Effects of Surface Roughness on Rebound Strength in Particle-Wall Collisions in Air and Liquids

2005 ◽  
Author(s):  
Y. Q. Nguyen ◽  
John C. Wells
Keyword(s):  
Surface Roughness ◽  
Qualitative Agreement ◽  
Rough Surfaces ◽  
Tap Water ◽  
Stokes Number ◽  
Glass Beads ◽  
Smooth Surfaces ◽  
Sugar Water ◽  
Glass Plates ◽  
The Impact

Experiments to examine the effects of surface roughness on the strength of rebounds from particle-wall collisions, in liquids and in air, are presented. The target walls are glass plates and have three different values of surface roughness: less than 0.3 μm, 10.5 μm, and 40.1 μm. Particles are glass beads with diameters from 1.05mm to 2.35mm. The experiments are conducted in tap water, sugar-water, and in air. Pre-impact Stokes numbers in liquids are in the range 20–170. For impacts in air, no significant effect of the surface roughness on rebound velocity is observed. In liquids, rough surfaces yield stronger rebounds than smooth surfaces. For a given ratio of surface roughness/particle’s radius, the enhancement of the surface roughness on the rebound compared to the smooth one increases when the impact Stokes number decreases toward the “rebound threshold”. These observations are in qualitative agreement with suggestions in the literature.

Arachidonic Acid and Prostaglandin E2 Influence Human Osteoblast (MG63) Response to Titanium Surface Roughness

2008 ◽  
Vol 34 (6) ◽  
pp. 303-312 ◽  
Author(s):  
David D. Dean ◽  
Casey M. Campbell ◽  
Scott F. Gruwell ◽  
John W. M. Tindall ◽  
Hui-Hsiu Chuang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Arachidonic Acid ◽  
Thymidine Incorporation ◽  
Specific Activity ◽  
Rough Surfaces ◽  
Cell Number ◽  
Smooth Surfaces ◽  
Implant Surface ◽  
Implant Placement ◽  
Effect Of Treatment

Abstract Prior studies have shown that implant surface roughness affects osteoblast proliferation, differentiation, matrix synthesis, and local factor production. Further, cell response is modulated by systemic factors, such as 1,25(OH)2D3 and estrogen as well as mechanical forces. Based on the fact that peri-implant bone healing occurs in a site containing elevated amounts of prostaglandin E2 (PGE2), the hypothesis of the current study is that PGE2 and arachidonic acid (AA), the substrate used by cyclooxygenase to form PGE2, influence osteoblast response to implant surface roughness. To test this hypothesis, 4 different types of commercially pure titanium (cpTi) disks with surfaces of varying roughness (smooth Ti, Ra 0.30 μm; smooth and acid etched Ti [SAE Ti], Ra 0.40 μm; rough Ti, Ra 4.3 μm; rough and acid etched Ti [RAE Ti], Ra 4.15μm) were prepared. MG63 osteoblasts were seeded onto the surfaces, cultured to confluence, and then treated for the last 24 hours of culture with AA (0, 0.1, 1, and 10 nM), PGE2 (0, 1, 10, 25, and 100 nM), or the general cyclooxygenase inhibitor indomethacin (0 or 100 nM). At harvest, the effect of treatment on cell proliferation was assessed by measuring cell number and [3H]-thymidine incorporation, and the effect on cell differentiation was determined by measuring alkaline phosphatase (ALP) specific activity. The effect of AA and PGE2 on cell number was somewhat variable but showed a general decrease on plastic and smooth surfaces and an increase on rough surfaces. In contrast, [3H]-thymidine incorporation was uniformly decreased with treatment on all surfaces. ALP demonstrated the most prominent effect of treatment. On smooth surfaces, AA and PGE2 dose-dependently increased ALP, while on rough surfaces, treatment dose-dependently decreased enzyme specific activity. Indomethacin treatment had either no effect or a slightly inhibitory effect on [3H]-thymidine incorporation on all surfaces. In contrast, indomethacin inhibited ALP on smooth surfaces and stimulated ALP on rough. Taken together, the results indicate that both AA and PGE2 influence osteoblast response by promoting osteoblast differentiation on smooth surfaces, while inhibiting it on rough surfaces. Because implants with rough surfaces are acknowledged to be superior to those with smooth surfaces, these results suggest that use of nonsterioidal anti-inflammatory drugs to block PGE2 production and reduce inflammation may be beneficial in the postoperative period after implant placement. They also indicate that manipulation of the AA metabolic pathway may offer a new therapeutic approach for modulating bone healing after implant placement. Because peri-implant healing takes place in a complex cellular environment quite different from the one used in the present study, additional work will be necessary to substantiate these possibilities.

