Novel synthesis of a NiMoP phosphide catalyst via carbothermal reduction for dry reforming of methane

2021 ◽  
Author(s):  
Xinyu Chen ◽  
Wei Ding ◽  
Zhiwei Yao ◽  
Na Sun ◽  
Zhimeng Wang ◽  
...  
Keyword(s):  
Particle Size ◽  
Carbon Content ◽  
Carbothermal Reduction ◽  
Average Particle Size ◽  
Dry Reforming ◽  
Dry Reforming Of Methane ◽  
Average Particle ◽  
Novel Synthesis ◽  
Highly Dispersed

A Highly dispersed NiMoP phosphide catalyst with an average particle size of 9.1 nm and a carbon content of 53.5 wt% was firstly synthesized by carbothermal route using glucose as...

scholarly journals Dry Reforming of Methane Using Ni Catalyst Supported on ZrO2: The Effect of Different Sources of Zirconia

Catalysts ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 827
Author(s):  
Ahmed Aidid Ibrahim ◽  
Anis Hamza Fakeeha ◽  
Ahmed Elhag Abasaeed ◽  
Ahmed Sadeq Al-Fatesh
Keyword(s):  
Supported Catalysts ◽  
Average Particle Size ◽  
Cost Effective ◽  
Dry Reforming ◽  
Dry Reforming Of Methane ◽  
Bet Surface Area ◽  
Ni Catalyst ◽  
Average Particle ◽  
Tem Analysis ◽  
Different Sources

Dry reforming of methane (DRM) has a substantial potential to provide a cost-effective process and in reducing greenhouse gases. Its application has been hindered by carbon deposition and instability problems. The use of an appropriate catalyst is influenced by the support type. The objective of this investigation is to elucidate the effect of different sources of ZrO2 support. Four kinds of ZrO2, namely RC-100 and Z-3215, MKnano, and ELTN were acquired from Japan, Canada, and China, respectively. The catalyst samples were analyzed by BET, XRD, TPR, TPD, TEM, TGA, TPO, FT-IR, and Raman. The analysis of the structural properties displayed that all Ni-supported catalysts, regardless of their source, are mesoporous and that 5Ni-RC-100 possessed the highest BET surface area of 17.7 m2/g and 5Ni-MKnano had the lowest value of BET 3.16 m2/g. In the TPD and TEM analysis, the 5Ni-RC-100 catalyst presented the highest intensity of basicity and the minimum average particle size of 3.35 nm, respectively. The 5Ni-RC-100 catalyst outperformed 5Ni-ELTN by exhibiting 44% higher CH4 conversion; however, 5Ni-RC-100 gave the highest weight loss in the TGA analysis of 66%.

scholarly journals Получение высокодисперсного порошка монооксида олова методом испарения-конденсации при нагреве сфокусированным излучением субтерагерцевого гиротрона

2021 ◽  
Vol 47 (5) ◽  
pp. 51
Author(s):  
А.И. Цветков ◽  
А.В. Водопьянов ◽  
Д.А. Мансфельд ◽  
А.А. Орловский ◽  
С.А. Буланова ◽  
...  
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Average Particle Size ◽  
Condensation Process ◽  
Average Particle ◽  
Experimental Setup ◽  
Initial Material ◽  
Condensation Method ◽  
Weight Content ◽  
Highly Dispersed

A method of obtaining highly dispersed tin (II) oxide (SnO) powder by the evaporation-condensation method was investigated when the initial material was heated by focused radiation of a subterahertz gyrotron with a frequency of 0.26 THz and a power of 1 kW. The process was carried out with a purge with nitrogen inert with respect to SnO. A powder with a SnO weight content of 92% was obtained. The specific surface was 7.20 m2/g, which corresponds to an average particle size of 130 nm. The characteristics of the obtained powder are analyzed. The applicability of the experimental setup for the production of nanopowders from compounds requiring special gas conditions during the evaporation-condensation process has been demonstrated.

