Fungal Resistance of Polymeric Composite Materials Based on Polypropylene and Natural Rubber

2021 ◽  
Vol 899 ◽  
pp. 759-764
Author(s):  
Vladislav V. Yanov ◽  
Rishat R. Yusupov ◽  
Lyubov A. Zenitova
Keyword(s):  
Composite Materials ◽  
Natural Rubber ◽  
Penicillium Chrysogenum ◽  
Aspergillus Terreus ◽  
Polymeric Composite ◽  
Fungal Resistance ◽  
Average Weight ◽  
Paecilomyces Variotii ◽  
The Impact ◽  
Growth Of Fungi

Research has been carried out to assess the impact of mold fungi on polymer composite materials based on polypropylene produced by Omsk Polypropylene Plant LLC and unrefined natural rubber produced in Vietnam, grade RSS-1. The amount of natural rubber varied up to 15% of the mass. The fungal resistance of the compositions to the following types of fungi was assessed: Aspergillus niger, Aspergillus terreus, Aspergillus flavus, Chaetomium globosum, Paecilomyces variotii, Penicillium funiculosum, Penicillium chrysogenum, Trichoderma viredens. The decrease in the weight of the samples after incubation depends on the content of natural rubber in the composition. With the content of natural rubber in the composition in an amount of 1%, the average weight loss is 0.4% by weight, and when the content of natural rubber is 15% by weight. already ~ 2% of the mass. Starting with the addition of natural rubber in an amount of 1% by weight, the growth of fungi occurs, and the degree of their development is characterized by points 3-5. The resulting compositions are biodegradable, susceptible to the action of fungi, and, therefore, the manufacture of materials based on them will be an environmentally friendly alternative for further use.

Hydrolysates of Sulphur-containing Polypeptides (Keratins) as New Ingredients for Polymeric Composite Materials

2017 ◽  
Vol 44 (3) ◽  
pp. 7-12 ◽  
Author(s):  
D.V. Kolotilin ◽  
E.E. Potapov ◽  
S.V. Reznichenko ◽  
V.V. Ermilov ◽  
E.V. Prut ◽  
...  
Keyword(s):  
Composite Materials ◽  
Natural Rubber ◽  
Polymeric Composite ◽  
Biologically Active ◽  
Raw Material ◽  
Polymeric Composite Materials ◽  
Economic Problems ◽  
Hydrolysis Products ◽  
Elastomer Composites ◽  
Active Substances

In the creation of new polymeric composite materials, the use of biologically active substances, e.g. the hydrolysis products of keratin-containing proteins of different structure, is promising. The possibility of using keratin hydrolysates as modifying additives for improving different properties of various elastomer composites is shown. These are vulcanising agents and vulcanisation accelerators for composite materials based on synthetic polyisoprene; secondary vulcanising agents for elastomer materials based on chlorine-containing rubbers; vulcanisation accelerators for composites. The use of these compounds makes it possible to remove from the composition of materials ecologically harmful components and ingredients that are produced from non-renewable sources of raw material, to solve a number of economic problems, associated, among other things, with the need for import replacement, and also to produce latex composites that in their properties approach latexes of natural rubber.

scholarly journals GLASS-FIBRE REINFORCED COMPOSITES: THE EFFECT OF FIBRE LOADING AND ORIENTATION ON TENSILE AND IMPACT STRENGTH

2017 ◽  
Vol 36 (3) ◽  
pp. 782-787
Author(s):  
O Adekomaya ◽  
K Adama
Keyword(s):  
Composite Materials ◽  
Impact Strength ◽  
Glass Fibre ◽  
Research Work ◽  
Polymeric Composite ◽  
Primary Objective ◽  
Reinforced Composite ◽  
Glass Fibre Reinforced ◽  
The Impact ◽  
Fibre Loading

The primary objective of this research work is to analyse the effect of fibre loading and orientation on the tensile and impact strength of the polymeric composite materials. Fibre reinforced composite materials have been reported to have attracted many applications in view of its low weight and superior strength when compared with the metal matrix composite. While researches have established the weight reduction of fibre reinforced polymer material, few works have reported the impact of orientation on the manufacturing of polymer composite. In this study, series of experimental works were done to demonstrate the manufacturing of glass-fibre reinforced epoxy resin with special attention on the influence of oriented reinforced composite material. The composites were manufactured using hand-lay technique with three different fibre loadings (10, 20, and 30 wt. %) and at two different fibre orientations (30o and 60o). Key of the finding drawn from this research form the basis of discussion and, composite with 60o fibre orientation showed better tensile strength when compared with the neat resin and other oriented (G10E30) fibre reinforced composite. Similar observations were also noticed on the impact strength of these composites which signify the improved mechanical properties of oriented reinforced composite materials. http://dx.doi.org/10.4314/njt.v36i3.17

Peculiarities of tool material wear at polymeric composite blank cutting

2018 ◽  
Vol 2018 (7) ◽  
pp. 27-31
Author(s):  
Юрий Зубарев ◽  
Yuriy Zubarev ◽  
Александр Приемышев ◽  
Alexsandr Priyomyshev
Keyword(s):  
Tool Wear ◽  
Tool Material ◽  
Polymeric Composite ◽  
Physical Models ◽  
Technological Parameters ◽  
Tool Materials ◽  
Materials Used ◽  
The Impact ◽  
Material Wear

Tool materials used for polymeric composite blank machining, kinds of tool material wear arising at machining these blanks, and also the impact of technological parameters upon tool wear are considered. The obtained results allow estimating the potentialities of physical models at polymeric composite blanks cutting.

