Research on Polypropylene Fiber and Mineral Admixtures on Fluidity of Cement-Based Materials

2011 ◽  
Vol 328-330 ◽  
pp. 1301-1304
Author(s):  
Xue Fei Li ◽  
Tao Guo
Keyword(s):  
Fly Ash ◽  
Cement Mortar ◽  
Polypropylene Fiber ◽  
Maximum Flow ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Polypropylene Fibers ◽  
Intensity Level ◽  
Reticular Fibers ◽  
Cement Based Materials

The purpose of this paper is based on the cement-based materials by adding fibers and mineral admixtures for composite, to cement the improvement of liquidity. Experiment with the intensity level of 42.5 ordinary portland cement, by adding polypropylene fibers, slag and fly ash cement mortar as a mineral admixture, the production of cement mortar matrix for the test, were conducted on a variety of mix Fluidity test. Experiments show that the addition of polypropylene fiber is not conducive to the mobility of mortar, especially monofilament fiber was more obvious than the reticular fibers. To join the slag, fly ash, mortar fluidity increased, indicating that slag and fly ash added to improve the workability of cement-based materials. When the fiber content reaches the maximum degree of maximum flow, indicating that slag, fly ash and polypropylene fibers will increase the combined effect of fluidity value. This innovation is obtained by adding fiber cement-based materials for toughening effect, with the use of mineral admixture can improve the overall performance of cement based materials, with further research and promotion value.

Finite Element Analysis of Dry Shrinkage of Fiber Cement Mortar

2014 ◽  
Vol 590 ◽  
pp. 312-315
Author(s):  
Wei Hong Xuan ◽  
Pan Xiu Wang ◽  
Yu Zhi Chen ◽  
Xiao Hong Chen
Keyword(s):  
Fracture Toughness ◽  
Cement Mortar ◽  
Polypropylene Fiber ◽  
Polypropylene Fibers ◽  
Test Results ◽  
Ansys Software ◽  
Element Analysis ◽  
Cement Based Materials ◽  
Dry Shrinkage ◽  
Good Agreement

The dry shrinkage deformation of polypropylene fiber mortar was analyzed by ANSYS software and compared with experiment value in this paper. The error of the calculated and experimental results in the 14 days and 28 days are 7.8% and 10.5%. It can be found that the calculated results are in good agreement with test results. The results indicate that the dry shrinkage value of polypropylene fiber mortar is lower than ordinary mortar. Adding polypropylene fibers can inhibit the process of cracking and improve the fracture toughness of cement-based materials.

scholarly journals Influence of Inertia and Low Active Mineral Admixture on Strength and Microstructure of Cement-Based Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-9
Author(s):  
Meijuan Rao ◽  
Wan Tang ◽  
Wei Zhou ◽  
Yaning Kong ◽  
Shuhua Liu
Keyword(s):  
Fly Ash ◽  
Early Stage ◽  
Heat Of Hydration ◽  
Mineral Admixture ◽  
Limestone Powder ◽  
Mineral Admixtures ◽  
Inert Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cement Based Materials

Cement-based materials were investigated by comparing the strength and microstructure of pastes and mortar containing limestone powder or low quality fly ash. The compressive strength of the mortar at 28 and 90 d was examined whose microstructures were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis, and differential thermal analysis (TG-DTA). The results indicated that the strength of mortar decreased with increasing mineral admixtures. The limestone powder mainly acted as inert filler and hardly took part in the chemical reaction. Low quality fly ash may accelerate the formation of hydration products in samples with more chemically bonded water. This further resulted in a higher degree of cement hydration and denser microstructure, while the overall heat of hydration was reduced. At the early stage of hydration, low quality fly ash can be considered as an inert material whereas its reactivity at the later stage became high, especially for ground low quality fly ash.

