Microstructure and Mechanical Properties of Laser Welded 316L SLM Parts

2020 ◽  
Vol 841 ◽  
pp. 306-311
Author(s):  
Timo Rautio ◽  
Jarmo Mäkikangas ◽  
Matias Jaskari ◽  
Markku Keskitalo ◽  
Antti Järvenpää
Keyword(s):  
Laser Welding ◽  
Weld Seam ◽  
Sheet Material ◽  
Base Material ◽  
Melting Process ◽  
Heat Treating ◽  
Joint Properties ◽  
Before And After ◽  
The Difference ◽  
Commercial Sheet

This paper focuses on a study conducted on laser welding of printed 316L parts that were produced with a selective laser melting process. Commercial sheet material was used as a reference for the printed 316L parts. The effect of heat treatment on joint properties, and on what stage of the process it should be applied, was studied with metallography and mechanical testing. Optical microscopy was applied to analyze the microstructure of the base material and the weld seam. Tensile testing was applied for determining monotonic strength of different structures. The printed base material showed higher strength, but lower ductility in comparison to the commercial sheet material. In the welded condition, tensile properties were impaired by the welding, but for the commercial sheet material, no clear effects were seen. The difference was hypothesized to be caused by the higher strength mismatch in the printed joints. For the welded structures, the best strength-ductility combination was achieved by heat treating the parts both before and after the laser welding.

Full Gas Burst Test for HFW Linepipe at Low Temperature

2014 ◽  
Author(s):  
Satoshi Igi ◽  
Satoru Yabumoto ◽  
Masaki Mitsuya ◽  
Yuya Sumikura ◽  
Mikihiro Takeuchi
Keyword(s):  
Residual Stress ◽  
Low Temperature ◽  
Fracture Behavior ◽  
Weld Seam ◽  
Base Material ◽  
Welding Process ◽  
Manufacturing Method ◽  
Burst Test ◽  
Drop Weight Tear Test ◽  
The Difference

A full gas burst test at low temperature below −40°C was performed using a high frequency welded (HFW) linepipe with high-quality weld seam, “MightySeam®,” [1–4] in order to verify the applicability of the Drop Weight Tear Test (DWTT). Residual stress exists in the pipe body of HFW linepipe because the manufacturing method includes a sizing process. Therefore, it is necessary to clarify the difference between the arrestability in the DWTT without residual stress in the specimen and that in the full gas burst test with residual stress in the pipe body. The full gas burst test is performed using a test pipe specimen in which a notch is introduced into the base material by an explosive cutter. In addition, a test pipe specimen with a notch introduced into the weld seam was used in this study because the developed HFW linepipe, “MightySeam®,” has excellent low-temperature toughness as a result of control of the morphology and distribution of oxides generated in the welding process by temperature and deformation distribution control. The Charpy transition temperature of “Mighty Seam®” was much lower than −45 °C. Ductile cracks were initiated from the initial explosive notch, and these cracks were arrested after ductile crack propagation of about 1 m in base material on both sides. The fracture behavior was similar in appearance in the DWTT without residual stress and the full gas burst test with residual stress.

Tem analysis of multiple-energy arsenic implanted and Rta'd silicon

1987 ◽  
Vol 45 ◽  
pp. 246-247
Author(s):  
R.A. Herring
Keyword(s):  
Device Fabrication ◽  
High Concentration ◽  
Tem Analysis ◽  
Defect Clusters ◽  
High Fluences ◽  
Small Defect ◽  
Before And After ◽  
The Matrix ◽  
The Difference ◽  
Factor Type

Rapid thermal annealing (RTA) of ion-implanted Si is important for device fabrication. The defect structures of 2.5, 4.0, and 6.0 MeV As-implanted silicon irradiated to fluences of 2E14, 4E14, and 6E14, respectively, have been analyzed by electron diffraction both before and after RTA at 1100°C for 10 seconds. At such high fluences and energies the implanted As ions change the Si from crystalline to amorphous. Three distinct amorphous regions emerge due to the three implantation energies used (Fig. 1). The amorphous regions are separated from each other by crystalline Si (marked L1, L2, and L3 in Fig. 1) which contains a high concentration of small defect clusters. The small defect clusters were similar to what had been determined earlier as being amorphous zones since their contrast was principally of the structure-factor type that arises due to the difference in extinction distance between the matrix and damage regions.

