scholarly journals Introduction of cold-in-place recycling technology in practice as an innovative tool

2021 ◽  
Vol 1209 (1) ◽  
pp. 012080
Author(s):  
R Kovács ◽  
J Mandula
Keyword(s):  
Surface Treatment ◽  
Fatigue Failure ◽  
Raw Materials ◽  
Heavy Traffic ◽  
Innovative Technology ◽  
Widespread Application ◽  
Construction Companies ◽  
Recycling Technology ◽  
The Impact ◽  
Deep Defects

Abstract Roads exposed to continuous and heavy traffic often shown sight of damage which particularly extend to the underlying layers of roads. Due to the advantages of less raw materials and fossil fuel consumption, lower carbon footprint and the capability of pavement performance improvement enormous effect have been done in the western countries over the past decades. Thanks to the efforts of some construction companies in Slovakia our focus in this paper on the innovation technology of cold-in-place recycling is given. The presumption of success of this innovative technology is the introduction and use of the set of a powerful and interconnected machines. This technology allows the repair of deep defects, rutting and fatigue failure, which cannot be done by surface treatment with significant reducing the impact on the environment, material, and economical savings. Moreover, it enables the repair of deep defects, rutting and fatigue failure, which cannot be done by surface treatment. To promote the widespread application of cold-in-place recycling technology in practice and to monitor the progress of developments, this article has examined and discussed the basic aspects of the use of this technology based on laboratory analyzes of recycled material.

Influence of Socio-Economy in the Next Generation of Thermal Management Solutions for Electronics Consumer Products

2008 ◽  
Author(s):  
Gamal Refai-Ahmed
Keyword(s):  
High Performance ◽  
Heat Dissipation ◽  
Raw Materials ◽  
Cost Effective ◽  
Electronics Packaging ◽  
Consumer Products ◽  
Innovative Technology ◽  
Target Market ◽  
The World ◽  
The Impact

The past few decades have seen a number of countries around the world emerge as a growing market for high performance computers. This present study examines, in more detail, how socio-economic influences are shaping the demand function and how some computing landscapes are changing as a consequence. This study is addressing one of the key initiatives to enable 50 percent of the world’s population with access to the World Wide Web. Furthermore, this investigation is addressing the challenges for electronics packaging Engineers and Researchers. Therefore, the rational of the developed technology based on the understanding target market and usages will be given. The impact of addressing the heat dissipation and managing the use of the raw materials of the intended products are discussed. In addition, how the electronics packaging engineers can focus on developing affordable innovative technology. Finally, the impact of all of the above is examined in developing the cost effective solution from a global point of view.

scholarly journals Impact of construction practices on the environment a case study of Kano State, Nigeria

2020 ◽  
Vol 12 (1) ◽  
pp. 18-23
Author(s):  
B.S. Aliyu ◽  
M.Z. Moyi ◽  
L.Z. Fareed ◽  
H.J. Sule ◽  
A.M. Nazifi ◽  
...  
Keyword(s):  
Environmental Impact ◽  
Environmental Impacts ◽  
Raw Materials ◽  
Electricity Consumption ◽  
Sustainable Construction ◽  
Construction Company ◽  
Construction Companies ◽  
Construction Design ◽  
Importance Index ◽  
The Impact

The Physical environment is being disturbed by numerous problems, including those caused by the constructions activities, such problems impacts on the environment right from the initial stage, operational and to the end of the life span of the built structure. The aim of the study was to suggest the main environmental impacts of construction in Kano state. About twenty six construction impacts were reveals from the past researches. However, all the impact was classified into nine main classes. Data for the study were collected from questionnaires and interviews survey administered to stakeholders of construction industry in Kano State. Data collected were analyzed and ranked using Relative Importance Index (RII), suggesting that they significantly impact on the environment thereby causing environmental degradation. Based on the results resource consumption was ranked highest among the major environmental impacts of constructing in Kano. The highest class, consist raw materials, water, fuel and electricity consumption. The paper concludes with recommendation which includes enforcement of extant rules, regulation and ethical code by government legislative on construction stakeholders, government should formulate and ensuring adequate use of construction design that will suite the environment in Kano. Also, all forms of construction practices should be subjected to an environmental impact assessment to determine the potential impacts and also formulate the ways to overcome it before execution. The study suggest also that, the chair personnel in construction companies should formulate some rules, code of conducts that will ensure good and fair sustainable construction practices in Kano. Keywords: Construction Company, Construction Practices, Environmental Impact, Kano.