The Impact of Plant Protection Systems on the Productivity of Soybean Varieties under Irrigated Conditions

2019 ◽  
pp. 109-117
Keyword(s):  
Plant Protection ◽  
Crop Protection ◽  
Production Costs ◽  
Protection System ◽  
Average Weight ◽  
The South ◽  
Biological Origin ◽  
Chemical Protection ◽  
Protection Systems ◽  
The Impact

The application of preparations of biological origin in the protection system of soybean grown under conditions of intensive irrigated crop rotations conforms to the modern tendencies of science and production development. The use of them contributes to solving ecological, production and social-economic problems. The study presents the three-year research on the efficiency of systems protecting soybean from pests and diseases based on biological and chemical preparations. The research was conducted in typical soil and climate conditions of the South of Ukraine. Zonal agricultural methods and generally accepted research methodology were used. The purpose of the research was to create a soybean protection system based on preparations of biological origin, ensuring high productivity of high-quality products reducing a negative impact of the crop production on the environment. The study emphasizes that, under irrigated conditions of the South of Ukraine, the application of biological preparations has a positive impact on the indexes of growth, development and formation of the elements of soybean yield structure. There was an increase in the crop biological weight by 13.8 % and 22.1 % and the number of seeds per plant rose by 11.6 and 14.6 % as a consequence of eliminating harmful organisms with the plant protection systems. The larger ground mass was formed by medium-ripe varieties Danai and Svyatogor, on which the increase from protection measures was higher. Weight 1000 pcs. the seeds did not undergo significant changes. It is established that the larger seeds were formed by Danaya and Svyatogor varieties, in which the average weight is 1000 pcs. seeds were 142 and 136 g, respectively, while in the variety Diona this figure was 133 g. There was an increase in the height of the lowest pod when the total plant height rose. For medium-ripe varieties was characterized by a higher attachment of beans, where the highest values of this indicator acquired in the variety Svyatogor. The medium maturing soybean variety Danaia formed the maximum yield of 3.23 and 3.35 t/ha respectively, when biological and chemical protection systems were applied. The research establishes that the application of the bio-fungicide Psevdobakterin 2 (2.0 l/ha) in the crop protection system at the beginning of soybean flowering and the bio-fungicide Baktofit (2.5 l/ha) with the bio-insecticide Lepidotsid-BTU (10.0 l/ha) at the beginning of pod formation does not reduce the productivity of the soybean varieties under study considerably, when compared to the application of chemical preparations. The research determines that the soybean protection system under study ensures a decrease in the coefficient of soybean water uptake by 7.2-13.0 %, increasing the total water intake to an inconsiderable degree. Biologization of the soybean crop protection system leads to a reduction in production costs compared to the chemical protection system. Taking into account the needs for the collection of additional products, costs increase by an average of 1 thousand UAH/ha, while for chemical protection systems by 1.8 thousand UAH/ha. At the same time, the cost is reduced by 220-360 UAH/t and the profitability of growing crops is increased by 3.8-7.8 %. There has been a reduction in the burden of pesticides on the environment and the production of cleaner products. This indicates the prospect of using the biofungicides Pseudobacterin 2 and Bactophyte and the bioinsecticide Lepidocid-BTU on soybeans to protect plants from pests.

A new method of manufacturing products from polymeric composite materials

2020 ◽  
Author(s):  
D. A. Negrov ◽  
E. N. Eremin ◽  
A. A. Novikov ◽  
V. Yu. Putintsev
Keyword(s):  
Composite Materials ◽  
Polymeric Composite ◽  
New Method ◽  
Polymeric Composite Materials

scholarly journals Body Mass, Physical Activity and Eating Habits Changes during the First COVID-19 Pandemic Lockdown in Poland

2021 ◽  
Vol 18 (11) ◽  
pp. 5682
Author(s):  
Hubert Dobrowolski ◽  
Dariusz Włodarek
Keyword(s):  
Physical Activity ◽  
Body Weight ◽  
Body Mass ◽  
Social Life ◽  
Eating Habits ◽  
High Energy ◽  
High Energy Density ◽  
Average Weight ◽  
Study Participants ◽  
The Impact