Effects of Fly Ash and Granular Blast-Furnace Slag on Development Rate of Strength of Concrete

2014 ◽  
Vol 629-630 ◽  
pp. 371-375
Author(s):  
Ji Wei Cai ◽  
Si Jia Yan ◽  
Gong Lei Wei ◽  
Lu Wang ◽  
Jin Jin Zhou
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Development Rate ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Conventional Concrete ◽  
Enhancing Effect ◽  
Substitution Content ◽  
Furnace Slag

Fly ash (FA) and granular blast-furnace slag (GBFS) are usual mineral admixtures to conventional concrete, and their contents substituted for Portland cement definitely affect development rate of strength of concrete. C30 and C60 concrete samples with FA and/or GBFS were prepared to study the influence of substitution content of the mineral admixtures on 3 d, 7 d and 28 d strength. The results reveal that the development rate of strength in period from 3 d to 7 d gets slow with increasing content of mineral admixtures except for concrete with only GBFS less than 20%. In the case of substituting FA as the only mineral admixture for part of cement, the development rate of strength of C30 concrete in period from 7 d to 28 d keeps roughly constant even that of C60 concrete increases. When substituting mineral admixtures in the presence of GBFS for cement within experimental range, the development rate of strength in period from 7 d to 28 d gets fast with increasing substitution content. The enhancing effect of combining FA and GBFS occurs in period from 7 d to 28 d for both C30 and C60 concretes (FA+GBFS≤40%), even occurs in period from 3 d to 7 d for C60 concrete. Based on 7 d strength and the development rate, 28 d strength of concrete can be predicted accurately.

scholarly journals Mechanical Properties and Microscopic Mechanism of Coral Sand-Cement Mortar

2020 ◽  
Vol 2020 ◽  
pp. 1-11 ◽  
Author(s):  
Luoxin Wang ◽  
Junshuai Mei ◽  
Jing Wu ◽  
Xingyang He ◽  
Hainan Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cement Mortar ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Hardened Cement ◽  
Hydration Reaction ◽  
Microscopic Mechanism ◽  
X Ray ◽  
Volume Stability ◽  
Coral Sand

The workability and mechanical performance of coral sand-cement mortar (coral mortar, for short) and the modification effects of mineral admixtures on the coral mortar were studied in this paper. The results showed that the strength of coral mortar was lower than that of standard mortar, but the strength of coral mortar was improved by compositing with the mineral admixture, which can be attributed to the improvement of the microstructure and interface transition area. Scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR) were used to explore the microscopic mechanism involved in the mechanical properties, volume stability, and hydration of mortar. The analyses revealed that the internal curing effect of coral sand improved the mechanical properties of mortar and its ability to resist shrinkage. The uneven surface of coral sand formed a meshing state of close combination with the hardened cement mortar, which helped to improve the volume stability of mortar. The Ca2+ and Mg2+ ions from coral sand participated in the hydration reaction of cement, which contributed to generating more hydration products. Moreover, the microaggregate filling and pozzolanic effects of fly ash and slag improved the mechanical properties of coral mortar and resistance to chloride ion diffusion.

Study on the Durability of Concrete with Mineral Admixtures to Sulfate Attack by Wet-Dry Cycle Method

2011 ◽  
Vol 295-297 ◽  
pp. 165-169
Author(s):  
Guan Guo Liu ◽  
Jing Ming ◽  
Xiong Wen Zhang ◽  
Ai Bin Ma
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Sulfate Attack ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Change Environment ◽  
Physical Mechanisms ◽  
Chemical Attack ◽  
Tidal Area

Sulfate attack is one of several chemical and physical mechanisms of concrete deterioration. In actual situation, concrete structures always suffer from the coupled effects of multifactor such as wet-dry cycle and sulfate attack when exposed to tidal area or groundwater level change environment. Partial replacement of cement with mineral admixture is one of the efficient methods for improving concrete resistance against sulfate attack. In this regard, the resistance of concrete with fly ash and slag to sulfate attack was investigated by wet-dry cycle method. The degree of sulfate attack on specimens after different cycles was observed using scanning electron microscopy. The results of compressive strength and percentage of compressive strength evolution factor at various cycling times show an increase in the sulfate resistance of concrete with 60% of fly ash and slag than that only with 40% fly ash. The microstructural study indicates that the primary cause of deterioration of concrete under wet-dry cycle condition is swelling of the sulfate crystal rather chemical attack.

