Effect of Bentonite and Zinc Borate (ZB) Addition on Recycled Polypropylene Composites against Tensile and Burning Rate Properties

2015 ◽  
Vol 1105 ◽  
pp. 56-61 ◽  
Author(s):  
Neng Sri Suharty ◽  
Hanafi Ismail ◽  
Fajar Rakhman Wibowo ◽  
Desi Suci Handayani ◽  
Maulidan Firdaus ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Burning Rate ◽  
Fire Retardant ◽  
Zinc Borate ◽  
Test Results ◽  
Natural Fire ◽  
Polypropylene Composites ◽  
Recycled Polypropylene ◽  
Fuel Resistance

Has successfully created an optimum composite of rPP/DVB/PP-AA/comBen+ZB based on the mechanical and fuel resistance properties. The starting material recycled PP (rPP), PP modified acrylic acid (AA) as coupling agent (PP-AA), crosslinker divinylbenzene (DVB), 20 phr of commercial bentonite (comBen) and 5 phr of zinc borate (ZB), was reactivelly processed in xylene. Composites analysis using XRD presented that the bentonite had been exfoliated inside of PP matrix. Test results showed that both of tensile strength (TS) and young's modulus (YM) of rPP/DVB/PP-AA/comBen+ZB composites following ASTM D638 was increased. The testing results of burning rate (BR) of composite rPP/DVB/PP-AA/comBen+ZB according to ASTM D635 decreased. The presence of bentonite as a natural fire retardant and ZB as fire retardant additive on composite rPP/DVB/PP-AA/comBen+ZB able to increase mechanical properties and also improving the flammability resistance.

Improvement of Inflammability and Biodegradability of Bio-Composites Using Recycled Polypropylene with Kenaf Fiber Containing Mixture Fire Retardant

2014 ◽  
Vol 950 ◽  
pp. 18-23 ◽  
Author(s):  
Neng Sri Suharty ◽  
Hanafi Ismail ◽  
Kuncoro Dihardjo ◽  
Muhammad Nizam ◽  
Maulidan Firdaus
Keyword(s):  
Weight Loss ◽  
Tensile Strength ◽  
Mechanical Strength ◽  
Boric Acid ◽  
Burning Rate ◽  
Magnesium Hydroxide ◽  
Fire Retardant ◽  
Kenaf Fiber ◽  
Recycled Polypropylene ◽  
Fuel Resistance

Have been reactively synthesized bio-composites material that has a good in mechanical strength and fuel resistance. The starting material for the manufacture of bio-composite was recycled PP (rPP) modified AA, reinforcement kenaf fiber (KF), the mixture of magnesium hydroxide (MH) and aluminum hydroxide (ATH) without or with boric acid (BA) as a fire retardant. The burning rate (BR) and tensile strength (TS) test were used ASTM D635 and D638, respectively. The presence of mixture fire retardant [MH/ATH] with ratio of 15/5 in the bio-composites can effectively reduce their burning rate (BR). Biodegradability of the bio-composites, which is reflected by weight loss (WL) is achieved arise after burying the bio-composites in garbage soil for four months. However, the presence of mixture fire retardant could marginally decrease the TS of the bio-composites.

Preparation Techniques and Property Evaluations of Highly Air Permeable Needle-Punched Geotextiles

2015 ◽  
Vol 749 ◽  
pp. 278-281
Author(s):  
Jia Horng Lin ◽  
Jing Chzi Hsieh ◽  
Jin Mao Chen ◽  
Wen Hao Hsing ◽  
Hsueh Jen Tan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Service Life ◽  
Mechanical Strength ◽  
Pore Structure ◽  
Test Results ◽  
Needle Punching ◽  
Pet Fibers ◽  
Environmental Requirements ◽  
Preparation Techniques

Geotextiles are made of polymers, and their conjunction with different processes and materials can provide geotextiles with desirable characteristics and functions, such as filtration, separation, and drainage, and thereby meets the environmental requirements. Chemical resistant and mechanical strong polymers, including polyester (PET) and polypropylene (PP), are thus used to prolong the service life of the products made by such materials. This study proposes highly air permeable geotextiles that are made with different thicknesses and various needle punching speeds, and the influences of these two variables over the pore structure and mechanical properties are then examined. PET fibers, PP fibers, and recycled Kevlar fibers are blended, followed by being needle punched with differing spaces and speeds to form geotextiles with various thicknesses and porosities. The textiles are then evaluated for their mechanical strength and porosity. The test results show that a thickness of 4.5 cm and 1.5 cm demonstrate an influence on the tensile strength of the geotextiles, which is ascribed to the webs that are incompletely needle punched. However, the excessive needle punching speed corresponding to a thickness of 0.2 cm results in a decrease in tensile strength, but there is also an increase in the porosity of the geotextiles.

