scholarly journals Flow analysis of a set of ornamental chimney caps designed by Antoni Gaudí

2020 ◽  
Vol 8 (1) ◽  
Author(s):  
Albert Samper ◽  
Jordi Iglesias ◽  
Blas Herrera ◽  
Jordi Pallares
Keyword(s):  
Theoretical Model ◽  
Flow Analysis ◽  
External Flow ◽  
Pressure Reduction ◽  
Simple Theoretical Model ◽  
Wide Range ◽  
Wind Tunnel Measurements ◽  
The Individual ◽  
Antoni Gaudí ◽  
Flow Velocities

AbstractWe analyzed theoretically and experimentally the performance of the 19 different ornamental caps of the individual chimneys located on the terrace of Palau Güell (Barcelona, Spain) designed by Antoni Gaudí. This set of chimney caps has wide range of external geometries and different number and shapes of openings. Models of the chimney caps were obtained using photogrammetry and 3D printing. Wind tunnel measurements of the pressure inside the stack pipe connected to the cap were performed for different external and stack flow velocities. Two distinct orientations of the external flow with respect to the chimneys were considered. We derived a simple theoretical model, based on the potential flow theory, to relate the non-dimensional pressure reduction in the stack (chimney draft) with the ratio between the external and stack flow velocities. It has been found that the behavior of the chimneys caps predicted by this model is in agreement with the measurements. It has been found that the performance of the chimneys depends mainly on the number of supports of the conical cover of the cap and it is essentially independent on the shape of the cap and on the number and geometry of the openings located on the cap. These conclusions obtained for this particular set of chimneys can be useful for the design of caps for ornamental or general use.

Pneumatic Rupture of a Brittle Pipe: The Depressurization Transient Adjacent to the Ruptured Zone

1981 ◽  
Vol 103 (3) ◽  
pp. 287-293 ◽  
Author(s):  
M. R. Baum ◽  
M. J. H. Elston
Keyword(s):  
Theoretical Model ◽  
Rupture Zone ◽  
Bursting Pressure ◽  
Pressure Transient ◽  
Adjacent Section ◽  
Comparison With Experiment ◽  
Simple Theoretical Model ◽  
Wide Range ◽  
Predicted Values

A simple theoretical model is developed to predict the pressure transient within a gas-pressurized pipe when an adjacent section shatters into many fragments. Comparison with experiment shows that the model correctly predicts the general form of the transient over a wide range of bursting pressure and rupture zone lengths, though the measured initial depressurization rates all fall below the predicted values.

THE VALUE OF LOVE IN THE SYSTEM OF FORMATION OF THE PROFESSIONAL MATURITY OF THE EDUCATOR

2020 ◽  
Vol 1 (10(79)) ◽  
pp. 12-18
Author(s):  
G. Bubyreva
Keyword(s):  
Russian Federation ◽  
The State ◽  
Educational Process ◽  
Wide Range ◽  
The Family ◽  
The Russian Federation ◽  
The Government ◽  
The Individual ◽  
The Right

The existing legislation determines the education as "an integral and focused process of teaching and upbringing, which represents a socially important value and shall be implemented so as to meet the interests of the individual, the family, the society and the state". However, even in this part, the meaning of the notion ‘socially significant benefit is not specified and allows for a wide range of interpretation [2]. Yet the more inconcrete is the answer to the question – "who and how should determine the interests of the individual, the family and even the state?" The national doctrine of education in the Russian Federation, which determined the goals of teaching and upbringing, the ways to attain them by means of the state policy regulating the field of education, the target achievements of the development of the educational system for the period up to 2025, approved by the Decree of the Government of the Russian Federation of October 4, 2000 #751, was abrogated by the Decree of the Government of the Russian Federation of March 29, 2014 #245 [7]. The new doctrine has not been developed so far. The RAE Academician A.B. Khutorsky believes that the absence of the national doctrine of education presents a threat to national security and a violation of the right of citizens to quality education. Accordingly, the teacher has to solve the problem of achieving the harmony of interests of the individual, the family, the society and the government on their own, which, however, judging by the officially published results, is the task that exceeds the abilities of the participants of the educational process.  The particular concern about the results of the patriotic upbringing served as a basis for the legislative initiative of the RF President V. V. Putin, who introduced the project of an amendment to the Law of RF "About Education of the Russian Federation" to the State Duma in 2020, regarding the quality of patriotic upbringing [3]. Patriotism, considered by the President of RF V. V. Putin as the only possible idea to unite the nation is "THE FEELING OF LOVE OF THE MOTHERLAND" and the readiness for every sacrifice and heroic deed for the sake of the interests of your Motherland. However, the practicing educators experience shortfalls in efficient methodologies of patriotic upbringing, which should let them bring up citizens, loving their Motherland more than themselves. The article is dedicated to solution to this problem based on the Value-sense paradigm of upbringing educational dynasty of the Kurbatovs [15].