scholarly journals Effects of Expansive Agents on the Early Hydration Kinetics of Cementitious Binders

Materials ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 1900 ◽  
Author(s):  
Miao Miao ◽  
Qingyang Liu ◽  
Jian Zhou ◽  
Jingjing Feng
Keyword(s):  
Fly Ash ◽  
Hydration Heat ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Hydration Reaction ◽  
Hydration Kinetics ◽  
Early Hydration ◽  
Expansive Agent ◽  
Mechanical Performances ◽  
Kinetics Of

The addition of expansive agents could overcome the main disadvantages of raw concrete including high brittleness and low tensile strength. Few studies have investigated the early hydration kinetics of expansive cementitious binders, though the findings from the early hydration kinetics are helpful for understanding their technical performances. In this study, mixtures of 3CaO•3Al2O3•CaSO4 and CaSO4 (i.e., ZY-type™ expansive agent) with different proportions of mineral admixtures (e.g., fly ash and slag) were added into cement pastes to investigate the early hydration kinetics mechanism of expansive cementitious binders. Early hydration heat evolution rate and cumulative hydration heat were measured by isothermal calorimeter. Kinetic parameters were estimated based on the Krstulovic–Dabic model and Knudsen equations. Mechanical performances of expansive cementitious binders were tested in order to evaluate if they met the basic requirements of shrinkage-compensating materials in technical use. The early hydration heat released from cementitious binders containing ZY-type™ expansive agent was much greater than that released by pure cement, supporting the idea that addition of the expansive agent would improve the reaction of cement. The early hydration kinetic rates were decreased due to the reactions of the mineral admixture (e.g., fly ash or slag) and the ZY-type™ expansive agent in the cement system. The hydration reaction of cementitious binders containing ZY-type™ expansive agent obeyed the Krstulovic–Dabic model well. Three processes are involved in the hydration reaction of cementitious binders containing ZY-type™ expansive agent. These are nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The 14-day expansion rates of cementitious binders containing ZY-type™ expansive agent are in the range of 2.0 × 10−4 to 3.5 × 10−4, which could meet the basic requirements of anti-cracking performances in technical use according to Chinese industry standard JGJ/T 178-2009. This study could provide an insight into understanding the effects of expansive agents on the hydration and mechanical performances of cementitious binders.

Evaluation of Fresh Properties and Rheology of Mortar Using Carbon-Free Fly Ash and Normal Fly Ash

2020 ◽  
Vol 1005 ◽  
pp. 76-81
Author(s):  
Ghawsaddin Nazari ◽  
Shunya Yamanaka ◽  
Shigeyuki Date
Keyword(s):  
Fly Ash ◽  
Setting Time ◽  
Great Influence ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Fresh Properties ◽  
Initial Setting Time ◽  
Usual Solution ◽  
Initial Setting ◽  
Flow Loss

Usage of mineral admixture and chemical admixture in concrete or mortar is a usual solution to reach full compaction, particularly where reinforcement blockage and lack of skilled labor happen. In this paper effect of mineral admixtures (Carbon-free fly ash, hereafter CfFA, and normal fly ash) on fresh properties and rheology of mortar have been investigated. As a result, it was confirmed that CfFA increased significantly the fluidity and air content of mortar in comparison to normal fly ash, both in 15% and 30% replacement; however, the flow loss and air stability within one hour were almost equal. In addition, the initial setting time has also been affected by variation of materials. The two mixing of 30% and 15% of CfFA had a shorter setting time in comparison to the mortar with normal fly ash. Furthermore, CfFA based mortar had a great influence on rheology of mortar. Compared to normal fly ash, CfFA Considerably decreased the plastic Viscosity and increased the productivity of the mortar, both in non-vibrated and vibrated condition, particularly those with 30% replacement.

