scholarly journals 60 GHz Front-End Components for Broadband Wireless Communication in 130 nm CMOS Technology

2016 ◽  
Vol 21 (1) ◽  
pp. 67-77
Author(s):  
Vasilis Kolios ◽  
Konstantinos Giannakidis ◽  
Grigorios Kalivas
Keyword(s):  
Power Consumption ◽  
Phase Noise ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Total Power ◽  
Spectral Space ◽  
60 Ghz ◽  
Front End ◽  
Total Power Consumption ◽  
5 Ghz

Abstract The over 5 GHz available spectral space allocated worldwide around the 60 GHz band, is very promising for very high data rate wireless short-range communications. In this article we present two key components for the 60 GHz front-end of a transceiver, in 130 nm RF CMOS technology: a single-balanced mixer with high Conversion Gain (CG), reduced Noise Figure (NF) and low power consumption, and an LC cross-coupled Voltage Controlled Oscillator (VCO) with very good linearity, with respect to Vctrl, and very low Phase Noise (PN). In both circuits, custom designed inductors and a balun structure for the mixer are employed, in order to enhance their performance. The VCO’s inductor achieves an inductance of 198 pH and a quality factor (Q) of 30, at 30 GHz. The balun shows less than 1o Phase Imbalance (PI) and less than 0.2 dB Amplitude Imbalance (AI), from 57 to 66 GHz. The mixer shows a CG greater than 15 dB and a NF lower than 12 dB. In addition, the VCO achieves a Phase Noise lower than -106 dBc/Hz at 1 MHz offset, and shows great linearity for the entire band. Both circuits are biased with a 1.2 V supply voltage and the total power consumption is about 10.6 mW for the mixer and 10.92 mW for the VCO.

scholarly journals Analysis of CMOS Comparator in 90nm Technology with Different Power Reduction Techniques

2018 ◽  
Vol 8 (6) ◽  
pp. 4922
Author(s):  
Anil Khatak ◽  
Manoj Kumar ◽  
Sanjeev Dhull
Keyword(s):  
Power Consumption ◽  
Leakage Current ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Power Reduction ◽  
Total Power ◽  
Low Power Consumption ◽  
Power Gating ◽  
Reduction Techniques ◽  
Total Power Consumption

To reduce power consumption of regenerative comparator three different techniques are incorporated in this work. These techniques provide a way to achieve low power consumption through their mechanism that alters the operation of the circuit. These techniques are pseudo NMOS, CVSL (cascode voltage switch logic)/DCVS (differential cascode voltage switch) & power gating. Initially regenerative comparator is simulated at 90 nm CMOS technology with 0.7 V supply voltage. Results shows total power consumption of 15.02 μW with considerably large leakage current of 52.03 nA. Further, with pseudo NMOS technique total power consumption increases to 126.53 μW while CVSL shows total power consumption of 18.94 μW with leakage current of 1270.13 nA. More then 90% reduction is attained in total power consumption and leakage current by employing the power gating technique. Moreover, the variations in the power consumption with temperature is also recorded for all three reported techniques where power gating again show optimum variations with least power consumption. Four more conventional comparator circuits are also simulated in 90nm CMOS technology for comparison. Comparison shows better results for regenerative comparator with power gating technique. Simulations are executed by employing SPICE based on 90 nm CMOS technology.

scholarly journals A Novel Differential Log-Companding Amplifier for Biosignal Sensing

2016 ◽  
Vol 2016 ◽  
pp. 1-7
Author(s):  
Zigang Dong ◽  
Xiaolin Zhou ◽  
Yuanting Zhang
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Nonlinear Function ◽  
New Method ◽  
Total Power ◽  
Maximum Output ◽  
Output Current ◽  
Current Range ◽  
Symmetrical Configuration ◽  
Total Power Consumption