scholarly journals The Influence of the Asymmetric Arb Process on the Properties of Al-Mg-Al Multi-Layer Sheets / Wpływ Asymetrii W Procesie Arb Na Właściwości Wielowarstwowych Blach Al-Mg-Al

2015 ◽  
Vol 60 (4) ◽  
pp. 2821-2826 ◽  
Author(s):  
A. Wierzba ◽  
S. Mróz ◽  
P. Szota ◽  
A. Stefanik ◽  
R. Mola
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Rolling Process ◽  
Asymmetry Factor ◽  
Relative Reduction ◽  
Test Results ◽  
Initial Thickness ◽  
Asymmetric Rolling ◽  
Aluminium Layer

The paper presents the results of the experimental study of the three-layer Al-Mg-Al sheets rolling process by the ARB method. The tests carried out were limited to single-pass symmetric and asymmetric rolling processes. An Al-Mg-Al package with an initial thickness of 4 mm (1-2-1 mm) was subjected to the process of rolling with a relative reduction of 50%. To activate the shear band in the strip being deformed, an asymmetry factor of av=2 was applied. From the test results, an increase in the tensile strength of the multi-layer Al-Mg-Al sheets obtained from the asymmetric process was observed. Microhardness tests did not show any significant differences in aluminium layer between respective layers of sheets obtained from the symmetric and the asymmetric process. By contrast, for the magnesium layer, an increase in microhardness from 72 HV to 79 HV could be observed for the asymmetric rolling. The analysis of the produced Al-Mg-Al sheets shows that the good bond between individual layers and grain refinement in the magnesium layer contributed to the obtaining of higher mechanical properties in the multi-layer sheets produced in the asymmetric process compared to the sheets obtained from the symmetric process.

Size Effect on Mechanical Properties of LVL

2014 ◽  
Vol 887-888 ◽  
pp. 824-829
Author(s):  
Qing Fang Lv ◽  
Ji Hong Qin ◽  
Ran Zhu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Size Effect ◽  
Tensile Test ◽  
Compression Test ◽  
Test Results ◽  
Laminated Veneer Lumber ◽  
Object Of Study ◽  
The Relationship

Laminated veneer lumber is taken as an object of study, and use LVL specimens of different sizes for compression test and tensile test. The goal of the experiment is to investigate the size effect on compressive strength and tensile strength as well as the influence of the secondary glued laminated face, which appears in the secondary molding processes. The results show that both compressive strength and tensile strength have the size effect apparently and the existence of the secondary glued laminated face lower the compressive strength of LVL specimens. Afterwards, the relationship between compressive strength and volume along with tensile strength and area are obtained by the test results.

scholarly journals Characteristics of Recycled Polypropylene Fibers as an Addition to Concrete Fabrication Based on Portland Cement

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1827 ◽  
Author(s):  
Marcin Małek ◽  
Mateusz Jackowski ◽  
Waldemar Łasica ◽  
Marta Kadela
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Concrete ◽  
Polypropylene Fibers ◽  
Split Tensile Strength ◽  
Recycled Polypropylene ◽  
Recycled Fibers

High-performance concrete has low tensile strength and brittle failure. In order to improve these properties of unreinforced concrete, the effects of adding recycled polypropylene fibers on the mechanical properties of concrete were investigated. The polypropylene fibers used were made from recycled plastic packaging for environmental reasons (long degradation time). The compressive, flexural and split tensile strengths after 1, 7, 14 and 28 days were tested. Moreover, the initial and final binding times were determined. This experimental work has included three different contents (0.5, 1.0 and 1.5 wt.% of cement) for two types of recycled polypropylene fibers. The addition of fibers improves the properties of concrete. The highest values of mechanical properties were obtained for concrete with 1.0% of polypropylene fibers for each type of fiber. The obtained effect of an increase in mechanical properties with the addition of recycled fibers compared to unreinforced concrete is unexpected and unparalleled for polypropylene fiber-reinforced concrete (69.7% and 39.4% increase in compressive strength for green polypropylene fiber (PPG) and white polypropylene fiber (PPW) respectively, 276.0% and 162.4% increase in flexural strength for PPG and PPW respectively, and 269.4% and 254.2% increase in split tensile strength for PPG and PPW respectively).

