scholarly journals Effect of Different Solvent and Ratio Towards Microalgae Oil Production by Ultrasonic Assisted Soxhlet Extraction Techniques

2019 ◽  
Vol 35 (4) ◽  
pp. 1377-1383
Author(s):  
Y.C. Wong ◽  
R. Shahirah
Keyword(s):  
Lipid Content ◽  
Fossil Fuels ◽  
Raw Materials ◽  
Lipid Production ◽  
Soxhlet Extraction ◽  
Oil Production ◽  
Extraction Yield ◽  
Biodiesel Production ◽  
Freshwater Algae ◽  
Algae Oil

Currently, the renewable feedstock is the most needed worldwide. Microalgae are promising raw materials for supplying biofuels due to the depletion of fossil fuels. The microalgae found were mostly consists of freshwater algae. The aim of this research is to study the effect of different solvents and ratio using Soxhlet extraction method. Many parameters were introduced in this study in order to enhance the lipid production of microalgae. Lipid content of algae oil production known as Fatty acid that found was being analyzed. Different solvents used and ratio was expected to have different highest in lipid content. Chloroform, ethanol, and hexane were chosen as the solvents used. The best solvent for lipid production was the combination of different solvents and ratio. Data showed that 8% is the highest total oil extraction yield obtained from combination of chloroform and ethanol with a ratio (1:2). The compound and lipid content in algae oil are analyzed through Gas Chromatography Mass Spectrometer (GC-MS) analysis. Fatty acids have many benefits and also have interest preparation for health products. Green microalgae strain was being identified and cultured as future potential for biodiesel production. Significant of this study is to unveil the benefit of algae oil as sustainable future resources.

scholarly journals The Use of Urea and Kelp Waste Extract is A Promising Strategy for Maximizing the Biomass Productivity and Lipid Content in Chlorella sorokiniana

Plants ◽  
2020 ◽  
Vol 9 (4) ◽  
pp. 463 ◽  
Author(s):  
Ali Nawaz Kumbhar ◽  
Meilin He ◽  
Abdul Razzaque Rajper ◽  
Khalil Ahmed Memon ◽  
Muhammad Rizwan ◽  
...  
Keyword(s):  
Lipid Content ◽  
Fossil Fuels ◽  
Fossil Fuel ◽  
Lipid Production ◽  
Total Lipid Content ◽  
Biomass Productivity ◽  
Chlorella Sorokiniana ◽  
Biofuel Production ◽  
Promising Strategy ◽  
Waste Extract

The decline in fossil fuel reserves has forced researchers to seek out alternatives to fossil fuels. Microalgae are considered to be a promising feedstock for sustainable biofuel production. Previous studies have shown that urea is an important nitrogen source for cell growth and the lipid production of microalgae. The present study investigated the effect of different concentrations of urea combined with kelp waste extract on the biomass and lipid content of Chlorella sorokiniana. The results revealed that the highest cell density, 20.36 × 107 cells−1, and maximal dry biomass, 1.70 g/L, were achieved in the presence of 0.5 g/L of urea combined with 8% kelp waste extract. Similarly, the maximum chlorophyll a, b and beta carotenoid were 10.36 mg/L, 7.05, and 3.01 mg/L, respectively. The highest quantity of carbohydrate content, 290.51 µg/mL, was achieved in the presence of 0.2 g/L of urea and 8% kelp waste extract. The highest fluorescence intensity, 40.05 × 107 cells−1, and maximum total lipid content (30%) were achieved in the presence of 0.1 g/L of urea and 8% kelp waste extract. The current study suggests that the combination of urea and kelp waste extract is the best strategy to enhance the biomass and lipid content in Chlorella sorokiniana.

scholarly journals RAPE SEED OIL TETRAHYDROFURFURYLESTERS

2015 ◽  
Vol 1 ◽  
pp. 46
Author(s):  
K. Malins ◽  
V. Kampars ◽  
R. Kampare ◽  
T. Rusakova
Keyword(s):  
Rapeseed Oil ◽  
Fossil Fuels ◽  
Raw Materials ◽  
Methyl Esters ◽  
Cetane Number ◽  
Food Prices ◽  
Raw Material ◽  
Biodiesel Production ◽  
Cold Filter Plugging Point ◽  
Mineral Oils