scholarly journals A comparison of tarsal morphology and traction force in the two burying beetles Nicrophorus nepalensis and Nicrophorus vespilloides (Coleoptera, Silphidae)

2019 ◽  
Vol 10 ◽  
pp. 47-61 ◽  
Author(s):  
Liesa Schnee ◽  
Benjamin Sampalla ◽  
Josef K Müller ◽  
Oliver Betz
Keyword(s):  
Rough Surfaces ◽  
Traction Force ◽  
Interspecific Difference ◽  
Smooth Surfaces ◽  
Burying Beetle ◽  
Surface Polarity ◽  
Traction Forces ◽  
Interspecific Differences ◽  
Friction Performance ◽  
The Impact

Our aim was to compare friction and traction forces between two burying beetle species of the genus Nicrophorus exhibiting different attachment abilities during climbing. Specifically, the interaction of adhesive hairs and claws during attachment with respect to various surface properties was investigated by using a 2 × 3 experimental design. Traction force was measured for two different surface energies (hydrophilic vs hydrophobic) varying in roughness from smooth to micro-rough to rough. Nanotribometric tests on single legs were also performed. The external morphology of the attachment devices investigated by scanning electron microscopy suggested higher intra-specific (intersexual) than inter-specific differences. Whereas differences between the two species in traction force were high on smooth surfaces, no differences could be detected between males and females within each species. With claws intact, both species showed the highest forces on rough surfaces, although N. nepalensis with clipped claws performed best on a smooth surface. However, N. nepalensis beetles outperformed N. vespilloides, which showed no differences between smooth and rough surfaces with clipped claws. Both species demonstrated poor traction forces on micro-rough surfaces. Results concerning the impact of surface polarity were inconclusive, whereas roughness more strongly affected the attachment performance in both species. Nanotribometric analyses of the fore tarsi performed on micro-rough and rough surfaces revealed higher friction in the proximal (pull) direction compared with the distal (push) direction. In these experiments, we detected neither differences in friction performance between the two species, nor clear trends concerning the influence of surface polarity. We conclude that the investigated morphological traits are not critical for the observed interspecific difference in attachment ability on smooth surfaces. Furthermore, interspecific differences in performance are only clear on smooth surfaces and vanish on micro-rough and rough surfaces. Our results suggest that even subtle differences in the adhesion-mediating secretion in closely related species might result in qualitative performance shifts.

Effect of Surface Roughness on the Adhesion of Elastomers to Hard Surfaces

2010 ◽  
Vol 662 ◽  
pp. 39-51 ◽  
Author(s):  
Keith Fuller
Keyword(s):  
Surface Roughness ◽  
Rough Surfaces ◽  
Theoretical Work ◽  
Contact System ◽  
Contact Theory ◽  
Smooth Surfaces ◽  
Rigid Substrate ◽  
Recent Theoretical Work ◽  
Effect Of Surface

The work presented started with the aim of trying to explain why clean smooth surfaces of materials such as metals brought gently into contact show no adhesion. The observation by Johnson Kendall & Roberts of adhesion between smooth surfaces of an elastomeric hemisphere and a rigid substrate suggested a model contact system with which the effect of surface roughness could be investigated experimentally. Moreover the Johnson-Kendal-Roberts (JKR) contact theory could be used to predict the effect of roughness on adhesion. The observations and predictions obtained are compared, and the implications for the contact of two rigid materials outlined. The limitations of the validity of the predictions are mentioned. Further studies of the adhesion to rough surfaces, in particular the phenomenon of enhanced adhesion at low roughness, will be discussed. Finally, more recent theoretical work is briefly referred to.

