Waste paper as a cheap source of natural fibre to reinforce polyester resin in production of bio-composites

2016 ◽  
Vol 36 (5) ◽  
pp. 441-447 ◽  
Author(s):  
Sekhar Das ◽  
Santanu Basak ◽  
Manik Bhowmick ◽  
Sajal K. Chattopadhyay ◽  
Manoj G. Ambare
Keyword(s):  
Tensile Strength ◽  
Polyester Resin ◽  
Low Cost ◽  
Crystallinity Index ◽  
Natural Fibre ◽  
Sem Analysis ◽  
Fibre Content ◽  
Waste Paper ◽  
Fibre Direction ◽  
Composite Samples

Abstract A low cost composite material was prepared by using waste newspaper and polyester resin. The waste newspaper used in the study was characterized by chemical and X-ray diffraction (XRD) methods, and tensile strength was measured. Waste newspaper contains holocellulose of about 83.2% and the crystallinity index of the newspaper is 64.2. Composite samples were fabricated with three different fibre contents, namely 25%, 33%, and 48% (by weight). It was observed that on increasing the fibre content from 25% to 48%, the tensile strength and the modulus also increased by 54%–40%, respectively, along the fibre direction. It was observed that with 48% (w/w) fibre content, the waste paper composite yielded 70 MPa tensile strength and 6 GPa modulus in the fibre direction and 19 MPa tensile strength and 2.41 GPa modulus in the cross direction. The newspaper composite samples were characterized by thermogravimetric analysis, Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) analysis.

SYNTHESIS AND CHARACTERISATION OF WOVENROVING GLASS MAT FOR EPOXYCOMPOSITES

2020 ◽  
Vol 15 (4) ◽  
Author(s):  
Mahesh Mallampati ◽  
Sreekanth Mandalapu ◽  
Govidarajulu C
Keyword(s):  
Tensile Strength ◽  
Glass Fiber ◽  
Low Cost ◽  
Weight Ratio ◽  
High Strength ◽  
Hardness Test ◽  
Industrial Applications ◽  
Sem Analysis ◽  
Low Thermal Expansion ◽  
Manufacturing Techniques

The composite materials are replacing the traditional materials because oftheir superior properties such as high tensile strength, low thermal expansion, high strength to weight ratio, low cost, lightweight, high specific modulus, renewability and biodegradability which are the most basic & common attractive features of composites that make them useful for industrial applications. The developments of new materials are on the anvil and are growing day by day. The efforts to produce economically attractive composite components have resulted in several innovative manufacturing techniques currently being used in the composites industry. Generally, composites consist of mainly two phases i.e., matrix and fiber. In this study, woven roving mats (E-glass fiber orientation (-45°/45°,0°/90°, - 45°/45°),UD450GSM)were cut in measured dimensions and a mixture of Epoxy Resin (EPOFINE-556, Density-1.15gm/cm3), Hardener (FINE HARDTM 951, Density- 0.94 gm/cm3) and Acetone [(CH3)2CO, M= 38.08 g/mol] was used to manufacture the glass fiber reinforced epoxy composite by hand lay-up method. Mechanical properties such as tensile strength, SEM analysis, hardness test, density tests are evaluated.

Tensile Properties of Pineapple Leaf Fibre Reinforced Unsaturated Polyester Composites

2014 ◽  
Vol 695 ◽  
pp. 159-162 ◽  
Author(s):  
Januar Parlaungan Siregar ◽  
Tezara Cionita ◽  
Dandi Bachtiar ◽  
Mohd Ruzaimi Mat Rejab
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Fiber Length ◽  
Interfacial Adhesion ◽  
Unsaturated Polyester ◽  
Fibre Length ◽  
Tensile Modulus ◽  
Natural Fibre ◽  
Fibre Content ◽  
Polyester Composites

In recent years natural fibres such as sisal, jute, kenaf, pineapple leaf and banana fibres appear to be the outstanding materials which come as the viable and abundant substitute for the expensive and non-renewable synthethic fibre. This paper investigate the effect of fibre length and fibre content on the tensile properties of pineapple leaf fibre (PALF) reinforced unsaturated polyester (UP) composites. PALF as reinforcement agent will be employed with UP to form composite material specimens. The various of fiber length (<0.5, 0.5–1, and 1-2 mm) and fibre content (0, 5, 10 and 15 % by volume) in UP composite have been studied. The fabrication of PALF/UP composites used hand lay-up process, and the specimens for tensile test prepared follow the ASTM D3039. The result obtained from this study show that the 1-2 mm fibre length has higher tensile strength (42 MPa) and tensile modulus (1344 MPa) values compared to fibre length of <0.5 mm (30 MPa and 981 MPa) and 0.5-1 mm (35.40 MPa and 1020 MPa) respectively. Meanwhile, for the effect of various fibre content in study has shown that the increase of fibre content has decreased in tensile strength dan tensile modulus of composites. The increase of fibre content due to poor interfacial bonding and poor wetting of the fibre by unsaturated polyster. The treatment of natural fibre are suggested in order to improve the interfacial adhesion between natural fibre and the unsaturated polyester.

