scholarly journals Effect of the Matrix on the 1.5μm Photoluminescence of Er-Doped Silicon Quantum Dots

2006 ◽  
Vol 514-516 ◽  
pp. 1116-1120 ◽  
Author(s):  
M.Fátima Cerqueira ◽  
Margarita Stepikhova ◽  
Maria Losurdo ◽  
Teresa Monteiro ◽  
Manuel J. Soares ◽  
...  
Keyword(s):  
Chemical Properties ◽  
Nanocrystalline Silicon ◽  
Raman Spectroscopic ◽  
Silicon Thin Films ◽  
Erbium Ions ◽  
Deposition Parameters ◽  
Composition And Structure ◽  
The Matrix ◽  
Er Doped ◽  
The Impact

Erbium doped nanocrystalline silicon thin films were produced by reactive magnetron r.f. sputtering. Their structural and chemical properties were studied by micro-Raman, spectroscopic ellipsometry and Rutherford backscattering spectroscopy. Films with different crystalline fraction and crystallite size were deposited by changing the deposition parameters. The impact of the composition and structure of Erbium ions environment on the 1.5 µm photoluminescence is discussed.

scholarly journals Spectroscopic ellipsometry study of the layer structure and impurity content in Er-doped nanocrystalline silicon thin films

2001 ◽  
Vol 308-310 ◽  
pp. 374-377 ◽  
Author(s):  
M. Losurdo ◽  
M.F. Cerqueira ◽  
M.V. Stepikhova ◽  
E. Alves ◽  
M.M. Giangregorio ◽  
...  
Keyword(s):  
Thin Films ◽  
Spectroscopic Ellipsometry ◽  
Layer Structure ◽  
Impurity Content ◽  
Nanocrystalline Silicon ◽  
Silicon Thin Films ◽  
Er Doped

Experimental Investigation of the Impact of Annealing on Resistivity of Boron-Doped Hydrogenated Nanocrystalline Silicon Thin Films

2010 ◽  
Vol 29-32 ◽  
pp. 1883-1887
Author(s):  
Hai Bin Pan ◽  
Yuan Tian ◽  
Guang Gui Cheng ◽  
Li Qiang Guo
Keyword(s):  
Thin Films ◽  
Annealing Temperature ◽  
Chemical Vapor ◽  
Nanocrystalline Silicon ◽  
Force Microscopy ◽  
Silicon Thin Films ◽  
Atomic Force ◽  
Boron Doped ◽  
The Impact ◽  
The Relationship

Boron-doped hydrogenated nanocrystalline silicon (nc-Si:H) thin films were deposited by plasma enhanced chemical vapor deposition (PECVD). Microstructures of these films were characterized and analyzed by Raman spectrum and atomic force microscopy (AFM). Thickness and resistivity of these films was measured by high-resolution profilometer and four-point probe respectively. The impact of annealing on boron-doped nc-Si:H thin films’ resistivity and the relationship between resistivity and microstructure were investigated. The results show that annealing and the annealing temperature have great impact on resistivity of nc-Si:H thin films as a result of microstructures changing after annealing. Resistivity of nc-Si:H thin films decreases after annealing, but it rises with the increasing annealing temperature in the range of 250°C to 400°C.

The microstructure of a TiB2/Ti-47 Al composite material

1989 ◽  
Vol 47 ◽  
pp. 674-675
Author(s):  
O. Popoola ◽  
A.H. Heuer ◽  
P. Pirouz
Keyword(s):  
Composite Material ◽  
Ion Beam ◽  
Chemical Properties ◽  
Intermetallic Alloys ◽  
Transmission Electron ◽  
Diamond Polishing ◽  
Al Composite ◽  
The Matrix ◽  
Argon Ion ◽  
And Chemical Properties

The addition of fibres or particles (TiB2, SiC etc.) into TiAl intermetallic alloys could increase their toughness without compromising their good high temperature mechanical and chemical properties. This paper briefly discribes the microstructure developed by a TiAl/TiB2 composite material fabricated with the XD™ process and forged at 960°C.The specimens for transmission electron microscopy (TEM) were prepared in the usual way (i.e. diamond polishing and argon ion beam thinning) and examined on a JEOL 4000EX for microstucture and on a Philips 400T equipped with a SiLi detector for microanalyses.The matrix was predominantly γ (TiAl with L10 structure) and α2(TisAl with DO 19 structure) phases with various morphologies shown in figure 1.

