Corrosion Behavior of ZnAlMg Coating of Dual Phase Steel Sheet

2014 ◽  
Vol 881-883 ◽  
pp. 1275-1279
Author(s):  
Xiao Dong Hao ◽  
Qi Fu Zhang
Keyword(s):  
Corrosion Resistance ◽  
Rust Resistance ◽  
Steel Sheet ◽  
Dual Phase Steel ◽  
Salt Spray ◽  
Dual Phase ◽  
Neutral Salt ◽  
High Corrosion Resistance ◽  
Products Analysis ◽  
Resistance Performance

The effect of different composition ratio of ZnAlMg coatings on the corrosion resistance of dual phase steel sheet was experimental studied. The results of neutral salt spray test and corrosion products analysis showed that the three kinds of ZnAlMg coatings have different rust resistance performance. Both the Zn6Al3Mg and Zn13.5Al1.5Mg coatings have high corrosion resistance than the pure Zn coating. The Zn13.5Al1.5Mg coating has better anticorrosion performance than the Zn6Al3Mg coating.

USS DUAL PHASE 80

Alloy Digest ◽  
1978 ◽  
Vol 27 (12) ◽  
Keyword(s):  
United States ◽  
Corrosion Resistance ◽  
Yield Strength ◽  
Work Hardening ◽  
Steel Sheet ◽  
High Strength ◽  
Heat Treating ◽  
Dual Phase ◽  
United States Steel Corporation ◽  
Heavy Construction

Abstract USS Dual Phase 80 is a high-strength steel sheet which has a dual phase structure of martensite and ferrite. It provides all the benefits of higher strength with little sacrifice in ductility, formability or weldability. Dual Phase 80 gains strength as it is formed through rapid work hardening of its unique microstructure; in fact, it increases from its delivered yield strength of 50,000 psi up to 80,000 psi (or more) in forming. Its final strength depends on the amount of forming. Its many applications include automotive vehicles, farm equipment and heavy construction equipment. This datasheet provides information on composition, hardness, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SA-352. Producer or source: United States Steel Corporation.

scholarly journals Design and Multidimensional Screening of Flash-PEO Coatings for Mg in Comparison to Commercial Chromium(VI) Conversion Coating

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 337
Author(s):  
Ewa Wierzbicka ◽  
Marta Mohedano ◽  
Endzhe Matykina ◽  
Raul Arrabal
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Protection ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Conversion Coating ◽  
Neutral Salt ◽  
Chromium Vi ◽  
Alkaline Electrolytes ◽  
Az31b Alloy ◽  
Plasma Electrolytic

REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) regulations demand for an expedient discovery of a Cr(VI)-free alternative corrosion protection for light alloys even though the green alternatives might never be as cheap as current harmful technologies. In the present work, flash- plasma electrolytic oxidation coatings (FPEO) with the process duration < 90 s are developed on AZ31B alloy in varied mixtures of silicate-, phosphate-, aluminate-, and fluoride-based alkaline electrolytes implementing current density and voltage limits. The overall evaluation of the coatings’ anticorrosion performance (electrochemical impedance spectroscopy (EIS), neutral salt spray test (NSST), paintability) shows that from nine optimized FPEO recipes, two (based on phosphate, fluoride, and aluminate or silicate mixtures) are found to be an adequate substitute for commercially used Cr(VI)-based conversion coating (CCC). The FPEO coatings with the best corrosion resistance consume a very low amount of energy (~1 kW h m−2 µm−1). It is also found that the lower the energy consumption of the FPEO process, the better the corrosion resistance of the resultant coating. The superb corrosion protection and a solid environmentally friendly outlook of PEO-based corrosion protection technology may facilitate the economic justification for industrial end-users of the current-consuming process as a replacement of the electroless CCC process.

Corrosion resistance and mechanical characteristics of dual-phase steel B500c, after shot blasting processes

2017 ◽  
Vol 8 (5) ◽  
pp. 544-564
Author(s):  
Argyro Drakakaki ◽  
Charis Apostolopoulos ◽  
Alexandros Katsaounis ◽  
Hasa Bjorn
Keyword(s):  
Corrosion Resistance ◽  
Chemical Composition ◽  
Dual Phase Steel ◽  
Structural Integrity ◽  
Positive Impact ◽  
Electrochemical Techniques ◽  
Dual Phase ◽  
Shot Blasting ◽  
Production Mode ◽  
Content Type