scholarly journals Effect of Jute Fibre Orientation and Percentage on Strength of Jute Fibre Reinforced Concrete

2020 ◽  
Vol 9 (3) ◽  
pp. 1767-1770
Keyword(s):  
Tensile Strength ◽  
Reinforced Concrete ◽  
Dynamic Properties ◽  
Low Cost ◽  
Plain Concrete ◽  
Natural Fibre ◽  
Fibre Reinforced Concrete ◽  
Jute Fibre ◽  
Micro Cracks ◽  
Crack Arrester

The demerits of plain concrete are its lesser tensile strength, not significant ductility and poor resistance to cracking. Due to propagation of internal micro cracks in plain concrete causes decrease in tensile strength, hence leads concrete to brittle fracture. Addition of fibres behaves like crack arrester and enhances the dynamic properties of concrete. In India natural fibres such as bamboo, coir, jute, sisal, pineapple, banana, ramie etc are high available. Jute is a useful natural fibre for concrete reinforcement due to its easy availability and low cost. In this research, the experiments related to Jute fibre reinforced concrete (JFRC) are done by taking different fibre percentage and the compressive strength and modulus of rapture value observed. This JFRC can replace plain concrete and wood in many cases for example in door and window panels, inclined roof slabs, partition walls etc

scholarly journals The Effect of Deinking Process on Bioethanol Production from Waste Banknote Paper

Processes ◽  
2020 ◽  
Vol 8 (12) ◽  
pp. 1563
Author(s):  
Omid Yazdani Aghmashhadi ◽  
Ghasem Asadpour ◽  
Esmaeil Rasooly Garmaroody ◽  
Majid Zabihzadeh ◽  
Lisandra Rocha-Meneses ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Enzymatic Hydrolysis ◽  
Crystallinity Index ◽  
Sugar Concentration ◽  
Waste Paper ◽  
Process Efficiency ◽  
Bioethanol Production ◽  
Ph Values ◽  
Optimal Values ◽  
Chemical Pretreatments

The aim of this paper is to study the effect of reinking and pretreatment of waste banknote paper on its usability in the bioethanol production process. To this end, the tensile strength of worn banknote paper was first studied at different pH values. The sample with the lowest tensile strength was considered for the next sections. In the deinking process, NaOH at different concentrations (1%, 2%, 3%, and 4%) and in combination with ultrasonic treatment was applied. After deinking the pulp, two acidic and alkaline chemical pretreatments with concentrations of 1%, 2%, 3%, and 4% were used independently and in combination with ultrasonic. Enzymatic hydrolysis, following fermentation with Scheffersomyces stipitis, and crystallinity measurements were used to confirm the efficiency of the pretreatments. RSM Design Expert software was used to determine the optimal values by considering the three variables—enzyme loading, ultrasonic loading, and contact time for waste paper deinked (WPD) and waste paper blank (WPB) pulps. The results indicated that repulping was the most efficient at pH = 2. In deinking, the highest brightness was obtained using 3% NaOH in combination with ultrasonic. Between the acid and alkaline pretreatment, the acid treatment was more appropriate according to the resulting sugar concentration and weight loss. XRD tests confirmed that the lowest crystallinity index was obtained in the sample pretreated with 4% sulfuric acid in combination with ultrasonic. The highest sugar concentration in the enzymatic hydrolysis step was 92 g/L for WPD and 81 g/L for WPB. For the fermentation at 96 h, the highest ethanol concentration and process efficiency achieved were 38 g/L and 80.9% for WPD and 31 g/L and 75.04% for WPB, respectively. Our research shows that the deinking process can widen the utilization potential of waste banknote paper in biorefinery processes.

scholarly journals MECHANICAL AND MICROSTRUCTURAL PROPERTIES OF BRASS REINFORCED WITH COCONUT SHELL ASH POWDER

2021 ◽  
Vol 15 (2) ◽  
pp. 234-243
Author(s):  
Oluseyi Orisadare ◽  
Ayodeji S. Olawore ◽  
Michael O. Ibiwoye ◽  
Eyitayo A. Ponle ◽  
Omolola T. Odeyemi ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Impact Energy ◽  
Low Cost ◽  
Stir Casting ◽  
Sem Analysis ◽  
Coconut Shell ◽  
Matrix Composites ◽  
Coconut Shell Ash ◽  
Mechanical And Microstructural Properties ◽  
Hardness Values