Giant Anisotropy of Conductivity in Hydrogenated Nanocrystalline Silicon Thin Films

1998 ◽  
Vol 536 ◽  
Author(s):  
A. B. Pevtsov ◽  
N. A. Feoktistov ◽  
V. G. Golubev
Keyword(s):  
Thin Films ◽  
Film Thickness ◽  
Percolation Theory ◽  
Nanocrystalline Silicon ◽  
Spatial Light Modulators ◽  
Light Emitting ◽  
Light Modulators ◽  
Silicon Thin Films ◽  
Longitudinal Conductivity ◽  
Transverse Conductivity

AbstractThin (<1000 Å) hydrogenated nanocrystalline silicon films are widely used in solar cells, light emitting diodes, and spatial light modulators. In this work the conductivity of doped and undoped amorphous-nanocrystalline silicon thin films is studied as a function of film thickness: a giant anisotropy of conductivity is established. The longitudinal conductivity decreases dramatically (by a factor of 109 − 1010) as the layer thickness is reduced from 1500 Å to 200 Å, while the transverse conductivity remains close to that of a doped a- Si:H. The data obtained are interpreted in terms of the percolation theory.

Impact Strength, Flexural Modulus and Wear Rate of PMMA Composites Reinforced by Eggshell Powders

2020 ◽  
Vol 38 (7A) ◽  
pp. 960-966
Author(s):  
Aseel M. Abdullah ◽  
Hussein Jaber ◽  
Hanaa A. Al-Kaisy
Keyword(s):  
Impact Strength ◽  
Wear Rate ◽  
Flexural Modulus ◽  
Matrix Material ◽  
Weight Fraction ◽  
Pure Pmma ◽  
Calcination Process ◽  
The Matrix ◽  
The Impact ◽  
Interface Bond

In the present study, the impact strength, flexural modulus, and wear rate of poly methyl methacrylate (PMMA) with eggshell powder (ESP) composites have been investigated. The PMMA used as a matrix material reinforced with ESP at two different states (including untreated eggshell powder (UTESP) and treated eggshell powder (TESP)). Both UTESP and TESP were mixed with PMMA at different weight fractions ranged from (1-5) wt.%. The results revealed that the mechanical properties of the PMMA/ESP composites were enhanced steadily with increasing eggshell contents. The samples with 5 wt.% of UTESP and TESP additions give the maximum values of impact strength, about twice the value of the pure PMMA sample. The calcination process of eggshells powders gives better properties of the PMMA samples compared with the UTESP at the same weight fraction due to improvements in the interface bond between the matrix and particles. The wear characteristics of the PMMA composites decrease by about 57% with increases the weight fraction of TESP up to 5 wt.%. The flexural modulus values are slightly enhanced by increasing of the ESP contents in the PMMA composites.

scholarly journals The Impact of Filler Geometry on Polylactic Acid-Based Sustainable Polymer Composites

Molecules ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 149
Author(s):  
Karol Leluk ◽  
Stanisław Frąckowiak ◽  
Joanna Ludwiczak ◽  
Tomasz Rydzkowski ◽  
Vijay Kumar Thakur
Keyword(s):  
Polymer Composites ◽  
Polylactic Acid ◽  
Matrix Material ◽  
Chemical Properties ◽  
Precipitated Calcium Carbonate ◽  
Cellulose Fibres ◽  
Shape Factors ◽  
Pure Cellulose ◽  
Physico Chemical ◽  
The Impact