Experimental Investigation of Interstitial Fluid Effects on Particle Fluctuating Motion

2005 ◽  
Author(s):  
K. Hadinoto ◽  
J. Sinclair Curtis
Keyword(s):  
Interstitial Fluid ◽  
Stokes Number ◽  
Coefficient Of Restitution ◽  
Glass Beads ◽  
Viscous Force ◽  
Fluid Viscosity ◽  
Particle Collisions ◽  
Turbulence Modulation ◽  
Mass Flowrate ◽  
The Impact

The importance of interstitial fluid effects on particle fluctuating motion in gas-particle or liquid-particle flows with significant particle-particle collisions can be characterized by the ratio of the coefficient of restitution for inelastic particle-particle collisions in a fluid ef to the coefficient of restitution for collisions in a vacuum es. In previous research, the ratio ef/es has been found to depend on the impact Stokes number St, which relates the particle inertia to the viscous force. The value of the impact Stokes number is known to be a function of the particle velocity at impact, the size and density of the particle, and the fluid viscosity. In the present work, the effect of the interstitial fluid on particle fluctuating motion is investigated experimentally using LDV/PDPA in a vertical pipe flow configuration. The influence of the variation in the particle loading and Reynolds number, which affects the particle impact velocity and, hence, ef, is probed using particles of two different densities with comparable sizes. Specifically, the downward flow of 70 micron glass beads (density = 2500 kg/m3) and 60 micron hollow ceramic microspheres (density = 700 kg/m3) is investigated for solids loadings (ratio of solids mass flowrate to gas mass flowrate) from 0.4 to 7 and Reynolds numbers which vary from 6000 to 13,000. For this range of conditions, the values for ef range between 0.65 and 0.94 (0.94 is the value for es for glass beads colliding in a vacuum). Trends in the mean and fluctuating velocities for both the gas and particle phases, as well as the gas turbulence modulation in the presence of particles, are discussed in relation to the degree of influence of the interstitial fluid on the details of the particle motion.

Effect of Altering the Sequence of Chempolishing and Electropolishing on Surface Properties of Additively Manufactured (AM) 316 Steel Components

2020 ◽  
Author(s):  
Joshua Dillard ◽  
Andrew Grizzle ◽  
Wondwosen Demisse ◽  
Pawan Tyagi ◽  
Lucas Rice ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Water Contact Angle ◽  
Protective Coatings ◽  
Rough Surfaces ◽  
Stress Raiser ◽  
Internal Surface ◽  
Surface Finishing ◽  
Water Contact ◽  
The Impact

Abstract The surface roughness of as produced additively manufactured (AM) components is very high and may lead to component failure and undesirable coefficients of friction. In rough surfaces, small cracks form at regions of high surface roughness acting as a stress raiser or crack nucleation sites. Likewise, rough surfaces impact both static and kinetic friction that can impede desired motion and oppose desired mechanical forces. For using these components in many applications, it is necessary to reduce surface deviations drastically during postprocessing. For parts with complex geometries and enormous internal surface areas, this reduction presents a complex engineering problem. We have explored chempolishing (C) and electropolishing (E) to reduce the external and internal surface roughness of stainless-steel components in our previous studies. Chempolishing is an electroless etching process that can uniformly smoothen the accessible surfaces of complex AM components. Electropolishing can produce an extremely smooth surface to sub-micrometer level roughness. Our prior work showed that chempolishing and electropolishing produced very distinct surface microstructures. It is quite possible that in future surface finishing, chempolishing and electropolishing may be applied on the same AM component to reduce the surface roughness of complex AM components. The resulting microstructure after the sequential application of chempolishing and electropolishing may be quite different as compared to that of after chempolishing or electropolishing alone. Here, we report the application of altering the sequence of chempolishing and electropolishing to reduce the external and internal surface roughness of 316 steel components. It is unknown what will be the impact of manipulating the sequence of electropolishing and chemical polishing on surface roughness and microstructure of AM materials. This paper focuses on the post-process sequencing of chempolishing, followed by electropolishing (CE) and vice versa (EC). We found chempolishing followed by electropolishing reduced internal surface roughness by as much as 12 micrometers. Whereas the electropolishing followed by chempolishing reduced external surface roughness by an average of ∼15 micrometers. The structure and properties of the surface finished pieces were examined using: Scanning Electron Microscopy (SEM), Surface Profilometry, and Water Contact Angle Measurement. SEM provided direct insight that CE and EC process produced significantly different microstructures from each other and also from chempolished and electropolished processes. Water contact angle measurements performed on CE, and EC treated AM samples showed that surface energy was quite different. Hence, CE and EC are expected to perform quite differently under a corrosive environment and also yield various adhesion quality for the protective coatings. Confirmation of structural changes provided in this experiment shed light on the capabilities of postprocessing improvements we can make to materials performance.