The outbreak of the COVID-19 pandemic caused a number of changes in social life around the world. In response to the growing number of infections, some countries have introduced restrictions that may have resulted in the change of the lifestyle. The aim of our study was to investigate the impact of the lockdown on body weight, physical activity and some eating habits of the society. The survey involving 183 people was conducted using a proprietary questionnaire. The mean age of the study participants was 33 ± 11 and mean height 169 ± 8 cm. An average increase in body weight was observed in 49.18% by 0.63 ± 3.7 kg which was the result of a decrease in physical activity and an increase in food consumption. We also observed a decrease in PAL from 1.64 ± 0.15 to 1.58 ± 0.13 and changes in the amount of food and individual groups of products consumption, including alcohol. Among the study participants who did not lose body mass, there was an average weight gain of 2.25 ± 2.5 kg. In conclusion, an increase of weight was shown in about half of the respondents in the study group which was associated with a decrease in physical activity and an increase in the consumption of total food and high energy density products.

scholarly journals Modified Nanoclays/Straw Fillers as Functional Additives of Natural Rubber Biocomposites

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 799
Author(s):  
Justyna Miedzianowska ◽  
Marcin Masłowski ◽  
Przemysław Rybiński ◽  
Krzysztof Strzelec
Keyword(s):  
Natural Rubber ◽  
Raw Materials ◽  
Research Work ◽  
Damping Properties ◽  
Main Research ◽  
Functional Additives ◽  
Different Types ◽  
Elastomeric Materials ◽  
Research Goal ◽  
The Impact

Increasingly, raw materials of natural origin are used as fillers in polymer composites. Such biocomposites have satisfactory properties. To ensure above-average functional properties, modifications of biofillers with other materials are also used. The presented research work aimed to produce and characterize elastomeric materials with a straw-based filler and four different types of montmorillonite. The main research goal was to obtain improved functional parameters of vulcanizates based on natural rubber. A series of composites filled with straw and certain types of modified and unmodified nano-clays in various ratios and amounts were prepared. Then, they were subjected to a series of tests to assess the impact of the hybrids used on the final product. It has been shown that the addition of optimal amounts of biofillers can, inter alia, increase the tensile strength of the composite, improve damping properties, extend the burning time of the material and affect the course of vulcanization or cross-linking density.

scholarly journals Video surveillance methods to evaluate individual feeding response in rainbow trout (Oncorhynchus mykiss, Walbaum)—implications for feeding regime optimisation

2021 ◽  
Author(s):  
Philip Niclas Just ◽  
Bernd Köllner ◽  
Matthew James Slater
Keyword(s):  
Rainbow Trout ◽  
Oncorhynchus Mykiss ◽  
Video Surveillance ◽  
Average Weight ◽  
Short Term ◽  
Feeding Regime ◽  
Daily Feeding ◽  
Juvenile Rainbow Trout ◽  
Feeding Regimes ◽  
The Impact

AbstractPrecisely analysing and optimising feeding regimes is central to salmonid growth performance and delivery of special diets. The current study developed novel video surveillance methods and analysis techniques to assess individual feed intake and minimum pellet intake (MPI) in individually identified juvenile rainbow trout, Oncorhynchus mykiss. Three trials were conducted to test the impact of short-term starvation (N=112 [16 tanks, 7 fish per tank], average weight=27.1±3.4g, age= 119 days), portion numbers per feeding (N=105 [15 tanks, 7 fish per tank], average weight=22.8±2.1g, age= 99 days) and varied numbers of daily feeding events (N=84 [12 tanks, 7 fish per tank], average weight=32.4±3.3g, age= 133 days). All trails were carried out in a recirculating aquaculture system with 20 tanks held at 15 ± 0.5°C. All individuals were code-tagged and high quality video images were taken and analysed to identify all feeding interactions. Individual trout feeding activity under different feeding regimes could be precisely analysed with the video methods developed. Moving from one to two daily feeding events doubled pellet intake per fish from 27.4 ± 5.8 to 52.8 ± 11.5 pellets. Pellet intake (58.8 ± 24.2 pellets) did not increase at three daily feeding events but became more variable across fish. MPI nearly doubled to 30 pellets in fish receiving two daily feeding events (MPI30: chi-squared = 8.74, df = 2, p = 0.01). Short-term starvation had no influence on intake (28 ± 8 pellets/fish) or MPI. Increasing portion number from one (27.8 ± 7.4 pellets fish−1) to two (31.1 ± 7.4 pellets fish−1) or more did not significantly increase the number of ingested pellets. Adjusting the feeding regime by increasing daily feeding events to two, possibly combined with multiple portions, can increase pellet intake and reduce the heteroscedasticity of pellet intake. The methods presented in this study are viable for analysing feeding regimes for juvenile rainbow trout and controlled feedstock/supplement delivery. Implications for analyses with other species and for vaccination optimisation are discussed.

Sign in / Sign up

Export Citation Format

Share Document