Recently, biocomposites have emerged as materials of great interest to the scientists and industry around the globe. Among various polymers, polylactic acid (PLA) is a popular matrix material with high potential for advanced applications. Various particulate materials and nanoparticles have been used as the filler in PLA based matrix. One of the extensively studied filler is cellulose. However, cellulose fibres, due to their hydrophilic nature, are difficult to blend with a hydrophobic polymer matrix. This leads to agglomeration and creates voids, reducing the mechanical strength of the resulting composite. Moreover, the role of the various forms of pure cellulose and its particle shape factors has not been analyzed in most of the current literature. Therefore, in this work, materials of various shapes and shape factors were selected as fillers for the production of polymer composites using Polylactic acid as a matrix to fill this knowledge gap. In particular, pure cellulose fibres (three types with different elongation coefficient) and two mineral nanocomponents: precipitated calcium carbonate and montmorillonite were used. The composites were prepared by a melt blending process using two different levels of fillers: 5% and 30%. Then, the analysis of their thermomechanical and physico-chemical properties was carried out. The obtained results were presented graphically and discussed in terms of their shape and degree of filling.

scholarly journals The Interactions between Polyphenols and Microorganisms, Especially Gut Microbiota

Antioxidants ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 188
Author(s):  
Małgorzata Makarewicz ◽  
Iwona Drożdż ◽  
Tomasz Tarko ◽  
Aleksandra Duda-Chodak
Keyword(s):  
Intestinal Bacteria ◽  
Research Data ◽  
Bioactive Metabolites ◽  
Human Organism ◽  
Comprehensive Knowledge ◽  
Bidirectional Relationship ◽  
The Matrix ◽  
Intestinal Pathogens ◽  
The Impact

This review presents the comprehensive knowledge about the bidirectional relationship between polyphenols and the gut microbiome. The first part is related to polyphenols’ impacts on various microorganisms, especially bacteria, and their influence on intestinal pathogens. The research data on the mechanisms of polyphenol action were collected together and organized. The impact of various polyphenols groups on intestinal bacteria both on the whole “microbiota” and on particular species, including probiotics, are presented. Moreover, the impact of polyphenols present in food (bound to the matrix) was compared with the purified polyphenols (such as in dietary supplements) as well as polyphenols in the form of derivatives (such as glycosides) with those in the form of aglycones. The second part of the paper discusses in detail the mechanisms (pathways) and the role of bacterial biotransformation of the most important groups of polyphenols, including the production of bioactive metabolites with a significant impact on the human organism (both positive and negative).

scholarly journals Influence of deposition parameters on the optical absorption of amorphous silicon thin films

2020 ◽  
Vol 2 (3) ◽  
Author(s):  
Lukas Terkowski ◽  
Iain W. Martin ◽  
Daniel Axmann ◽  
Malte Behrendsen ◽  
Felix Pein ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Absorption ◽  
Amorphous Silicon ◽  
Silicon Thin Films ◽  
Deposition Parameters

scholarly journals Reliability Assessment of a Multi-State HVDC System by Combining Markov and Matrix-Based Methods

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3097
Author(s):  
Roberto Benato ◽  
Antonio Chiarelli ◽  
Sebastian Dambone Sessa
Keyword(s):  
Current System ◽  
Estimation Method ◽  
Reliability Estimation ◽  
Voltage Source ◽  
Voltage Source Converter ◽  
Hvdc System ◽  
Critical Elements ◽  
The Matrix ◽  
The Impact

The purpose of this paper is to highlight that, in order to assess the availability of different HVDC cable transmission systems, a more detailed characterization of the cable management significantly affects the availability estimation since the cable represents one of the most critical elements of such systems. The analyzed case study consists of a multi-terminal direct current system based on both line commutated converter and voltage source converter technologies in different configurations, whose availability is computed for different transmitted power capacities. For these analyses, the matrix-based reliability estimation method is exploited together with the Monte Carlo approach and the Markov state space one. This paper shows how reliability analysis requires a deep knowledge of the real installation conditions. The impact of these conditions on the reliability evaluation and the involved benefits are also presented.

Sign in / Sign up

Export Citation Format

Share Document