CSOI: Beyond Silicon-on-Insulator Photonics

2022 ◽  
Vol 33 (1) ◽  
pp. 24
Author(s):  
Lin Chang ◽  
Garrett D. Cole ◽  
Galan Moody ◽  
John E. Bowers
Keyword(s):  
Silicon On Insulator

Structural changes in silicon-on-insulator material during post-implantation annealing

1986 ◽  
Vol 44 ◽  
pp. 736-737
Author(s):  
C. O. Jung ◽  
S. J. Krause ◽  
S.R. Wilson
Keyword(s):  
Integrated Circuits ◽  
Oxide Layer ◽  
High Speed ◽  
Structural Changes ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Quality ◽  
Radiation Hardened ◽  
Post Implantation ◽  
Very High

Silicon-on-insulator (SOI) structures have excellent potential for future use in radiation hardened and high speed integrated circuits. For device fabrication in SOI material a high quality superficial Si layer above a buried oxide layer is required. Recently, Celler et al. reported that post-implantation annealing of oxygen implanted SOI at very high temperatures would eliminate virtually all defects and precipiates in the superficial Si layer. In this work we are reporting on the effect of three different post implantation annealing cycles on the structure of oxygen implanted SOI samples which were implanted under the same conditions.

In Situ microscopy of the anodic etching of silicon

1995 ◽  
Vol 53 ◽  
pp. 232-233
Author(s):  
Frances M. Ross ◽  
Peter C. Searson
Keyword(s):  
Composite Structures ◽  
High Surface ◽  
High Surface Area ◽  
Chemical Properties ◽  
Selective Etching ◽  
Silicon On Insulator ◽  
Second Phase ◽  
Porous Layers ◽  
New Class ◽  
Porous Semiconductors

Porous semiconductors represent a relatively new class of materials formed by the selective etching of a single or polycrystalline substrate. Although porous silicon has received considerable attention due to its novel optical properties1, porous layers can be formed in other semiconductors such as GaAs and GaP. These materials are characterised by very high surface area and by electrical, optical and chemical properties that may differ considerably from bulk. The properties depend on the pore morphology, which can be controlled by adjusting the processing conditions and the dopant concentration. A number of novel structures can be fabricated using selective etching. For example, self-supporting membranes can be made by growing pores through a wafer, films with modulated pore structure can be fabricated by varying the applied potential during growth, composite structures can be prepared by depositing a second phase into the pores and silicon-on-insulator structures can be formed by oxidising a buried porous layer. In all these applications the ability to grow nanostructures controllably is critical.

Analysis of Silicon-On-Insulator Structures Formed By Oxygen Ion Implantation

1985 ◽  
Vol 43 ◽  
pp. 300-301
Author(s):  
N. Lewis ◽  
E. L. Hall ◽  
A. Mogro-Campero ◽  
R. P. Love
Keyword(s):  
Ion Implantation ◽  
Single Crystal ◽  
Single Crystal Silicon ◽  
Silicon Layer ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
High Dose ◽  
Crystal Silicon ◽  
Oxygen Ion ◽  
Oxygen Ion Implantation

The formation of buried oxide structures in single crystal silicon by high-dose oxygen ion implantation has received considerable attention recently for applications in advanced electronic device fabrication. This process is performed in a vacuum, and under the proper implantation conditions results in a silicon-on-insulator (SOI) structure with a top single crystal silicon layer on an amorphous silicon dioxide layer. The top Si layer has the same orientation as the silicon substrate. The quality of the outermost portion of the Si top layer is important in device fabrication since it either can be used directly to build devices, or epitaxial Si may be grown on this layer. Therefore, careful characterization of the results of the ion implantation process is essential.

Behavior of contact-silicided TFSOI gate structures

1994 ◽  
Vol 52 ◽  
pp. 860-861
Author(s):  
N. David Theodore ◽  
Juergen Foerstner ◽  
Peter Fejes
Keyword(s):  
Semiconductor Device ◽  
Series Resistance ◽  
Field Effect Transistors ◽  
Silicon Layer ◽  
Device Fabrication ◽  
Silicon On Insulator ◽  
Continuous Layer ◽  
Buried Oxide ◽  
Device Structures ◽  
Thin Silicon

As semiconductor device dimensions shrink and packing-densities rise, issues of parasitic capacitance and circuit speed become increasingly important. The use of thin-film silicon-on-insulator (TFSOI) substrates for device fabrication is being explored in order to increase switching speeds. One version of TFSOI being explored for device fabrication is SIMOX (Silicon-separation by Implanted OXygen).A buried oxide layer is created by highdose oxygen implantation into silicon wafers followed by annealing to cause coalescence of oxide regions into a continuous layer. A thin silicon layer remains above the buried oxide (~220 nm Si after additional thinning). Device structures can now be fabricated upon this thin silicon layer.Current fabrication of metal-oxidesemiconductor field-effect transistors (MOSFETs) requires formation of a polysilicon/oxide gate between source and drain regions. Contact to the source/drain and gate regions is typically made by use of TiSi2 layers followedby Al(Cu) metal lines. TiSi2 has a relatively low contact resistance and reduces the series resistance of both source/drain as well as gate regions