scholarly journals Smoothing additive manufactured parts using ns-pulsed laser radiation

2021 ◽  
Author(s):  
Florian Kuisat ◽  
Fernando Lasagni ◽  
Andrés Fabián Lasagni
Keyword(s):  
Surface Roughness ◽  
Mechanical Performance ◽  
State Of The Art ◽  
Pulsed Laser ◽  
Industrial Applications ◽  
Laser Source ◽  
Pulsed Laser Radiation ◽  
Current State ◽  
The Impact

AbstractIt is well known that the surface topography of a part can affect its mechanical performance, which is typical in additive manufacturing. In this context, we report about the surface modification of additive manufactured components made of Titanium 64 (Ti64) and Scalmalloy®, using a pulsed laser, with the aim of reducing their surface roughness. In our experiments, a nanosecond-pulsed infrared laser source with variable pulse durations between 8 and 200 ns was applied. The impact of varying a large number of parameters on the surface quality of the smoothed areas was investigated. The results demonstrated a reduction of surface roughness Sa by more than 80% for Titanium 64 and by 65% for Scalmalloy® samples. This allows to extend the applicability of additive manufactured components beyond the current state of the art and break new ground for the application in various industrial applications such as in aerospace.

scholarly journals Polyphenol Profiling of Chestnut Pericarp, Integument and Curing Water Extracts to Qualify These Food By-Products as a Source of Antioxidants

Molecules ◽  
2021 ◽  
Vol 26 (8) ◽  
pp. 2335
Author(s):  
Gabriella Pinto ◽  
Sabrina De Pascale ◽  
Maria Aponte ◽  
Andrea Scaloni ◽  
Francesco Addeo ◽  
...  
Keyword(s):  
Mass Spectrometry ◽  
Negative Impact ◽  
Tap Water ◽  
Time Of Flight ◽  
The Other ◽  
Curing Process ◽  
Flight Mass Spectrometry ◽  
Water Curing ◽  
The Impact ◽  
By Products

Plant polyphenols have beneficial antioxidant effects on human health; practices aimed at preserving their content in foods and/or reusing food by-products are encouraged. The impact of the traditional practice of the water curing procedure of chestnuts, which prevents insect/mould damage during storage, was studied to assess the release of polyphenols from the fruit. Metabolites extracted from pericarp and integument tissues or released in the medium from the water curing process were analyzed by matrix-assisted laser desorption ionization-time of flight-mass spectrometry (MALDI-TOF-MS) and electrospray-quadrupole-time of flight-mass spectrometry (ESI-qTOF-MS). This identified: (i) condensed and hydrolyzable tannins made of (epi)catechin (procyanidins) and acid ellagic units in pericarp tissues; (ii) polyphenols made of gallocatechin and catechin units condensed with gallate (prodelphinidins) in integument counterparts; (iii) metabolites resembling those reported above in the wastewater from the chestnut curing process. Comparative experiments were also performed on aqueous media recovered from fruits treated with processes involving: (i) tap water; (ii) tap water containing an antifungal Lb. pentosus strain; (iii) wastewater from a previous curing treatment. These analyses indicated that the former treatment determines a 6–7-fold higher release of polyphenols in the curing water with respect to the other ones. This event has a negative impact on the luster of treated fruits but qualifies the corresponding wastes as a source of antioxidants. Such a phenomenon does not occur in wastewater from the other curing processes, where the release of polyphenols was reduced, thus preserving the chestnut’s appearance. Polyphenol profiling measurements demonstrated that bacterial presence in water hampered the release of pericarp metabolites. This study provides a rationale to traditional processing practices on fruit appearance and qualifies the corresponding wastes as a source of bioactive compounds for other nutraceutical applications.