Metal matrix composites (MMCs) are materials in which metals are reinforced with other materials preferably of lower cost to improve their properties. In this present study, Brass /Coconut Shell Ash powder (CSAp) composites having 0%, 5%, 10% and 15% weight CSAp were fabricated by stir-casting method. The tensile strength of the MMCs is in the order 15% > 10% >5% > 0% of CSAp. Hardness of the MMCs increases slightly with increase in the percentage body weight of CSAp, in the order 15% > 10% >5% > 0% of CSAp. The highest impact energy of 61 J was obtained for 5% CSAp. However, significant improvement in tensile strength and hardness values was noticeable at the 15%. Scanning Electron Microscopy (SEM) analysis of the MMCs shows dendritic structures formation, the reinforcing particles (CSAp) are visible and clearly delineated in the microstructure. Hence, this study has established that reinforcing brass matrix with coconut shell ash particles can result in the production of low cost brass composites with enhanced tensile strength, hardness and impact energy values.  

Poly(∊-Caprolactone) Composites Reinforced with Short Abaca Fibres

2003 ◽  
Vol 11 (5) ◽  
pp. 359-367 ◽  
Author(s):  
Mitsuhiro Shibata ◽  
Ryutoku Yosomiya ◽  
Noritaka Ohta ◽  
Atsushi Sakamoto ◽  
Hiroyuku Takeishi
Keyword(s):  
Tensile Strength ◽  
Acetic Anhydride ◽  
Tensile Properties ◽  
Weight Fraction ◽  
Natural Fibre ◽  
Fibre Content ◽  
Melt Mixing ◽  
The Matrix ◽  
Poly Caprolactone ◽  
Butyric Anhydride

The tensile properties of poly( ∊-caprolactone) (PCL) composites reinforced with short abaca fibres (length ca. 5 mm) prepared by melt mixing and subsequent injection molding were investigated and compared with PCL composites reinforced with glass fibres (GF). The influence of fibre content and surface esterification of the natural fibre on the tensile properties was evaluated. The tensile strength and moduli of all the PCL/abaca composites increased with increasing fibre content. All the PCL/abaca composites had a higher tensile strength than the PCL/GF composites when the fibre weight fraction was the same. The tensile strength of the PCL/abaca composites was improved by surface esterification of the abaca with acetic anhydride or butyric anhydride in the presence of pyridine, because of the increase in the interfacial adhesiveness between the matrix polyester and the esterificated fibre, as is obvious from the SEM photographs.

scholarly journals Mechanical properties of papercrete

2018 ◽  
Vol 162 ◽  
pp. 02016 ◽  
Author(s):  
Harith Zaki ◽  
Iqbal Gorgis ◽  
Shakir Salih
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Low Cost ◽  
Construction Material ◽  
Splitting Tensile Strength ◽  
Waste Paper ◽  
Additional Material ◽  
Sustainable Building

This paper studies the uses, of waste paper as an additional material in concrete mixes. Papercrete is a term as the name seems, to imply a mixture of paper and concrete. It is a new, composite material using waste paper, as a partial addition of Portland cement, and is a sustainable, building material due to, reduced amount of waste paper being put to use. It gains, latent strength due to presence of hydrogen bonds in microstructure of paper. Papercrete has been, reported to be a low cost alternative, building construction, material and has, good sound absorption, and thermal insulation; to be a lightweight and fire-resistant material. The percent of waste paper used (after treating) namely (5%, 10%, 15% and 20%) by weight of cement to explore the mechanical properties of the mixes (compressive strength, splitting tensile strength, flexural strength, density), as compared with references mixes, it was found that fresh properties affected significantly by increasing the waste paper content. The compressive strength, splitting tensile strength, flexural strength and density got decreased with increase in the percentage of paper.

PEMANFAATAN GLISERIN DARI RESIDU GLISERIN SEBAGAI PLASTICIZER UNTUK PEMBUATAN BIOPLASTIK DENGAN BAHAN BAKU PATI BONGGOL PISANG KEPOK

2017 ◽  
Vol 5 (4) ◽  
pp. 26-32 ◽  
Author(s):  
Azaria Robiana ◽  
M. Yashin Nahar ◽  
Hamidah Harahap
Keyword(s):  
Tensile Strength ◽  
Hydrogen Bonding ◽  
Fatty Acid ◽  
Maximum Yield ◽  
Sem Analysis ◽  
Water Molecules ◽  
Banana Weevil ◽  
Gelatinization Temperature ◽  
Recharge Area ◽  
Maximum Quantity