Determination of grinding parameters of fenugreek seed

1970 ◽  
Vol 26 (1) ◽  
pp. 16 ◽  
Author(s):  
S Balasubramanian ◽  
Rajkumar Rajkumar ◽  
K K Singh
Keyword(s):  
Particle Size ◽  
Energy Consumption ◽  
Moisture Content ◽  
Specific Energy ◽  
Feed Rate ◽  
Average Particle Size ◽  
Specific Energy Consumption ◽  
Average Particle ◽  
Fenugreek Seeds ◽  
Fenugreek Seed

Experiment to identify ambient grinding conditions and energy consumed was conducted for fenugreek. Fenugreek seeds at three moisture content (5.1%, 11.5% and 17.3%, d.b.) were ground using a micro pulverizer hammer mill with different grinding screen openings (0.5, 1.0 and 1.5 mm) and feed rate (8, 16 and 24 kg h-1) at 3000 rpm. Physical properties of fenugreek seeds were also determined. Specific energy consumptions were found to decrease from 204.67 to 23.09 kJ kg-1 for increasing levels of feed rate and grinder screen openings. On the other hand specific energy consumption increased with increasing moisture content. The highest specific energy consumption was recorded for 17.3% moisture content and 8 kg h-1 feed rate with 0.5 mm screen opening. Average particle size decreased from 1.06 to 0.39 mm with increase of moisture content and grinder screen opening. It has been observed that the average particle size was minimum at 0.5 mm screen opening and 8 kg h-1 feed rate at lower moisture content. Bond’s work index and Kick’s constant were found to increase from 8.97 to 950.92 kWh kg-1 and 0.932 to 78.851 kWh kg-1 with the increase of moisture content, feed rate and grinder screen opening, respectively. Size reduction ratio and grinding effectiveness of fenugreek seed were found to decrease from 4.11 to 1.61 and 0.0118 to 0.0018 with the increase of moisture content, feed rate and grinder screen opening, respectively. The loose and compact bulk densities varied from 219.2 to 719.4 kg m-3 and 137.3 to 736.2 kg m-3, respectively.  

Formulating SLN and NLC as Innovative Drug Delivery Systems for Non-Invasive Routes of Drug Administration

2020 ◽  
Vol 27 (22) ◽  
pp. 3623-3656 ◽  
Author(s):  
Bruno Fonseca-Santos ◽  
Patrícia Bento Silva ◽  
Roberta Balansin Rigon ◽  
Mariana Rillo Sato ◽  
Marlus Chorilli
Keyword(s):  
Drug Delivery ◽  
Particle Size ◽  
Drug Release ◽  
Drug Loading ◽  
Average Particle Size ◽  
Delivery Systems ◽  
Average Particle ◽  
Minor Importance ◽  
Routes Of Administration ◽  
Non Invasive

Colloidal carriers diverge depending on their composition, ability to incorporate drugs and applicability, but the common feature is the small average particle size. Among the carriers with the potential nanostructured drug delivery application there are SLN and NLC. These nanostructured systems consist of complex lipids and highly purified mixtures of glycerides having varying particle size. Also, these systems have shown physical stability, protection capacity of unstable drugs, release control ability, excellent tolerability, possibility of vectorization, and no reported production problems related to large-scale. Several production procedures can be applied to achieve high association efficiency between the bioactive and the carrier, depending on the physicochemical properties of both, as well as on the production procedure applied. The whole set of unique advantages such as enhanced drug loading capacity, prevention of drug expulsion, leads to more flexibility for modulation of drug release and makes Lipid-based nanocarriers (LNCs) versatile delivery system for various routes of administration. The route of administration has a significant impact on the therapeutic outcome of a drug. Thus, the non-invasive routes, which were of minor importance as parts of drug delivery in the past, have assumed added importance drugs, proteins, peptides and biopharmaceuticals drug delivery and these include nasal, buccal, vaginal and transdermal routes. The objective of this paper is to present the state of the art concerning the application of the lipid nanocarriers designated for non-invasive routes of administration. In this manner, this review presents an innovative technological platform to develop nanostructured delivery systems with great versatility of application in non-invasive routes of administration and targeting drug release.

Azithromycin nanosuspension preparation using evaporative precipitation into aqueous solution (EPAS) method and its comparative dissolution study

2020 ◽  
Vol 17 ◽  
Author(s):  
Mohammad Hossain Shariare ◽  
Tonmoy Kumar Mondal ◽  
Hani Alothaid ◽  
Md. Didaruzzaman Sohel ◽  
MD Wadud ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Particle Size ◽  
Dissolution Rate ◽  
Average Particle Size ◽  
Scale Up ◽  
Average Particle ◽  
Total Drug ◽  
Residual Solvent ◽  
Dissolution Study ◽  
Drug Content