The transesterification of vegetable oil using various kinds of alcohols is a simple and efficient renewable fuel synthesis technique. Products obtained by modifying natural triglycerides in transesterification reaction substitute fossil fuels and mineral oils. Currently the most significant is the biodiesel, a mixture of fatty acid methyl esters, which is obtained in a reaction with methanol, which in turn is obtained from fossil raw materials. In biodiesel production it would be more appropriate to use alcohols which can be obtained from renewable local raw materials. Ethanol rouses interest as a possible reagent, however, its production locally is based on the use of grain and therefore competes with food production so it would implicitly cause increase in food prices. Another raw material option is alcohols that can be obtained from furfurole. Furfurole is obtained in dehydration process from pentose sugars which can be extracted from crop straw, husk and other residues of agricultural production. From furfurole the tetrahydrofurfuryl alcohol (THFA), a raw material for biodiesel, can be produced. By transesterifying rapeseed oil with THFA it would be possible to obtain completely renewable biodiesel with properties very close to diesel [2-4]. With the purpose of developing the synthesis of such fuel, in this work a three-stage synthesis of rapeseed oil tetrahydrofurfurylesters (ROTHFE) in sulphuric acid presence has been performed, achieving product with purity over 98%. The most important qualitative factors of ROTHFE have been determined - cold filter plugging point, cetane number, water content, Iodine value, phosphorus content, density, viscosity and oxidative stability.

scholarly journals Extraction Solvents Composition Effect In Biodiesel Production From Microalgae Consortium Botryococcus Braunii And Dunaliella Sp.

Khazanah ◽  
2020 ◽  
Vol 12 (2) ◽  
Author(s):  
Tiara Nur Azizah ◽  
◽  
Alya Putri Ramadhanty ◽  
Nadya Feranika ◽  
◽  
...  
Keyword(s):  
Fossil Fuels ◽  
Production Capacity ◽  
Water Concentration ◽  
Soxhlet Extraction ◽  
Botryococcus Braunii ◽  
Solvent Mixture ◽  
Biodiesel Production ◽  
Solvent Ratio ◽  
Extraction Solvent ◽  
Biodiesel Synthesis

Indonesia has entered an energy emergency phase, proven that Indonesia is no longer a surplus oil producer due to the productivity of the wells decrease over the years and the pattern of people's consumption of fossil fuels has been exceeding the production capacity. Therefore, we need the right solution to overcome this problem, which is developing biodiesel as renewable energy based on microalgae oil. The microalgae used in this research is the consortium of microalgae Botryococcus braunii and Dunaliella sp. Microalgae were cultivated and harvested through the dewatering process with 1 g naoh/1 L water concentration. Water contents of cultivated Botryococcus braunii are 60.2505% while Dunaliella sp. Is 64.5002%. The oil from microalgae is obtained by extracted dry microalgae through the soxhlet extraction (leaching) method with mixed solvent n-hexane and ethanol as the co-solvent using a variety of solvent ratio 2:1 and 3:1. Pure microalgae consortium oil separated from the solvent using the distillation process then analyzed with GC-FID. The analysis result is trans-linoleic acid is the most dominant fatty acid contained in this oil. Transesterification process with cao (1.5% of oil weight) as a catalyst. The results obtained from this study are the oil yield 72% extracted with a solvent mixture of n-hexane and ethanol 2:1 and 60.4% for 3:1. The biodiesel synthesis resulted in the amount of yield obtained from the solvent ratio 2:1 extraction is 94.3%, while with solvent ratio 3:1 is 79.2%. The quality of both biodiesels has met the requirements of SNI 7182:2015 and ASTM D7467, except the density of biodiesel with extraction solvent composition 3:1 which is below the standard. Therefore, the best biodiesel quality is obtained from microalgae consortium’s oil with the composition of extraction solvent 2:1.