Purpose Corrosive agent constitutes a major problem for constructions located in coastal areas, since it keeps affecting their durability. This phenomenon, in synergy with moisture and high temperatures, leads to premature deterioration of the structures. Under these conditions, the need for management of the problem of resistance of steel against corrosion is an issue of paramount importance and a challenge to the structural integrity and reliability. The paper aims to discuss these issues. Design/methodology/approach The need for management of the problem of resistance of steel against corrosion is an issue of paramount importance and a challenge to the structural integrity and reliability. In the present study, an effort was made to increase the corrosion resistance of the high strength and ductility dual-phase steel B500c category, with the use of different shot blasting processes, without any interference in the chemical composition or in the production mode. In particular, shot blasting treatment was used for both cleaning and creating compressive stresses on the surface of steel bars, according to the pertinent protocols. The modified samples were studied via both conventional characterization methods and electrochemical techniques. Findings Through the whole surface treatment process of B500c steel, a positive impact came about not only the corrosion resistance, but also the mechanical performance. Originality/value Shot blasting process aims to increase the corrosion resistance of high ductility dual-phase steel (B500c), without any interference in the chemical composition or in the production mode.

scholarly journals Effect of Martensite Morphologies on Corrosion in 5% H2SO4 Solution of Borided X70 Dual Phase Steel

2021 ◽  
Vol 45 (1) ◽  
pp. 69-74
Author(s):  
Tassi Hocine ◽  
Zidelmel Sami ◽  
Allaoui Omar
Keyword(s):  
Corrosion Resistance ◽  
Dual Phase Steel ◽  
Annealing Temperature ◽  
Intercritical Annealing ◽  
Ferrite Matrix ◽  
Dual Phase ◽  
H2so4 Solution ◽  
Dp Steel ◽  
Direct Quenching ◽  
Step Quenching

In the present investigation, some electrochemical properties of dual phase X70 steels with different martensite morphologies which have undergone boriding were studied. To obtain a variety of martensite morphologies, Direct Quenching (DQ), Intermediate Quenching (IQ) and Step Quenching (SQ) heat treatments were applied at an intercritical annealing temperature (IAT) of 760℃. The treatment (DQ) allowed the formation of fine martensite evenly distributed in the ferrite matrix. (IQ) treatment showed the formation of martensite along the ferrite / ferrite grain boundaries. In contrast, treatment (SQ) induced the formation of a banded morphology of martensite and ferrite. The realization of borides on X70 (DP) steel was carried out in a powder mixture containing 5% of B4C as source of boron, 5% of NaBF4 as activator and 90% of SiC as diluent at 950℃ for a period of time from 4 h. The corrosion behavior of X70 (DP) steel has been explored by the Tafel extrapolation method in a 5 wt. % H2SO4 solution. The corrosion resistance of steel which has undergone boriding (BDP) is higher than that of steel which has not undergone it (DP).

Corrosion resistance of composite coating used for fastener protection

2019 ◽  
Vol 66 (5) ◽  
pp. 595-602
Author(s):  
Zhifeng Lin ◽  
Likun Xu ◽  
Xiangbo Li ◽  
Li Wang ◽  
Weimin Guo ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Composite Coating ◽  
Marine Environment ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Diffusion Method ◽  
Economic Losses ◽  
Neutral Salt ◽  
Content Type

Purpose The purpose of this paper is to examine the performance of a fastener composite coating system, sherardized (SD) coating/zinc-aluminum (ZA) coating whether it has good performance in marine environment. Design/methodology/approach In this paper, SD coating was fabricated on fastener surface by solid-diffusion method. ZA coating was fabricated by thermal sintering method. Corrosion behaviours of the composite coating were investigated with potentiodynamic polarization curves, open circuit potential and electrochemical impedance spectroscopy methods. Findings Neutral salt spray (NSS) and deep sea exposure tests revealed that the composite coating had excellent corrosion resistance. Polarization curve tests showed that corrosion current density of the sample with composite coating was significantly decreased, indicating an effective corrosion protection of the composite coating. OCP measurement of the sample in NaCl solution demonstrated that the composite coating had the best cathodic protection effect. The good corrosion resistance of the composite coating was obtained by the synergy of SD and ZA coating. Practical implications SD/ZA coating can be used in marine environment to prolong the life of carbon steel fastener. Social implications SD/ZA composite coating can reduce the risk and accident caused by failed fastener, avoid huge economic losses. Originality/value A new kind of composite coating was explored to protect the carbon steel fastener in marine environment. And the composite coating has the long-term anti-corrosion performance both in simulated and marine environment test.

scholarly journals Plastic and fracture behavior of a dual phase steel sheet under quasi-static and dynamic loadings

2020 ◽  
Vol 235 ◽  
pp. 107165 ◽  
Author(s):  
Valentin Davaze ◽  
Nicolas Vallino ◽  
Sylvia Feld-Payet ◽  
Bertrand Langrand ◽  
Jacques Besson
Keyword(s):  
Fracture Behavior ◽  
Steel Sheet ◽  
Dual Phase Steel ◽  
Dual Phase ◽  
Dynamic Loadings

Effect of Sol-Gel Film on the Corrosion Resistance of Low Carbon Steel Plate

2020 ◽  
Vol 984 ◽  
pp. 43-50
Author(s):  
Hua Yuan Zhang ◽  
Can Wang ◽  
Bing Xue ◽  
Jing Luo
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Steel Plate ◽  
Salt Spray ◽  
Sol Gel ◽  
Low Carbon Steel ◽  
Corrosion Current ◽  
Neutral Salt ◽  
Low Carbon ◽  
Gel Film