Defect reduction in oxygen implanted silicon-on-insulator material during high-temperature annealing

1989 ◽  
Vol 47 ◽  
pp. 604-605
Author(s):  
P. Roitman ◽  
B. Cordts ◽  
S. Visitserngtrakul ◽  
S.J. Krause
Keyword(s):  
High Temperature ◽  
Annealing Temperature ◽  
Silicon On Insulator ◽  
High Dose ◽  
High Temperature Annealing ◽  
High Current ◽  
Defect Reduction ◽  
Annealing Step ◽  
Multiple Cycle ◽  
Defect Densities

Synthesis of a thin, buried dielectric layer to form a silicon-on-insulator (SOI) material by high dose oxygen implantation (SIMOX – Separation by IMplanted Oxygen) is becoming an important technology due to the advent of high current (200 mA) oxygen implanters. Recently, reductions in defect densities from 109 cm−2 down to 107 cm−2 or less have been reported. They were achieved with a final high temperature annealing step (1300°C – 1400°C) in conjunction with: a) high temperature implantation or; b) channeling implantation or; c) multiple cycle implantation. However, the processes and conditions for reduction and elimination of precipitates and defects during high temperature annealing are not well understood. In this work we have studied the effect of annealing temperature on defect and precipitate reduction for SIMOX samples which were processed first with high temperature, high current implantation followed by high temperature annealing.

TEM study of buried cobalt disilicide layers formed by ion implantation: Identification of cobalt monosilicide inclusions

1990 ◽  
Vol 48 (4) ◽  
pp. 576-577
Author(s):  
A. De Veirman ◽  
J. Van Landuyt ◽  
K.J. Reeson ◽  
R. Gwilliam ◽  
C. Jeynes ◽  
...  
Keyword(s):  
Ion Implantation ◽  
Annealing Treatment ◽  
Silicon On Insulator ◽  
High Dose ◽  
Nitrogen Flow ◽  
Cobalt Disilicide ◽  
Transmission Electron ◽  
Beam Heating ◽  
Co Concentration ◽  
Silicon On Insulator Technology

In analogy to the formation of SIMOX (Separation by IMplanted OXygen) material which is presently the most promising silicon-on-insulator technology, high-dose ion implantation of cobalt in silicon is used to synthesise buried CoSi2 layers. So far, for high-dose ion implantation of Co in Si, only formation of CoSi2 is reported. In this paper it will be shown that CoSi inclusions occur when the stoichiometric Co concentration is exceeded at the peak of the Co distribution. 350 keV Co+ ions are implanted into (001) Si wafers to doses of 2, 4 and 7×l017 per cm2. During the implantation the wafer is kept at ≈ 550°C, using beam heating. The subsequent annealing treatment was performed in a conventional nitrogen flow furnace at 1000°C for 5 to 30 minutes (FA) or in a dual graphite strip annealer where isochronal 5s anneals at temperatures between 800°C and 1200°C (RTA) were performed. The implanted samples have been studied by means of Rutherford Backscattering Spectroscopy (RBS) and cross-section Transmission Electron Microscopy (XTEM).

The advancement of silicon-on-insulator (SOI) devices and their basic properties

2020 ◽  
Vol 23 (3) ◽  
pp. 227-252
Author(s):  
T.E. Rudenko ◽  
◽  
A.N. Nazarov ◽  
V.S. Lysenko ◽  
◽  
...  
Keyword(s):  
Silicon On Insulator ◽  
Basic Properties ◽  
Soi Devices

Method of Detecting Trace Metal Contamination in Thick-Film SOI Device

2005 ◽  
Author(s):  
Yasunori Goto ◽  
Hiroomi Eguchi ◽  
Masaru Iida
Keyword(s):  
Trace Metal ◽  
Thick Film ◽  
Metal Contamination ◽  
Semiconductor Device ◽  
Trace Element Analysis ◽  
Silicon On Insulator ◽  
Element Analysis ◽  
Trace Metal Contamination ◽  
Trace Metal Elements ◽  
Output Characteristics

Abstract In the automotive IC using thick-film silicon on insulator (SOI) semiconductor device, if the gettering capability of a SOI wafer is inadequate, electrical characteristics degradation by metal contamination arises and the yield falls. At this time, an automotive IC was made experimentally for evaluation of the gettering capability as one of the purposes. In this IC, one of the output characteristics varied from the standard, therefore failure analysis was performed, which found trace metal elements as one of the causes. By making full use of 3D perspective, it is possible to fabricate a site-specific sample into 0.1 micrometre in thickness without missing a failure point that has very minute quantities of contaminant in a semiconductor device. Using energy dispersive X-ray, it is possible to detect trace metal contamination at levels 1E12 atoms per sq cm. that are conventionally detected only by trace element analysis.

Sign in / Sign up

Export Citation Format

Share Document