Glycerin residue is waste oleochemical industry that still contain glycerin. To produce quality and maximum quantity of glycerin, then research the effect of pH acidification using phosphoric acid. Glycerin analysis includes the analysis of pH, Fatty Acid and Ester (FAE), and analysis of the levels of glycerin. The maximum yield obtained at pH acidification 2 is grading 91,60% glycerin and Fatty Acid and Ester (FAE) 3,63 meq/100 g. Glycerin obtained is used as a plasticizer in the manufacture of bioplastics. Manufacture of bioplastics using the method of pouring a solution with varying concentrations of starch banana weevil (5% w/v and 7% w/v), variations of the addition of glycerin (1 ml, 3 ml, 5 ml and 7 ml), and a variety of gelatinization temperature (60°C, 70°C, and 80°C). Analysis of bioplastics include FTIR testing, tensile strength that is supported by SEM analysis. The results obtained in the analysis of FTIR does not form a new cluster on bioplastics starch banana weevil, but only a shift in the recharge area only, it is due to the addition of O-H groups originating from water molecules that enter the polysaccharide through a mechanism gelatinitation that generates interaction hydrogen bonding strengthened. The maximum tensile strength of bioplastics produced at a concentration of starch 7% w/v, 1 ml glycerine and gelatinization temperature of 80°C is 3,430 MPa. While the tensile strength bioplastic decreased with increasing glycerin which can be shown from the results of SEM where there is a crack, indentations and lumps of starch insoluble.

Fabrication and Characterization of Biocomposite Using Grewia Optiva Fibre (i.e. Bhimal) Reinforced Polyvinyl Alcohol (PVA)

2015 ◽  
Vol 1105 ◽  
pp. 51-55 ◽  
Author(s):  
K.M. Gupta ◽  
Kishor Kalauni
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Fibre ◽  
Fabrication Method ◽  
View Point ◽  
Engineering Material ◽  
Fibre Composites ◽  
Grewia Optiva ◽  
Fabrication And Characterization

Bhimal fibres are quite a newer kind of bio-degradable fibres. They have never been heard before in literatures from the view point of their utility as engineering material. These fibres have been utilized for investigation of their properties. Characterization of this fibre is essential to determine its properties for further use as reinforcing fibre in polymeric, bio-degradable and other kinds of matrix. With this objective, the fabrication method and other mechanical properties of Bhimal-reinforced-PVA biocomposite have been discussed. The stress-strain curves and load-deflection characteristics are obtained. The tensile, compressive, flexure and impact strengths have been calculated. The results are shown in tables and graphs. The results obtained are compared with other existing natural fibre biocomposites. From the observations, it has been concluded that the tensile strength of Bhimal-reinforced-PVA biocomposite is higher than other natural fibre composites. Hence these can be used as reinforcement to produce much lighter weight biocomposites.

scholarly journals Properties of Low-Cost WPCs Made from Alien Invasive Trees and rLDPE for Interior Use in Social Housing

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2436
Author(s):  
Abubakar Sadiq Mohammed ◽  
Martina Meincken
Keyword(s):  
Tensile Strength ◽  
Water Absorption ◽  
Social Housing ◽  
Low Cost ◽  
Production Costs ◽  
Low Density Polyethylene ◽  
Low Grade ◽  
Low Density ◽  
Invasive Trees ◽  
Recycled Low Density Polyethylene

Low-cost wood–plastic composites (WPCs) were developed from invasive trees and recycled low-density polyethylene. The aim was to produce affordable building materials for low-cost social housing in South Africa. Both raw materials are regarded as waste materials, and the subsequent product development adds value to the resources, while simultaneously reducing the waste stream. The production costs were minimised by utilising the entire biomass of Acacia saligna salvaged from clearing operations without any prior processing, and low-grade recycled low-density polyethylene to make WPCs without any additives. Different biomass/plastic ratios, particle sizes, and press settings were evaluated to determine the optimum processing parameters to obtain WPCs with adequate properties. The water absorption, dimensional stability, modulus of rupture, modulus of elasticity, tensile strength, and tensile moduli were improved at longer press times and higher temperatures for all blending ratios. This has been attributed to the crystallisation of the lignocellulose and thermally induced cross-linking in the polyethylene. An increased biomass ratio and particle size were positively correlated with water absorption and thickness swelling and inversely related with MOR, tensile strength, and density due to an incomplete encapsulation of the biomass by the plastic matrix. This study demonstrates the feasibility of utilising low-grade recycled polyethylene and the whole-tree biomass of A. saligna, without the need for pre-processing and the addition of expensive modifiers, to produce WPCs with properties that satisfy the minimum requirements for interior cladding or ceiling material.

Sign in / Sign up

Export Citation Format

Share Document