Aim: EPAS (evaporative precipitation into aqueous solution) was used in the current studies to prepare azithromycin nanosuspensions and investigate the physicochemical characteristics for the nanosuspension batches with the aim of enhancing the dissolution rate of the nanopreparation to improve bioavailability. Methods: EPAS method used in this study for preparing azithromycin nanosuspension was achieved through developing an in-house instrumentation method. Particle size distribution was measured using Zetasizer Nano S without sample dilution. Dissolved azithromycin nanosuspensions were also compared with raw azithromycin powder and commercially available products. Total drug content of nanosuspension batches were measured using an Ultra-Performance Liquid Chromatography (UPLC) system with Photodiode Array (PDA) detector while residual solvent was measured using gas chromatography (GC). Results: The average particle size of azithromycin nanosuspension was 447.2 nm and total drug content was measured to be 97.81% upon recovery. Dissolution study data showed significant increase in dissolution rate for nanosuspension batch when compared to raw azithromycin and commercial version (microsuspension). The residual solvent found for azithromycin nanosuspension is 0.000098023 mg/ mL or 98.023 ppb. Conclusion: EPAS was successfully used to prepare azithromycin nanoparticles that exhibited significantly enhanced dissolution rate. Further studies are required to scale up the process and determine long term stability of the nanoparticles.

scholarly journals Evaluation of the Effects of Filler Fineness on the Properties of an Epoxy Asphalt Mixture

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2003
Author(s):  
Wei Xu ◽  
Jintao Wei ◽  
Zhengxiong Chen ◽  
Feng Wang ◽  
Jian Zhao
Keyword(s):  
Particle Size ◽  
Average Particle Size ◽  
Asphalt Mixture ◽  
Average Particle ◽  
Fine Dust ◽  
Bonding Structure ◽  
Epoxy Asphalt ◽  
Mineral Powder ◽  
Marshall Stability ◽  
Mixture Sample

The type and fineness of a filler significantly affect the performance of an asphalt mixture. There is a lack of specific research on the effects of filler fineness and dust from aggregates on the properties of epoxy asphalt (EA) mixtures. The effects of aggregate dust and mineral powder on the properties of an EA mixture were evaluated. These filler were tested to determine their fineness, specific surface area and mineral composition. The effects of these fillers on the EA mastic sample and mixture were evaluated. The morphology of the EA mastic samples was analyzed using scanning electron microscopy (SEM). The effects of the fillers on the Marshall stability, tensile strength and fatigue performance of the EA mixture were evaluated. The dust from the aggregates exhibited an even particle size distribution, and its average particle size was approximately 20% of that of the mineral powder. The SEM microanalysis showed that the EA mastic sample containing relatively fine dust formed a tight and dense interfacial bonding structure with the aggregate. The EA mixture sample containing filler composed of dust from aggregate had a significantly higher strength and longer fatigue life than that of the EA sample containing filler composed of mineral powder.

scholarly journals Surface Activity of Humic Acid and Its Sub-Fractions from Forest Soil

2021 ◽  
Vol 13 (15) ◽  
pp. 8122
Author(s):  
Shijie Tian ◽  
Weiqiang Tan ◽  
Xinyuan Wang ◽  
Tingting Li ◽  
Fanhao Song ◽  
...  
Keyword(s):  
Surface Tension ◽  
Particle Size ◽  
Humic Acid ◽  
Forest Soil ◽  
Surface Activity ◽  
Self Assembly ◽  
Average Particle Size ◽  
Gaussian Model ◽  
Exponential Model ◽  
Average Particle

Surface activity of humic acid (HA) and its six sub-fractions isolated from forest soil were characterized by surface tension measurements, dynamic light scattering, and laser doppler electrophoresis. The surface tension of HA and its sub-fractions reduced from 72.4 mN·m−1 to 36.8 mN·m−1 in exponential model with the increasing concentration from 0 to 2000 mg·L−1. The critical micelle concentration (CMC) and Z-average particle size ranged from 216–1024 mg·L−1 and 108.2–186.9 nm for HA and its sub-fractions, respectively. The CMC have related with alkyl C, O-alkyl C, aromatic C, and carbonyl C (p < 0.05), respectively, and could be predicted with the multiple linear regression equation of CMC, CMC = 18896 − 6.9 × C-296 × alkyl C-331 × aromatic C-17019 × H/C + 4054 × HB/HI (p < 0.05). The maximum particle size was 5000 nm after filtered by a membrane with pore size of 450 nm, indicating HA and its sub-fractions could progressed self-assembly at pH 6.86. The aggregate sizes of number-base particle size distributions were mainly in six clusters including 2 ± 1 nm, 5 ± 2 nm, 10 ± 3 nm, 21 ± 8 nm, 40 ± 10 nm, and >50 nm analyzed by Gaussian model that maybe due to the inconsistency of the components and structures of the HA sub-fractions, requiring further study. It is significance to explore the surface activity of HA and its sub-fractions, which is helpful to clarify the environmental behavior of HA.