Changes in Platelet Aggregability after Ovariectomy

1979 ◽  
Vol 42 (04) ◽  
pp. 1332-1339 ◽  
Author(s):  
Hiroh Yamazaki ◽  
Takeshi Motomiya ◽  
Minoru Sonoda ◽  
Noboru Miyagawa
Keyword(s):  
Platelet Count ◽  
Platelet Activation ◽  
Ovarian Hormones ◽  
Control Group ◽  
Platelet Aggregability ◽  
Appearance Rate ◽  
Before And After ◽  
The Difference ◽  
Induced Aggregation ◽  
Observation Period

SummaryChanges in platelets in 48 patients with uterine myoma before and after hysterectomy with and without ovariectomy were examined. Bilateral ovariectomy in 25 cases (ovariec-tomized group) and unilateral or non-ovariectomy in 23 cases (control group) were performed at the hysterectomy. Platelet count and an appearance rate of secondary aggregation decreased at one day after and increased at one week after the operation, similarly in both the ovariectomized and the control group. The appearance rate of secondary aggregation was reflected in an intensity of aggregation at 5 min after the addition of reagent to PRP. At one month after the operation, the appearance rate of secondary aggregation induced by 3 μM ADP showed a statistically significant decrease in comparison with the preoperation value (P <0.05) and the enhancement of 5-min aggregation was still observed in the control group, while ceased in the ovariectomized group. The difference between the two groups was significant (P < 0.05). There was almost no change in the speed and intensity of primary and secondary aggregation during the observation period. No significant differences in collagen-induced aggregation were noted between the two groups. The results suggest that ovarian hormones, mainly estrogen, facilitate platelet activation which is mediated by the so-called secondary aggregation.

PENGARUH TERAPI TERTAWA TERHADAP PENURUNAN TEKANAN DARAH LANSIA DI UPT PANTI WREDHA BUDHI DHARMA YOGYAKARTA

2019 ◽  
Vol 13 (1) ◽  
Author(s):  
Niken Setyaningrum ◽  
Andri Setyorini ◽  
Fachruddin Tri Fitrianta
Keyword(s):  
Blood Pressure ◽  
Data Analysis ◽  
The Elderly ◽  
Control Group ◽  
Group Comparison ◽  
Control Blood Pressure ◽  
Men And Women ◽  
Treatment Of Hypertension ◽  
Before And After ◽  
The Difference

ABSTRACTBackground: Hypertension is one of the most common diseases, because this disease is suffered byboth men and women, as well as adults and young people. Treatment of hypertension does not onlyrely on medications from the doctor or regulate diet alone, but it is also important to make our bodyalways relaxed. Laughter can help to control blood pressure by reducing endocrine stress andcreating a relaxed condition to deal with relaxation.Objective: The general objective of the study was to determine the effect of laughter therapy ondecreasing elderly blood pressure in UPT Panti Wredha Budhi Dharma Yogyakarta.Methods: The design used in this study is a pre-experimental design study with one group pre-posttestresearch design where there is no control group (comparison). The population in this study wereelderly aged over> 60 years at 55 UPT Panti Wredha Budhi Dharma Yogyakarta. The method oftaking in this study uses total sampling. The sample in this study were 55 elderly. Data analysis wasused to determine the difference in blood pressure before and after laughing therapy with a ratio datascale that was using Pairs T-TestResult: There is an effect of laughing therapy on blood pressure in the elderly at UPT Panti WredhaBudhi Dharma Yogyakarta marked with a significant value of 0.000 (P <0.05)

Klein with Lacan: A Study on the Reception of Lacanian Ideas in Uruguay and Its Effects on Clinical Practices (1955–82)

2020 ◽  
Vol 22 (3) ◽  
pp. 341-361
Author(s):  
Gonzalo Grau-Pérez ◽  
J. Guillermo Milán
Keyword(s):  
Clinical Practice ◽  
Clinical Material ◽  
Clinical Practices ◽  
Before And After ◽  
The Difference ◽  
The 1960S ◽  
The Relationship ◽  
Discursive Approach ◽  
The Way ◽  
Clinical Cases

In Uruguay, Lacanian ideas arrived in the 1960s, into a context of Kleinian hegemony. Adopting a discursive approach, this study researched the initial reception of these ideas and its effects on clinical practices. We gathered a corpus of discursive data from clinical cases and theoretical-doctrinal articles (from the 1960s, 1970s and 1980s). In order to examine the effects of Lacanian ideas, we analysed the difference in the way of interpreting the clinical material before and after Lacan's reception. The results of this research illuminate some epistemological problems of psychoanalysis, especially the relationship between theory and clinical practice.