We proposed a new method for designing the CMOS differential log-companding amplifier which achieves significant improvements in linearity, common-mode rejection ratio (CMRR), and output range. With the new nonlinear function used in the log-companding technology, this proposed amplifier has a very small total harmonic distortion (THD) and simultaneously a wide output current range. Furthermore, a differential structure with conventionally symmetrical configuration has been adopted in this novel method in order to obtain a high CMRR. Because all transistors in this amplifier operate in the weak inversion, the supply voltage and the total power consumption are significantly reduced. The novel log-companding amplifier was designed using a 0.18 μm CMOS technology. Improvements in THD, output current range, noise, and CMRR are verified using simulation data. The proposed amplifier operates from a 0.8 V supply voltage, shows a 6.3 μA maximum output current range, and has a 6 μW power consumption. The THD is less than 0.03%, the CMRR of this circuit is 74 dB, and the input referred current noise density is166.1 fA/Hz. This new method is suitable for biomedical applications such as electrocardiogram (ECG) signal acquisition.

scholarly journals A Low Power Sigma-Delta Modulator with Hybrid Architecture

Sensors ◽  
2020 ◽  
Vol 20 (18) ◽  
pp. 5309
Author(s):  
Shengbiao An ◽  
Shuang Xia ◽  
Yue Ma ◽  
Arfan Ghani ◽  
Chan Hwang See ◽  
...  
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Supply Voltage ◽  
Total Power ◽  
Cmos Process ◽  
Hybrid Architecture ◽  
Sigma Delta Modulator ◽  
Dynamic Comparator ◽  
Flash Adc ◽  
Total Power Consumption

Analogue-to-digital converters (ADC) using oversampling technology and the Σ-∆ modulation mechanism are widely applied in digital audio systems. This paper presents an audio modulator with high accuracy and low power consumption by using a discrete second-order feedforward structure. A 5-bit successive approximation register (SAR) quantizer is integrated into the chip, which reduces the number of comparators and the power consumption of the quantizer compared with flash ADC-type quantizers. An analogue passive adder is used to sum the input signals and it is embedded in a SAR ADC composed of a capacitor array and a dynamic comparator which has no static power consumption. To validate the design concept, the designed modulator is developed in a 180 nm CMOS process. The peak signal to noise distortion ratio (SNDR) is calculated as 106 dB and the total power consumption of the chip is recorded as 3.654 mW at the chip supply voltage of 1.8 V. The input sine wave of 0 to 25 kHz is sampled at a sampling frequency of 3.2 Ms/s. Moreover, the results achieve a 16-bit effective number of bits (ENOB) when the amplitude of the input signal is varied between 0.15 and 1.65 V. By comparing with other modulators which were realized by a 180 nm CMOS process, the proposed architecture outperforms with lower power consumption.

scholarly journals Design of a very low-power, low-cost 60 GHz receiver front-end implemented in 65 nm CMOS technology

2011 ◽  
Vol 3 (2) ◽  
pp. 131-138 ◽  
Author(s):  
Michael Kraemer ◽  
Daniela Dragomirescu ◽  
Robert Plana
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Noise Figure ◽  
Low Cost ◽  
Cmos Technology ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Voltage Controlled Oscillator ◽  
60 Ghz ◽  
Front End

The research on the design of receiver front-ends for very high data-rate communication in the 60 GHz band in nanoscale Complementary Metal Oxide Semiconductor (CMOS) technologies is going on for some time now. Although a multitude of 60 GHz front-ends have been published in recent years, they are not consequently optimized for low power consumption. Thus, these front-ends dissipate too much power for battery-powered applications like handheld devices, mobile phones, and wireless sensor networks. This article describes the design of a direct conversion receiver front-end that addresses the issue of power consumption, while at the same time permitting low cost (due to area minimization by the use of spiral inductors). It is implemented in a 65 nm CMOS technology. The realized front-end achieves a record power consumption of only 43 mW including low-noise amplifier (LNA), mixer, a voltage controlled oscillator (VCO), a local oscillator (LO) buffer, and a baseband buffer (without this latter buffer the power consumption is even lower, only 29 mW). Its pad-limited size is 0.55 × 1 mm2. At the same time, the front-end achieves state-of-the-art performance with respect to its other properties: Its maximum measured power conversion gain is 30 dB, the RF and IF bandwidths are 56.5–61.5 and 0–1.5 GHz, respectively, its measured minimum noise figure is 9.2 dB, and its measured IP−1 dB is −36 dBm.