Balanced Scorecard in the strategic planning of a construction company

2018 ◽  
Vol 1 (1) ◽  
pp. 1
Author(s):  
Roberth Frias ◽  
Maria Medina
Keyword(s):  
Strategic Planning ◽  
Strategic Management ◽  
Balanced Scorecard ◽  
Organization Theory ◽  
Management Control ◽  
Management Tool ◽  
The Balanced Scorecard ◽  
Construction Company ◽  
Construction Companies ◽  
The Impact

This research focused on the strategic management tool Balanced Scorecard and strategic planning, as a guide to guide the management of companies, allowing communication and the functionality of the strategy using KPIs that allow to identify, maintain control and increase efficiency and the achievement of optimal results. For the deductive hypothetical analysis, the specific factors that affect business management performance were grouped into two variables: Balanced Scorecard and Strategic Planning. The objective of the work was to demonstrate the impact of the Balanced Scorecard in the strategic planning of a construction company. In order to support the research, the following theories were approached: the Financial Theory, the Economic Theory of the Company, the Transaction Costs, the Network Theory, the Organization Theory, the Dependence on Resources, the Strategic Management Theory and the Business Diagnosis Theory. The result obtained confirms the hypothesis that there is a significant incidence of the Balanced Scorecard in the strategic planning of construction companies. In conclusion, the construction company has obtained significant improvements in the results in each of the indicators evaluated with the implementation of the Balanced Scorecard, demonstrating improvements in their management results, affirming that there is better performance and management control allowing them to achieve the organizational objectives set.

Оrganic Meat Production of Broiler Chickens Hubbard Redbro Cross

2020 ◽  
Keyword(s):  
Broiler Chickens ◽  
Raw Materials ◽  
Animal Health ◽  
Meat Products ◽  
Poultry Meat ◽  
Meat Production ◽  
Significant Difference ◽  
Environmentally Safe ◽  
The Impact

This article presents the results of studying the impact of housing and feeding conditions on broiler chickens of Hubbard RedBro cross, as well as the quality of products obtained when using floor and cage content, in a farm. It established that when receiving a mixed feed of own production using feed raw materials grown on a farm without the use of pesticides, a statistically significant decrease in potentially dangerous substances for animal health is recorded. Compared with factory feed, it has reduced the content of pesticides by 14 times, and mercury and arsenic by 24 times, cadmium by five times, and lead by ten times. The results of the study of economic indicators of growing Hubbard RedBro cross broiler chickens, as well as the chemical composition and quality of carcasses, indicated that there was no significant difference between the floor and cell conditions of keeping. Still, the use of a diet based on eco-feeds contributed to a statistically significant decrease in the concentration of toxic metals in the muscles of the poultry of the experimental groups. As a result, it found that the use of the studied compound feed in the diets of broiler chickens increased the indicators of Biosafety and ensured the production of environmentally safe ("organic") poultry meat products.

Impact of Raw Materials and Processing Techniques on The Microbiological Quality of Egyptian Domiati Cheese

2020 ◽  
Keyword(s):  
Raw Materials ◽  
Microbiological Quality ◽  
Raw Milk ◽  
Plate Count ◽  
E Coli ◽  
Fresh Cheese ◽  
Processing Techniques ◽  
The Impact ◽  
Total Yeast