Punk as Folk: Continuities and Tensions in the UK and Beyond

2020 ◽  
Author(s):  
Pete Dale
Keyword(s):  
Folk Music ◽  
Music Making ◽  
Collective Creativity ◽  
Living Tradition ◽  
Wide Range ◽  
The Us ◽  
The Common ◽  
The Individual ◽  
The Uk

Numerous claims have been made by a wide range of commentators that punk is somehow “a folk music” of some kind. Doubtless there are several continuities. Indeed, both tend to encourage amateur music-making, both often have affiliations with the Left, and both emerge at least partly from a collective/anti-competitive approach to music-making. However, there are also significant tensions between punk and folk as ideas/ideals and as applied in practice. Most obviously, punk makes claims to a “year zero” creativity (despite inevitably offering re-presentation of at least some existing elements in every instance), whereas folk music is supposed to carry forward a tradition (which, thankfully, is more recognized in recent decades as a subject-to-change “living tradition” than was the case in folk’s more purist periods). Politically, meanwhile, postwar folk has tended more toward a socialist and/or Marxist orientation, both in the US and UK, whereas punk has at least rhetorically claimed to be in favor of “anarchy” (in the UK, in particular). Collective creativity and competitive tendencies also differ between the two (perceived) genre areas. Although the folk scene’s “floor singer” tradition offers a dispersal of expressive opportunity comparable in some ways to the “anyone can do it” idea that gets associated with punk, the creative expectation of the individual within the group differs between the two. Punk has some similarities to folk, then, but there are tensions, too, and these are well worth examining if one is serious about testing out the common claim, in both folk and punk, that “anyone can do it.”

scholarly journals Incumbent and Entrant Bidding in Scoring Rule Auctions: A Study on Italian Canteen Services

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Riccardo Camboni ◽  
Paola Valbonesi
Keyword(s):  
Theoretical Model ◽  
Production Cost ◽  
Specific Information ◽  
Scoring Rule ◽  
The Public ◽  
Simple Theoretical Model ◽  
Original Dataset

AbstractWe empirically investigate incumbents’ and entrants’ bids on an original dataset of 192 scoring rule auctions for canteen services in Italy. Our findings show that winning rebates are lower (i.e., prices paid by the public buyer are higher) when the contract is awarded to the incumbent supplier. This result is not explained by the observable characteristics of the auction or the service awarded. We develop a simple theoretical model showing that the result is consistent with a setting in which the buyer exploits specific information on the incumbent supplier’s production cost.

scholarly journals The OsERF115/AP2EREBP110 Transcription Factor Is Involved in the Multiple Stress Tolerance to Heat and Drought in Rice Plants

2021 ◽  
Vol 22 (13) ◽  
pp. 7181
Author(s):  
Seong-Im Park ◽  
Hyeok Jin Kwon ◽  
Mi Hyeon Cho ◽  
Ji Sun Song ◽  
Beom-Gi Kim ◽  
...  
Keyword(s):  
Stress Tolerance ◽  
Transcriptional Activation ◽  
Individual Plant ◽  
Hormone Signaling ◽  
Combined Stress ◽  
Drought Treatment ◽  
Wide Range ◽  
The Individual ◽  
Potential Use ◽  
Multiple Stress Tolerance

