutes were mixed into composites and their compressive strength was tested. The paper is divided into four parts providing the results of experiments. In first part strength parameters of lightweight composites based on natural fibres (hemp hurds) and alternative binder (MgO-cement) are presented. Compressive strength values of concrete samples with partial replacement of cement with mechanochemically activated coal fly ash are given. The third and forth part is aimed to utilization of recycled concrete and steel slag as a natural aggregate replacement in concrete mixture for purpose of structural concrete and surface roads.

scholarly journals Artificial Intelligence Approaches for Prediction of Compressive Strength of Geopolymer Concrete

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 983 ◽  
Author(s):  
Dong Dao ◽  
Hai-Bang Ly ◽  
Son Trinh ◽  
Tien-Thinh Le ◽  
Binh Pham
Keyword(s):  
Artificial Intelligence ◽  
Compressive Strength ◽  
Fly Ash ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Steel Slag ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Partial Replacement ◽  
Geopolymer Concrete

Geopolymer concrete (GPC) has been used as a partial replacement of Portland cement concrete (PCC) in various construction applications. In this paper, two artificial intelligence approaches, namely adaptive neuro fuzzy inference (ANFIS) and artificial neural network (ANN), were used to predict the compressive strength of GPC, where coarse and fine waste steel slag were used as aggregates. The prepared mixtures contained fly ash, sodium hydroxide in solid state, sodium silicate solution, coarse and fine steel slag aggregates as well as water, in which four variables (fly ash, sodium hydroxide, sodium silicate solution, and water) were used as input parameters for modeling. A total number of 210 samples were prepared with target-specified compressive strength at standard age of 28 days of 25, 35, and 45 MPa. Such values were obtained and used as targets for the two AI prediction tools. Evaluation of the model’s performance was achieved via criteria such as mean absolute error (MAE), root mean square error (RMSE), and coefficient of determination (R2). The results showed that both ANN and ANFIS models have strong potential for predicting the compressive strength of GPC but ANFIS (MAE = 1.655 MPa, RMSE = 2.265 MPa, and R2 = 0.879) is better than ANN (MAE = 1.989 MPa, RMSE = 2.423 MPa, and R2 = 0.851). Sensitivity analysis was then carried out, and it was found that reducing one input parameter could only make a small change to the prediction performance.

Effect of steel slag powder, fly ash, and silica fume on the mechanical properties and durability of cement mortar

2019 ◽  
Vol 9 (9) ◽  
pp. 1049-1054
Author(s):  
Yunxia Lun ◽  
Fangfang Zheng
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Cement Mortar ◽  
Steel Slag ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Slag Powder ◽  
Steel Slag Powder

This study is aimed at exploring the effect of steel slag powder (SSP), fly ash (FA), and silica fume (SF) on the mechanical properties and durability of cement mortar. SSP, SF, and FA were used as partial replacement of the Ordinary Portland cement (OPC). It was showed that the compressive and bending strength of steel slag powder were slightly lower than that of OPC. An increase in the SSP content caused a decrease in strength. However, the growth rate of compressive strength of SSP2 (20% replacement by the weight of OPC) at the curing ages of 90 days was about 8% higher than that of OPC, and the durability of SSP2 was better than that of OPC. The combination of mineral admixtures improved the later strength, water impermeability, and sulfate resistance compared with OPC and SSP2. The compressive strength of SSPFA (SSP and SF) at 90 days reached 70.3 MPa. The results of X-ray diffraction patterns and scanning electron microscopy indicated that SSP played a synergistic role with FA or SF to improve the performance of cement mortar.

scholarly journals Production of ceramics from coal fly ash

2012 ◽  
Vol 18 (2) ◽  
pp. 245-254 ◽  
Author(s):  
Biljana Angjusheva ◽  
Emilija Fidancevska ◽  
Vojo Jovanov
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Solid State ◽  
Liquid Phase ◽  
Bending Strength ◽  
Coal Fly Ash ◽  
Liquid Phase Sintering ◽  
Heating Rates ◽  
Republic Of Macedonia ◽  
The Subject

Dense ceramics are produced from fly ash from REK Bitola, Republic of Macedonia. Four types of fly ash from electro filters and one from the collected zone with particles < 0.063 mm were the subject of this research. Consolidation was achieved by pressing (P= 133 MPa) and sintering (950, 1000, 1050 and 11000C and heating rates of 3 and 100/min). Densification was realized by liquid phase sintering and solid state reaction where diopside [Ca(Mg,Al)(Si,Al)2O6] was formed. Ceramics with optimal properties (porosity 2.96?0.5%, bending strength - 47.01?2 MPa, compressive strength - 170 ?5 MPa) was produced at 1100?C using the heating rate of 10?C/min.