FRACTIONAL DETERMINATIONS OF URINARY 17-KETOSTEROIDS IN HYPEREMESIS GRAVIDARUM

1962 ◽  
Vol 41 (1) ◽  
pp. 123-128 ◽  
Author(s):  
Pentti A. Järvinen ◽  
Sykkö Pesonen ◽  
Pirkko Väänänen
Keyword(s):  
Hyperemesis Gravidarum ◽  
First Trimester ◽  
Control Group ◽  
Before And After ◽  
Daily Urine ◽  
First Trimester Of Pregnancy ◽  
The Difference

ABSTRACT The fractional determination of 17-ketosteroids in the daily urine was performed in nine cases of hyperemesis gravidarum and in four control cases, in the first trimester of pregnancy both before and after corticotrophin administration. The excretion of total 17-KS is similar in the two groups. Only in the hyperemesis group does the excretion of total 17-KS increase significantly after corticotrophin administration. The fractional determination reveals no difference between the two groups of patients with regard to the values of the fractions U (unidentified 17-KS), A (androsterone) and Rest (11-oxygenated 17-KS). The excretion of dehydroepiandrosterone is significantly higher in the hyperemesis group than in the control group. The excretion of androstanolone seems to be lower in the hyperemesis group than in the control group, but the difference is not statistically significant. The differences in the correlation between dehydroepiandrosterone and androstanolone in the two groups is significant. The high excretion of dehydroepiandrosterone and low excretion of androstanolone in cases of hyperemesis gravidarum is a sign of adrenal dysfunction.

Automatic Tread Gaging Machine

1979 ◽  
Vol 7 (1) ◽  
pp. 31-39
Author(s):  
G. S. Ludwig ◽  
F. C. Brenner
Keyword(s):  
Experimental Tests ◽  
Automatic Machine ◽  
Wear Rates ◽  
Handling Device ◽  
Straight Line ◽  
Component Systems ◽  
Before And After ◽  
Good Repeatability ◽  
The Difference ◽  
Straight Lines

Abstract An automatic tread gaging machine has been developed. It consists of three component systems: (1) a laser gaging head, (2) a tire handling device, and (3) a computer that controls the movement of the tire handling machine, processes the data, and computes the least-squares straight line from which a wear rate may be estimated. Experimental tests show that the machine has good repeatability. In comparisons with measurements obtained by a hand gage, the automatic machine gives smaller average groove depths. The difference before and after a period of wear for both methods of measurement are the same. Wear rates estimated from the slopes of straight lines fitted to both sets of data are not significantly different.

UNITEMP HX

Alloy Digest ◽  
1964 ◽  
Vol 13 (5) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Base Material ◽  
Heat Treating ◽  
Operating Conditions ◽  
High Temperature Strength ◽  
Temperature Performance ◽  
Nickel Base

Abstract Unitemp-HX is a nickel-base material recommended for high temperature applications. It has outstanding oxidation resistance at high temperatures under most operating conditions, and good high-temperature strength. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and creep. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Ni-91. Producer or source: Universal Cyclops Steel Corporation.

LESCALLOY 300M VAC ARC

Alloy Digest ◽  
1993 ◽  
Vol 42 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Tensile Strength ◽  
High Strength ◽  
Melting Process ◽  
Heat Treating ◽  
Pressure Vessels ◽  
Low Alloy Steel ◽  
Steel Company ◽  
High Hardenability ◽  
Ingot Structure

Abstract LESCALLOY 300M VAC ARC is a low-alloy steel with an excellent combination of high hardenability and high strength coupled with good ductility and good toughness. Its tensile strength ranges from 280,000 to 300,000 psi. It is produced by the vacuum consumable electrode melting process to provide optimum cleanliness and preferred ingot structure. Its applications include aircraft components, pressure vessels and fasteners. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on forming, heat treating, machining, joining, and surface treatment. Filing Code: SA-321. Producer or source: Latrobe Steel Company. Originally published March 1976, revised February 1993.

UGIMA 4404, UGIMA 316L

Alloy Digest ◽  
1998 ◽  
Vol 47 (12) ◽  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Melting Point ◽  
Physical Properties ◽  
Melting Process ◽  
Heat Treating ◽  
Aisi 316L

Abstract UGIMA 4404 (UGIMA 316L) is identical to UGINE 4404 (AISI 316L) in analysis, corrosion resistance, mechanical properties, and forging and welding ability, but not with respect to machinability. A specific melting process creates inclusions of malleable oxides with a low melting point. The inclusions improve machinability by 20-30% compared with AISI 316L (1.4404) stainless steel. This datasheet provides information on composition and physical properties. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: SS-735. Producer or source: Ugine-Savoie.

Sign in / Sign up

Export Citation Format

Share Document