Domiati cheese is the most popular brand of cheese ripened in brine in the Middle East in terms of consumed quantities. This study was performed to investigate the impact of the microbiological quality of the used raw materials, the applied traditional processing techniques and ripening period on the quality and safety of the produced cheese. Three hundred random composite samples were collected from three factories at Fayoum Governorate, Egypt. Collected samples represent twenty-five each of: raw milk, table salt, calf rennet, microbial rennet, water, environmental air, whey, fresh cheese, ripened cheese & swabs from: worker hands; cheese molds and utensils; tanks. All samples were examined microbiologically for Standard Plate Count (SPC), coliforms count, Staphylococcus aureus (S. aureus) count, total yeast & mould count, presence of E. coli, Salmonellae and Listeria monocytogenes (L. monocytogenes). The mean value of SPC, coliforms, S. aureus and total yeast & mould counts ranged from (79×102 CFU/m3 for air to 13×108 CFU/g for fresh cheese), (7×102 MPN/ cm2 for tank swabs to 80×106 MPN/ml for raw milk), (9×102 CFU/g for salt to 69×106 CFU/g for fresh cheese) and (2×102 CFU/cm2 for hand swabs to 60×104 CFU/g for fresh cheese), respectively. Whereas, E. coli, Salmonella and L. monocytogenes failed to be detected in all examined samples. There were significant differences in all determined microbiological parameters (p ≤0.05) between fresh and ripened cheese which may be attributed to different adverse conditions such as water activity, pH, salt content and temperature carried out to improve the quality of the product.

New surface treatment techniques to minimize copper alloy leaching in drinking water

2012 ◽  
Vol 7 (4) ◽  
Author(s):  
Norikazu Sugaya
Keyword(s):  
Surface Treatment ◽  
Raw Materials ◽  
Organic Film ◽  
Forming Process ◽  
Mixed Acid ◽  
Treatment Techniques ◽  
Acid Washing ◽  
Washing Process ◽  
Film Forming ◽  
Materials Used

This new surface treatment is simple and easy as well as low in cost. The processes can even be performed by hand. Pharmaceutical raw materials used for the surface treatment, such as hydrochloric acid and nitric acid used in a mixed acid washing process and vegetable oil used in an organic film forming process, are easily obtained in many countries.

scholarly journals 2-Piece Cork Stoppers as Alternative for Valorization of Thin Cork Planks: Analysis by LCA Methodology

Foods ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 873
Author(s):  
Francisco Javier Flor-Montalvo ◽  
Agustín Sánchez-Toledo Ledesma ◽  
Eduardo Martínez Cámara ◽  
Emilio Jiménez-Macías ◽  
Jorge Luis García-Alcaraz ◽  
...  
Keyword(s):  
Life Cycle Assessment ◽  
Life Cycle ◽  
Raw Materials ◽  
Lca Methodology ◽  
Significant Difference ◽  
Different Dimensions ◽  
The Impact ◽  
Different Thickness ◽  
Cork Stoppers ◽  
Wine Bottle

Natural stoppers are a magnificent closure for the production of aging wines and unique wines, whose application is limited by the availability of raw materials and more specifically of cork sheets of different thickness and quality. The growing demand for quality wine bottle closures leads to the search for alternative stopper production. The two-piece stopper is an alternative since it uses non-usable plates in a conventional way for the production of quality caps. The present study has analyzed the impact of the manufacture of these two-piece stoppers using different methodologies and for different dimensions by developing an LCA (Life Cycle Assessment), concluding that the process phases of the plate, its boiling, and its stabilization, are the phases with the greatest impact. Likewise, it is detected that the impacts in all phases are relatively similar (for one kg of net cork produced), although the volumetric difference between these stoppers represents a significant difference in impacts for each unit produced.

scholarly journals Process Modeling and Simulation of Tableting—An Agent-Based Simulation Methodology for Direct Compression

Pharmaceutics ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 996
Author(s):  
Niels Lasse Martin ◽  
Ann Kathrin Schomberg ◽  
Jan Henrik Finke ◽  
Tim Gyung-min Abraham ◽  
Arno Kwade ◽  
...  
Keyword(s):  
Raw Materials ◽  
Pilot Scale ◽  
Physical Models ◽  
Agent Based Simulation ◽  
Validation Data ◽  
Agent Based ◽  
Industrial Processing ◽  
Digital Twins ◽  
Product And Process ◽  
The Impact