Experimental Study on the Anti-Cracking Property of Basalt Fiber for Cement-Based Materials

2011 ◽  
Vol 328-330 ◽  
pp. 1351-1354
Author(s):  
Jun Yong He ◽  
Xiao Qing Huang ◽  
Cheng Yu Tian
Keyword(s):  
Experimental Study ◽  
Experimental Research ◽  
21St Century ◽  
Cement Mortar ◽  
Polypropylene Fiber ◽  
Basalt Fiber ◽  
Polyacrylonitrile Fiber ◽  
Plastic Shrinkage ◽  
The World ◽  
Cement Based Materials

Basalt fiber has the advantages of non-pollution and omnipotence, and will be widely used in the 21st Century. Therefore, more and more attention is paid on experimental research on the basalt fiber in the world. First,according to the requirements of the fibers used in the cement-based materials, the contrast testing of the plastic shrinkage between fiber cement mortar and pure mortar was made. The experimental results showed that basalt fiber , polypropylene fiber and polyacrylonitrile fiber can be preliminarily chosen as reinforced fibers in cement-based materials. Finally, taking both characteristics of basalt fiber and the increase of cement-based materials costs into account, it can be drawn that top priority should be given to the basalt fiber rather than to other fibers for cement-based materials.

A Research on the Anti-Sulfate Corrosion Effects of the Concrete Mixed with Complex Multi-Mineral Admixture

2011 ◽  
Vol 71-78 ◽  
pp. 755-759
Author(s):  
Ying Tang ◽  
Guo An Wang
Keyword(s):  
Fly Ash ◽  
Silica Fume ◽  
Significant Influence ◽  
Ash Content ◽  
Performance Characteristics ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Corrosion Effect ◽  
Slag Content

This paper is focused on the method for improving capability of anti-sulfate corrosion of concrete. Based on the performance characteristics of mineral admixture, propose a method that mixing concrete with complex multi-mineral admixture to improve the effect of anti-sulfate corrosion. Finally, the ability of anti-sulfate corrosion and anti-dry-wet cycle, in different case, is studied and compared. The results show that concrete mixed with complex multi-mineral admixture is advantageous to improve the anti-sulfate corrosion effects of the concrete. The proportion of mineral admixtures has significant influence on the anti-sulfate corrosion effect. As the silica fume and slag content increased, the fly ash content decreased, the ability of anti-sulfate corrosion enhanced.

Effect of steel slag powder, fly ash, and silica fume on the mechanical properties and durability of cement mortar

2019 ◽  
Vol 9 (9) ◽  
pp. 1049-1054
Author(s):  
Yunxia Lun ◽  
Fangfang Zheng
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Cement Mortar ◽  
Steel Slag ◽  
Mineral Admixtures ◽  
Partial Replacement ◽  
Slag Powder ◽  
Steel Slag Powder

This study is aimed at exploring the effect of steel slag powder (SSP), fly ash (FA), and silica fume (SF) on the mechanical properties and durability of cement mortar. SSP, SF, and FA were used as partial replacement of the Ordinary Portland cement (OPC). It was showed that the compressive and bending strength of steel slag powder were slightly lower than that of OPC. An increase in the SSP content caused a decrease in strength. However, the growth rate of compressive strength of SSP2 (20% replacement by the weight of OPC) at the curing ages of 90 days was about 8% higher than that of OPC, and the durability of SSP2 was better than that of OPC. The combination of mineral admixtures improved the later strength, water impermeability, and sulfate resistance compared with OPC and SSP2. The compressive strength of SSPFA (SSP and SF) at 90 days reached 70.3 MPa. The results of X-ray diffraction patterns and scanning electron microscopy indicated that SSP played a synergistic role with FA or SF to improve the performance of cement mortar.

Sign in / Sign up

Export Citation Format

Share Document