scholarly journals Photocatalytic Degradation of Sulfolane Using a LED-Based Photocatalytic Treatment System

Catalysts ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 624
Author(s):  
Sripriya Dharwadkar ◽  
Linlong Yu ◽  
Gopal Achari
Keyword(s):  
Photocatalytic Degradation ◽  
Oil And Gas ◽  
Light Emitting Diode ◽  
Tap Water ◽  
Aqueous Media ◽  
Ultrapure Water ◽  
Light Emitting ◽  
Degradation Rates ◽  
Reduced Graphene ◽  
The Impact

Sulfolane is an emerging industrial pollutant detected in the environments near many oil and gas plants in North America. So far, numerous advanced oxidation processes have been investigated to treat sulfolane in aqueous media. However, there is only a few papers that discuss the degradation of sulfolane using photocatalysis. In this study, photocatalytic degradation of sulfolane using titanium dioxide (TiO2) and reduced graphene oxide TiO2 composite (RGO-TiO2) in a light-emitting diode (LED) photoreactor was investigated. The impact of different waters (ultrapure water, tap water, and groundwater) and type of irradiation (UVA-LED and mercury lamp) on photocatalytic degradation of sulfolane were also studied. In addition, a reusability test was conducted for the photocatalyst to examine the degradation of sulfolane in three consecutive cycles with new batches of sulfolane-contaminated water. The results show that LED-based photocatalysis was effective in degrading sulfolane in waters even after three photocatalytic cycles. UVA-LEDs displayed more efficient use of photon energy when compared with the mercury lamps as they have a narrow emission spectrum coinciding with the absorption of TiO2. The combination of UVA-LED and TiO2 yielded better performance than UVA-LED and RGO-TiO2 for the degradation of sulfolane. Much lower sulfolane degradation rates were observed in tap water and groundwater than ultrapure water.

Nature instigated Grey wolf algorithm for parametric optimization during machining (Milling) of polymer nanocomposites

2021 ◽  
pp. 089270572199320
Author(s):  
Prakhar Kumar Kharwar ◽  
Rajesh Kumar Verma
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Polymer Nanocomposites ◽  
Feed Rate ◽  
Fitness Function ◽  
Depth Of Cut ◽  
Multiwall Carbon Nanotube ◽  
Grey Wolf ◽  
Milling Characteristics ◽  
The Impact

The new era of engineering society focuses on the utilization of the potential advantage of carbon nanomaterials. The machinability facets of nanocarbon materials are passing through an initial stage. This article emphasizes the machinability evaluation and optimization of Milling performances, namely Surface roughness (Ra), Cutting force (Fc), and Material removal rate (MRR) using a recently developed Grey wolf optimization algorithm (GWOA). The Taguchi theory-based L27 orthogonal array (OA) was employed for the Machining (Milling) of polymer nanocomposites reinforced by Multiwall carbon nanotube (MWCNT). The second-order polynomial equation was intended for the analysis of the model. These mathematical models were used as a fitness function in the GWOA to predict machining performances. The ANOVA outcomes efficiently explore the impact of machine parameters on Milling characteristics. The optimal combination for lower surface roughness value is 1.5 MWCNT wt.%, 1500 rpm of spindle speed, 50 mm/min of feed rate, and 3 mm depth of cut. For lower cutting force, 1.0 wt.%, 1500 rpm, 90 mm/min feed rate and 1 mm depth of cut and the maximize MRR was acquired at 0.5 wt.%, 500 rpm, 150 mm/min feed rate and 3 mm depth of cut. The deviation of the predicted value from the experimental value of Ra, Fc, and MRR are found as 2.5, 6.5 and 5.9%, respectively. The convergence plot of all Milling characteristics suggests the application potential of the GWO algorithm for quality improvement in a manufacturing environment.

Sign in / Sign up

Export Citation Format

Share Document