Microstructure Characterization of Ag Nanoparticles Prepared by Hydrothermal Method

2012 ◽  
Vol 476-478 ◽  
pp. 1138-1141
Author(s):  
Zhi Qiang Wei ◽  
Qiang Wei ◽  
Li Gang Liu ◽  
Hua Yang ◽  
Xiao Juan Wu
Keyword(s):  
Crystal Structure ◽  
Particle Size ◽  
Hydrothermal Method ◽  
Ag Nanoparticles ◽  
Average Particle Size ◽  
Average Particle ◽  
Face Centered Cubic ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Face Centered

Ag nanoparticles were successfully synthesized by hydrothermal method under the polyol system combined with traces of sodium chloride, Silver nitrate(AgNO3) and polyvinylpyrrolidone (PVP) acted as the silver source and dispersant respectively. The samples by this process were characterized via X-ray powder diffraction (XRD), Brunauer–Emmett–Teller (BET) adsorption equation, transmission electron microscopy (TEM) and the corresponding selected area electron diffraction (SAED) to determine the chemical composition, particle size, crystal structure and morphology. The experiment results indicate that the crystal structure of the samples is face centered cubic (FCC) structure as same as the bulk materials, The specific surface area is 24 m2/g, the particle size distribution ranging from10 to 50 nm, with an average particle size about 26 nm obtained by TEM and confirmed by XRD and BET results.

scholarly journals Wheat Grinding Process with Low Moisture Content: A New Approach for Wholemeal Flour Production

Processes ◽  
2020 ◽  
Vol 9 (1) ◽  
pp. 32
Author(s):  
Waleed H. Hassoon ◽  
Dariusz Dziki ◽  
Antoni Miś ◽  
Beata Biernacka
Keyword(s):  
Particle Size ◽  
Moisture Content ◽  
Average Particle Size ◽  
Average Particle ◽  
Grinding Process ◽  
Mixing Properties ◽  
New Approach ◽  
Grain Moisture ◽  
Flour Production ◽  
And Storage

The objective of this study was to determine the grinding characteristics of wheat with a low moisture content. Two kinds of wheat—soft spelt wheat and hard Khorasan wheat—were dried at 45 °C to reduce the moisture content from 12% to 5% (wet basis). Air drying at 45 °C and storage in a climatic chamber (45 °C, 10% relative humidity) were the methods used for grain dehydration. The grinding process was carried out using a knife mill. After grinding, the particle size distribution, average particle size and grinding energy indices were determined. In addition, the dough mixing properties of wholemeal flour dough were studied using a farinograph. It was observed that decreasing the moisture content in wheat grains from 12% to 5% made the grinding process more effective. As a result, the average particle size of the ground material was decreased. This effect was found in both soft and hard wheat. Importantly, lowering the grain moisture led to about a twofold decrease in the required grinding energy. Moreover, the flour obtained from the dried grains showed higher water absorption and higher dough stability during mixing. However, the method of grain dehydration had little or no effect on the results of the grinding process or dough properties.

COMPARATIVE STUDY OF DIELECTRIC BEHAVIOR OF Mn0.4Zn0.6Fe2O4 NANOFERRITE BY CITRATE PRECURSOR METHOD

2008 ◽  
Vol 22 (16) ◽  
pp. 2537-2544 ◽  
Author(s):  
PREETI MATHUR ◽  
ATUL THAKUR ◽  
M. SINGH
Keyword(s):  
Particle Size ◽  
Dielectric Constant ◽  
Comparative Study ◽  
Average Particle Size ◽  
Dielectric Behavior ◽  
Average Particle ◽  
Oxidizing Agent ◽  
Precursor Method ◽  
Citrate Precursor ◽  
Citrate Precursor Method

In the present work, comparative study of the dielectric behavior of Mn 0.4 Zn 0.6 Fe 2 O 4 ferrite synthesized with and without H 2 O 2 (hydrogen peroxide) has been presented. The dc resistivity has been improved by the citrate precursor method as compared to the ceramic method, and it is further improved by the addition of H 2 O 2, which acts as a strong oxidizing agent. We have shown by means of X-ray diffraction that the resulting ferrite is made up of nanocrystallites and the average size of these nanocrystallites–calculated by Scherrer's formula–depends on the polarizer. The average particle size was found to be ~70 nm with H 2 O 2 and ~88 nm without H 2 O 2. The particle size is further confirmed by scanning electron microscopy. Both the results are found to be in good agreement. The decrease in dielectric constant and dielectric loss factor by addition of oxidizing agent is justified by inverse proportionality between the resistivity and dielectric constant. Possible mechanisms contributing to these processes have been discussed.

Sign in / Sign up

Export Citation Format

Share Document