The AP2/EREBP family transcription factors play important roles in a wide range of stress tolerance and hormone signaling. In this study, a heat-inducible rice ERF gene was isolated and functionally characterized. The OsERF115/AP2EREBP110 was categorized to Group-IIIc of the rice AP2/EREBP family and strongly induced by heat and drought treatment. The OsERF115/AP2EREBP110 protein targeted to nuclei and suppressed the ABA-induced transcriptional activation of Rab16A promoter in rice protoplasts. Overexpression of OsERF115/AP2EREBP110 enhanced thermotolerance of seeds and vegetative growth stage plants. The OsERF115/AP2EREBP110 overexpressing (OE) plants exhibited higher proline level and increased expression of a proline biosynthesis P5CS1 gene. Phenotyping of water use dynamics of the individual plant indicates that the OsERF115/AP2EREBP110-OE plant exhibited better water saving traits under heat and drought combined stress. Our combined results suggest the potential use of OsERF115/AP2EREBP110 as a candidate gene for genetic engineering approaches to develop heat and drought stress-tolerant crops.

scholarly journals Entangling Lattice-Trapped Bosons with a Free Impurity: Impact on Stationary and Dynamical Properties

Entropy ◽  
2021 ◽  
Vol 23 (3) ◽  
pp. 290
Author(s):  
Maxim Pyzh ◽  
Kevin Keiler ◽  
Simeon I. Mistakidis ◽  
Peter Schmelcher
Keyword(s):  
Structural Changes ◽  
Many Body ◽  
Wide Range ◽  
Entropy Measures ◽  
Particle Level ◽  
The Many ◽  
The One ◽  
Tunneling Dynamics ◽  
The Individual ◽  
Trapped Bosons

We address the interplay of few lattice trapped bosons interacting with an impurity atom in a box potential. For the ground state, a classification is performed based on the fidelity allowing to quantify the susceptibility of the composite system to structural changes due to the intercomponent coupling. We analyze the overall response at the many-body level and contrast it to the single-particle level. By inspecting different entropy measures we capture the degree of entanglement and intraspecies correlations for a wide range of intra- and intercomponent interactions and lattice depths. We also spatially resolve the imprint of the entanglement on the one- and two-body density distributions showcasing that it accelerates the phase separation process or acts against spatial localization for repulsive and attractive intercomponent interactions, respectively. The many-body effects on the tunneling dynamics of the individual components, resulting from their counterflow, are also discussed. The tunneling period of the impurity is very sensitive to the value of the impurity-medium coupling due to its effective dressing by the few-body medium. Our work provides implications for engineering localized structures in correlated impurity settings using species selective optical potentials.

scholarly journals A Tale of Odds and Ratios: Political Preference Formation in Postindustrial Democracies

2021 ◽  
Author(s):  
David M. Wineroither ◽  
Rudolf Metz
Keyword(s):  
Social Stratification ◽  
Political Process ◽  
Environment Interaction ◽  
Preference Formation ◽  
Political Preference ◽  
Individual Level ◽  
Gene Environment Interaction ◽  
Gene Environment ◽  
Wide Range ◽  
The Individual

AbstractThis report surveys four approaches that are pivotal to the study of preference formation: (a) the range, validity, and theoretical foundations of explanations of political preferences at the individual and mass levels, (b) the exploration of key objects of preference formation attached to the democratic political process (i.e., voting in competitive elections), (c) the top-down vs. bottom-up character of preference formation as addressed in leader–follower studies, and (d) gene–environment interaction and the explanatory weight of genetic predisposition against the cumulative weight of social experiences.In recent years, our understanding of sites and processes of (individual) political-preference formation has substantially improved. First, this applies to a greater variety of objects that provide fresh insight into the functioning and stability of contemporary democracy. Second, we observe the reaffirmation of pivotal theories and key concepts in adapted form against widespread challenge. This applies to the role played by social stratification, group awareness, and individual-level economic considerations. Most of these findings converge in recognising economics-based explanations. Third, research into gene–environment interplay rapidly increases the number of testable hypotheses and promises to benefit a wide range of approaches already taken and advanced in the study of political-preference formation.

scholarly journals Design of Personalized Devices—The Tradeoff between Individual Value and Personalization Workload