Optimization of lipid accumulation in Pleurastrum insigne for biodiesel production

2021 ◽  
Vol 16 (10) ◽  
pp. 144-155
Author(s):  
Van Lal Michael Chhandama ◽  
Belur Kumudini Satyan
Keyword(s):  
Lipid Content ◽  
Lipid Production ◽  
Statistical Design ◽  
High Growth ◽  
High Growth Rate ◽  
Biodiesel Production ◽  
Nitrogen And Phosphorus ◽  
Biodiesel Standards ◽  
High Lipid ◽  
Different Sources

Microalgae emerged as a competent feedstock for biodiesel production because of high growth rate and lipid content. This work focuses on isolation of novel microalgal strain from different sources of water for the production of biodiesel. The isolated microalgae, Pleurastrum insigne possessed high lipid content (~28 % dcw), further optimized to 57.06 % dcw using a statistical design (CCD) under Response Surface Methodology. Lipid production was optimized by nutrient (nitrogen and phosphorus) and pH stress. The different type of fatty acids present in the optimized lipid was also profiled using GCMS. Biodiesel yield was found to be 82.14 % of the total lipid and the fuel properties tested have met IS, ASTM and EN biodiesel standards.

scholarly journals Lipid Extraction fromSpirulinasp. andSchizochytriumsp. Using Supercritical CO2with Methanol

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Shihong Liu ◽  
Husam A. Abu Hajar ◽  
Guy Riefler ◽  
Ben J. Stuart
Keyword(s):  
Organic Solvents ◽  
Methylene Chloride ◽  
Lipid Extraction ◽  
Volume Ratio ◽  
Soxhlet Extraction ◽  
Extraction Process ◽  
Extraction Yield ◽  
Biodiesel Production ◽  
Operating Pressure ◽  
High Lipid

Microalgae are one of the most promising feedstocks for biodiesel production due to their high lipid content and easy farming. However, the extraction of lipids from microalgae is energy intensive and costly and involves the use of toxic organic solvents. Compared with organic solvent extraction, supercritical CO2(SCCO2) has demonstrated advantages through lower toxicity and no solvent-liquid separation. Due to the nonpolar nature of SCCO2, polar organic solvents such as methanol may need to be added as a modifier in order to increase the extraction ability of SCCO2. In this paper, pilot scale lipid extraction using SCCO2was studied on two microalgae species:Spirulinasp. andSchizochytriumsp. For each species, SCCO2extraction was conducted on 200 g of biomass for 6 h. Methanol was added as a cosolvent in the extraction process based on a volume ratio of 4%. The results showed that adding methanol in SCCO2increased the lipid extraction yield significantly for both species. Under an operating pressure of 4000 psi, the lipid extraction yields forSpirulinasp. andSchizochytriumsp. were increased by 80% and 72%, respectively. It was also found that a stepwise addition of methanol was more effective than a one-time addition. In comparison with Soxhlet extraction using methylene chloride/methanol (2:1, v/v), the methanol-SCCO2extraction demonstrated its high effectiveness for lipid extraction. In addition, the methanol-SCCO2system showed a high lipid extraction yield after increasing biomass loading fivefold, indicating good potential for scaling up this method. Finally, a kinetic study of the SCCO2extraction process was conducted, and the results showed that methanol concentration in SCCO2has the strongest influence on the lipid extraction yield.

scholarly journals Conversion of sugar beet residues into lipids by Lipomyces starkeyi for biodiesel production

2020 ◽  
Vol 19 (1) ◽  
Author(s):  
Francesca Martani ◽  
Letizia Maestroni ◽  
Mattia Torchio ◽  
Diletta Ami ◽  
Antonino Natalello ◽  
...  
Keyword(s):  
Sugar Beet ◽  
Lipid Content ◽  
Lipid Production ◽  
Batch Process ◽  
Batch Cultivation ◽  
Biodiesel Production ◽  
Cellular Lipid ◽  
Lipomyces Starkeyi ◽  
Yeast Cultures ◽  
Beet Pulp