An Investigation of Usability of Brown Coal Fly Ash for Building Materials

2013 ◽  
Vol 438-439 ◽  
pp. 30-35 ◽  
Author(s):  
Nirdosha Gamage ◽  
Sujeeva Setunge ◽  
Kasuni Liyanage
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Brown Coal ◽  
Water Contamination ◽  
Building Materials ◽  
Coal Fly Ash ◽  
Sustainable Building ◽  
Laboratory Investigations ◽  
Cold Pressed ◽  
Initial Results

The Victoria State of Australia has the second largest reserves of brown coal on earth, representing approximately 20% of the worlds reserves, and at current use, could supply Victoria with its energy for over 500 years. Its combustion, annually, yields up to 1.3 million tonnes of fly ash, which is largely use for land-fills. Disposal of fly ash in open dumps cause massive environmental problems such as ground water contamination that may create various health problems. This study focuses on the usability of brown coal fly ash to develop a sustainable building material. A series of laboratory investigations was conducted using brown coal fly ash combined with cement and aggregate to prepare cold pressed samples aiming to test their properties. Initial results indicate that compressive strength satisfies minimum standard compressive strength required for bricks or mortar.

The Effect of Substituting Rdf on the Physical and Environmental Properties of Coal Fly Ash

1988 ◽  
Vol 136 ◽  
Author(s):  
Ashaari B. Mohamad ◽  
David L. Gress
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Physical Properties ◽  
Activity Index ◽  
Coal Fly Ash ◽  
Pozzolanic Activity ◽  
Portland Cement Concrete ◽  
Fly Ash Concrete ◽  
Refuse Derived Fuel ◽  
Cadmium And Lead

ABSTRACTRefuse-derived-fuel (RDF) consisting mainly of waste paper and plastics is a viable fuel source for the production of power. An experimental test burn partially substituting coal with RDF was undertaken by the Public Service of New Hampshire at the Merrimack Power Station.Five percent and ten percent RDF were substituted, on a BTU basis, for coal in the test bums. The chemical and physical properties of the resulting fly ash were determined. Twelve test burn days were run with 4 days of 5% RDF and 8 days of 10% RDF. Emphasis was placed on investigating the effect of the RDF fly ash on Portland cement concrete.Most of the chemical and physical properties of the coal-RDF fly ash were found to be comparable with ordinary coal fly ash except for the amount of cadmium and lead, the pozzolanic activity index and the compressive strength of fly ash concrete. Cadmium and lead were at average levels of 5.1 ppm and 102.6 ppm for the 5% RDF, and 7.8 ppm and 198.3 ppm for the 10% RDF, respectively. Although the pozzolanic activity index of coal-RDF fly ash increases over normal coal fly ash, preliminary results show that the 28-day compressive strength of concrete with direct replacement of cement and sand decreases by up to 30%. Leaching tests on crushed concrete were conducted to evaluate the environmental effect of acid rain.

scholarly journals Utilization of Electroplating Sludge as Subgrade Backfill Materials: Mechanical and Environmental Risk Evaluation

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Yu Zhang ◽  
Peixin Shi ◽  
Lijuan Chen ◽  
Qiang Tang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Content ◽  
Environmental Risk ◽  
Coal Fly Ash ◽  
Surrounding Environment ◽  
Electroplating Sludge ◽  
Backfill Materials ◽  
Standard Limit ◽  
The Impact

The electroplating sludge may pose serious threat to human health and surrounding environment without safe treatment. This paper investigated the feasibility of using electroplating sludge as subgrade backfill materials, by evaluating the mechanical properties and environmental risk of the cement-coal fly ash solidified sludge. In this study, Portland cement and coal fly ash are used to solidify/stabilize the sludge. After curing for 7, 14, and 28 days, the stabilization/solidification sludge specimens were subject to a series of mechanical, leaching, and microcosmic tests. It was found that the compressive strength increased with the increase of cement content, curing time, and the cement replacement by coal fly ash besides water content. Among these factors, the impact of water content on the compressive strength is most noticeable. It was observed that the compressive strength declined by 87.1% when the water content increased from 0% to 10%. Besides, leaching tests showed that the amount of leaching heavy metals were under the standard limit. These results demonstrated utilization of electroplating sludge in subgrade backfill material may provide an alternative for the treatment of electroplating sludge.