In pharmaceutical manufacturing, the utmost aim is reliably producing high quality products. Simulation approaches allow virtual experiments of processes in the planning phase and the implementation of digital twins in operation. The industrial processing of active pharmaceutical ingredients (APIs) into tablets requires the combination of discrete and continuous sub-processes with complex interdependencies regarding the material structures and characteristics. The API and excipients are mixed, granulated if required, and subsequently tableted. Thereby, the structure as well as the properties of the intermediate and final product are influenced by the raw materials, the parametrized processes and environmental conditions, which are subject to certain fluctuations. In this study, for the first time, an agent-based simulation model is presented, which enables the prediction, tracking, and tracing of resulting structures and properties of the intermediates of an industrial tableting process. Therefore, the methodology for the identification and development of product and process agents in an agent-based simulation is shown. Implemented physical models describe the impact of process parameters on material structures. The tablet production with a pilot scale rotary press is experimentally characterized to provide calibration and validation data. Finally, the simulation results, predicting the final structures, are compared to the experimental data.

scholarly journals Modified Nanoclays/Straw Fillers as Functional Additives of Natural Rubber Biocomposites

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 799
Author(s):  
Justyna Miedzianowska ◽  
Marcin Masłowski ◽  
Przemysław Rybiński ◽  
Krzysztof Strzelec
Keyword(s):  
Natural Rubber ◽  
Raw Materials ◽  
Research Work ◽  
Damping Properties ◽  
Main Research ◽  
Functional Additives ◽  
Different Types ◽  
Elastomeric Materials ◽  
Research Goal ◽  
The Impact

Increasingly, raw materials of natural origin are used as fillers in polymer composites. Such biocomposites have satisfactory properties. To ensure above-average functional properties, modifications of biofillers with other materials are also used. The presented research work aimed to produce and characterize elastomeric materials with a straw-based filler and four different types of montmorillonite. The main research goal was to obtain improved functional parameters of vulcanizates based on natural rubber. A series of composites filled with straw and certain types of modified and unmodified nano-clays in various ratios and amounts were prepared. Then, they were subjected to a series of tests to assess the impact of the hybrids used on the final product. It has been shown that the addition of optimal amounts of biofillers can, inter alia, increase the tensile strength of the composite, improve damping properties, extend the burning time of the material and affect the course of vulcanization or cross-linking density.

scholarly journals Sustainability of Extraction of Raw Material by a Combination of Mobile and Stationary Mining Machines and Optimization of Machine Life Cycle

2020 ◽  
Vol 12 (24) ◽  
pp. 10454
Author(s):  
Katarína Teplická ◽  
Martin Straka
Keyword(s):  
Life Cycle ◽  
Raw Materials ◽  
Simulation Method ◽  
Raw Material ◽  
Optimal Distribution ◽  
Transport Costs ◽  
Scientific Discussion ◽  
Mining Companies ◽  
Conveyor Belts ◽  
The Impact

This article summarizes the arguments within the scientific discussion on the issue of using mining machines and their life cycle. The main goal of the article is to investigate the impact of a combination of mobile and stationary mining machines and their optimal distribution in the mining process to increase the efficiency of mining and processing of raw materials. The following methods of research were focused on the use of technical indicators for the valuation efficiency of the mining process: a simulation method was used for the distribution of mining machines, comparison analysis was used for the real and past state of mining machines, and a decision tree was used as managerial instrument for optimal alternatives of mining machines. The research empirically confirms and theoretically proves that optimal distribution of mining machines and machine parks is very important for mining companies. The benefit of this research for the mining company was the new location of the machines and the combination of stationary production lines and mobile equipment. The optimal layout of the machines reduced the number of conveyor belts and improved the transfer of limestone processing to mobile devices, saving time, which was reflected in transport costs. The results can be useful for other mining companies seeking to create an optimal machine park.

Sign in / Sign up

Export Citation Format

Share Document