Abstract Background Lipids from oleaginous yeasts emerged as a sustainable alternative to vegetable oils and animal fat to produce biodiesel, the biodegradable and environmentally friendly counterpart of petro-diesel fuel. To develop economically viable microbial processes, the use of residual feedstocks as growth and production substrates is required. Results In this work we investigated sugar beet pulp (SBP) and molasses, the main residues of sugar beet processing, as sustainable substrates for the growth and lipid accumulation by the oleaginous yeast Lipomyces starkeyi. We observed that in hydrolysed SBP the yeast cultures reached a limited biomass, cellular lipid content, lipid production and yield (2.5 g/L, 19.2%, 0.5 g/L and 0.08 g/g, respectively). To increase the initial sugar availability, cells were grown in SBP blended with molasses. Under batch cultivation, the cellular lipid content was more than doubled (47.2%) in the presence of 6% molasses. Under pulsed-feeding cultivation, final biomass, cellular lipid content, lipid production and lipid yield were further improved, reaching respectively 20.5 g/L, 49.2%, 9.7 g/L and 0.178 g/g. Finally, we observed that SBP can be used instead of ammonium sulphate to fulfil yeasts nitrogen requirement in molasses-based media for microbial oil production. Conclusions This study demonstrates for the first time that SBP and molasses can be blended to create a feedstock for the sustainable production of lipids by L. starkeyi. The data obtained pave the way to further improve lipid production by designing a fed-batch process in bioreactor. Graphical abstract

scholarly journals Biomass and lipid induction strategies in microalgae for biofuel production and other applications

2019 ◽  
Vol 18 (1) ◽  
Author(s):  
Hossein Alishah Aratboni ◽  
Nahid Rafiei ◽  
Raul Garcia-Granados ◽  
Abbas Alemzadeh ◽  
José Rubén Morones-Ramírez
Keyword(s):  
Lipid Content ◽  
Large Scale ◽  
Fossil Fuels ◽  
Low Cost ◽  
Lipid Production ◽  
Arable Land ◽  
Economic Cost ◽  
Biofuel Production ◽  
Scale Production ◽  
Microalgae Biomass

Abstract The use of fossil fuels has been strongly related to critical problems currently affecting society, such as: global warming, global greenhouse effects and pollution. These problems have affected the homeostasis of living organisms worldwide at an alarming rate. Due to this, it is imperative to look for alternatives to the use of fossil fuels and one of the relevant substitutes are biofuels. There are different types of biofuels (categories and generations) that have been previously explored, but recently, the use of microalgae has been strongly considered for the production of biofuels since they present a series of advantages over other biofuel production sources: (a) they don’t need arable land to grow and therefore do not compete with food crops (like biofuels produced from corn, sugar cane and other plants) and; (b) they exhibit rapid biomass production containing high oil contents, at least 15 to 20 times higher than land based oleaginous crops. Hence, these unicellular photosynthetic microorganisms have received great attention from researches to use them in the large-scale production of biofuels. However, one disadvantage of using microalgae is the high economic cost due to the low-yields of lipid content in the microalgae biomass. Thus, development of different methods to enhance microalgae biomass, as well as lipid content in the microalgae cells, would lead to the development of a sustainable low-cost process to produce biofuels. Within the last 10 years, many studies have reported different methods and strategies to induce lipid production to obtain higher lipid accumulation in the biomass of microalgae cells; however, there is not a comprehensive review in the literature that highlights, compares and discusses these strategies. Here, we review these strategies which include modulating light intensity in cultures, controlling and varying CO2 levels and temperature, inducing nutrient starvation in the culture, the implementation of stress by incorporating heavy metal or inducing a high salinity condition, and the use of metabolic and genetic engineering techniques coupled with nanotechnology.

scholarly journals Exogenous l-proline improved Rhodosporidium toruloides lipid production on crude glycerol

2020 ◽  
Vol 13 (1) ◽  
Author(s):  
Rasool Kamal ◽  
Yuxue Liu ◽  
Qiang Li ◽  
Qitian Huang ◽  
Qian Wang ◽  
...  
Keyword(s):  
Cell Growth ◽  
Lipid Content ◽  
Crude Glycerol ◽  
Oleaginous Yeast ◽  
Lipid Production ◽  
Rhodosporidium Toruloides ◽  
Biodiesel Production ◽  
Lipid Yield ◽  
Stress Agent ◽  
Glycerol Consumption