scholarly journals Effect of Fly Ash on the Compressive Strength of Green Concrete

2020 ◽  
Vol 10 (3) ◽  
pp. 5728-5731 ◽  
Author(s):  
S. A. Chandio ◽  
B. A. Memon ◽  
M. Oad ◽  
F. A. Chandio ◽  
M. U. Memon
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Recycled Aggregates ◽  
Waste Materials ◽  
Partial Replacement ◽  
Equal Proportion ◽  
Standard Size ◽  
Green Concrete ◽  
Coarse Aggregates ◽  
Management Issues

This research paper aims at investigating the effects of fly ash as cement replacement in green concrete made with partial replacement of conventional coarse aggregates with coarse aggregates from demolishing waste. Green concrete developed with waste materials is an active area of research as it helps in reducing the waste management issues and protecting the environment. Six concrete mixes were prepared using 1:2:4 ratio and demolishing waste was used in equal proportion with conventional aggregates, whereas fly ash was used from 0%-10% with an increment of 2.5%. The water-cement ratio used was equal to 0.5. Out of these mixes, one mix was prepared with all conventional aggregates and was used as the control, and one mix with 0% fly ash had only conventional and recycled aggregates. The slump test of all mixes was determined. A total of 18 cylinders of standard size were prepared and cured for 28 days. After curing the compressive strength of the specimens was evaluated under gradually increasing load until failure. It is observed that 5% replacement of cement with fly ash and 50% recycled aggregates gives better results. With this level of dosage of two waste materials, the reduction in compressive strength is about 11%.

scholarly journals Influence of Partial Replacement of Micro-Silica by Fly-Ash on Strength Properties of Reactive Powder Concrete

2020 ◽  
Vol 9 (3) ◽  
pp. 2932-2937
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Performance ◽  
Cementitious Materials ◽  
Partial Replacement ◽  
Reactive Powder Concrete ◽  
Experimental Investigations ◽  
Reactive Powder ◽  
Micro Silica

Reactive powder concrete (RPC) is the ultra-high strength concrete made by cementitious materials like silica fumes, cement etc. The coarse aggregates are completely replaced by quartz sand. Steel fibers which are optional are added to enhance the ductility. Market survey has shown that micro-silica is not so easily available and relatively costly. Therefore an attempt is made to experimentally investigate the reduction of micro-silica content by replacing it with fly-ash and mechanical properties of modified RPC are investigated. Experimental investigations show that compressive strength decreases gradually with addition of the fly ash. With 10 per cent replacement of micro silica, the flexural and tensile strength showed 40 and 46 per cent increase in the respective strength, though the decrease in the compressive strength was observed to be about 20 per cent. For further percentage of replacement, there was substantial drop in compressive, flexural as well as tensile strength. The experimental results thereby indicates that utilisation of fly-ash as a partial replacement to micro silica up to 10 per cent in RPC is feasible and shows quite acceptable mechanical performance with the advantage of utilisation of fly-ash in replacement of micro-silica.

Quaternary blended cement mortars containing wood ash, glass and slag powders

2021 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Marwa Saadi Mhmood
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Glass Powder ◽  
Steel Slag ◽  
Wood Ash ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Slag Powder ◽  
Steel Slag Powder

AbstractA quaternary supplementary cementitious materials as partial replacement of ordinary Portland cement decreases CO2 emission. This paper has investigated the properties of mortars made from different quaternary blends of wood ash, steel slag powder and glass powder with ordinary Portland cement at different replacement levels of 0, 24, 25, and 30% by weight of the binder. The blended mortar mixtures tested for flow, compressive strength and density. The results showed that the flow of mortars is decreased with the combined use of steel slag powder, glass powder, and wood ash compared with control mix. Compressive strength reduced with the combination of steel slag powder, glass powder and wood ash but this reduction effects is acceptable especially at 24% replacement contain super-plasticizer compared with the ecological benefit.

Sign in / Sign up

Export Citation Format

Share Document