scholarly journals Towards Realization of a Low-Voltage Class-AB VCII with High Current Drive Capability

Electronics ◽  
2021 ◽  
Vol 10 (18) ◽  
pp. 2303
Author(s):  
Leila Safari ◽  
Gianluca Barile ◽  
Vincenzo Stornelli ◽  
Shahram Minaei ◽  
Giuseppe Ferri
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Harmonic Distortion ◽  
Cmos Technology ◽  
Current Drive ◽  
Total Power ◽  
High Signal ◽  
High Current ◽  
Class Ab ◽  
Total Power Consumption

In this paper, the implementation of a low-voltage class AB second generation voltage conveyor (VCII) with high current drive capability is presented. Simple realization and good overall performance are the main features of the proposed circuit. Proper solutions and techniques were used to achieve high signal swing and high linearity at Y, X and Z ports of VCII as well as low-voltage operation. The operation of the proposed VCII was verified through SPICE simulations based on TSMC 0.18 µm CMOS technology parameters and a supply voltage of ±0.9 V. The small signal impedance values were 973 Ω, 120 kΩ and 217 Ω at Y, X and Z ports, respectively. The maximum current at the X port was ±10 mA with maximum total harmonic distortion (THD) of 2.4% at a frequency of 1 MHz. Considering a bias current (IB) of 29 µA and output current at the X port (IX) of 10 mA, the current drive capability (IX/IB) of about 345 was achieved at the X port. The voltage swing at the Z port was (−0.4, 0.4) V. The THD value at the Z port for an input signal with 0.8 V peak-to-peak value and frequency of 1 MHz was 3.9%. The total power consumption was 0.393 µW.

scholarly journals 1.5-V CMOS Current Multiplier/Divider

2018 ◽  
Vol 8 (3) ◽  
pp. 1478 ◽  
Author(s):  
Jetsdaporn Satansup ◽  
Worapong Tangsrirat
Keyword(s):  
Low Voltage ◽  
Supply Voltage ◽  
Current Mode ◽  
Cmos Technology ◽  
Signal Frequency ◽  
Total Power ◽  
Total Power Consumption ◽  
Linearity Error ◽  
Low Supply Voltage ◽  
Circuit Technique

A circuit technique for designing a compact low-voltage current-mode multiplier/divider circuit in CMOS technology is presented.  It is based on the use of a compact current quadratic cell able to operate at low supply voltage.  The proposed circuit is designed and simulated for implementing in TSMC 0.25-m CMOS technology with a single supply voltage of 1.5 V.  Simulation results using PSPICE, accurately agreement with theoretical ones, have been provided, and also demonstrate a maximum linearity error of 1.5%, a THD less than 2% at 100 MHz, a total power consumption of 508 W, and -3dB small-signal frequency of about 245 MHz.

scholarly journals A TRANSISTOR LEVEL ANALYSIS FOR A 8-BIT VEDIC MULTIPLIER

2012 ◽  
pp. 78-83
Author(s):  
ARUN K PATRO ◽  
KUNAL N DEKATE
Keyword(s):  
Power Consumption ◽  
Digital Signal ◽  
Cmos Technology ◽  
Total Power ◽  
Vedic Multiplier ◽  
Total Power Consumption ◽  
Improved Performance ◽  
Almost All ◽  
Signal Processors ◽  
Level Analysis

Power and area efficient multiplier using CMOS logic circuits for applications in various digital signal processors is designed. This multiplier is implemented using Vedic multiplication algorithms mainly the "Urdhvatiryakbhyam sutra" , which is the most generalized one Vedic multiplication algorithm [1] . A multiplier is a very important element in almost all the processors and contributes substantially to the total power consumption of the system. The novel point is the efficient use of Vedic algorithm (sutras) that reduces the number of computational steps considerably compared with any conventional method . The schematic for this multiplier is designed using TANNER TOOL. The design is then verified in T-SPICE using 0.18 um CMOS technology library file. The analysis is made for various voltages across a range of 2.5V to 5V, to validate the design. A CMOS digital multiplier, with low power consumption and high linearity is proposed. The results prove that the proposed multiplier consumes 80% less power compared to the gate level analysis done earlier. The core area of the proposed multiplier is 737 um2 . Paper presents a systematic design methodology for this improved performance digital multiplier based on Vedic mathematics.