To improve the corrosion resistance on Q235 low carbon steel, in this paper, tetraethyl orthosilicate (TEOS), N-dodecyl trimethoxysilane and γ-(2,3-epoxypropoxy) propytrimethoxysilane (KH560) were used to make organic-inorganic hybrid sol-gel film. Cross cut test adhesion method, neutral salt spray test, electrochemical test and film protective efficiency were taken to value the corrosion resistance property. The corrosion topography was studied by optical microscope. In addition, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) curves and equivalent electric circuit fitting were used to analyze the corrosion mechanism. The cross cut adhesion of sol-gel film can reach 1 class and the protection class can attain 5 class after 72 hours neutral salt spray test. According to the potentiodynamic polarization curve analysis, the corrosion potential of sol-gel film coating sample after 0.5 hours immersion was -0.46 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.74×10-7 A·cm-2. The corrosion potential of bare Q235 low carbon steel plate after 0.5 hours immersion was -0.78 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.75×10-6 A·cm-2. The impedance value on 0.1 Hz (|Z|0.1Hz) (1.27×106 Ω·cm2) of sol-gel film coating sample was more than three orders of magnitude higher than the value of the low carbon steel plate. Even dipping in 3.5 wt. % NaCl for 72 hours, the |Z|0.1Hz value of sol-gel coating sample was still one order of magnitude higher than the low carbon steel plate with 0.5 hours immersion. Sol-gel film with excellent adhesion can significantly improve the corrosion resistance of low carbon steel plate. Sol-gel film can increase the protection efficiency of low carbon steel plate by 90%.

scholarly journals Impact of Bi and Sn on Microstructure and Corrosion Resistance of Zinc Coatings Obtained in Zn-AlNi Bath

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3788
Author(s):  
Henryk Kania ◽  
Mariola Saternus ◽  
Jan Kudláček
Keyword(s):  
Corrosion Resistance ◽  
Salt Spray ◽  
Neutral Salt ◽  
Energy Dispersion Spectroscopy ◽  
Humid Atmosphere ◽  
Alloying Additions ◽  
Electrochemical Parameters ◽  
Zinc Coatings ◽  
Structural Research ◽  
The Impact

The paper presents results of studies on the impact of bismuth and tin additions to the Zn-AlNi bath on microstructure and corrosion resistance of hot dip galvanizig coatings. The structure at high magnifications on the top surface and cross-section of coatings received in the Zn-AlNiBiSn bath was revealed and the microanalysis EDS (energy dispersion spectroscopy) of chemical composition was determined. The corrosion resistance of the coatings was tested relatively in a neutral salt spray test (NSS), and tests in a humid atmosphere containing SO2. Electrochemical parameters of coatings corrosion were determined. It was found that Zn-AlNiBiSn coatings show lower corrosion resistance in comparison with the coatings received in the Zn-AlNi bath without Sn and Bi alloying additions. Structural research has shown the existence of precipitations of Sn-Bi alloy in the coating. It was found that Sn-Bi precipitations have more electropositive potential in relation to zinc, which promotes the formation of additional corrosion cells.

The Influence of Major Defects on the Properties of Continuous Galvanized Steel Sheet

2012 ◽  
Vol 445 ◽  
pp. 661-666 ◽  
Author(s):  
A. Azimi ◽  
F. Shahriari ◽  
F. Ashrafizadeh ◽  
M.R. Toroghinezhad ◽  
J. Jamshidi
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Tensile Test ◽  
Steel Sheet ◽  
Corrosion Behaviour ◽  
Salt Spray ◽  
Galvanized Steel ◽  
Tafel Polarization ◽  
Steel Sheets ◽  
Bare Spot

Production of defect-free galvanized steel sheet is considered a major concern for automotive and other critical applications; nevertheless, the occurrence of some defects in the coated sheets is unavoidable. In order to alleviate the problem, we need to know the extent to which the properties of a galvanized sheet are influenced by the presence of a given defect. In this investigation, specimens including any of the two major defects of continuously galvanized steel sheets were selected from a large number of coated samples. The defects, including furnace roll pimples and bare spots, were microstructurally characterized and their influence on corrosion behaviour and mechanical properties of the steel sheet was evaluated. Corrosion resistance was examined via standard salt spray test and Tafel polarization. Tensile test was employed as a measure of mechanical properties of the defective galvanized sheets. The results indicated that the presence of defects had little influence on the tensile properties of the samples, but considerably reduced their corrosion resistance. Based on the results of salt spray tests, pimples reduced corrosion resistance of galvanized sheets 23 % (50 hours) on average and bare spot defects caused reduction in corrosion resistance up to 39%.

Sign in / Sign up

Export Citation Format

Share Document