2020 ◽  
Vol 11 (1) ◽  
pp. 241
Author(s):  
Juliane Kuhl ◽  
Andreas Ding ◽  
Ngoc Tuan Ngo ◽  
Andres Braschkat ◽  
Jens Fiehler ◽  
...  
Keyword(s):  
Customer Value ◽  
Early Stage ◽  
Treatment Success ◽  
Product Family ◽  
Flow Diverter ◽  
New Method ◽  
Product Families ◽  
Wide Range ◽  
The Individual ◽  
Individual Value

Personalized medical devices adapted to the anatomy of the individual promise greater treatment success for patients, thus increasing the individual value of the product. In order to cater to individual adaptations, however, medical device companies need to be able to handle a wide range of internal processes and components. These are here referred to collectively as the personalization workload. Consequently, support is required in order to evaluate how best to target product personalization. Since the approaches presented in the literature are not able to sufficiently meet this demand, this paper introduces a new method that can be used to define an appropriate variety level for a product family taking into account standardized, variant, and personalized attributes. The new method enables the identification and evaluation of personalizable attributes within an existing product family. The method is based on established steps and tools from the field of variant-oriented product design, and is applied using a flow diverter—an implant for the treatment of aneurysm diseases—as an example product. The personalization relevance and adaptation workload for the product characteristics that constitute the differentiating product properties were analyzed and compared in order to determine a tradeoff between customer value and personalization workload. This will consequently help companies to employ targeted, deliberate personalization when designing their product families by enabling them to factor variety-induced complexity and customer value into their thinking at an early stage, thus allowing them to critically evaluate a personalization project.

scholarly journals Market Choices Driven by Reference Groups: A Comparison of Analytical and Simulation Results on Random Networks

Entropy ◽  
2021 ◽  
Vol 23 (8) ◽  
pp. 1007
Author(s):  
Michał Ramsza
Keyword(s):  
Theoretical Model ◽  
Reference Group ◽  
Third Party ◽  
Qualitative Behavior ◽  
Reference Groups ◽  
Group Influence ◽  
Simple Theoretical Model ◽  
High Connectivity ◽  
Simulation Results ◽  
Two Equilibria

The present paper reports simulation results for a simple model of reference group influence on market choices, e.g., brand selection. The model was simulated on three types of random graphs, Erdos–Renyi, Barabasi–Albert, and Watts–Strogatz. The estimates of equilibria based on the simulation results were compared to the equilibria of the theoretical model. It was verified that the simulations exhibited the same qualitative behavior as the theoretical model, and for graphs with high connectivity and low clustering, the quantitative predictions offered a viable approximation. These results allowed extending the results from the simple theoretical model to networks. Thus, by increasing the positive response towards the reference group, the third party may create a bistable situation with two equilibria at which respective brands dominate the market. This task is easier for large reference groups.

ExpanDrogram: Dynamic Visualization of Big Data Segmentation over Time

2021 ◽  
Vol 13 (2) ◽  
pp. 1-27
Author(s):  
A. Khalemsky ◽  
R. Gelbard
Keyword(s):  
Big Data ◽  
Visual Presentation ◽  
Trend Detection ◽  
Dynamic Visualization ◽  
Segmentation Process ◽  
Key Points ◽  
Wide Range ◽  
History Of ◽  
The Individual ◽  
Over Time

In dynamic and big data environments the visualization of a segmentation process over time often does not enable the user to simultaneously track entire pieces. The key points are sometimes incomparable, and the user is limited to a static visual presentation of a certain point. The proposed visualization concept, called ExpanDrogram, is designed to support dynamic classifiers that run in a big data environment subject to changes in data characteristics. It offers a wide range of features that seek to maximize the customization of a segmentation problem. The main goal of the ExpanDrogram visualization is to improve comprehensiveness by combining both the individual and segment levels, illustrating the dynamics of the segmentation process over time, providing “version control” that enables the user to observe the history of changes, and more. The method is illustrated using different datasets, with which we demonstrate multiple segmentation parameters, as well as multiple display layers, to highlight points such as new trend detection, outlier detection, tracking changes in original segments, and zoom in/out for more/less detail. The datasets vary in size from a small one to one of more than 12 million records.

Sign in / Sign up

Export Citation Format

Share Document