Influence of Stirring Time and Holding Time on Microstructure and Properties of the A356 Alloy Modified by Sc

2013 ◽  
Vol 750-752 ◽  
pp. 687-690 ◽  
Author(s):  
Su Zhang ◽  
Gang Yang ◽  
Jian Hong Yi ◽  
Hong Yan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Grain Boundary ◽  
Eutectic Silicon ◽  
A356 Alloy ◽  
Holding Time ◽  
Test Results ◽  
Modification Effect ◽  
Microstructure And Mechanical Properties ◽  
Stirring Time

Effects of the holding time and the stirring time on the microstructure and mechanical properties of A356 alloy modified by Sc are researched. According to the test results, most of the eutectic silicon phases have changed to the shape of creeping point, dispersed in the grain boundary of α (Al) phase while stirring 1 minute, in which case both the tensile strength and elongation reach the highest, resulting in the best modification effect. The results also indicate that microstructure and mechanical properties of the alloy reach are the best modification effect when the melt is held 15 minute. It can be known that the optimal stirring time is 1 minute and the optimal holding time is 15 minute in the experiment condition of the work.

Enhancement of mechanical properties of composites made of calcium carbonate modified bamboo fibers and polypropylene

Holzforschung ◽  
2015 ◽  
Vol 69 (2) ◽  
pp. 215-221 ◽  
Author(s):  
Haitao Cheng ◽  
Jie Gao ◽  
Ge Wang ◽  
Sheldon Q. Shi ◽  
Shuangbao Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Tensile Strength ◽  
Tensile Modulus ◽  
Inorganic Materials ◽  
Polypropylene Composites ◽  
Fiber Treatment ◽  
Bamboo Fibers ◽  
Properties Of Composites

Abstract The work aimed at the improvement of the mechanical properties of bamboo fiber-polypropylene composites (BaFPPC) by treatment of the fibers with CaCO3 at various concentrations of the solution (0.05, 0.1, 0.2, and 0.3 mol l-1). CaCO3 particles were successfully deposited in situ to bamboo fibers by means of ionic reaction of Na2 CO3 and CaCl2 aqueous solution at various temperatures. Then BaFPPC were produced, and various tests on single fibers and the composites were performed. The compatibility between BaF and PP matrix was improved by the treatments. The crystallinity of inorganic materials was significantly affected by the reagent’s concentration. A 10.4% increase in tensile strength and a 16.7% increase in tensile modulus were observed after fiber treatment with CaCO3 at a concentration of 0.2 mol l-1.

The Effect of Polypropylene Fiber on the Mechanical Properties of Self-Compacting Concrete

2010 ◽  
Vol 168-170 ◽  
pp. 1325-1329
Author(s):  
Ye Ran Zhu ◽  
Jun Cai ◽  
Dong Wang ◽  
Guo Hong Huang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Polypropylene Fiber ◽  
Flexural Properties ◽  
Test Results ◽  
Self Compacting Concrete ◽  
Bending Tests ◽  
Flexural Toughness ◽  
Four Point Bending

This paper investigates the mechanical properties (compressive strength, splitting tensile strength and flexural toughness) of polypropylene fiber reinforced self-compacting concrete (PFRSCC). The effect of the incorporation of polypropylene fiber on the mechanical properties of PFRSCC is determined. Four point bending tests on beam specimens were performed to evaluate the flexural properties of PFRSCC. Test results indicate that flexural toughness and ductility are remarkably improved by the addition of polypropylene fiber.

Use of Cellulose-Containing Fillers in Composites with Polypropylene

1970 ◽  
Vol 17 (2) ◽  
pp. 150-154
Author(s):  
Marianna LAKA ◽  
Svetlana CHERNYAVSKAYA ◽  
Galia SHULGA ◽  
Viktor SHAPOVALOV ◽  
Andrej VALENKOV ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Shear Modulus ◽  
Rapeseed Oil ◽  
Water Retention ◽  
Raw Materials ◽  
Water Retention Value ◽  
Water Vapour Sorption ◽  
Recycled Polypropylene ◽  
Sulphate Pulp

The composites, containing recycled polypropylene and fillers, obtained from different lignocellulosics by the thermocatalytic destruction method, were investigated. Birch sawdust, newsprint wastes, cotton residues and wood bleached sulphate pulp were used as raw materials for obtaining fillers. The indices of mechanical properties (tensile strength, modulus of elasticity, deformation at break, shear modulus, toughness, twisting moment) of the composites' samples were determined. It has been found that the obtained composites have relatively good mechanical properties. Better results were obtained, using fillers from sawdust and wood pulp. After treating the fillers with rapeseed oil, their water vapour sorption and water retention value (WRV) decreased. In this case, the strength of the composites was higher.http://dx.doi.org/10.5755/j01.ms.17.2.484

Sign in / Sign up

Export Citation Format

Share Document