scholarly journals Design of Area Efficient, Low-Power and Reliable Transmission Gate-based 10T SRAM Cell for Biomedical Application

2021 ◽  
Author(s):  
Aswini Valluri ◽  
◽  
Sarada Musala ◽  
Muralidharan Jayabalan ◽  
◽  
...  
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Biomedical Application ◽  
Cmos Technology ◽  
Total Power ◽  
Silicon Area ◽  
Transmission Gate ◽  
Read Operation ◽  
Sram Cell ◽  
Total Power Consumption

There is an immense necessity of several kilo bytes of embedded memory for Biomedical systems which typically operate in the sub-threshold domain with perfect efficiency. SRAMs (Static Random Access Memory) dominates the total power consumption and the overall silicon area, as 70% of the die has been occupied by them. This brief proposes the design of a Transmission gate-based SRAM cell for Bio medical application eliminating the use of peripheral circuitry during the read operation. It commences the read operation directly with the help of Transmission gates with which the data stored in the storage nodes can be read, instead of using the precharge and sense amplifier circuits which suits better for the implantable devices. This topology offers smaller area, reduced delay, low power consumption as well as improved data stabilization in the read operation. The cell is implemented in 45nm CMOS technology operated at 0.45V.

scholarly journals A LOW PHASE NOISE, POWER EFFICIENT VOLTAGE CONTROLLED OSCILLATOR USING 0.18-μM CMOS TECHNOLOGY

2014 ◽  
pp. 256-259
Author(s):  
AJIT SAMASGIKAR
Keyword(s):  
Power Consumption ◽  
Phase Noise ◽  
Tuning Range ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Noise Power ◽  
Voltage Controlled Oscillator ◽  
Power Efficient ◽  
Sustained Oscillations ◽  
Low Phase Noise

A low phase noise, power efficient VCO using UMC 0.18μm CMOS technology has been proposed in this paper. The proposed VCO has a tuning range of 9.71GHz to 9.9GHz, with a phase noise of -79.88 dBc/Hz @ 600kHz offset. The Vtune ranging between 1V - 1.5V generates sustained oscillations. The maximum power consumption of the VCO is 11.9mW using a supply voltage of 1.8V with ±10% variation.

Design of a 10-Bit High Performance Current-Steering DAC with a Novel Nested Decoder Based on Domino Logic

2015 ◽  
Vol 24 (06) ◽  
pp. 1550086 ◽  
Author(s):  
Masoud Nazari ◽  
Leila Sharifi ◽  
Meysam Akbari ◽  
Omid Hashemipour
Keyword(s):  
Power Consumption ◽  
High Performance ◽  
Dynamic Range ◽  
Logic Gates ◽  
Cmos Technology ◽  
Total Power ◽  
Current Steering ◽  
Domino Logic ◽  
Chip Area ◽  
Total Power Consumption

In this paper, a 10-bit 8-2 segmented current-steering digital-to-analog converter (DAC) is presented which uses a novel nested binary to thermometer (BT) decoder based on domino logic gates. High accuracy and high performances are achieved with this structure. The proposed decoder has a pipelining scheme and it is designed symmetrically in three stages with repeatable logic gates. Thus, power consumption, chip area and the number of control signals are reduced. The proposed DAC is simulated in 0.18-μm CMOS technology and the spurious-free dynamic range (SFDR) is 65.3 dB over a 500 MHz output bandwidth at 1 GS/s. Total power consumption of the designed DAC is only 23.4 mW while the digital and analog supply voltages are 1.2 and 1.8 V, respectively. The active area of the proposed DAC is equal to 0.3 mm2.

Sign in / Sign up

Export Citation Format

Share Document