Abstract Background Crude glycerol as a promising feedstock for microbial lipid production contains several impurities that make it toxic stress inducer at high amount. Under stress conditions, microorganisms can accumulate l-proline as a safeguard. Herein, l-proline was assessed as an anti-stress agent in crude glycerol media. Results Crude glycerol was converted to microbial lipids by the oleaginous yeast Rhodosporidium toruloides CGMCC 2.1389 in a two-staged culture mode. The media was supplied with exogenous l-proline to improve lipid production efficiency in high crude glycerol stress. An optimal amount of 0.5 g/L l-proline increased lipid titer and lipid yield by 34% and 28%, respectively. The lipid titer of 12.2 g/L and lipid content of 64.5% with a highest lipid yield of 0.26 g/g were achieved with l-proline addition, which were far higher than those of the control, i.e., lipid titer of 9.1 g/L, lipid content of 58% and lipid yield of 0.21 g/g. Similarly, l-proline also improved cell growth and glycerol consumption. Moreover, fatty acid compositional profiles of the lipid products was found suitable as a potential feedstock for biodiesel production. Conclusion Our study suggested that exogenous l-proline improved cell growth and lipid production on crude glycerol by R. toruloides. The fact that higher lipid yield as well as glycerol consumption indicated that l-proline might act as a potential anti-stress agent for the oleaginous yeast strain.

Microbial Oil Production from Lignocellulosic Biomass – Recent Development and Prospect

2014 ◽  
Vol 541-542 ◽  
pp. 397-403
Author(s):  
Zhang Nan Lin ◽  
Hong Juan Liu ◽  
Zhi Qin Wang ◽  
Jia Nan Zhang
Keyword(s):  
Lignocellulosic Biomass ◽  
Large Scale ◽  
Raw Materials ◽  
Oil Production ◽  
Renewable Resource ◽  
Raw Material ◽  
Biodiesel Production ◽  
Microbial Oil ◽  
Key Issues ◽  
Application Potential

Microbial oil is one of the ideal raw materials for biodiesel production because of its rapid reproduction and less influence by the climate and season variation. However, the high cost is one of the key issues that restricted its production in a large-scale. Lignocellulosic biomass, the cheap and renewable resource, might be the best raw material for microbial oil production by oleaginous microorganisms. Recent development on the microbial oil production from lignocellulosic biomass was summarized in this paper. Furthermore, the challenges and application potential of microbial oil were prospected.

scholarly journals Genetic engineering of microalgae lipid biosynthesis for sustainable biodiesel production

2021 ◽  
Vol 11 (3) ◽  
pp. 072-077
Author(s):  
Siti Zulaiha
Keyword(s):  
Genetic Engineering ◽  
Metabolic Pathways ◽  
Alternative Energy ◽  
Fossil Fuels ◽  
Lipid Production ◽  
High Growth ◽  
Lipid Biosynthesis ◽  
Production Costs ◽  
Biodiesel Production ◽  
Promising Alternative

Biofuel is one of the most promising alternative energy sources for reducing human reliance on fossil fuels. Microalgae has recently emerged as the most promising biofuel source. However, biofuels from microalgae are still not feasible to replace fossil fuels because of their high production costs, therefore, it is necessary to pick microalgae species with high growth rates and lipid content. Overexpression of lipid biosynthesis enzymes and inhibition of competitive metabolic pathways are two genetic engineering strategies that can be developed to assess microalgae lipid production. Malate and multienzyme enzymes (GPAT, LPAAT and DGAT) can be overexpressed in microalgae to boost lipid production. The strategy of blocking competitive metabolic pathways can be carried out through suppression of starch metabolism and lipid catabolism. The strategy of blocking competitive metabolic pathways has been carried out in several microalgae and is effective for enhancing lipid biosynthesis. Several mutations that block both the starch metabolic and lipid catabolic pathways can result in increased levels of microalgal lipid accumulation.

Sign in / Sign up

Export Citation Format

Share Document